Transcript
Notes
Required Connection Optional Connection • Refer to the Device Compatibility Document (A15378) for compatible devices. • Total MPS-400 current drawn cannot exceed 6 A. • Each SLC loop can connect up to 198 addressable devices. • Part numbers for removable terminal blocks (TBx): 2-position (02082); 4-position (02084); 6-position (02086); 8-position (02088).
Primary AC Power: 120 VAC 50/60 Hz 3 A or 240 VAC 50/60 Hz 1.5 A
1 + Circuit 1 – regulated, filtered, nonresettable power (1.25 A) to 2 – ICM-4/ICE-4 (NAC circuits), annunciator circuits, UDACT (use bell power harness PN 71093)
Hot Neutral
Earth
Term In + Term In – Term Out + Term Out –
Bwn
Org
Red
Blk
Org
Red
Blk Bwn
25 23 21 19 17 15 13 11 9 7 5 3 1
26 24 22 20 18 16 14 12 10 8 6 4 2
115V
JP6 J3
J5 J4
Cut to enable supervision of 4XTM optional plug-in module
1 2 3 4
7 8
7 8
J1
2 1 4 3 6 5 8 7 10 9 12 11 14 13
NAC 4
Ground Fault LED
TB2
TB1
Ground + 24 VDC – Power ground nc nc + 5 VDC Ground
THER
- 9
9 1
-
8
1 -
+ 8
2
+
7
2 +
+ 7
COM
3 4
NO
NC
6 5
B501B Base
2(+)
3
1(-)
LOOP
-
ADT-BGX-101L
+
ADDRESS TYPE ION
3 -
- 6
4 +
5
PHOTO THER
M500M
M500CH
- 9
9
EIA-485 Terminal mode interface to CRT-2 and ADT-LCD-80 (6,000 ft. max.) EIA-485 ACS Mode interface
1 2
1 2 34
TB3
TB5
TB4
J2
1 -
1 -
2 +
2 +
3 -
3 -
4 +
4 +
M500X
1
-
2
+ COM
3 4
NO
NC
8
1 -
+ 8
7
2 +
+ 7
6
3 -
- 6
5
4 +
5
M500CH
M500X
M500M
1 2 3 4 5 6
TB6 1
2 3 4 5 6
TB6 (SLC 2) – Unimode 400 only
Group of panel modules (such as ICM-4, CRM-4) in second cabinet row (ADT-CAB-B3) or third cabinet row (ADT-CAB-C3)
2 1 4 3 6 5 8 7 10 9 12 11 14 13
Ribbon Row Cable (PN 71088) to panel modules 5-8 (such as ICM-4, CRM-4) in ADT-CAB-B3, ADT-CAB-C3, or ADT-CAB-D3 cabinets only
J4
Relays TB4 (Supervisory) and TB5 (Security) can be set to Alarm relays by setting slide switches SW4 and SW5. • Slide SW5 to top position to set TB5 to Alarm; • Slide SW4 to top position to set TB4 to Alarm;
Membrane Keypad Connector
P5.1P5.8
P6.1P6.8
P7.1P7.8
P8.1P8.8
P1.1P1.8
P2.1P2.8
P3.1P3.8
P4.1P4.8
Ribbon Row Cable (PN 71088) to panel modules 1-4 (such as ICM-4, CRM-4)
SW4/SW5 shown set to top position (Alarm)
MPS-400
J2
1 2 3 4
JP5 – 4XTM Option Module Trouble/Supervisory
J7
Optional 4XTM plug-in module
+ 5 VDC + 24 VDC nc nc Ground Ground Ground Ground
SW4 AC Power On LED
TB10
1 2 3
1 2 3
P6 J6
PHOTO
Earth Ref A – SLC 2 Style 6/7 – B – SLC 2 – A + SLC 2 Style 6/7 + B + SLC 2 +
8 7 6 5 4 3 2 1
J8
1 2 3 4 TB8
NAC 3
SW5 Ground + 24 VDC – Power ground + 5 VDC Ground 1 + 5 VDC Ground
TB6
NAC 2
A– A+ B– B+
Local Charger
1 2 3
A– A+ B– B+
1 2 3 4 5 6 7 8
NAC 1
A– A+ B– B+
TB4 1 2 3
J6
P1 J1 8 7 6 5 4 3 2 1
P1
JP1
C NC NO
4 5 6 7 8
F1
10A 3AG, 32V PN 12046
C NC NO
P6 CPU Power Harness 1 PN 75396 (ADT-CAB-400AA) 2 PN 75395 (ADT-CAB-3 Series) 3
1 2 3 1 2 3 TB5 1 2 3 4 TB7 1 2 3 4 TB9
Supervisory Security
P2
Prim
Sec
TB2
120/240 VAC Select Switch
TB3
A– A+ B– B+
Sec
Prim
1 2 3 4 56
C NC NO C NC NO
S9
Alarm Trouble
6 7
ION
Earth Ref A – SLC 1 Style 6/7 – B – SLC 1 – A + SLC 1 Style 6/7 + B + SLC 1 +
4 5
A– A+ B– B+
3
ADT-BGX-101L
ADDRESS TYPE
Four-wire SLC – Typical wiring of a four-wire (Style 6) SLC loop (supervised and power-limited)
ADT-UDACT, ADT-ACM-8R, ADT-NIB-96, AMG-1, ADTUZC-256, RPT-485, ADTLDM-32 (6,000 ft. max.)
1 2 3 4
1 2 TB1
- +
LOOP
ACS + to ACS Annunciators (640 ACS – control points), ADT-LCD-80,
+–
Ground Cable PN 71033
B501B Base
EIA-232 Terminal interface to CRT-2, modem, or personal computers with Uni•Tility upload/download utility (50 ft. Max.) If using a modem, reverse TX and RX.
Pin 3 Pin 2 Pin 7
Tx Tx Rx Rx Ref Ref
3 + Circuit 2 – regulated, filtered, nonresettable power (1.25 A) to 4 – ICM-4/ICE-4 (NAC circuits), annunciator circuits, ADT-UDACT (use bell power harness PN 71093) 5 + Circuit 3 – regulated, filtered resettable (1.25 A) to 6 – four-wire smoke detectors or ACS annunciators, power-limited and supervision required NAC Style Y Unused NAC NAC Style Z (Class B) Connection Note: Each NAC can (Class A) Connection (2.25 A max.) (2.25 A max.) use up to 2.25 A Connection ELR 2.2K 1/2W (2.25 A max.) ELR 2.2K 1/2W maximum; up to 6 A for all NACs combined. +–
Batt. +
Pin 3 EIA-232 printer interface for EDP-listed Pin 2 equipment (PRN-4/Keltron printer Pin 7 connection shown) DB-25 Connector
Tx Tx Rx Rx Ref Ref
DC Power Outputs (24 VDC)
Batt. –
Battery Power Cable PN 71070
Two-wire SLC – Typical wiring of a two-wire (Style 4) SLC loop (supervised and power-limited)
DB-25 Connector
TB3-TB6 – Form-C relays rated at 2A, 30 VDC resistive.
JP2 Ground fault disable
Bell circuit logic and power supply trouble signals
J9 1 2 34
J3
25 23 21 19 17 15 13 11 9
Auxiliary Trouble Cable – AMG (P9), AVPS-24 (P2) PN 75098 (24 in.) PN 71033 (60 in.)
(Includes ADT-CPU-300 and ADT-CPU-400)
Group of panel modules (such as ICM-4, CRM-4) in first, second, or third cabinet row. If installing modules in the first cabinet row, P3 and P4 are not used.
7 5 3 1
26 24 22 20 18 16 14 12 10 8 6 4 2
25 23 21 19 17 15 13 11 9
MPM-2 – Optional voltmeter
ADT-CPU
7 5 3 1
P3 26 24 22 20 18 16 14 12 10 8
6 4 2
ADT-CPU EIA-485 ACS Connection TB4-1 TB4-2
Power Ribbon Cable PN 75398 (ADT-CAB-400AA) PN 75394 (ADT-CAB-3 Series)
6
Security Tamper Switch Input – STS-200 (ADT-CAB-400AA); STS-1 (ADT-CAB-3 Series) Cable PN 75148
P2
4
P3
Aux. Trouble cable to MPS-400 J4 PN 75098 (24 in.) PN 71033 (60 in.)
P9
Zone Coder Input – ADT-UZC-256 TB1 Cable PN 71093
P1 Accessory Cable ADT-CAB-400AA – 75396 ADT-CAB-X3 – 75100
AMG-1, AMG-E, or ATG-2
Unimode 300/Unimode 400 Basic System Connections Document 50712:B Revision: B ECN 98-213 JSR 05/11/98
