Transcript
Operating Notes Power Supply
FCC Compliance Statement
This dome camera can operate on 24 VAC or 12 VDC.
Operating Conditions Avoid: • Viewing bright objects (for example, light fixtures) for extended periods • Operating or storing the unit in the following locations. • Extremely humid, dusty, hot/cold environments (where the operating temperature is outside the recommended range of 14°F to 122°F [-10°C to +50°C]) • Close to sources of powerful electromagnetic radiation, such as radio or TV transmitters • Close to fluorescent lamps or objects reflecting light • Under unstable light sources (may cause flickering)
Warnings (where applicable to your locale)
Quick Install Guide
Information to the User: This equipment has been tested and found to comply with the limits for a Class B digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • • • •
Document 800-04882 – Rev E – 11/09
Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment to an outlet on a circuit different from that to which the receiver is connected Consult the dealer or a radio/TV technician for help.
Installation and servicing should be performed only by qualified and experienced technicians to conform to all local codes and to maintain your warranty.
Caution
WARNING!
This Class B digital apparatus complies with Canadian ICES-003.
The use of CSA Certified/UL Listed Class 2 power adapters is required to ensure compliance with electrical safety standards.
4 Inch Dome Camera
1 Preparation 2 Camera Mounting
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product (applicable in the European Union and other European countries with separate collection systems). This product should be disposed of, at the end of its useful life, as per applicable local laws, regulations, and procedures.
Manufacturer’s Declaration of Conformance
Product Dimensions
Contact Information
3 Camera Adjustment
The manufacturer declares that the equipment supplied with this guide is compliant with the essential protection requirements of the EMC directive 2004/108/EC and the Low Voltage Directive (LVD) 2006/95/EC, conforming to the requirements of standards EN 55022 for emissions, EN 50130-4 for immunity, and EN60065 for Electrical Equipment safety.
Contents Flush mount
Surface mount
5.74” (145.9 mm)
∅ 5.74” (∅ 145.9 mm) ∅0.22” (∅5.5 mm)
M 6” M 4.7 21.0 1 (
)
2.63” (66.9 mm)
4.06” (106.1 mm)
2.04” (51.75 mm)
3.97” (100.8 mm)
Fully assembled camera
Mounting templates
www.honeywellvideo.com +1.800.796.CCTV (North America only)
[email protected]
Document 800-04882 – Rev E – 11/09
© 2009 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any
means without written permission from Honeywell Systems Group. The information in this publication is believed to be accurate in all respects. However, Honeywell Systems Group cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
Hardware kit
Document 800-04882 – Rev E – 11/09
This guide
1
2
Preparation
Skirt
Flush Mount
Surface Mount
1. Remove the Dome Cover a.
Loosen the three security screws, then remove the dome.
b.
Gently pull the inner liner free of the two notches in the housing.
c.
Set the dome and liner aside.
d.
Loosen the three screws connecting the skirt and the base, then remove the base. Continue with step 2 “Prepare the Mounting Surface” below.
3
Camera Mounting
Camera Adjustment
Adapter plate (use is optional)
Skirt
Screws (not supplied)
A = Tilt rotation B = Horizontal rotation* C = Pan rotation
Base
C
Base
Base
Legend
B
* If necessary, loosen the screw that locks the gimbal assembly in place, before adjusting the camera.
M4 screws (supplied)
Inner liner
Dome
M4 screws (supplied)
After ➋ mounting and ➌ adjusting the camera, attach the dome cover:
a.
Secure the skirt to the ceiling or wall using the appropriate screws, not supplied.
a.
Attach the inner liner to the base until the liner clicks into place.
b.
Tuck the cables in the area outside the posts. (See “Connect the Wiring”.)
b.
Secure the dome enclosure to the base with the three security screws.
c.
Secure the camera base to the skirt using the appropriate M4 screws, supplied.
2. Prepare the Mounting Surface (Surface or Flush Mount) Note Surface mount preparation shown. Use the appropriate mounting template to: a.
Mark the holes as required.
b.
Insert the screw anchors into the holes.
•
•
For adapter plate installations, secure the base with the appropriate M4 screws, supplied. When not using the adapter plate, use screws appropriate to secure the base to the wall or ceiling.
A
Optional Camera Settings Focus lever (top)
Level L H V-Phase + –
Zoom lever (bottom)
4S Electrical Junction Box (optional) Surface Mount
Flush Mount Electrical box (not supplied) Mode setting DIP switches = ON = OFF
Adapter plate
3. Connect the Wiring
Skirt
Caution Do not touch or damage the black vent!
24 VAC/12 VDC power connector
Video output connector
Base
Base
M4 screws (supplied)
a.
a
a.
Connect the video output connector.
b.
Connect the 24 VAC/12 VDC power connector.
c.
If necessary, tuck the wires into the space outside the posts (grayed area).
Monitor out
Screws (not supplied)
Connect the wiring. If you need to contain the connection within the camera housing, then try the method shown below. b
Screws (not supplied)
b. c.
M4 screws (supplied)
Secure the skirt to the electrical box using 2 appropriate screws (not supplied).
a.
Tuck the cables in the area outside the posts. (See “Connect the Wiring”.)
b.
Secure the camera base to the skirt using the appropriate M4 screws, supplied.
Secure the adapter plate to the 4S electrical box using the appropriate screws, not supplied. Secure the camera base to the adapter plate using the appropriate M4 screws, supplied.
.
Picture Brightness
The LEVEL screw compensates for the iris level. L (low) darkens the picture. H (high) brightens the picture.
Phase Adjustment
The V Phase Adjustment Pot adjusts the phase difference between cameras. Switch 7 must be ON to activate Line lock (AC only).
DIP Switches (Refer to your camera model) Default settings are shown in bold.
SW
High Res + TDN
High Res
Std Res
1
DC/AES
DC/AES
DC/AES
2
AWB/ATW
AWB/ATW
AWB/ATW
3
BLC ON/OFF
BLC ON/OFF
BLC ON/OFF
4
AGC ON/OFF
AGC ON/OFF
AGC ON/OFF
5
TDN
Not used
FLK/OFF
6
FLK ON/OFF
FLK ON/OFF
LL ON/OFF
7
LL ON/OFF
LL ON/OFF
Not available
8
Not used
Not used
Not available
