Transcript
Outdoor siren
4073
Description External siren designed for easy installation, sabotage prevention and weather resistance. The siren was designed to work both with E46ADCN or E49 power supply and with buffered E47ADCN power supply; the siren is tamper-proof against breaking/opening. The siren is also protected by an anti-foaming device installed on the electronic board. It is equipped with a patented anti-tampering anchorage system.
1
NOTE: the siren is not compatible with systems where the 4600/4 (or 4600/1) central unit and the E47ADCN power supply are installed.
2
3 Technical data
Input clamps maximum absorption: normal operation alarm battery recharge with E47ADCN battery recharge with E46ADCN/E49 Input / output and power supply: Battery slot: Alarm operating time: Alarm sound intensity: Frequency: Flashing: Flashes per minute: Weight (without battery): IP protection index: Operating ambient temperature: Self-protected against removal and opening Strength degree Maximum system consumption for 1 or 2 sirens (the buffer time increases with 2 sirens)
20 mA 20 mA 50 mA 250 mA Two-wire 12V 2.0 – 7.2Ah 15 min 105 dB(A) at 1 m 1500Hz flash 60 2.1Kg IP44 (-25) – (+55) °C IK08 300 mA
Legend 1. External plastic cover 2. Acoustic indicator 3. Light indicator
Dimensions
107 mm
332 mm
217,4 mm
MQ01017-d-EN
20/06/2016
1
Outdoor siren
4073
Installation of the outdoor siren
- Remove the four screws (1) and take off the external cover (2). - Use a drilling template (3) to position the hole (4) in correspondence of the wire outlet pipe and trace the 4 holes for the fastening screws (5), the hole for the tamper screw (6) and the hole for the anti-tampering anchorage (7) (Patent Pending). NOTE: use a Ø 6mm bit for drilling the holes (*). (*) It is recommended to use screws with a diameter of 3.5 to 4.5 mm depending on the type of dowel used, countersunk.
5
1 3
1 2
7
4
6
1 5
1
- Insert the plastic dowels in the holes. - Break the pre-drilled hole (11) to insert the anti-tampering system screw . - Partially tighten the two top screws and attach the siren to them (8). - Tighten the two bottom screws (9). Fully tighten the four fastening screws and the anti-tampering system screw. - Tighten the tamper screws (10), without forcing it in case of installation on uneven surfaces. - Place the battery in the appropriate slot without connecting the Faston clamps. See table below for battery type: Power supply
Main battery
E49
7Ah
Secondary battery 2 Ah (**)
E46ADCN
7Ah
2 Ah (**)
E47ADCN
2Ah
2Ah
(**) If a second siren is installed to have additional signaling and it is not necessary to extend the la system operating time in buffer mode (mains power failure) a 2Ah battery can be installed.
11
Slot battery
- On the internal board, connect the power supply pair (BUS) to the appropriate clamp (see next page).
10
- Connect the battery connectors, only with the BUS powered - Position the cover and tighten the four fixing screws (1) on the wall base. Siren LED flash
Before working on the siren, put the system in maintenance mode. The flashing of the siren LED, when exiting maintenance mode, indicates the BUS polarity inversion.
8 1
Wall
9
Not compatible with 4072A/4072L sirens. In case of a second siren on the system, install another 4073.
1 1
MQ01017-d-EN
2
If the red BUS led turns on, reverse the BUS polarity.
1
LED indications
LED
ON
Green power supply LED
Power supply enabled
Power supply disabled
Red LED BUS
BUS reversed polarity
BUS correct polarity
Red LED battery
Battery reversed polarity
Battery correct polarity
20/06/2016
OFF
Outdoor siren
4073
Configuration switch and LED
Power supply type Second siren
Connector battery
Anti-foaming sensors Battery LED
Enabling the anti-foaming device Power supply LED LED BUS 1
2
SW1
4
3
SW2
1 SW1 2 3 SW2 4
1 SW1 2 3 SW2 4
Speaker connector
BUS connection plug-in clamp
1 SW1 2 3 SW2 4 To change the configuration, put the control unit in maintenance mode and disconnect the batteries and the SCS bus
1 SW1 2 3 SW2 4
Main siren System with power supply E46ADCN or E49
1 SW1 2 3 SW2 4
Secondary siren
1 SW1 2 3 SW2 4
1 SW1 2 3 SW2 4 1 SW1 2 3 SW2 4
1 SW1 2 3 SW2 4
1 SW1 2 3 SW2 4
If there is a primary network power failure, operation is guaranteed If you want to guarantee a longer operating time for the system, a for the system by the battery installed inside the siren. SW2 second siren can be installed for the system, configuring it as shown 1 SW1 2 3 4 This solution allows using only one battery instead of the two used by traditional systems, thus above. 1 SW1 2 3 SW2 4 reducing maintenance and increasing system reliability by maintaining security. Configure the siren as shown above. 1 SW1 2 3 SW2 4
System with power supply E47ADCN
1 SW1 2 3 SW2 4
1 SW1 2 3 SW2 4
1 SW1 2 3 SW2 4
1 SW1 2 3 SW2 4
Its presence is useful as a signaling device, but it is not required because the system buffer If you want to install a second siren in order to have two signaling 1 SW1 2 3 SW2points, 4 you can install a second siren on the same system, battery will be connected to the power supply. The internal siren slot is used to accommodate 1 SW1 2 3 SW2 4 the siren self-supply battery and, therefore,1a SW1 2Ah battery be sufficient. configuring it as shown above. SW2 2 3will 4 Configure this siren as shown above.
1 SW1 2 3 SW2 4 Protection anti-foaming
1 SW1 2 3 SW2 4 1 SW1 2 3 SW2 4
1 SW1 2 3 SW2 4
SW1the 1 using 2 SW2 3 SW2 4 You can activate the anti-foaming protection configuration switch. SW2 = ON (Anti-foaming protection activated)
MQ01017-d-EN
20/06/2016
3
