Transcript
Model 5225 Series Shielded Enclosure Safety Information
The following views and setup instructions apply to a standard configuration of the ETS-Lindgren Model 5225 Series Shielded Enclosure. Components may vary for custom Model 5225 configurations. Contact ETS-Lindgren for questions regarding your configuration.
For complete safety information, see the Product Information Bulletin.
ONLY QUALIFIED PERSONNEL should install, operate, or service this equipment. WARRANTY
CONTACT ETS-LINDGREN PRIOR TO SERVICING. Servicing (or modifying) the unit by yourself may void your warranty. If you attempt to service the unit by yourself, disconnect all electrical power before starting. There are voltages at many points in the instrument that could, if contacted, cause personal injury. Only trained service personnel should perform adjustments and/or service procedures upon this instrument. Capacitors inside this instrument may still be CHARGED even when instrument is disconnected from its power source.
Front, Right Side
Front, Left Side
Warranty Information For warranty information, see the Product Information Bulletin.
IEC power connector
Back View
Antenna patch with SMA connectors
Lid handle (on front)
Inside View
USA Headquarters 1301 Arrow Point Drive Cedar Park, TX 78613 Phone: (512) 531-6400
[email protected] Please see www.ets-lindgren.com for a list of all ETS-Lindgren offices.
Antenna patch with SMA connectors
Location for equipment under test (EUT)
© Copyright 2008–2010 by ETS-Lindgren L.P. All Rights Reserved. No part of this document may be copied by any means without written permission from ETS-Lindgren L.P. The ETS-Lindgren logo is a trademark of ETS-Lindgren L.P.
399296, Rev B
Revision/Date: A, Initial Release - September, 2008 B, Adjust graphics, add specifications - October, 2010
www.ets-lindgren.com
Fiber optic feedthrough
Filtered DB-9 feedthrough
www.ets-lindgren.com
Model 5225 Series Shielded Enclosure
Shielding Specifications Before connecting components, read Safety Information on the back page of this document.
100 dB, 5 MHz–6 GHz
Attenuation
Filter Specifications Setup Instructions
1. Raise the lid handle to open the door of the Model 5225.
2. (As required by the testing you want to perform) Attach cables to the SMA connectors on the antenna patches.
Current
10 Amps
Voltage
100—250 VAC
Insertion Loss
100 dB, 5 MHz–18 GHz
Operating Frequency
0 Hz–60 Hz
Electrical Specifications
• 30 dB to 35 dB minimum
Coupling Loss
at the 2.54 band for low frequency antennas
• Better than -36 dB from
3. (As required by the testing you want to perform) Connect cables to the DB-9 and fiber optic feedthroughs.
5 GHz to 6 GHz for high frequency antennas
• (~25 dB at 5.5 GHz) using identical antennas at 10 cm from antenna surface
4. Place EUT inside the Model 5225 and connect cables as required.
5. Attach a power cable to the IEC power connector.
Typical Coupling Loss Repeatability
+/- 1 dB
Typical Internal RF Absorption
2 GHz–6 GHz
Typical RF Isolation
2 GHz–6 GHz >80 dB
Physical Specifications 6. Lower the lid handle to close the door of the Model 5225. Connectors
7. Apply power to the Model 5225. Perform testing as required.
Note: ETS-Lindgren may substitute a similar part or new part number with the same functionality for another part/part number. Contact ETS-Lindgren for questions about part numbers and ordering parts.
• SMA feedthrough (2) • Type N (1) • Fiber optic feedthrough (1) • IEC power (1) • Filtered DB-9 feedthrough (1)
Internal Dimensions (Absorber to Absorber)
Length: 60.5 cm (23.8 in) Width: 50.3 cm (19.8 in) Height: 32.3 cm (12.7 in)
External Dimensions
Length: 71.1 cm (28.0 in) Width: 60.9 cm (24.0 in) Height: 43.2 cm (17.0 in)
Weight
22.0 kg (48.6 lb)
www.ets-lindgren.com
