Transcript
www.chantproductions.com
About chant™ Hardware of distinctive design and uncompromising finish, developing themes that carry form through function – from the entry way statement to the finest cabinetry and window fittings. We met Paul Mason in 1994. His timeless designs inspired us to establish Chant Productions. The front section of this catalogue details both Paul’s original and his latest creations. The remainder of the catalogue illustrates the results of working closely with clients determined to remain faithful to their vision of detailing and design – thank you for your inspiration and support. Graham, Nathan and Byron Chant
1
www.chantproductions.com Visit our website for the latest in product additions. This complete catalogue is also available as a PDF on our website.
Unit of Measure All dimensions are specified in millimetres (mm) throughout this catalogue.
References to other sections The catalogue has the following helpful ‘refer to’ panels. The other sections referred to carry either related products or other relevant information.
2
refer chant™ refer Mason Product Finishes Escutcheons 4–5 26 – 27
refer chant™ Escutcheons 68 – 69
refer chant™ Technical 104 – 113
8 10 12 14 16 20 22 24 26 28
chant™ More about chant™ Bow Sabre Arc Luna Cobra Delta Swan Cubic Line Angle Rod Stop Round/Royal chant™ Escutcheons
32 34 36 38 40 44 46 48 50 52 58 60 62 64 68
73 73 74 75 76 77 78 79 80 83 84 86 87 88 89 90 98 100 101
mason
About Paul Mason Samba Swim Nile Comma Rib River Flute Mason Escutcheons Mason Lever Handles
Door Stops Hold Backs Push Plates Pull Handle Back Plates Flush Pulls Recessed Pulls Privacy Flush Pulls Locking Flush Pulls Flush Sliding Bolts Flush Pull Bolts Square Bolts Hinges Handrail Supports Casement Fasteners Telescopic Security Stays Mortice Locks & Latches Twin Bolts Cylinders and Turns chant™ Custom Manufacture
Technical Handing of Handles chant™ Lever Handles on Rose chant™ Door Handle Plates Pull Handles Attaching Plates Door Morticing Equipment
105 105 106 110 113 114
General Maintenance Finish Options, Bronze and “Living Finishes Product Warranty
118 118 119
chant™
Mason
Accessories
119
accessories
1 4
technical
About chant™ chant™ Product Finishes
chant product finishes
chant™ Product Finishes These colours are indicative only, subject to limitations in the printing process.
Polished Chrome Plate/PCP
Layers of bright nickel and chrome on a polished
surface.
Satin Chrome Plate Velvet/SCPV
Layers of satin nickel and chrome on a
polished surface.
Satin Chrome Plate Brushed/SCPB
Layers of bright nickel and chrome on a
brushed surface.
Sand Polished Chrome/SPC
This is a shot-blasted finish providing a textured surface, which is then polished chrome plated.
Black Chrome/BC
A durable, deep black, polished black chrome finish.
Satin Black Chrome/SBC
A durable, satin black chrome finish.
Gold/GLD 22 carat gold plate finish with a rich gold colour. Standard thickness is 0.5 micron.
Finish Options All hardware is available in Combination or Split finishes.
Combination Finishes Individual components of different finishes are assembled into a lever or pull handle, ie. satin chrome plate velvet lever and rose cover and polished chrome plate rose and handle boss.
Split Finishes This is where different sections of a pull or lever handle can be processed in two finishes. The blend between the finishes can be ‘crisp’ along a ridge line, or ‘soft’ over a contoured area of the handle, eg. combination of sand polished chrome and polished chrome. Contact chant™ to discuss your requirements.
4
Examples of natural patinas which occur over time
Bronze Metal and “Living Finishes” All of our products are made of brass as the base metal, which is used for the electroplated finishes, including copper and satin nickel plate. Almost all of our products are also available in bronze as the base metal. Refer to page 119 for more detailed information on Living Finishes.
Polished Bronze/PBZ This will age naturally and develop its own patina over time depending on the prevailing climatic conditions and wear patterns. The ultimate finish will be a rich semi-gloss bronze patina surface, often showing the random grain structure of the bronze. Satin Bronze Aged/SBZA The surface is satin finished by brushing, then aged to provide a matt bronze surface. The colour of this finish will, over time, adjust to its own natural satin patina depending upon the prevailing climatic conditions and wear patterns.
chant product finishes
Original finish
Weathered Bronze/WBZ A bead-blasted surface on bronze, then aged to provide a matt bronze surface. The colour of this finish will also continue to evolve over time.
Sand Bronze Aged/SABA
A shot-blasted surface on bronze, then aged to provide a matt bronze, textured surface. The colour of this finish will also continue to evolve over time.
Earth Bronze/EBZ A unique process creating a random spectrum of earthy hues. Colour will naturally vary from product to product (we would recommend that a physical sample is sighted, before specifying).
Charcoal Bronze/CBZ This deep, matt ‘coloured’ dark grey finish is the outcome of a specialised process on bronze metal.
Copper Plate/COP
A thick copper layer plated onto the base metal, left uncoated, which will acquire a rich red-brown patina over time.
Weathered Copper/WCOP
A thick copper layer plated onto the base metal, then bead-blasted and ‘aged’ to a matt red-brown colour, which will continue to evolve a natural patina over time.
Satin Nickel Plate/SNP A layer of satin nickel on a polished surface. It will oxidise to a minor degree over time, please refer to additional information, “Living Finishes” on page 119.
Polished Brass Uncoated/PBU
This will need polishing with proprietary metal cleaners to maintain the surface, or left to age naturally to a yellow-brown patina.
5
Mason Swim PM12 Pull Handle
mason
About Paul Mason When you look at a door handle by Paul Mason you see a product of over three decades of research and development. The door furniture has emerged as an integral part of his career as a highly respected sculptor and designer – from the hands of a versatile master craftsman who has earned an international reputation for sculptural work with a refined aesthetic sensibility. Paul’s work as an artist can be found in the collections of public galleries such as the Auckland Museum and Te Papa Tongarewa, New Zealand; The Powerhouse Museum, Sydney; The Renwick, Washington, USA, and in private collections worldwide. Accolades have included being sent by the Crafts Council to teach in India in 1979. He taught at Elam School of Fine Art in the early 1980s and in 1985 was appointed cultural ambassador by the New Zealand government. He has received several QEll Arts Council grants and many commissions, and has exhibited widely, nationally and internationally. In 1998 he was nominated for the prestigious Seppelt Contemporary Art Award in Australia. His work has developed, in both scale and intent, from inspired pieces of jewellery, inlaid wooden boxes and vessels in metals and stone to commissions to design furniture and fittings for many private and public interiors including the National Library of New Zealand. Paul’s more recent exhibition and commissioned works have been made of granite and marble, exploring mass and surface texture, and expressing the relationship between stone and water.
8
In the early 1990s Paul designed his first door handle, Samba, for his own home. It was sculptural and tactile, with more than a passing aesthetic reference to his minimalist sculptures. Interest from architects and word of mouth led to development of the range. Paul met Graham Chant in 1994 – it was the beginning of a fruitful partnership. Graham formed Chant Productions in 1996 to bring the Samba and Swim door handles into commercial production. Over the next two years the Nile, Comma and Rib suites were introduced to the market. It is Paul’s interest in sculptural form that is brought into play in the range of Mason door furniture. The door handles bring art to the door surface, satisfying the eye and inviting touch. One can sense the sculptor’s hands defining the sensuous forms which transcend fashion. That timelessness translates into being able to complement any interior design statement.
Text by Helen Schamroth
9
Samba Pull Handles Samba PM00–800
Samba PM00 –1200
Samba PM01
Samba PM02 50
mason samba
60
210 170
300
360 250
555
250 800
400
55
1200
20
30 40
60
80
Example: Samba PM00 –1200 on a 2400mm high door
46
54
Left hand Samba Pull Handles shown. All Samba Pull Handles are available left hand or right hand. The PM01 Pull Handle has an offset of 20mm on the fixing holes to provide a balanced vertical visual alignment, particularly when they are mounted in pairs on double doors.
80
Note: One pair of Samba PM00 –1200 Pull Handles weigh approximately 18kg. Please ensure door and structure are sufficently strong to support this added weight. Available in standard mounting options.
10
If the Samba PM00 –1200 and 800 Pull Handles are being used on glass doors, 12mm holes are required. Mounting bolts are M8 (8mm diameter).
refer chant™ refer Mason Product Finishes Escutcheons 4–5 26 – 27
refer Mason Lever Handles 28 – 29
refer chant™ Technical 104 – 113
Samba PM02
Samba PM01
11
Swim Pull Handles Swim PM09
Swim PM10
Swim PM11
Swim PM12 45
60
100
mason swim
150 290
150
250
350
410
600 60
10
Swim PM13 600
20
1000
65
20 100
25
70
Example: Swim PM09 on a 2400mm high door
PM09 – PM12 Pull Handles: The offset of the fixing holes on these handles provide a balanced vertical visual alignment, particularly when they are mounted in pairs on double doors.
170
55
Left hand Swim Pull Handles shown. All Swim Pull Handles are available left hand or right hand. Note: One pair of Swim PM09 Pull Handles weigh approximately 16kg. Please ensure the door and structure are sufficently strong to support this added weight. Available in standard mounting options.
30 40 26
80
If the Swim PM09 or PM10 Pull Handles are being used on glass doors, 12mm holes are required. Mounting bolts are M8 (8mm diameter).
Swim Lever Handle/Fixed Handle
Swim Door Knocker
Swim PM14
Swim PM19
63
Swim PM15 63
56
160
170
63
Swim PM15S
63
140
170
57 35
Left hand handles shown. All pull and lever handles are available left hand or right hand.
Swim Cabinet Handles Swim PM16
Swim PM18 20
20 32
12
Swim PM17
65
95
30
32
95
30
refer chant™ refer Mason Product Finishes Escutcheons 4–5 26 – 27
refer Mason Lever Handles 28 – 29
refer chant™ Technical 104 – 113
Swim PM16
Swim PM14
Swim PM12
13
Nile Pull Handles Nile PM20 –1000
Nile PM20 –750
Nile PM21
Nile PM23 30
40
60
90
120
Nile PM22
200
110
mason nile
200 340 300 54
510
750
450 60
600
1000
Nile Pull Handles are non-handed Nile Lever Handles are reversible.
72
80
Note: One pair of Nile PM20 –1000 Pull Handles weigh 14kg. Please ensure the door and structure are sufficently strong to support this added weight. Available in standard mounting options.
Example: Nile PM20 –1000 on a 2400mm high door
If the Nile PM20 –1000 or PM20 –750 Pull Handles are being used on glass doors, 12mm holes are required. Mounting bolts are M8 (8mm diameter). 90
Nile Lever Handle/Fixed Handle
Nile Door Knocker
Nile PM24
Nile PM28
60
Nile PM25 60
Nile PM26 60
12 160
160
63
63
140
170
57 35
65
Nile Cabinet Handle Nile PM29 10 90
14
50
30
refer chant™ refer Mason Product Finishes Escutcheons 4–5 26 – 27
refer Mason Lever Handles 28 – 29
refer chant™ Technical 104 – 113
Nile PM29
Nile PM25
Nile PM22
15
Comma Pull Handles Comma PM32
Comma PM31
mason comma
25
Comma PM33
Comma PM36 16
23
25
110
150
160
240 360
250 350
480
42
50
10 55
50
15 80
60
25 100
60
Comma Lever Handle/Fixed Handle Comma PM34
Comma PM35
Left hand Comma Pull Handles shown. All Comma Pull Handles are available left hand or right hand. Comma Lever Handles are not handed and are reversible.
55
58
175
145
57
63
Comma Cabinet Handles Comma PM37
Comma PM38
96
114
24
16
28
refer chant™ refer Mason Product Finishes Escutcheons 4–5 26 – 27
refer Mason Lever Handles 28 – 29
refer chant™ Technical 104 – 113
Comma PM37
Comma PM34
Comma PM32
17
Mason Nile PM24 Lever Handle
Rib Pull Handles Rib PM42
Rib PM41
17
20
25
25
Rib PM46
Rib PM43
100
154 170
240
mason rib
250 360
350
26
43
480 29
30
55
65
75
31
Rib Lever Handle/Fixed Handle Rib PM44 54
Rib PM45
Rib Pull Handles are non-handed. The Rib Lever Handles are reversible.
54
170
145
57
63
Rib Cabinet Handles Rib PM48
96
Rib PM49
110 160
12
22 12
20
174
27
refer chant™ refer Mason Product Finishes Escutcheons 4–5 26 – 27
refer Mason Lever Handles 28 – 29
refer chant™ Technical 104 – 113
Rib PM48
Rib PM44
Rib PM42
21
River Pull Handles River PM50
River PM51
River PM52
River PM53
87 150 190
mason river
185
375
200
200
500
620 250
34
900
520
36
38
60
53
58
Example: River PM50 on a 2400mm high door
River Pull Handles are non-handed. The River Lever Handle is reversible. Available in standard mounting options. If the River PM50 Pull Handles are being used on glass doors, a 12mm hole is required. Mounting bolts are M8 (8mm diameter).
40
63
River Lever Handle River PM54 60
160
63
22
refer chant™ refer Mason Product Finishes Escutcheons 4–5 26 – 27
refer Mason Lever Handles 28 – 29
refer chant™ Technical 104 – 113
River PM54
River PM51
23
Flute Pull and Cabinet Handles Flute PM61
Flute PM62
Flute PM63
centres
mason flute
centres centres
12.5
17
38
46
54
22
Flute PM61 / PM62 / PM63 Pull Handles Sizes available (centres specified in mm): PM61: 300/450/600 PM62: 200/300/450 PM63: 128/160/192/224/256
Flute Lever Handle Flute PM64
Flute Handles are non-handed. The Flute Lever Handle is reversible.
50
160
63
24
17
refer chant™ refer Mason Product Finishes Escutcheons 4–5 26 – 27
refer Mason Lever Handles 28 – 29
refer chant™ Technical 104 – 113
Flute PM64
Flute PM63
Flute PM61
25
mason escutcheons
Mason Escutcheons PM100 Cylinder Escutcheon
PM105 Profile Cylinder Escutcheon
Use with Legge 990 MF Series, Lockwood 3500 Series, Astra mortice locks (Australasia) and Union (UK). Requires a minimum lock cylinder projection beyond the door surface of 14mm. The maximum door thickness with standard length cylinders is 46mm. For thicker doors use extended cylinders or PM103 Cylinder Escutcheon. For Union 2041 mortice lock with standard double cylinder, maximum door thickness is 35mm, or 53mm with extended double cylinder. Fastened with a socket set-screw on the underside. To specify: PM100/Finish.
Use with all profile cylinders. The radiused edge of this escutcheon complements the domed lever handle rose. Used when there is limited distance between cylinder length and door thickness. To specify: PM105/Finish
PM101 Turn Escutcheon The turn mechanism is fastened to the door with screws, then concealed by a ‘screw-on’ cover. Key bars to suit locks as detailed. A – 6mm x 2mm bar for Legge 990 MF Series and Lockwood 3500 Series mortice locks. (Australasia) B – 3/16” square spindle for Yale 4600, 8600 and 8700, and Schlage L Series mortice locks (USA) These spindles have a 2mm C – 4.5mm square spindle flat extension bar when D – 7.0mm square spindle ordered with PM102 E – 7.6mm square spindle Emergency Turn. Add suffix F – 8.0mm square spindle ET to order code e.g. To G – 5.0mm square spindle specify: PM101/Finish/ET H – 6.0mm square spindle J – 3/16” square spindle on the diamond ( ) for Accurate Locks (USA) K – 10mm x 3mm recess to suit chant™ Profile Cylinder Turn Adaptor 1241 etc. To specify: PM101/A, B, etc/Finish
PM102 Emergency Turn Escutcheon The turn mechanism is fastened to the door with screws, then concealed by a ‘screw-on’ cover. The turn is operated by the key bar on PM101 Turn Escutcheon above. To specify: PM102/Finish
PM102i Emergency Turn/Indicator Escutcheon The turn mechanism is fastened to the door with screws, then concealed by a ‘screw-on’ cover. The turn is operated by the key bar on PM101 Turn Escutcheon above. The red and green colour indicator behind the turn button shows the lock status. To specify: PM102i/Finish
PM103 Cylinder Escutcheon
PM106A and PM106B Recessed Cylinder Rings PM106 A X = 5mm (3/16”) PM106 B X = 6.5mm (1/4”) For Yale, Schlage etc cylinders. To specify: PM106A or B/Finish
X
For Legge 990 Series Mortice Locks
PM107B Pull/Turn For SAB Profile Cylinder Mortice Locks Pull turns are fitted on the inside of entrance doors to withdraw the latch bolt, when key entry is used on the outside. The turn base is securely fastened to an adaptor plate which is fixed to the side of the lock case prior to installation in the door. Depending on the lock used, specify the spindle bar type required from the chart opposite for turn escutcheons: typically A, E or F. Refer to page 113 for an exploded view of the fastening of the Pull Turn to the lock. To specify: PM107A or B/Finish
PM108 Profile Cylinder Escutcheon Use with all profile cylinders. The domed style of this escutcheon complements the domed lever handle rose. This requires a cylinder barrel of minimum 26mm more than the thickness of the door. Fastened with socket set-screw on the underside. To specify: PM108/Finish
PM109A Privacy Bolt/Turn Assembly This includes a 60mm backset privacy bolt, PM101 Turn Escutcheon and PM102 Emergency Turn Escutcheon. To specify: PM109/Finish
PM109B Privacy Bolt/Turn Assembly with Indicating Emergency Escutcheon This includes a 60mm backset privacy bolt, PM101 Turn Escutcheon and PM102i Emergency Turn/Indicator Escutcheon. To specify: PM109B/Finish
PM104 Profile Cylinder Escutcheon
26
44
PM107A Pull/Turn
Use with Union 2241 mortice lock where there is insufficient distance between the cylinder and lever rose for the PM100 Escutcheon. Doors thicker than 50mm will require an extended cylinder. Fastened with socket set-screw on the underside. To specify: PM103/Finish
Use with all profile cylinders, particularly with locks where there is insufficient distance between the cylinder and lever rose to use the PM105 Cylinder Escutcheon. Fastened with a socket set-screw on the underside. To specify: PM104/Finish
30
refer chant™ Product Finishes 4–5
PM100
PM104
PM101
PM105
PM102
PM107
PM102i
PM108
PM103
27
mason lever handles
Mason Lever Handles on Rose Lever Handles PM24, PM25, PM26, PM34, PM35, PM44, PM45, PM54 and PM64 on rose are symmetrical handles, and can easily be reversed on site to suit the door handing, by removing a stop-screw and key, rotating the handle and replacing the key and stop-screw. The PM14, PM15 and PM15S handles, which are not symmetrical, must be ordered to the correct handing required. Unless otherwise specified, all lever handles have a return spring within the rose for positive handle return.
Fixing Centre/Rose Types for PM14, PM15, PM24, PM25, PM34, PM44, PM54, PM64 Lever Handles Type A – 50.8mm centres at 45º for: – Tubular latches, 60mm backset or longer – Legge 990 MF Series and Lockwood 3500 Series Mortice Locks Type B – 39.5mm centres, horizontal for: – Profile Cylinder Mortice Locks: • AGB, CES, chant™, CISA, Dorma, FSB, GSV, Häfele, JADO, KFV, SAB • Legge 8762, 57mm backset – Oval Cylinder Mortice Locks: • Astra Brass and Astra S Series • Legge 990 MF • Union 2041, 127mm backset (has the lock cylinder horizontally in line with the lever handle) • Union 2241, 57mm and 82.5mm backsets – Mortice Latch: Union 2677, 57mm backset – Tubular Latch: Dalco 12002 Type C – 39.5mm centres, vertical for: – Tubular latches, 60mm backset or longer – NT Falcon Mortice Lock (USA) Type D – 39.5mm centres at 56º for: – Yale 4600, 8600, 8700 Series Mortice Locks (USA) Type E – 39.5mm centres at 45º for: – Schlage L Series Mortice Locks (USA) Type F – 38mm centres, unsprung rose with tie-screw fixing between the roses for: – GSV Locks, 3201Z, 3211Z, 3212Z, 3801Z Mortice Locks 3234 Mortice Latch Type G – 38mm centres, with unsprung roses. The mounting bases are tie-screw fixed through the door and lock, covered with the roses to provide concealed fixing, then the handles are fixed to the spindle on each side of the door for: – Profile cylinder mortice locks that have 38mm horizontal fixing centres and strong return springs to support the lever handle. • BKS, CES, Dorma, FSB, Häfele
Fixing Centre/Rose Types for PM15S, PM26, PM35, PM45 Handles Type H – 38mm centres, horizontal for: – Profile Cylinder Mortice Locks: • AGB, CES, chant™, CISA, Dorma, FSB, GSV, Häfele, JADO, KFV, SAB • Legge 8762, Imperial G7000, 57mm backset, etc – Oval Cylinder Mortice Locks: • Astra Brass and Astra S Series • Legge 990 MF • Union 2041, 127mm backset (has the lock cylinder horizontally in line with the lever handle) • Union 2241, 57mm and 82.5mm backsets – Mortice Latch : Union 2677, 57mm backset – Tubular Latch : Dalco 12002 Type I – 38mm centres, vertical for: Tubular latches, 60mm backset or longer Type J – 41mm centres, horizontal for: Lockwood 3500 Series Mortice Locks (Australia) Type K – 41mm centres, vertical for: – Tubular latches, 60mm backset or longer – NT Falcon Mortice Lock (USA) Example and specification of an order for lever or fixed handles on rose: (example) Handle Style
Rose Type
Handing
Lever (L) or Fixed (F)
Finish
Quantity
PM24
A
LH
L
SCPV
2pr
It is recommended that the lock type is stated when ordering handles. Handle bosses are broached 8.1mm to suit the spindle.
Fixing All roses have tie-screw fixing to suit the latches and locks as detailed. Concealed-fixing on the outside rose, visible-fixing on the inside rose, 5/32” BSW x 3” (76mm) stainless steel screws supplied as standard. Suitable for doors to 60mm thick.
Fixing Centre/Rose Types for Fixed Handles A lock plate is assembled into the rose to prevent the handle from turning. Type A – 50.8mm centres at 45º Type C
– 39.5mm centres vertical
Type I
– 38mm centres, vertical for handles with 57mm diameter roses.
Blank Roses Used for fixing half sets of lever or fixed handles to a door. PM110 External: Universal – Threaded 5/32” BSW at 39.5mm and 50.8mm fixing centres PM111 Internal: Drilled at 39.5mm fixing centres for countersunk screws PM112 Internal: Drilled at 50.8mm fixing centres for countersunk screws
63
28
refer chant™ refer chant™ Product Finishes Technical 4–5 104 – 113
PM110
PM111
PM112
For information on Mason Lever Handles on Plates, refer to pages 106 to 109
Comma PM35 on A3-51 plate
Nile PM25 on A1-21 plate
Rib PM44 on A3-10 plate
29
XX
Mason River PM51 Pull Handle
chant
More about chant™ chant™ is a manufacturer of exclusive hardware for residential, commercial and marine applications. Custom designs, finishes and variations to existing products are also part of the chant™ offering, providing solutions for architects and developers where standard products do not fit on-site requirements. The manufacturing team, artisans in their own right, and the suppliers to the company, all contribute to the creation of these unique products from New Zealand.
32
Our hardware is sought after by architects, developers and owners of exclusive residential and commercial properties and has been the preferred choice of internationally recognised hotels such as the Fairmont in Dubai, Regency Parkway in the Philippines and the Orchard Scott in Singapore. The chant™ products on the folllowing pages are beautifully designed, functional, precision-engineered and very much ‘in touch’ with contemporary architecture and interior design.
33
Bow Pull Handles Bow 501
Bow 503
Bow 502
Bow 504
chant bow
180 200
285 415 530
300 12
400
15
16
18
48
38
65
30
30
56
62
68
74
Bow Lever Handle Bow 511 A3-10
125
Bow 511-S
65
132
Bow 511-F or R
65
145
57
Bow Pull Handles are symmetrical and ‘non’-handed. They are suitable for narrow stile and standard doors. Bow Lever Handle is not handed and is reversible on roses and 44mm wide plates.
145
57
112
34
refer chant™ refer chant™ Product Finishes Escutcheons 4–5 68 – 69
refer Casement refer chant™ Fasteners Technical 88 – 89 104 – 113
Bow 504
Bow 511-F
Bow 502
35
Sabre Pull Handles Sabre 521
Sabre 523
Sabre 522 23
Sabre 524 17
20
14
chant sabre
150 250
280
14
400
433
125
30
50
550
590
17
23
23
70
60
55
Sabre 531-S 60
60
52
53
Sabre Lever Handle Sabre 531 A3-10
43
132
Sabre 531-F or R 60
145
57
Sabre Pull Handles are ‘handed’ and suitable for narrow stile and standard doors. Left hand handles shown. Sabre Lever Handle is not handed and is reversible on roses and 44mm wide plates.
145
57
112
36
refer chant™ refer chant™ Product Finishes Escutcheons 4–5 68 – 69
refer Casement refer chant™ Fasteners Technical 88 – 89 104 – 113
Sabre 524
Sabre 531-F
Sabre 522
37
Arc Pull Handles Arc 541
Arc 543
Arc 542
Arc 544
155 250
chant arc
285
15
400
440
125
27
53
550
590
17
20
20
70
65
Arc 551-S 60
60
60
63
55
Arc Lever Handle Arc 551 A3-10
43
132
Arc 551-F or R 60
145
145
57
Arc Pull Handles are symmetrical and ‘non-handed’. They are suitable for narrow stile and standard doors. Arc Lever Handle is not handed and is reversible on roses and 44mm wide plates.
57
112
38
refer chant™ refer chant™ Product Finishes Escutcheons 4–5 68 – 69
refer Casement refer chant™ Fasteners Technical 88 – 89 104 – 113
Arc 544
Arc 551-F
Arc 542
39
Luna Pull Handles Luna 561
Luna 563
Luna 562
Luna 564
88 rad.
chant luna
180 radius 300 radius
390 radius
500
12
15
95
15
110
65
50
65
57
65
68
Luna Lever Handle Luna 571 A3-10
38
470
580
16
160
250
305
400
125
Luna 571-S
65
132
Luna 571-F or R
65
145
57
Luna Pull Handles are symmetrical and ‘non-handed’. They are suitable for narrow stile and standard doors. Luna Lever Handle is not handed and is reversible on roses and 44mm wide plates.
145
57
112
40
refer chant™ refer chant™ Product Finishes Escutcheons 4–5 68 – 69
refer Casement refer chant™ Fasteners Technical 88 – 89 104 – 113
Luna 564
Luna 571-R
Luna 562
41
chant™ Delta 631 Lever Handle
Cobra Pull Handles Cobra 600
Cobra 601 22
Cobra 602
chant cobra
16
Cobra 603 15
14
200
270 400 565
300
400
40
42
65
70
700
1000
Cobra Pull and Lever Handles are ‘non-handed’. Cobra Lever Handle is reversible on roses and 44mm wide plates. 45
75
Example: Cobra 600 on a 2400mm high door
Cobra 604
Cobra 605 12
14
100
140
125
180
28 60
34 50
55
100
Cobra Door Knocker
Note: One pair of Cobra 600 Pull Handles weigh approximately 16kg. Please ensure the door and structure are sufficently strong to support this added weight.
Cobra 609
Available in standard mounting options. 180
If the Cobra 600 Pull Handles are being used on glass doors, a 12mm hole is required. Mounting bolts are M8 (8mm diameter).
35
Cobra Lever Handles Cobra 610-S 65
Cobra Cabinet Handle
Cobra 611-F
Cobra 611-R
60
60
160
140
Cobra 606
64
100 140 28
57
44
57
Both Cobra 610 and 611 lever handles can accommodate F, R or S rose types
65
35
57
refer chant™ refer chant™ Product Finishes Escutcheons 4–5 68 – 69
refer Casement refer chant™ Fasteners Technical 88 – 89 104 – 113
Cobra 604
Cobra 611-F
Cobra 602
45
Delta Pull and Cabinet Handles Delta 620
Delta 621
Delta 622
Delta 624
Delta 623
Delta 625
chant delta
200 250 300 300
400 450 550
175
200
350
400
45
25 32
32
50
Delta 627
Delta 626
50
* 25 38
1200
58
38
800
58 150
*Offset pillar dimensions. 25mm offset pillars available on 621, 622, 623 and 624 handles
200
125
150
25 45
25
Delta Pull Handles are ‘handed’ left and right, because of their offset asymmetrical triangular form. They are suitable for standard doors and wide stile doors with standard pillars. For narrow stile doors, specify offset pillars to provide finger clearance between the handle and door edge or frame backstop, add sufffix “OS” to the order code.
Example: Delta 620 on a 2400mm high door
38
Non Standard Lengths All Delta pull handles in 25mm, 32mm and 38mm section widths can be produced in the “plated finishes” and PBU to special lengths, in multiples of 100mm. Section width Maximum length 38mm 1200mm 32mm 800mm 25mm 600mm
57
Left hand handles shown. All handles can be produced without the thumb recess if required.
Delta Lever Handle Delta 631 A1-10 51
Delta 631-S 51
142
46
Delta 631-F
153
57
To specify special lengths, state: A: Handle section width 25mm, 32mm or 38mm. B: Overall length. C: Mounting pillar centres. D: Distance from the top of the handle to the top of the thumb recess. E: Length of the thumb recess.(Note:Thumb recess can be deleted). F: Handing: Left-hand (LH) or Right-hand (RH). Example of specification: A
51
153
57 112
45
B
C
Delta 32mm 800mm 600mm /Mounting option/Finish/Quantity
refer chant™ refer chant™ Product Finishes Escutcheons 4–5 68 – 69
D
E
F
125mm
60mm
LH
refer Casement refer chant™ Fasteners Technical 88 – 89 104 – 113
Delta 631 on A1-10 Plate
Delta 623 on standard pillars
Delta 622 on offset pillars
47
Swan 651 Lever Handle
The Swan Lever Handle is a variation of a classic design with simple flowing curves to complement more traditional decor. They are a ‘handed’ handle and are suitable for narrow stile and standard doors.
Refer Groups 10 – 170 Plates on Technical pages 106 to 108. Example shown: Swan 651 A3-111
chant swan
63
125
220
38 (or 32)
Refer Groups 210 – 310 Plates on Technical pages 106 and 109. Example shown: Swan 651 A3-211
63
125
165
44
63
125
Swan 651 on Rose type 38R The following options are detailed on page 105: 38F/38R/38S 41F/41R/41S
57
48
refer chant™ refer chant™ Product Finishes Escutcheons 4–5 68 – 69
refer Casement refer chant™ Fasteners Technical 88 – 89 104 – 113
Swan 651 on A3-211 plate
Swan 651 on 38-R rose
Swan 651 on A3-111 plate
49
Cubic Pull and Cabinet Handles Cubic 661 25 x 12.5mm
Cubic 662 25 x 25mm
Cubic 662 Offset (OS) 25 x 25mm
Cubic 664 16 x 16mm
Cubic 663 19 x 19mm
Cubic 665 12.5 x 12.5mm
chant cubic
centres centres
centres
centres
centres
centres
50 16
52
25
65
25
65
25
19
42 12.5
55
Sizes available (centres specified in mm) Cubic 664: 200/300/450 Cubic 665: 128#/160#/192#/224#/256#/ 300/450
The Cubic Pull Handles are available with offset (OS) pillars for Cubic 661 and 662 Handles (refer example shown above). Cubic Handles are ‘handed’ left and right when fitted with offset pillars. For narrow stile doors, specify offset pillars to provide finger clearance between the handle and door edge or frame backstop, add suffix “OS” to the order code.
A design feature of the Cubic Handles is that they have a square face with a machined, chamfered form inside the handle to provide a comfortable touch.
Cubic Towel Rail Cubic 663 TR (Towel Rail) 19 x 19mm, Y=70 X
centres
Y
Sizes available (centres specified in mm) Cubic 663 TR: 450/600/750 Mounting options: Surface-fixed (SF) or Back-fixed (BF)
Note: – Cubic 664 Pull Handles use M5 mounting studs, the larger sizes use M6 studs. – Cubic Cabinet Handle 665 is back fixed only with M4 screws. – Cubic 663 TR (Towel Rail) mounting options: surface-fixed with 10g screws, or back-fixed with M6 screws. Backplate X = 50 x 50mm – The backplates (X), 50 x 50mm or 38 x 38mm can be used on all pull handles as an added feature if required. Specify ‘BP’ and size with the handle order. – Custom Designs: Cubic Handles with their flat front face lend themselves to custom machining to create special effects and designs. Refer to page 101 for an example. Contact chant™ with your requirements.
Cubic Lever Handles Cubic 671-P only 53
Cubic 672-P 56
145
57
Cubic 672-F 56
145
57
145
57
Cubic 671 Lever Handle: 25 x 12.5mm section Cubic 672 Lever Handle: 19 x 16mm section
50
Both Cubic 671 and 672 can be used with the Pyramid (P) Rose. The Cubic 672 can also be used with the Facet (F) Rose and the Square (S) Rose. Both lever handle styles can be used with any back plates.
#S32 multiples
Sizes available (centres specified in mm) Cubic 661: 300/450/600/800 Cubic 662: 300/450/600/800/1000 Cubic 663: 200/300/450/600
refer chant™ refer chant™ Product Finishes Escutcheons 4–5 68 – 69
refer Casement refer chant™ Fasteners Technical 88 – 89 104 – 113
Cubic 672-P
Cubic 664
Cubic 662
51
Line Pull and Cabinet Handles
chant line
Line 681
Line 682
Line 683
Line 684
centres
centres
centres
centres 12.5
19
42
48
52
Line 691 on Tall Plates Tall Plates can be made to suit the lock types in Groups 20/30/40/50 and 60. *Specify spindle to cylinder barrel centreline or thumb turn dimension, eg. 41+46 – 92mm. To specify: example
52
25
75
Sizes available (centres specified in mm) Line 681: 300/450/600/800 Line 682: 200/300/450/600 Line 683: 128/160/192/224/256/300/450 Line 684: 200/300
Handle Style
Plate Style
Plate Combination
Handing
Lever (L) or Fixed (F)
Finish
Quantity
Line 691
Tall B1
41+46–92*
LH
L
SCPV
2pr
Line 691 on chant™ Tall Plates
100
Line Lever Handles Line 691 on Group 10 Plates 53 135
23
112
*The only handle plate style used with the Line Lever Handle is the B1 plate, 32mm wide on pages 106 and 107. They match the soft edges of the Lever Handle with a complimentary width.
*
90
300
100
32
Line 691 on Group 20/30/40 Plates
X
Overall height X: Group 20: 216mm Group 30: 191mm Group 40: 220mm
Line Door Knocker LIne Door Knocker 689
170
Line 691 on Group 50/60 Plates
X
52
35
30
Overall height X: Group 50: 190mm Group 60: 160mm refer chant™ refer chant™ Product Finishes Escutcheons 4–5 68 – 69
refer Casement refer chant™ Fasteners Technical 88 – 89 104 – 113
Line 684
Line 691 on Tall Plate
Line 683
Line 681
53
chant™ Line 691 Lever Handle on Tall Plate
chant line
Line Door Stop Line Wall Doorstop 3211
Line Floor Doorstop 3212
Line Doorstop 3213
Line Sliding Doorstop 3214
Line Casement 3951
Line Casement 3952
Line 2-Point Lock Lever 3954
Line Escutcheons
56
Oval Cylinder Escutcheon 3440
Emergency Turn / Indicator Escutcheon 3442i
Turn Escutcheon 3441
Profile Cylinder Escutcheon 3443
Emergency Turn Escutcheon 3442
Pull Turn 3444
refer chant™ refer chant™ Product Finishes Escutcheons 4–5 68 – 69
refer Door Stops 73
refer Casement Fasteners 88 – 89
Line 3213
Line 3443
Line 3952
57
Angle Pull and Cabinet Handles Angle 701
Angle 702
Angle 703
Angle Custom
Brass tube or rod is used for electroplated finishes, e.g.: satin chrome plate velvet, polished chrome, black chrome, copper etc.
chant angle
These handle designs are not suitable for production in bronze as the base metal. A
Custom Sizes When custom handles are required, specify: A = Hole centres of pillars B = Diameter of rod C = Height of handle D = Finish
300
450 600
C
B
19
25
50
60
Angle Towel Rail
38
Angle 718 32
25 4
70
80
715: 716: 717: 718:
Angle Lever Handle Angle 711 on Angle/Rod C Rose
Angle 711 A1- 220
20.5 65
65 160
152
1200mm centres 900mm centres 600mm centres 450mm centres
Angle Towel Rail is mounted to the wall with 2 x 8mm mounting screws fastened into a solid timber stud. Recommended minimum framing timber thickness to mount to is 50mm. The washers are required to increase the contact area against the wall and prevent the towel rail from damaging the surface.
57 166
Angle Robe Hook Angle 709 32
Angle/Rod Escutcheons
58
25
70
3450
3451
3452
3452i
3453
3454
Angle Robe Hook is mounted to the wall with an 8mm mounting screw fastened into a solid timber stud. Recommended minimum framing timber thickness to mount to is 50mm.
refer chant™ refer chant™ Product Finishes Escutcheons 4–5 68 – 69
refer Casement refer chant™ Fasteners Technical 88 – 89 104 – 113
Angle 711 on C Rose
Angle 717
Angle 701
59
Rod Pull and Cabinet Handles Rod 721
Rod 722
Materials Brass rod is used for electroplated finishes, e.g.: satin chrome plate velvet, polished chrome plate, black chrome plate, etc.
Rod 723
Bronze rod is used for bronze and “Living Finishes” (refer page 119).
chant rod
400
300
500
600
The rods are machined with the recess for the pillars to fasten into.
200
250
50
22
Tubular handles in 316 grade stainless can be produced for larger sizes. These use an internal nut to fasten the pillars to. Weight and length details need to be considered for shipping, and the practicality of plated finishes for larger handles.
60
25
The Rod Pull and Cabinet Handles can also be made from 316 grade stainless steel, for polished or brushed stainless steel finishes. Specify either finish option. The handles are generally made from solid rod for up to 1000mm in length, and diameters up to 32mm.
Consult chant™ with your requirements.
60
32
B
A
E C
D
Rod Lever Handle Rod 731 on Rod/Angle C Rose
Rod 731 A1- 220
16
16
60
60 150
152
Custom Sizes When custom handles are required, specify: A = Length B = Hole centres of pillars C = Diameter of rod D = Height of handle E = Pillar diameter Standard pillars are 15mm and 19mm diameter (parallel), and 25mm diameter tapered pillars. Other variations can be made to order. F = Number of pillars A central third pillar may be required on extra long handles to avoid the handle flexing. G = Material/Finish
57 166
Rod / Angle Escutcheons
60
3450
3451
3452
3452i
3453
3454
refer chant™ refer chant™ Product Finishes Escutcheons 4–5 68 – 69
refer Casement refer chant™ Fasteners Technical 88 – 89 104 – 113
Rod 731 on Rose
Rod 723
Rod 721
61
Stop 741 Door Knob Diameter 60mm Projection 66mm
Stop Knobs A contemporary and versatile range of door and cabinet knobs suitable for use throughout a project and across a number of applications. The unique sculptured form is available in all finishes.
chant stop
Features
Stop 742 Door Knob Diameter 50mm Projection 63mm
– Finger-recess with a soft contour for user comfort – Internal spring mechanism ensures positive latch and knob return – Large bearing surface provides support for the solid knob machined from brass or bronze – Suitable for long back set tubular latches and mortice locks with 38 or 44mm fixing centres – Knobs are reversible to aid handing and can be turned 90 degrees on the base rose to provide vertical fixing with tubular latches, or horizontal fixing on mortice locks. – Knob fastens to the boss by a socket set-screw on the underside. Removal of the knob allows for tie-screw fixing through the door. – This range of door knobs is complemented by the ‘facet’ range of escutcheons 3410 to 3414 on pages 68 and 69.
Fixing Centres and Latch/ Lock Types Stop 741 Door Knob
Stop 745 Dummy Trim Diameter 60mm Projection 63mm
Fixing Centres: 39.5mm horizontal and vertical and 50.8mm @45 degrees Lock/Latch Types: – chant™ mortice locks – Legge 990 MF Series and Lockwood 3500 Series mortice locks – Profile cylinder mortice locks with nominal 38mm centres and light return springs – Tubular latches – 60mm minimum backset
Stop 742 Door Knob Fixing Centres: 39.5mm horizontal and vertical Lock/Latch Types: – chant™ mortice locks – Legge 990 MF Series mortice locks – Profile cylinder mortice locks with nominal 38mm centres and light return springs – Tubular latches – 60mm minimum backset
Stop 745/746 Dummy Trim A flanged mounting collar is fastened to the door with two screws, the knob attached to the mounting collar with a socket set-screw on the underside. Stop 746 Dummy Trim Diameter 50mm Projection 50mm
62
Stop 751b Cabinet Knob Diameter 35mm Projection 38mm For use with 751 Cabinet Knob on the opposite side of the door. The 751 Knob is fastened to the door with a mounting collar then the 751b Knob is fastened to the collar in the correct alignment. Particularly suitable for shower doors.
Specifying To specify (example) Knob
Finish
Quantity
742
SCPV
2pr
It is recommended that the lock type is stated when ordering knobsets.
chant stop
Stop 751 Cabinet Knob Diameter 35mm Projection 35mm Fixing Screw M5
Stop 752 Cabinet Knob Diameter 28mm Projection 30mm Fixing Screw M5
Stop 753 Cabinet Knob Diameter 22mm Projection 25mm Fixing Screw M5
Cross section of stop knobs showing contoured finger-recess A unique detail off these knobs is that the finger recess is machined in a curved path. This softens the edge at each end providing a comfortable grip. This detail can be applied to custom made knobs of a cylindrical style with a flat or radius end. Contact chant™ to discuss your requirements.
refer chant™ refer chant™ Product Finishes Escutcheons 68 – 69 4–5
refer Door Stops 73
refer chant™ Technical 104 – 113
63
chant round/royal
Round 761 on Mason ‘A’ Rose Knob Diameter 70mm Rose Diameter 63mm Projection 65mm
Round/Royal Knobs Round Door Knobs and matching Escutcheons are designed for front doors and applications where a circular knob is required. This simple, elegant design can be used with a longer backset latch to become a feature of the door. The ability to separate the door knob and latch from the deadbolt and matching escutcheons allows for a variety of combinations to suit individual requirements.
Features Round 762 on Mason ‘A’ Rose Knob Diameter 63mm Rose Diameter 63mm Projection 64mm
– – – – –
Internal spring mechanism ensures positive latch return Large bearing surface provides support for the solid knob Suitable for long back set tubular latches and mortice locks Reversible door knobs aid handing Machined from solid brass or bronze
Fixing Centres and Latch/Lock Types 761/762/763/767 Knobs on Mason ‘A’ Rose Round 763 on Mason ‘A’ Rose Knob Diameter 55mm Rose Diameter 63mm Projection 62mm
Round 762/763 are available on the following chant™ rose types: 38F/38R/38S or 41F/41R/41S F=Facet/R=Radius/S=Square
Round 762 on chant™ 38R Rose Knob Diameter 63mm Rose Diameter 57mm Projection 64mm
Round 763 on chant™ 38R Rose Knob Diameter 55mm Rose Diameter 57mm Projection 62mm 64
Fixing Centres: 50.8mm @ 45 degrees, visible fixing on inside rose Lock/Latch Types: – Tubular latches, 70mm backset or longer – chant™ Mortice Lock, 70mm and 90mm backset With this lock, use Mason PM105, PM108 or chant™ escutcheons
762/763/767 Knobs on chant™ 38F/38R/38S Roses Fixing Centres: 38mm vertical and horizontal, concealed fixing both sides Lock/Latch Types: – Profile cylinder mortice locks with nominal 38mm centres, light return springs and appropriate backset – chant™ Mortice Lock, 70mm and 90mm backset With this lock, use chant™ escutcheons – Tubular latches – 70mm minimum backset recommended
762/763/767 Knobs on chant™ 41F/41R/41S Roses Fixing Centres: 41mm vertical and horizontal, concealed fixing both sides Lock/Latch Types: – chant™ Mortice Lock, 70mm and 90mm backset With this lock, use chant™ escutcheons – Tubular latches – 70mm minimum backset recommended Spindle size: – Spindle supplied: 7.6mm or 8mm – Suitable for full and split spindle applications
Round/Royal Knobs on Plates Refer chant™ Technical, pages 104 – 113, for plate options and information on how to create a specification.
chant round/royal
Round 763 on 44mm Plate Diameter 55mm Plate Width 44mm Projection 63mm Refer chant™ Technical to specify plate type within the following group: Group 210 Example shown: A3–211 Plate
Round 763 on 44mm Plate Diameter 55mm Plate Width 44mm Projection 63mm Refer chant™ Technical to specify plate type within the following groups: Groups 220/230/240/250/310 Example shown: A3–231 Plate
Royal 767 on Mason ‘A’ Rose Door Knob Knob Diameter 55mm Rose Diameter 63mm Projection 62mm
Royal 767 on chant™ 38F/38R/41F/41R Rose Door Knob Knob Diameter 55mm Rose Diameter 57mm Projection 62mm
refer chant™ refer Mason Product Finishes Escutcheons 4–5 26 – 27
refer chant™ Escutcheons 68 – 69
refer chant™ Technical 104 – 113
65
chant round/royal
Royal 767 on 44mm Plate Diameter 55mm Plate Width 44mm Projection 63mm Refer chant™ Technical to specify plate type within the following groups: Groups 210/220/230/240/250 Example shown: B4 220 Plate
Royal 767 on 44mm Plate Diameter 55mm Plate Width 44mm Projection 63mm Example shown: C5 220 Plate
Cylinder Escutcheon A
Tubular Deadbolts and Latches Turn Assembly B
Note Deadbolt Cylinders are 6-pin, C4 profile
Deadbolt Cylinder and Turn – 70mm, 770 includes: – Cylinder Escutcheon A – Turn Assembly B – 60–70mm Backset Deadbolt C
Deadbolt 776 60–70mm C
Deadbolt 777 127mm D
Deadbolt Cylinder and Turn – 127mm, 771 includes: – Cylinder Escutcheon A – Turn Assembly B – 127mm Backset Deadbolt D
Deadbolt Double Cylinder – 70mm, 772 includes: – 2 x Cylinder Escutcheons A – 60–70mm Backset Deadbolt C
Deadbolt Double Cylinder – 127mm, 773 66
includes: – 2 x Cylinder Escutcheons A – 127mm Backset Deadbolt D
Deadbolt Rebate Kit, 774 includes: – Rebate Packer E – Rebate Deadbolt Strike F
chant round/royal
Rebate Packer E
Tubular Latch Rebate Kit, 775 includes: – Rebate Packer E – Rebate Latch Strike G Rebate Deadbolt Strike F
Deadbolt, 776 Adjustable 60-70mm backset
Deadbolt, 777 127mm backset
Tubular Latch, 778 70mm backset Rebate Latch Strike G
Tubular Latch, 779 127mm backset
Product Finishes
Tubular Latch 778 70mm Backset
Finishes Available for Strikes: Stainless Steel SS Bronze Plate* BP Copper Plate COP *This is a brass/bronze plated finish on stainless steel as an approximate match for bronze. Finishes Available for Door Knobs, Cylinder Escutcheon, Turn Assembly and Rebate Packer: refer to Product Finishes page 4 – 5
Tubular Latch 779 127mm Backset
refer chant™ refer Mason Product Finishes Escutcheons 4–5 26 – 27
refer chant™ Escutcheons 68 – 69
refer chant™ Technical 104 – 113
67
chant escutcheons
chant™ Escutcheons Oval Cylinder Escutcheons 3400/3410/3420/3430/3440/3450
Profile Cylinder Escutcheons 3403/3413/3423/3433/3443/3453
Use with Legge 990 MF Series, Lockwood 3500 Series, Astra mortice locks (Australasia), and Union (UK).
Use with all profile cylinder mortice locks.
Maximum door thickness with standard length cylinders 3400/3440/3450 escutcheon 56mm 3410/3420/3430 escutcheon 52mm Fastened with socket set-screw on the underside. To specify:3400/3410/3420/3430/3440/3450/Finish.
Turn Escutcheons 3401/3411/3421/3431/3441/3451
Maximum door thickness 3403/3443/3453 escutcheon 3403/3443/3453 escutcheon 3413/3423/3433 escutcheon 3413/3423/3433 escutcheon
with with with with
5 6 5 6
pin pin pin pin
cylinder cylinder cylinder cylinder
Fastened with socket set screw on the underside. To specify: 3403/3413/3423/3433/3443/3453/Finish
Pull Turns 3404A/3414A/3424A/3434A/3454A
The turn mechanism is fastened to the door with screws, then concealed by either a ‘screw-on’ round style cover or a socket set screw on the underside of the square style covers. Key bars to suit locks as detailed.
For Legge 990 Series mortice locks.
A – 6mm x 2mm bar for Legge 990 MF Series and Lockwood 3500 Series mortice locks. (Australasia) B – 3/16” square spindle for Yale 4600, 8600 and 8700, and Schlage L Series mortice locks (USA) C – 4.5mm square spindle These spindles have a 2mm D – 7.0mm square spindle flat extension bar when E – 7.6mm square spindle ordered with Emergency F – 8.0mm square spindle Turns. Add suffix ET to order G – 5.0mm square spindle code eg. To specify: H – 6.0mm square spindle 3401F/Finish/ET J – 3/16” square spindle on the diamond ( ) for Accurate Locks (USA) K – 10mm x 3mm recess to suit chant™ Profile Cylinder Turn Adaptor 1241 etc. To specify: 3401/3411/3421/3431/3441/3451/ A, B, etc./Finish
Pull Turns are fitted to the inside of entrance doors to withdraw the latch bolt, when key entry is used on the outside. The turn base is securely fastened to an adaptor plate which is fixed to the side of the lock case prior to installation in the door. Depending on the lock used, specify the spindle bar type required from the chart opposite for turn escutcheons: typically A, E or F. Note: the 3444 Pull Turn can not be used with the adapter plate because of its narrow body. It is fastened instead with four woodscrews to the surface of the door. Refer to page 113 for an exploded view of the fastening of the Pull Turn to the lock. To specify: 3404A or B/3414A or B/3424A or B/ 3434A or B/3444A or B/3454A or B/Spindle Type/Finish
Pull Turns 3404B/3414B/3424B/3434B/3454B For SAB profile cylinder mortice locks.
Escutcheon Dimensions Diameter or square
Emergency Turn Escutcheons 3402/3412/3422/3432/3442/3452
50mm
Line range
32 x 50mm
The turn mechanism is fastened to the door with screws, then concealed by either a ‘screw-on’ round style cover or a socket set-screw on the underside of the square style covers. Turn operated by the key bar on 3401/3411/3421/3431/ 3441/3451 Turn Escutcheon above. To specify: 3402/3412/3422/3432/3442/3452/Finish
3400/3403/3440/3443/3450/3453 Cylinder escutcheon projection
7mm
3410/3413/3420/3423/3430/3433 Cylinder escutcheon projection
9mm
3401/3411/3421/3431/3441/3451 Turn escutcheon projection
30mm
Emergency Turn / Indicator Escutcheons 3402i/3412i/3422i/3432i/3442i/3452i
3404/3414/3424/3434/3444/3454 Pull/Turn escutcheon projection
48mm
The turn mechanism is fastened to the door with screws, then concealed by either a ‘screw-on’ round style cover or a socket set-screw on the underside of the square style covers. Turn operated by key bar on 3401/3411/3421/3431 Turn Escutcheon above. Red and green colour indicator behind the turn button shows the lock status. To specify: 3402i/3412i/3422i/3432i/3442i/3452i/ Finish
68
46mm 54mm 42mm 50mm
Non-standard Escutcheons Custom shaped escutcheons can be produced to order.
refer chant™ refer chant™ Product Finishes Mortice Locks XX 90 – 97
refer chant™ Technical 104 – 113
refer fitting of Pull Turns 113
Radius
Facet
Square
Pyramid
Line
Angle/Rod
3400
3410
3420
3430
3440
3450
3401
3411
3421
3431
3441
3451
3402
3412
3422
3432
3442
3452
3402i
3412i
3422i
3432i
3442i
3452i
3403
3413
3423
3433
3443
3453
3404
3414
3424
3434
3444
3454
Mason Rib PM42 Pull Handle
accessories
72
Door Stops Wall Door Stop 3201
Hold Back 3220
Diameter at base Projection
Installed length
25mm 75mm
The hook bar has an integral rubber door stop and a nylon anti-rattle catch mechanism.
The mounting collar is fastened to the wall with an 8 gauge screw. The Door Stop is fastened to the collar with 2 x socket set-screws.
Pedestal Hold Back 3222
Floor Door Stop 3202 Diameter Projection
80mm
Height
38mm 35mm
162mm
Fastened to the floor with 3 x woodscrews or, 3 x 6.0 or 6.5mm countersunk masonry anchors.
Fastened to the floor with 2 x woodscrews or, 2 x 6.0 or 6.5mm countersunk masonry anchors. The rubber insert is fastened by a hex socket screw from the rear.
accessories door stops/ hold backs
Hold Backs
Floor Door Stop 3203 with 15mm Extension Diameter 42mm Projection 50mm Fastened to the floor with 2 x woodscrews or, 2 x 6.0 or 6.5mm countersunk masonry anchors. The rubber insert is fastened by a hex socket screw from the rear.
Line Door Stop Wall Door Stop 3211 Square Projection
22mm 75mm
The mounting collar is fastened to the wall with an 8 gauge screw. The Door Stop is fastened to the collar with 2 x socket set-screws.
Floor Door Stop 3212 Square Projection
32mm 35mm
Fastened to the floor with 2 x woodscrews or, 2 x 6.0 or 6.5mm countersunk masonry anchors. The rubber insert is fastened by hex socket screw from the rear.
Floor Door Stop 3213 Square Projection
32mm 50mm
Fastened to the floor with 2 x woodscrews or, 2 x 6.0 or 6.5mm countersunk masonry anchors. Rubber insert fastened by hex socket screw from the rear.
Sliding Door Stop 3214 Rectangular Length
15 x 32mm 40mm
The mounting base is fastened to the door with 4 x 8g screws. Door Stop clips onto the base.
refer chant™ refer Product Finishes chant™ Line 4–5 52 – 57
refer chant™ Stop 62 – 63
73
accessories push plates
Push Plates This range of plates can be used with chant™ door hardware to complement lever handle back plate styles. Standard plates measure 75mm x 250mm x 3mm thick. The thickness allows radiused and chamfered edges from groups B and C, page 106, to be provided.
A1
A2
A3
A4
A5
Style Option and Code Number 1 2 75 x 250 “A” 3501 3502 75 x 250 “B” 3511 3512 75 x 250 “C” 3521 3522
3 3503 3513 3523
4 3504 3514 3524
5 3505 3515 3525
Fixing Options: X Glue fix Y Countersunk screw Z As a back plate behind a pull handle. The pull handle style, hole centres and hole size need to be specified. To order specify: (example) B1
B2
B3
B4
B5 Code Number
Fixing Option
Finish
Quantity
A1
Y
PBZ
2
Custom Sizes Please note that special sizes of backplates can be made to order, please contact chant™.
C1
74
C2
C3
C4
C5
refer chant™ refer Mason refer chant™ Product Finishes Lever Handles Technical 4–5 28 – 29 104 – 113
Pull Handle Back Plates Pull Handle Back Plates and Strengthening Plates. This product is custom designed for applications where back to back fixing is required, and the ability to provide strengthening on a narrow stile timber door when a mortice lock is fitted. These plates are made from 6.4mm thick brass bar. The outside plate has threaded studs on its back side, with tie-screws coming through from the inside plate to clamp them onto the door. Edge detail as per push plate and lever handle backplate options. If pull handles are being fitted, the handle style, hole centres and hole size need to be specified.
pull handle accessories push plates back plates
Pull Handle Back Plate 3600, Example A
Special sizes of plates to suit particular mortice locks may be required to allow space for the lock to fit between the tie-screws on the top or the bottom half of the plate.
Pull Handle Back Plate Example B
Plates can be made with pull handles on one or both sides, and options of double cylinder, cylinder and turn, or chant™ Cylinder/Turn Adapter (refer to page 100) Custom sizes of plates tailoring individual requirements are generally widths from 50mm to 75mm and lengths to 300mm. Specify: – plate size – lock type – handle style and size – fixing centres – fixing bolt size of the pull handle – sketch or drawing of the proposed assembly
75
accessories flush pulls
Style 1
Style 2
Style 3
Flush Pulls These Flush Pulls are designed with full machine radiused, internal edges for a soft touch, and with styles to compliment other chant™ products. The various sizes and styles allow the pulls to be used in many design concepts and situations.
Features: –
– (example: 1441)
(1442)
(1443)
Style 5
Mounting blocks for concealed fixing
– Style 4
– –
Machine radiused edges with an enlarged internal recess for a soft touch, and a 2mm face flange for minimal projection off the door surface. Manufactured from brass for polished brass and electroplated finishes, bronze for polished bronze and aged bronze finishes Two piece construction allows for fully machined and finished surfaces. Internal finger depth 12.5mm Concealed-fixing options as below.
Fixing Options: A. Concealed-fixing for aluminium doors: The stile requires a machined opening to insert the Flush Pull into. Then insert the Flush Pull into the aluminium extrusion, and fasten the socket set-screw to lock the Flush Pull in place. B. Concealed-fixing for wooden doors: The door requires a routed recess to accept mounting blocks, top and bottom, screwed into place. Insert the Flush Pull and fasten the socket set-screw to lock the Flush Pull in place. (1444)
(1445)
Style Options: 1 2
3
4
5
Installation: Precise machining of the recess in aluminium and wooden doors for option A and B is required. For best results, it is recommended that a chant™ Routing Jig is used, with appropriate template guide, or a custom made routing template. Flush Pulls with fixing option A are also suitable for glue fixing.
Flush Pull Sizes and Code Numbers: Overall Size
Finger Recess
Style Option and Code Number 1 2 3 4 5
38 38 38 38 50 50 50 50
20 20 20 20 30 30 30 30
1401 1411 1421 1431 1441 1451 1461 1471
x x x x x x x x
100 150 200 250 150 175 200 250
x x x x x x x x
60 110 160 210 110 135 160 210
1402 1412 1422 1432 1442 1452 1462 1472
1403 1413 1423 1433 1443 1453 1463 1473
1404 1414 1424 1434 1444 1454 1464 1474
To order specify: (example)
76
To assist with installation, refer Routing Jig 6043, page 117
Code Number
Fixing Option
Finish
1431
A
SCPV
1405 1415 1425 1435 1445 1455 1465 1475
Recessed Pull 1501
Recessed Pull 1502
Recessed Pulls Designed to be fitted to the edge of sliding doors or to the face of swinging doors. 1500 – 1505 have a body 25 x 85mm and are conceal-fixed with 3 styles available. The 1506 – 1508 are 25 x 110mm and are visible-fixed.
Recessed Pull 1500 4.75 mm radiused corners – flush fitted. Prepare recess with a 9.5 mm (3/8) diameter router cutter using a pilot guide and chant™ Routing Jig; refer to page 117. Recessed Pull 1503
Recessed Pull 1504
Recessed Pull 1505
Recessed Pull 1501 Square corners – flush fitted. Machine recess as for 1500 above with 9.5mm router cutter, then chisel the corners square. Use this style when being fitted with chant™ Sliding Door Privacy Flush Pull (the lock has a square cornered face plate to match).
accessories recessed pulls
Recessed Pull 1500
Recessed Pull 1502 12.5mm radiused ends. Installation as for 1500 above.
Recessed Pull 1503/1504/1505
Recessed Pull 1506
Recessed Pull 1507
Recessed Pull 1508
2mm face flange. Radius corners/square corners/radiused end with rebate. These Recessed Pulls have a rebated body and 2mm thick face flange. Allows for more tolerance with the preparation of the recess in the door to accept the Recessed Pull.
Recessed Pull 1506/1507/1508 Radiused corners/square corners/radiused end with 3mm face flange and visible -fixing for fastening into aluminium door stiles.
Sliding Door Hand Pull 1510 This is designed to be morticed into the edge of heavy sliding doors when a full hand grip is required. The handle ejects from the flush position with spring pressure, by being pushed in to release the catch mechanism holding it in. To store the handle, push it in to catch when flush. 105 25
70
Sliding Door Hand Pull 1510
210 180 115
To assist with installation of Recessed Pulls, refer to Routing Jig 6045, page 117 For Sliding Hand Pull, refer to Lock Morticing Machine 6005 and Faceplate Routing Jig 6010, pages 115 – 116
77
accessories privacy flush pulls
Style 1
Style 2
Style 3
Privacy Flush Pulls Designed to fit back to back on sliding doors of minimum thickness 35mm. The lock is sandwiched between the Pulls while the Pulls are fastened back to back with visible-fixing on the inside Pull. The backset of the Flush Pull centerline is 50mm. Door thickness must be specified so that the correct length screws and spindle can be provided.
(example 1601)
(1602)
Style 4
Style 5
(1603)
The P ulls are available in the following configurations: – Turn and Emergency TE – Turn and Turn TT Style Options: 1 2
3
4
5
Privacy Flush Pulls and Code Numbers
(1604)
(1605)
Privacy Flush Pull 1601TE
Overall Size
Finger Recess
Style Option and Code Number 1 2 3 4 5
50 50 50 50
30 30 30 30
1601 1611 1621 1631
x x x x
150 175 200 250
x x x x
110 135 160 210
1602 1612 1622 1632
1603 1613 1623 1633
1604 1614 1624 1634
1605 1615 1625 1635
To order specify: (example)
78
To assist with installation, refer Routing Jig 6043 and 6045, page 117
Code Number
Turn Option
Finish
Door Thickness
1611
TE
SCPV
40mm
Designed to fit back to back on sliding doors of minimum thickness 38mm. The flange thickness is 2mm making an overall thickness of 42mm. The backset of the Flush Pull centrelines are 50mm or 35mm. Door thickness must be specified so that the correct length screws and spindle can be provided. The lock is a 3-Pin Profile Cylinder (C4 Key Profile) and is 42mm long. This puts the cylinder flush with the surface of the Pull. On the single cylinder version, the rear of the cylinder protrudes into the Flush Pull on the opposite side on doors thinner than 42mm.
accessories locking flush pulls
Locking Flush Pulls
Locking Flush Pull 1711, with Strike, 50mm backset
The single thumb turn lock requires a minimum door thickness of 42mm.
Locking Flush Pull 1811, with Strike, 35mm backset Optional Strike 1899
The 35mm backset Locking Flush Pull has a case depth of 50mm and is designed for aluminium sliding doors. The faceplate is 3mm thick. The Optional Strike 1899, measures 124mm x 19mm, and is adjustable from 15mm to 20mm high.
Locking Flush Pulls and Code Numbers - 50mm backset Overall Size
Custom Variations Custom variations of Lock and Flush Pull assemblies, particularly those requiring a thumb turn on the inside, can be produced to suit proprietary aluminium stiles. Contact chant™ to discuss your requirements.
Style Options: 1 2
3
4
5
Finger Recess
Style Option and Code Number 1 2 3 4 5
Single Cylinder 50 x 175 30 x 135 1711 1712 50 x 200 30 x 160 1721 1722 50 x 250 30 x 210 1731 1732
1713 1723 1733
1714 1724 1734
1715 1725 1735
Double Cylinder 50 x 175 30 x 135 1741 1742 50 x 200 30 x 160 1751 1752 50 x 250 30 x 210 1761 1762
1743 1753 1763
1744 1754 1764
1745 1755 1765
Thumb Turn (inside only) 50 x 175 30 x 135 1771 1772 50 x 200 30 x 160 1781 1782 50 x 250 30 x 210 1791 1792
1773 1783 1793
1774 1784 1794
1775 1785 1795
Locking Flush Pulls and Code Numbers – 35mm backset Overall Size
To assist with installation, refer Routing Jigs 6043, 6045 and Lock Morticing Machine 6005, pages 115 –117
Finger Recess
Style Option and Code Number 1 2 3 4 5
Single Cylinder 38 x 175 30 x 135 1811 1812 38 x 200 30 x 160 1821 1822 38 x 250 30 x 210 1831 1832
1813 1823 1833
1814 1824 1834
1815 1825 1835
Double Cylinder 38 x 175 20 x 135 1841 1842 38 x 200 20 x 160 1851 1852 38 x 250 20 x 210 1861 1862
1843 1853 1863
1844 1854 1864
1845 1855 1865
79
accessories XXXX flush sliding bolts
Flush Sliding Bolts/Conceal-fixed Sliding Flush Bolts This range of Sliding Flush Bolts is designed for use on conventional doors, bifold, sliding and aluminium stile doors. The design of the body has a 2mm thick face flange for minimal projection off the door surface. They can be fitted fully flush with careful recess preparation into wood doors if required. The standard Conceal-fixed Flush Bolts are fitted flush to the door edge on wood and aluminium doors. Mounting blocks are fitted into the recess on wooden doors to fasten the flush bolt to, and a machined opening in aluminium stiles will accept the Flush Bolt. Fastening is by semi-concealed socket set-screw. The body sizes are: – 50mm wide x 200 long - 20mm bolt projection; – 50mm wide x 220 long - 40mm bolt projection. The standard Flush Bolts have a 5mm x 15mm flat bolt. Extensions available: 0mm, 100mm, 200mm, 300mm. Extension rod is M8 Flat Strike
Extended Sliding Bolts The Extended Conceal-fixed Flush Bolts are fitted into their appropriate recess, 40mm wide x 12.5mm deep, away from the door edge. The bolt size is 16mm diameter machined with flats to 12.7mm across, with extensions of 0mm, 100mm, 200mm and 300mm from the door edge. Extension rod is M8.
Flat Strike
Waterproof Strike
Waterproof Strike
Sliding Bolt Offsets A B
C
Recess size in wood doors: 40mm wide x 12.5mm deep with special lengths to suit the different types and lengths of bolts.
The offset of the 12.7mm bolt centreline, from the door surface on wood doors is 18mm; aluminium doors, 20mm; and aluminium doors with timber facings, 34mm. Aluminium industry, standard rod sets for extended bolts can be used. Special offsets for thick doors and custom applications can be produced to order.
D
For wooden doors, where extended bolts are required; a drill jig is available from chant™ to accurately drill the extension rod hole into the stile. Particularly useful for 200mm and 300mm versions. Extension lengths are 100mm, 200mm, and 300mm from the door edge. Refer to Jig 6046, page 117. Locking Versions All bolts are lockable with a Key Insert Lock 2899. Refer page 82.
10.5
5.5
Style Options: Extended Bolts 1 2 3
Min. 20
4
Style Options: Flush with the bottom of the door 1 2 3 4
80
Min. 15
5
5
Mounting Options and Offsets Options A to D cover some alternatives for sliding doors and the position of the bolt. Considerations needs to be made for the: – thickness of the door – type of guide track and its width; hence, available space for the strike and its function. Example A 10.5mm from the face of the door to the back of the 5mm bolt. Example B 5.5mm from the face of the door to the back of the 5mm bolt and is for sliding doors only. Example C Extended bolt “zero”, fitted flush to the edge of the door. Used where the bolt needs to located into the middle of the door guide track. Example D Extended bolt, away from the edge of the door. Allowance needs to be made for the offsets when the bolts are flush fitted to the surface of the doors, plus 2mm. The above options A, C, D can be used on opening doors depending on: – the relationship between the door and the sill, or head – suitable mounting of the strike
2011
2021
2111
2121
Flush Sliding Bolts – Code Numbers for 20mm Throw Bolts Style Option and Code Number 1 2 3 4 5
200
220
240
20 40
2041
2131
200
2031 2032 2033 2034 2035 2041 2042 2043 2044 2045
extension length
20
Style Option and Code Number 1 2 3 4 5
2141
220
extension length
240
Strikes: Flat/Standard Bolt 2090
2111 2112 2113 2114 2115 2121 2122 2123 2124 2125 2131 2132 2133 2134 2135 2141 2142 2143 2144 2145
Code Number
Offset Dimension
Extension Length
Strike Type
Finish
2011 2111
10.5mm 18mm
– 200mm
2090 2190
SCPV PBZ
Strikes:
Extended Bolt 2190 15 25
50
Conceal-fixed, Standard 50 x 220 Non Locking 50 x 240 Locking Conceal-fixed, Extended 50 x 220 Non Locking 50 x 240 Locking
To order specify: (examples) extension length 40
Flat Strike 3mm thick – opening door
2011 2012 2013 2014 2015 2021 2022 2023 2024 2025
Sliding Flush Bolts – Code Numbers for 40mm Throw Bolts
Flush Sliding Bolt – 12.7mm Bolt Extended 0,100, 200, 300mm 2031
Conceal-fixed, Standard 50 x 200 Non Locking 50 x 200 Locking Conceal-fixed, Extended 50 x 200 Non Locking 50 x 200 Locking
accessories flush sliding bolts
Flush Sliding Bolts/Conceal-fixed
Flush Sliding Bolt/Standard, 15 x 5mm flat bolt (2111/2121 are suitable for sliding doors only)
There are various options available to suit specific site requirements. The strikes are designed with over-length slots for opening doors, and over-width slots for sliding doors. This provides restricted movement of the bolt and door in the correct direction. All flat strikes are 3mm thick.
2091
2191
Flat Strike 3mm thick – sliding door
25
2092 Flat Strike 3mm thick – sliding door open sided
2093
2193
Waterproof Strike – opening door
19
2094 Waterproof Strike – sliding door
2194 25
To assist with installation, refer Flush Bolt Jig 6043, 6044, pages 117
81
accessories flush sliding bolts
Flush Sliding Bolt 2201/2301
Flush Sliding Bolts/Visible-fixed These bolts are for situations where there is restricted height for the concealed mounting versions. Offsets are as shown on page 80 – Sliding Bolt Offsets A – 10.5mm B – 5.5mm Strike options as detailed previously, page 81
Sliding Flush Bolt – 20mm Throw Visible-fixed 55 x 100: 2201
Sliding Flush Bolt – 40mm Throw Visible-fixed 55 x 140: 2301 To order specify: (examples) Code Number
Offset Dimension
Strike Type
Finish
2201 2301
5.5mm 5mm
2092 2091
SCPV PBZ
Please contact chant™ if you have a requirement for custom variations of these Flush Sliding Bolts.
Key Insert Lock 2899 Insert position
Lock position
Retract key, insert remains
82
Key Insert Lock Our Key Insert Lock is used to lock the bolts on our Flush Sliding Bolts and Square Bolts. The ‘insert’ part of the lock which is attached to the key, is inserted into the bolt to be locked, the key rotated 90˚ and then withdrawn. The bolt is then prevented from operating. To unlock, insert the key, rotate and remove the insert. This is a practical alternative to wafer locks that can be easily forced and cannot be master-keyed; or much larger locks that may be master-keyed, but interfere with the door structure.
Designed for use on wood or aluminium sliding doors as a combination Flush Bolt and Flush Pull where the combined function minimises components on the door. The concealed fixing is the same as standard Flush Sliding Bolts. Allowance needs to be made for the offsets when the bolts are flush fitted to the surface of the doors, plus 2mm.
Flush Pull/Bolt/Conceal-fixed – Code Numbers for 20mm Throw Bolts Style Option and Code Number 1 2 3 4 5 Conceal-fixed, Extended 50 x 220 Non Locking 2431 2432 2433 2434 2435
accessories flush pull bolts
Flush Pull Bolts/Conceal-fixed
Flush Pull Bolt 2531
Flush Pull Bolt 2431
Flush Pull/Bolt/Conceal-fixed – Code Numbers for 40mm Throw Bolts Style Option and Code Number 1 2 3 4 5 Conceal-fixed, Extended 50 x 260 Non Locking 2531 2532 2533 2534 2535 To order specify: (example) Code Number
Offset Dimension
Extension Length
Strike Type
Finish
2431
18mm
1000mm
2190
SCPV
When these bolts are fitted to wooden doors, the door must be custom built, as the stile requires a trench, vertically positioned to allow the bolt to operate. The position of the trench will depend on the operation of the door, opening or sliding and the construction of the door, particularly in relation to tennon joints in the corners. On a sliding door, consideration will need to be made in relation to the track, bolt position, and space for the strike.
Flush Pull Bolt – 12.7mm Bolt Extended as required 2431 2531
Option A: Split stile, trenched before the two sections are glued together. Alternative join line shown as dotted line.
220
260
Option B: Trenched from the edge and back-filled with an insert.
extension length 20
extension length 40
Style Options: Extended Bolts 1 2 3
4
5
Option C: Trenched from the front face and back filled with an insert.
83
accessories square bolts
Socket Bolt 2810
Socket Bolt shown in the edge of the door Also suitable for fitting into a rebated door and to the face of the door
Square Bolts This unique range of bolts with clean simple lines are extremely versatile in their operating functions. The bolts can be surface or flush mounted on the face or edge of a door, or fitted into the rebate of the inactive leaf of a pair of doors. A generous and accessible finger recess makes them practical to use. The surface mounted bolts can be machined with a 2mm radius to match the Line door handles range.
‘Necked’ Bolt 2840 ‘Necked’ Bolt shown on the face of the door
Uses: – For securing standard doors by the socket bolt at the bottom and the spring bolt at the top. – Securing the inactive leaf on a pair of doors when fitted into the rebate. Avoids the need for locking bolts on the face of the door. – Self latching at the top of a bifold door with a socket bolt at the bottom. – Positive latching at the top of a door leading to a swimming pool.
Socket Bolt 12.7mm diameter bolt x 20mm throw.
“Necked” Bolt Although not a true necked bolt, it serves the same function. The bolt has a flat on it which allows the strike to be flush to the edge of a door sill.
Spring Bolt 14mm diameter bolt with a flat face for latching into the strike. Spring Bolt 2850
Spring Bolt shown fitted into a rebated door. Rebate preparation is shown on the operating leaf to clear the Spring Bolt
The Spring and “Necked” Bolts are reversible onsite if necessary.
Mounting The bolts are secured to the door by two 12 gauge x 50mm countersunk, square drive stainless steel screws on the 150mm and 300mm bolts. The 450mm and 600mm bolts have 3 screws.
Locking The Socket and Necked Bolt can be locked with a Key Insert Lock 2899. Refer to page 82.
Size The body of all bolts is 19mm square.
Surface Strike for Socket Bolt 2890
Surface Strike for Spring Bolt 2891
45
45
Flat Strike for ‘Necked’ Bolt 2893
84
19
Surface In-line Strike for Socket Bolt 2892
50
Flat Strike for Spring Bolt 2894
To order specify: (example) Code Number
Strike Number
Finish
2810
2890
SCPV
Square Bolts Code Numbers
Clearance to allow free movement in a recesssed installation where the slot is 19mm wide
(viewed from the bolt end of the square bolt)
Socket Bolts
accessories square bolts
Clearance to prevent scratching of the door surface
Mounting options on standard doors
40
Mounting options on rebated doors
length
Code numbers based on length in mm 150 200 300 Socket Bolt 2810 2811 2812 Socket Bolt Locking 2820 2821 2822
450 2813 2823
600 2814 2824
450 2833 2843
600 2834 2844
‘Necked’ Bolt
Example of necked bolt
Example of locking socket bolt
Example of standard socket bolt
direction of door closing
Code numbers based on length in mm 150 200 300 ‘Necked’ Bolt 2830 2831 2832 ‘Necked’ Bolt Locking 2840 2841 2842
Spring Bolts 2850 –
2860 –
2870 –
2880 –
direction of door closing
reversible on site
reversible on site
Code numbers based on length in mm 150 200 300 2850 2851 2852
450 2853
600 2854
2860
2861
2862
2863
2864
2870
2871
2872
2873
2874
2880
2881
2882
2883
2884 85
Hinge 100 x 75mm
Hinge 100 x 75mm with handle
Hinges
accessories hinges
This range of Hinges, made from bronze as the base metal, are designed for doors and applications where a substantial hinge is required and are finished primarily in the bronze finishes. The Hinges feature a nine knuckle design, providing four load bearing faces per hinge, with a 316 stainless steel hinge pin. Screw hole patterns can be positioned to suit individual requirements. Hinge 100 x 75mm with ball tips
Hinge Dimensions Height Leaf Thickness Overall Thickness Widths
100mm 5mm 11mm 75mm/100mm/120mm/200mm
Special hinge widths from 120mm to 200mm can be produced to order.
Sizes and Code Numbers
Hinge 100 x 100mm
100 100 100 100
x x x x
75mm 100mm 120mm 200mm
Plain Hinge Fixed Pin
Ball Tip
3701 3711 3721 3731
3703 3713 3723 3733
3702 3712 3722 3732
Finishes Available Polished Bronze Satin Bronze Aged Sand Bronze Aged Weathered Bronze
PBZ SBZA SABA WBZ
To order, specify: (example)
Hinge 100 x 120mm
Hinge 100 x 200mm
86
Code Number
Finish
3701
PBZ
Radiused (R) Rose shown
Handrail Support 3801, 3802, 3811 and 3812 are designed to follow the styling of the roses on our door handle ranges with matching rose covers. Available in Facet (F), Radius (R), Square (S) and Cylinder (C) styles.
50
70
The rose cover clips over the base to provide a concealed fixing. The handrail bracket on the wall mounted version can be rotated on the base to allow best alignment of the four screws that fasten it to the wall studs. 57
76
Handrail Supports
Handrail Support – screw fixed 3811 for flat rail/3812 for round rail
Handrail support 3821 and 3822 screw onto an M12 x 75mm stud that is screwed into the timber wall for a secure fixing. The 38mm washer provides added protection of the wall surface when the bracket screws onto the stud. Radiused (R) Rose shown
accessories handrail supports
Handrail Support – screw fixed 3801 for flat rail/3802 for round rail
Handrail Support 3831 and 3832 are for through-bolt fixing to a glass or wooden wall with an M12 countersunk hex-drive screw. Specify the wall thickness. All support brackets are made from brass for the electroplated finishes and bronze for the bronze finishes. To order, specify: (example)
70
Code Number
Rose Type (where applicable)
Finish
3801
R
SCPV
57
Handrail Support – stud mounted 3821 for flat rail/3822 for round rail
70
76
38
Glass panel mounted 3831 for flat rail/3832 for round rail
87
Comma 3901
Comma 3902
Comma 3904
accessories casement fasteners
2 Point Lock Lever
Casement Fasteners Designed for wood and aluminium windows. The lever style options complement various ranges of lever handles. Base plate styles are based on the Line range and a tapered style. The Casement Fasteners have a semi-concealed fixing for both the lever and the strike.
Sabre 3911
The Mortice Strike, at right angles to the Fastener; has a nylon insert to avoid metal to metal contact with the locking pin.
Sabre 3912
Handing of Casement Fasteners The Casement Fasteners shown are all Left Hand (LH). Specify Left Hand (LH) or Right hand (RH). The Wedge Strike is either flush or offset 6mm.
Casement Fasteners and Code Numbers Cobra 3921
Delta 3931
Cobra 3922
Comma Sabre Cobra Delta Swan Line Angle Rod
Delta 3932
With Mortice Strike
With Wedge Strike (flush)
With Wedge Strike (6mm offset)
2 Point Lock Lever
3901 3911 3921 3931 3941 3951 3961 3971
3902 3912 3922 3932 3942 3952 3962 3972
3903 3913 3923 3933 3943 3953 3963 3973
3904 – – – – 3954 – 3974
To order specify; (example)
Swan 3941
Swan 3942
Line 3951
Line 3952
Line 3954 2 Point Lock Lever
88
Code number
Handing
Base Plate Style
Finish
3901
LH
Tapered or Line
SCPV
Angle 3961
Dimensions
Angle 3962
Line 3952 example shown
With Wedge Strike
16 21
64
6
21
21
X1
With Mortice Strike Rod 3971
Rod 3972
Rod 3974 32
2 Point Lock Lever
21
accessories casement fasteners
Y1 9
Line 3953 example shown Y2
41 60
Mortice Strike – Flush Mounted 3995
When the Casement Strike needs to be flush mounted, specify Mortice Strike 3995 above. It is visible-fixed and has a nylon insert to avoid metal to metal contact with the locking pin.
fixing centres X2
Dimensions overall (mm) casement fastener length height X1 Y1 Comma 125 47 Sabre 125 47 Cobra 120 47 Delta 120 38 Swan 120 47 Line 120 38 Angle 120 38 Rod 120 38
2 point lock lever length height X2 Y2 120 22 – – – – – – – – 126 20 – – 114 22
Telescopic/Security Stay The Telescopic/Security Stays have a semi-concealed fixing at each end. The thumb turn operates onto a clutch ring which grips the extension rod for a positive lock.
Security Stay 3998
The Telescopic Stay travel is 130mm. The Security Stay travel is limited to 55mm, to limit the window opening. This needs to be positioned so that at its full extension, the window opening is limited to 100mm; as required by some local body bylaws for upper storey windows.
53
Telescopic Stay 3999 38
closed X / open Y
Security Stay 100mm extension: X = 120 / Y = 180 Telescopic Stay 175mm extension: X = 195 / Y = 330
40
89
accessories mortice locks & latches
This extensive series of locks and latches have been developed to cover many options and combinations of lock and door types, the use of small, medium, large and tall pull handles and lever handles.
Features of Our Locks and Latches – –
– – –
Designed to marry with our extensive range of pull handles, lever handles, escutcheons and accessory components. The lock faceplates are made from 316 stainless steel and the cases from 304 stainless steel. Internal components are from brass and stainless steel. All strikes are made from 316 stainless steel. Strike packers made from aluminium extrusion and are natural anodized. All locks are operated by standard profile cylinders and turns, or our chant™ Profile Cylinder Turn Adaptor or Cam Adaptor.
Handing of Locks and Latches (where applicable) The way we hand our locks, is to marry them with the strikes, A or B. Refer Handing of Strikes diagram with lock details, page 95. The locks and latches can be handed on site, however, many of our strikes are handed. Order carefully and/or hang doors as planned. – “A” strikes and locks, as viewed from the outside: – suit locks on the left, doors opening out – or locks on the right, doors opening in – “B” strikes and locks, as viewed from the outside: – suit locks on the right, doors opening out – or locks on the left, doors opening in
Matching Locks, Handles, and Door Types General considerations: – Co-ordinate the escutcheon style to the handle style – Choose the lock type for the operating function required – The backset is the distance from the faceplate or the edge of the door to the cylinder barrel centre line, and/or lever handle spindle. – Stile: the vertical member of the edge of a door, typically: – the aluminum section of an aluminum/glass door – the vertical timber member of a timber/glass door – the vertical timber member of a timber door with a panel of horizontal or vertical tongue and groove boards. The ‘boards’ may be genuine, or created by grooves in the surface of a solid door. Examples showing typical combinations of pull handles and locks on doors:
1
Long curved handle to span lock providing knuckle room. Night latch or roller lock with 45 or 60mm backset of lock.
2
Small curved handle above or below lock on narrow stile doors. Mounting pillars of handle in line with the lock cylinder, or handle visually centred on the centre line of cylinder. Lock backset may suit the centre line of the stile.
Lock Functions Mortice Locks 1000 – 1004: Used with lever handles to withdraw the latch. A key can then be used on both sides or alternatively; a key on the outside with a thumb turn on the inside to lock and unlock the bolt.
3
Mortice Night Latches 1021 – 1023: Key entry to withdraw the latch bolt, key or thumb turn to exit. When the door is shut, it is locked. Using the hold back function, the door is free to swing, or can be held shut (but not locked) with a door closer or roller latch. Use pull handles both sides and a thumb turn inside, or pull turn on the inside instead of a pull handle. Dead locking function is included in the lock. Mortice Deadbolts 1030 – 1033: Used where a latching function is not required. Fit the cylinder/thumb turn combination to suit. The door must be pushed shut, then locked with key or thumb turn. Mortice Sliding Door Locks 1040 – 1042: Fit the cylinder/thumb turn combination to suit. Mortice Roller Locks 1051 – 1054: Key on both sides, or key on the outside and thumb turn on the inside to lock and unlock. Door is held shut by the roller latch. The roller pressure adjustment can assist in securing large and heavy doors, and doors subject to wind, yet allow free access through the door while unlocked. These locks also suit swing through doors with a matching double lip strike. Mortice Single Action Lock 1072 – 1073: Key on the outside withdraws the latch bolt. Lever handle on the inside withdraws the latch bolt at all times to open the door. Dead locking function is included in the lock. 90
4
Straight or shaped handle above the lock and in line with the cylinder. More suitable for medium length handles to minimize the vertical spread of the lock and handle. Use 60, 70, and 90mm backset locks. Solid core doors. These allow more freedom with lock backset and allow the handle to be positioned adjacent to lock. Extra-wide and over-height doors expand options to use large handles.
Examples 1,2 and 3. If roller locks are used, pull handles are needed on both sides of door. An option is to use a large handle on the outside and a smaller handle on the inside. If a night latch is used, pull handles can be fitted both sides of door, or a pull turn on the inside instead of a pull handle, refer to chant™ Escutcheons. For options in mounting pull handles, refer to chant™ Technical.
1
2
3
4
This series of mortice locks and latches have been designed for standard, narrow stile and rebated doors in a range of backsets. They also feature a ‘minimal’ lever handle rotation of only 40˚. The 72mm spindle to cylinder barrel centre line allows for a practical separation of lever handle rose and turn escutcheon without the appearance of crowding the components. It also allows for the same length back plate to be used throughout a project for entrance doors, narrow stile doors, internal doors and doors with a privacy function utilising the chant™ Cam Adapter 1250.
200 140 72
All locks have 8mm spindle hubs and are reversible. When ordered they are handed to suit the handing requested with the strike.
X
24
Y
Lock Strikes for Standard Doors 1005b 1005a
Lock Strike Packer 1007a/b
When these locks are to be used with unsprung lever handles, specify ‘HD’ after the lock code number. Mortice Lock Dimensions Model: Backset: X 1000 35 1001 45 1002 60 1003 70 1004 90
Case depth: Y 50 65 80 90 110
accessories mortice locks & latches
Mortice Locks
Mortice Locks 1000/1001/1002/1003/1004
Horizontal fixing centres: Plate furniture only 38 – 41mm 38 – 41mm 38 – 41mm 38 – 41mm
Lock Strikes for Standard Doors 1005a/b These strikes are handed to avoid compromising the design and installation aesthetics of universal, long lip strikes. – Full length strike box – Standard strikes measure 20mm from the lock centreline to the bend of the lip.
Extended Lock Strikes 1006a/b Lock Strikes for Rebated Doors 1008b 1008a
–
Extended 50mm from standard. These strikes can be cut back to suit the door frame. Specify the length required from the lock centreline to the edge of the door frame. The bent lip, 10mm wide, is additional to the width specified.
Strike Packer 1007a – 10mm/1007b – 8.5mm For aluminium door frames – Aluminium 10mm or 8.5mm thick x 24mm wide – Natural anodised finish
Lock Strikes for Rebated Doors 1008a/b – –
Lock packer included with these strikes Standard strikes measure 20mm from the lock centreline to the bend of the lip.
Extended Lock Strikes for Rebated Doors 1009a/b –
Extended 50mm from standard. These strikes can be cut back to suit the door thickness. Specify the length required from the lock centreline to the edge of the door. The bent lip, 10mm wide, is additional to the width specified.
91
Mortice Latches
accessories mortice locks & latches
Mortice Latch 1011/1012/1013
Mortice Latch Dimensions Model: Backset: Case depth: Horizontal fixing X Y centres: 1011 45 65 38 - 41mm 1012 60 80 38 - 41mm 1013 70 90 38 - 41mm
120 60 25
X
24
Y
Latch Strike for Standard Doors (universal) 1015
Strike Packer 1017a/b
Latch Strikes for Rebated Doors 1018
The latches have 8mm spindle hubs, are reversible, and can be handed on site. When these latches are to be used with unsprung lever handles, specify “HD” after the latch code number.
Latch Strike for Standard Doors 1015 –
Standard strikes measure 20mm from the lock centreline to the bend of the lip and are of a universal design
D-Strike for Standard Doors 1015a Extended Latch Strikes 1016 –
Extended 50mm from standard. These strikes can be cut back to suit the door frame. Specify the length required from the lock centreline to the edge of the door frame. The bent lip, 10mm wide, is additional to the width specified.
Strike Packer 1017a – 10mm/1017b – 8.5mm For aluminium door frames – Aluminium 10mm or 8.5mm thick x 24mm wide – Natural anodised finish
D-Strike for Standard Doors (universal) 1015a – not shown
Latch Strike for Rebated Doors 1018 – – –
Mortice Night Latch 1021/1022/1023
Universal design Lock packer included with these strikes Standard strikes measure 20mm from the lock centreline to the bend of the lip.
Extended Latch Strike for Rebated Doors 1019 – 150
90
Extended 50mm from standard. These strikes can be cut back to suit the door thickness. Specify the length required from the lock centreline to the edge of the door. The bent lip, 10mm wide, is additional to the width specified.
Mortice Night Latches Night Latches have both deadlock and hold-back functions.
55
X Y
Mortice Night Latch works with Latch Strike 1015 (standard doors) and Strike Packer 1017a/b above Night Latch Strikes for Rebated Doors 1028b 1028a
24
Mortice Night Latch Dimensions Model: Backset: Case depth: X Y 1021 45 65 1022 60 80 1023 70 90
Latch Strike for Standard Doors Use Strike 1015 above Extended Latch Strikes Use Extended Latch Strike 1016a/b above
Strike Packer Use Strike Packer 1017a/b above Night Latch Strikes for Rebated Doors 1028a/b –
Standard strikes measure 20mm from the lock centreline to the bend of the lip. Lock packer included
Extended Latch Strikes for Rebated Doors 1029a/b –
92
Extended 50mm from standard. These strikes can be cut back to suit the door thickness. Specify the length required from the lock centreline to the edge of the door. The bent lip, 10mm wide, is additional to the width specified.
Mortice Deadbolt 1030/1031/1032/1033
Mortice Deadbolt Dimensions Model: Backset: Case depth: X Y 1030 35 50 1031 45 65 1032 60 80 1033 70 90
150 90
Deadbolt Strike for Standard Doors 1035 55
Strike Packer 1037a – 10mm/1037b – 8.5mm X
24
Y
Standard Strike 1035
For aluminium door frames (not shown) – Aluminium 10mm or 8.5mm thick x 24mm wide – Natural anodised finish
Deadbolt Strike for Rebated Doors 1038a/1038b
Deadlock Strikes for Rebated Doors 1038a 1038b
–
accessories mortice locks & latches
Mortice Deadbolts
Lock packer included with these strikes
Mortice Sliding Door Locks
Mortice Sliding Door Lock 1040/1041/1042
Mortice Sliding Door Lock Dimensions Model: Backset: Case depth: X Y 1040 35 50 1041 45 65 1042 60 80
150
Sliding Door Lock Strike 1045
90
55
X
24
Y
Sliding Door Strike 1045
93
Mortice Roller Locks
Mortice Roller Lock 1051/1052/1053/1054
accessories mortice locks & latches
The Mortice Roller Locks and matching Strike Plates have been designed for standard, narrow-stile, rebated and swing-through doors. Roller projection adjusting screw 67 Roller pressure adjusting screw
235 175 63
Outline of Chant Cylinder Escutcheon: Ø50mm
55 30 X
24
Four backsets are available, 45mm, 60mm, 70mm and 90mm for matching of locks to different types of doors and handle configurations. The range of backset locks are particularly suitable for use with chant™ curved pull handles where the lock can be placed within the arc of the handle or adjacent to a straight handle. They also facilitate the vertical alignment of the cylinder barrel and pull handle when required, allowing the cylinder to be placed in the middle of the door stile. The locks feature adjustment from the faceplate for roller projection and pressure. The roller pressure adjustment can assist in securing large and heavy doors, and doors subject to wind, yet allow free access through the door while unlocked. A cautionary note is that increased roller pressure does make it harder to open and close the door.
Y
The two holes in the lock case allow for a pull handle mounting bolt to pass through the case to minimise the vertical separation of the handle and the cylinder escutcheon.
Roller Lock Strikes for Standard Doors 1055b 1055a
The pressure adjustment also allows for very light settings when appropriate. Mortice Roller Lock Dimensions Model: Backset: Case depth: X Y 1051 45 60 1052 60 75 1053 70 85 1054 90 105
Roller Lock Strikes for Standard Doors 1055a/b – – – – –
Ramp for roller to roll up when door closing Downward ramp for the roller to extend into, securing the door against its backstop Integral strike box behind the roller ramp Separate strike box for lock bolt Standard strikes measure 20mm from the lock centreline to the bend of the lip.
Extended Roller Lock Strikes 1056a/b –
1056a/b
94
Strike Packer 1057a/b
70
Extended 50mm from standard. These strikes can be cut back to suit the door frame. Specify the length required from the lock centreline to the edge of the door frame. The bent lip, 10mm wide, is additional to the width specified.
Strike Packer 1057a – 10mm/1057b – 8.5mm For aluminium door frames – Aluminium 10mm or 8.5mm thick x 24mm wide – Natural anodised finish
1058b
Roller Lock Strikes for Rebated Doors 1058a/b – –
Ramp for the roller to roll up when the door is closing Downward ramp for the roller to extend into, securing the door against its backstop Integral strike box behind the roller ramp Separate strike box for lock bolt Lock packer included with these strikes Standard strikes measure 20mm from the lock centreline to the bend of the lip.
– – – –
Extended Roller Lock Strikes for Rebated Doors 1059a/b –
Extended 50mm from standard. These strikes can be cut back to suit the door thickness. Specify the length required from the lock centreline to the edge of the door. The bent lip, 10mm wide, is additional to the width specified.
Roller Lock Strike for Swing-through Doors 1060 (double lip style) – – – – Roller Lock Strikes for Swing-through Doors 1060 (double-lip style)
accessories mortice locks & latches
Roller Lock Strikes for Rebated Doors 1058a
Ramps for the roller to roll up when the door is closing V-recess in the centre to locate the door Separate strike box for lock bolt Specify jamb width required when ordering, ie. 1060 – 120mm 10mm wide lips are additional to the jamb width unless otherwise stated
–
Handing of Strikes Single Doors Doors that open OUT
a
Inside
b
Outside
Doors that open IN
b
Inside
a
Outside
Double Doors Doors that open OUT
maximum width 150
a Doors that open IN
b
Inside
Outside
b
Inside
Outside
a
95
Mortice Roller Latches
accessories mortice locks & latches
Mortice Roller Latch 1061
Mortice Roller Latch 1061
Roller projection adjusting screw
155 95
Roller pressure adjusting screw
60
Roller Latch Strike for Standard Doors 1065
24
Extended Roller Latch Strike 1066
Roller Strike Packer 1067a/b
The Mortice Roller Latch is designed for standard, narrow stile, rebated and swing-through doors. It can be installed on the stile or on the head of the door. This Roller Latch is particularly suitable for swing-through doors to locate the door in the closed position, to receive an electric locking bolt.
Roller Latch Strike for Standard Doors 1065 – – – – –
Universal Ramp for the roller to roll up when the door is closing Downward ramp for the roller to extend into, securing the door against its backstop Integral strike box behind the roller ramp Standard strike measures 20mm from the lock centreline to the bend of the lip.
Extended Roller Latch Strike 1066 –
Extended 50mm from standard. These strikes can be cut back to suit the door frame. Specify the length required from the lock centreline to the edge of the door frame. The bent lip, 10mm wide, is additional to the width specified.
Roller Strike Packer 1067a – 10mm/1067b – 8.5mm 70
Roller Latch Strike for Rebated Doors 1068a
1068b
For aluminium door frames – Aluminium 10mm or 8.5mm thick x 24mm wide – Natural anodised finish
Roller Latch Strike for Rebated Doors 1068a/b – – – –
Ramp for roller to roll up when the door is closing Downward ramp for the roller to extend into, securing the door against its backstop Integral strike box behind the roller ramp Standard strikes measure 20mm from the lock centreline to the bend of the lip.
Extended Roller Latch Strikes for Rebated Doors 1069a/b –
Extended 50mm from standard. These strikes can be cut back to suit the door thickness. Specify the length required from the lock centreline to the edge of the door. The bent lip, 10mm wide, is additional to the width specified.
Roller Latch Strike for Swing-through Doors (double lip style) 1070 Roller Latch Strike for Swing-through Doors 1070
96 maximum 150
– – –
Ramp for roller to roll up when the door is closing V-recess in the centre to locate the door Specify jamb width required when ordering, ie. 1070 – 120mm 10mm wide lips are additional to the jamb width, unless otherwise specified
Mortice Single Action Lock 1072/1073
Mortice Single Action Lock 1072 Key on the outside withdraws the latch bolt. Lever handle on the inside withdraws the latch bolt at all times to open the door. Dead locking function is included in the lock.
170
Faceplate made from 316 stainless steel with brass case, and brass and stainless steel components. This lock has an 8mm spindle hub, and the latch bolt is reversible.
110
X
24
Y
Lock Strike for Standard Doors (universal) 1015
Single Action Lock Strikes for Rebated Doors 1078a 1078b
The lock case is machined with elongated slots to mount the door handles. They are supplied with offset nuts that allow the fitting of lever handles on a rose with 38mm or 41mm fixing centres. This allows the handle to be securely fastened with the door sandwiched between the handle rose and the lock case. A packer is provided to centre the lock body within a 22mm mortice.
accessories mortice locks & latches
Mortice Single Action Locks
Mortice Single Action Lock Dimensions Model: Backset: Case depth: X Y 1072 60 85 1073 70 95
Lock Strike for Standard Doors 1015 – –
Universal design Standard strikes measure 20mm from the lock centreline to the bend of the lip.
Extended Lock Strikes 1016a/b –
Strike Packer 1017a/b
Extended 50mm from standard. These strikes can be cut back to suit the door frame. Specify the length required from the lock centre line to the edge of the door frame. The bent lip, 10mm wide, is additional to the width specified.
Strike Packer 1017a – 10mm/1017b – 8.5mm For aluminium door frames – Aluminium 10mm or 8.5mm thick x 24mm wide – Natural anodised finish
Lock Strike for Rebated Doors 1078a/b – –
Lock packer included with these strikes Standard strikes measure 20mm from the lock centreline to the bend of the lip.
Finishes available for locks, latches and strikes Stainless steel SS Copper plate COP Bronze plate* BP* *This is a brass/bronze plated finish on stainless steel as an approximate match for bronze handles 97
accessories twin bolts
Twin Bolts
Options:
This series of mortice locks and latches are designed primarily for wooden, double entrance doors. The doors can then be opened simultaneously to provide a grand entrance, opening the doors “the way the butler used to”.
A. Two Point Latch and Bolt/Lockable 1090
The doors can be rebated or square edge and must be custom built to provide a recess to allow for the internal vertical rods to operate the latch or locking bolts. This is an alternative to exposed, surface espagnollete rods. These mechanisms can be used with the following options of door hardware for the lockable versions: – Lever handles outside and inside – Lock cylinder on one, or both door leaves, or neither side of either door – Cylinder or thumb turn on the inside – Pull handles on the outside with no access; lever handle surface mounted on the inside, with lock cylinder, or turn, or neither function. This type of “door set” is custom designed because of the various options with doors and operating door hardware, as they are site specific. Consult chant™ with your requirements.
Used where there is no sill at the bottom of the door. The latch secures the door at the top and the bolt fits into an elongated dust socket or strike on the floor. When the lever is fully operated, both latch and bolt withdraw. The bolt ‘catches’ and stays retracted in the mortice lock, allowing the door to be opened. When the levers are released, the bolt, which is retracted, will not scrape on the floor. When the door is shut and latches at the top, the release button below the lever handle can be pushed to release the bolt and secure the door. This feature can also be used to fasten the door in the open position with the bolt secured in a second dust socket or strike. These locks can use any of our chant™ or Mason door handles on plates in the groups; 30, 130, 250, and 310 as detailed in chant™ Technical on pages 104 – 109. When the lock in option A is used, the inside lever handle plate requires the bolt release button to be fitted, specify “R” after the plate code number when ordering the handles
When the locks from the options above are fitted to rebated doors, a half depth lock packer is used behind each lock to minimise the visual offset, of the lever handle from the edge of the door, on both sides of the door. On square edge doors, a brush type weather seal can be used as a draught strip to fill the gap between the doors. This requires dimensional accuracy on the installation of the doors, and allowance for the possible expansion and contraction of the doors due to temperature and humidity changes. The lever handle back set from the faceplate of the lock is 70mm, and the bolt or rod, 40mm.
Bolt release button
The construction of the door to provide the recesses for the operating rods can be as detailed in the drawings on page 83 Flush Pull Bolts/Conceal-fixed.
Installation 1. The morticed lock or latch mechanism is fitted to the door in the prepared recess. 2. The pull rods for the latches or bolts are cut to length to a calculation of door size and handle height. 3. The pull rods are then secured into the lock bolt or tubular latch with thread locking compound 4. The assembly is then inserted into the prepared rod hole and screwed into the lock or latch body, until the correct vertical adjustment is achieved. 5. The faceplate of the tubular latch will drop into its prepared recess and is then fastened with two screws, or the guide plate fitted over the locking bolt. The guide plate has a slotted hole to suit the round bolt which has two flat surfaces to prevent the bolt from rotating.
98
Dust Sockets Designed with a round ended, elongated opening so that there is tolerance for installation and any expansion or shrinkage in wooden doors. Flange diameter: 38mm Body diameter: 25mm Length: 50mm
Dust Socket Screw-fixed 1098
Dust Socket Glue-fixed 1099
C. One or Two Point Latch 1092
Used where there is a sill at the bottom of the door. The lever handles when operated, withdraw both latches allowing the doors to be opened. The doors self latch when closing. Operating the lock by a double cylinder lock, or single cylinder on the outside and a thumb turn on the inside, locks and unlocks the handles.
The cylindrical latch mechanism fits into a circular hole, either partially or fully through the door. It is secured into the recess with screws. The lever handles are then tie-screwed through the mechanism. When the levers are operated, the latches retract. The mechanism is suitable for; – a single handle on one side. This is surface fixed to the mechanism – handles both sides, tie-screwed through the mechanism and door – a single latch at the top only – horizontal fixing of the lever handle is at 38mm centres
accessories twin bolts
B. Two Point Latch/Lockable 1091
The mechanism shown below has a pair of Angle Lever Handles attached.
Latch Strike 1015 D-Strike 1015a, or custom strike made to suit site requirements
99
accessories cylinders & turns
Profile Cylinder and Turn
Profile Double Cylinder
Generally all key cylinders have a C4 profile. Cylinders indicated below with ‘*’ are Union and have Union Profile keys.
Profile Single Cylinder
Profile Single Turn
Cylinder and Turn Options: Refer to following diagram to calculate overall length required, based on thickness of door added to thickness of back plate(s) and/or escutcheon(s). overall cylinder length single turn
single cylinder
Remember to allow for the protrusion of the cylinder or turn for the lever handle back plate, 12.5mm, or escutcheons – 7mm or 9mm. Refer chant™ Escutcheons, page 68 for thickness. door thickness
length to centreline
door thickness
Cam Adapter 1250
model Profile Cylinders and 1200 - 3 pin 1201 - 5 pin 1202 - 6 pin *1203 - 6 pin 1204 - 5 pin
length Turns 42mm 62mm 70mm 82mm 90mm
Profile Double Cylinders 1210 - 3 pin 42mm 1211 - 5 pin 62mm 1212 - 6 pin 70mm *1213 - 6 pin 82mm 1214 - 5 pin 90mm Profile Single Cylinders 1220 - 3 pin 21mm to door centreline 1221 - 5 pin 31mm to door centreline 1222 - 5 pin 35mm to door centreline Profile Single Turns 1230 1231 1232
21mm to door centreline 31mm to door centreline 35mm to door centreline
Profile Cylinder Turn Adapter 1241/1242/1243/1244 All profile cylinder locks can use a chant™ Profile Cylinder Turn Adapter with chant™ door handles and escutcheons. Cylinder plates can be used on the outside of the door with the adapter bar connecting to the slot in the back of the thumb turn on the inside plate, or standard turn escutcheon (401 etc.). Specify door thickness when ordering this product. Refer to Technical pages 104 – 109, and chant™ Escutcheons page 68 for further details.
Profile Cylinder Turn Adapter 1241/1242/1243/1244
100
Cylinders and Turns
Remember to allow for the protrusion of the cylinder for the lever handle back plate – 12.5mm, or escutcheons – 7mm or 9mm. Specify door thickness when ordering this product. Refer chant™ Escutcheons, page 68 for thickness. Note: The Cylinder Escutcheon on this side is concentric with the cylinder body. The Turn Escutcheon on the opposite side is above the Cylinder Escutcheon and is concentric with the cylinder barrel. Hole preparation for the cylinder through the door must be made accordingly.
1241 1242 1243 1244
31mm 35mm 40mm 45mm
to to to to
door door door door
centreline centreline centreline centreline
Cam Adapter 1250 The Cam Adapter 1250 has been designed to be used with chant™ Mortice Locks. They provide an improved aesthetic over conventional profile emergency/turns, by allowing the use of plates with thumb and emergency turns, or using standard turn and emergency escutcheons. The Cam Adapter is operated by the 6mm x 2mm Turn Bar (A) on chant™ Thumb Turns – refer Technical, pages 104 – 113. Some brands of profile cylinder locks can be converted with a chant™ Cam Adapter and are lock specific, refer to chant™ to confirm suitability for your lock type.
Product Finishes Satin chrome plate SCPV Polished brass – Uncoated PBU Copper plate COP Aged brass AB* *This is an approximate colour match for polished bronze and satin bronze-aged handles and escutcheons
chant™ custom manufacture Some examples of pull handles, lever handles and a cabinet knob in polished bronze that have been requested by specifiers for special projects.
custom accessories manufacture
Some examples of custom pull handles
Cubic Pull handle with custom surface detail
Customised Angle Lever Handle with leather hand-grip
Customised fixed cabinet knob
101
chant™ Arc 542 Pull Handle
technical
94 104
chant™ Lever Handles on Rose
The world generally has two practices for the handing of door handles. We adopt the following method:
The following features are incorporated in the design of the roses: – The handles are reversible on the roses – 4 hole back to back fixing, 2 holes vertically for use with tubular latches and 2 holes horizontally for use with mortice locks – Fixing centres available: – 38mm and 41mm – Spring return on all handles – Snap on rose cover to provide concealed fixing with screw driver recess to assist removal (these are generally on the inside rose only) – Fixing plate available to lock the handle from turning – Spindles supplied, 7.6mm or 8mm – 5/32” x 3” BSW (76mm) stainless steel screws supplied – Three rose cover styles: F=Facet, R=Radius, S=Square to complement lever styles and escutcheons in the 3400/3410/3420 Series – Rose cover styles: P=Pyramid and C=Cylinder are designed for the Cubic and Rod/Angle lever handle styles. These styles are complimented by the escutcheons in the 3430 and 3450 series.
Handling is necessary in the following situations: – When lever handles are to have their visible-fixed side on the inside, and the concealed-fixed side on the outside. – When lever handles are asymmetrical, i.e. cannot be reversed. – When lever handle back plates have different functions on each side of the door, i.e. lock cylinder on one side, thumb turn on the other. – Pull handles that are asymmetrical. Hinges We do not consider where the hinges are, as some doors do not have hinges. Our terminology applies to doors that swing out, swing in, slide to the left or to the right. “Outside” is generally the outside of the building, or when standing in front of a door in a; – Foyer, opening to the dinning room, or lounge, or office – hall opening to a bedroom, – bedroom opening to an ensuite, – or the most commonly viewed side , – or whichever side you choose is the “outside”. Pairs of handles back to back The outside is the side that has the concealed-fixed handle on it, or the side which is fixed by the handle fastened on the inside. Refer page 110, Mounting Options. 1. To determine the handing, select the side of the door which is the ‘outside’ or the most commonly viewed side. The handle on this side of the door is the concealed fixed handle. 2. If the handle is on the right, it is a RIGHT HAND pair of door handles, if on the left, it is a LEFT HAND pair of door handles. Note: Applies to doors that open IN or OUT Single Handle If the handle is on the right, it is a RIGHT HAND handle, on the left, it is a LEFT HAND handle.
Single Swing Doors
Left Hand
Sliding Doors
Left Hand
Rebated Doors
Right Hand Right side of door leaf
Inside Doors Opening In
Outside Doors Opening Out
Right Hand
Rose Types 41F/41R/41S/41P/41C F=Facet/R=Radius/S=Square/P=Pyramid/C=Cylinder 41mm fixing centres for: – Tubular latches, 60mm backset or longer – Lockwood 3500 Series mortice lock (Australia) – NT Falcon mortice lock (USA)
Handle Type
Rose Style
Handing
Lever (L) Fixed (F)
Finish
Spindle Size
Quantity
531
38F
LH
L
SCPV
8mm
5pr
It is recommended that the lock type is stated when ordering lever handles. Right Hand
Fixed Leaf
Outside
Rose Types 38F/38R/38S/38P/38C F=Facet/R=Radius/S=Square/P=Pyramid/C=Cylinder 38mm fixing centres for: – Tubular latch: 60mm backset or longer – Profile cylinder mortice locks: • AGB, CES, chant™, CISA, Dorma, FSB, GSV, Häfele, JADO, KFV, Protector Series, SAB • Legge 8762, 57mm backset – Oval cylinder mortice locks: • Astra Brass and Astra S Series • Legge 990 MF • Union 2041, 127mm backset (has the lock cylinder horizontally in line with the lever handle) • Union 2241, 57mm and 82.5mm backsets – Mortice latch: Union 2677, 57mm backset
Example and specification of an order for lever or fixed handle on rose.
Inside
Outside
handing/lever chant handles on rose
Handing of Handles
refer chant™ Product Finishes 4–5 Left Hand Left side of door leaf
105
chant door handle plates
chant™ Door Handle Plates
The combinations of chant™ and Mason handles on different plate styles, allow them to be used to fit a variety of design applications, from contemporary to traditional. Narrow plates for narrow stiles and French doors, wider plates on solid internal doors, and large plates for entrance doors.
Plate styles Plates with square edges A1 A2 A3
A4
All chant™ and Mason handles can be fitted to the plates for all functions, except the Mason Swim lever handle in narrow style applications. The forward overhang of this handle style does not allow it to be used on locks with a backset of less than 55mm.
Plates with soft edges B1 B2
B3
Plate dimensions The 32mm and 38mm plates are designed for glazed aluminium and wooden doors where there is space for narrow backset locks only (30mm minimum backsets), and on solid doors where the narrow plate style is required. Handles are not reversible on these plates. The 44mm and 50mm wide plates are designed for latches and locks with a minimum backset of 45mm, and are reversible LH/RH when used with symmetrical handle styles. All plates are 12.5mm deep.
B4
Fixing The outside plates are concealed fixed and fastened to the door with two screws and mounting collars from the inside of the door. The inside plate slides over the mounting collars and is secured by two socket set screws on the top and bottom edge of the plate. Plates with chamfered edges C1 C2 C3
C4
C5
When plates with an emergency turn are required to have a coloured indicator function showing the lock status, specify ‘i’ after the plate number: eg 22i. 3-point locking systems All lever handles on plates can be used with 2 or 3-point locking systems where the handle is operated upwards to set the bolts. Specify 3PL in the order code (Plate Combination), when ordering.
This style C1– C5 is available only in 38mm, 44mm and 50mm wide plates Examples of handles on plates, and with turn options
Sabre 531 Handle on C4-250 Plate
Arc 551 Handle on B3-256 Plate with a conventional profile cylinder and turn
To Create a Specification 1. Select handle style. 2. Select plate style from the chart (A1 – C5). 3. – Select plate width from the following: 32mm, 38mm, 44mm, 50mm – Select the group corresponding with the lock type required, eg. 30–38 group for a chant™ lock. – Select the plate number to match the function for both outside and inside plates (if a pair is required) eg. 31+38, or a single plate only for outside or inside, eg. 30 or 35. 4. Select handing – refer to ‘Handing of Handles’ on page 105. 5. Select handle function: Lever (L) or Fixed (F) 6. Select handle finish. (Alternative finishes on each side of the door may be specified – order carefully!) 7. Specify spindle size: 7.6mm or 8mm 8. Specify quantity required
Example of specifications required for an order 1. Handle Style
2. Plate Style
Sabre 531 C4
Delta 631 Handle on A2-258 Plate with a chant™ Cam Adapter, or Profile Cylinder Turn Adapter 106
3. 4. Plate Handing Combination
*
21+26
LH
5. 6. Lever (L) Finish or Fixed (F)
7. 8. Spindle Quantity Size
L
7.6mm
SCPV
2pr
Repeat this ordering sequence for each plate combination required for the project.
*Please note that an additional specification will be required: The spindle to cylinder barrel or thumb turn centreline dimension, for group 40 and 110 plates, ie. 72, 85 or 92mm.
32mm wide Plates Outside Plates – Concealed fixing. Left hand shown, refer to ‘Handing of Handles’ for handing specification, page 105
door handle chant plates
Inside Plates – Semi concealed fixing
Plates to suit: Tubular Latches 10
15 80 112
*
Plates to suit: AGB, CISA, ISEO, Millton, Protector Series 8500, SAB, Schlage 970, WELKA, etc. mortice locks – 85mm centres 20
21
22
27
26
25
60 216 Cylinder
Emergency Turn
*85 Cylinder
185 Thumb Turn
*
Plates to suit: chant™, Dorma, FSB, Häfele, JADO, KFV, NEMEF, etc. mortice locks – 72mm centres 30
31
32
33
35
38
37
36 46
*72
191 For locks with chant™ Cam Adapter
78 For locks with chant™ Cam Adapter
*72 160
Plates to suit a variety of profile cylinder locks. After the Plate Code Number, specify the spindle to cylinder barrel or thumb turn centreline dimension*. eg. 41+46 – 92mm 40
41
42
47
46
45
64 220
*
*
189
Plates to suit: Legge 995 MF, Lockwood 5582 – 30mm backset, Lockwood 6582 – 38mm backset narrow stile mortice locks 50
51
52
53
55
54
56
57 159 90
190
37
Plates to suit: Legge 990 Series and Lockwood 3570 Series mortice locks – 60mm, 89mm and 127mm backset 60
61
62
63
64
65
66
67 129 63.5
160
32
*
Plates to suit: Legge 8512, 8642, 8762, Yale 3100, Jackson, etc. mortice locks – 47.5mm centres 70
71
75
72
76
40
77 125
47.5
*
156
*
Plates to suit: Imperial G7000, G8020 etc. mortice locks – 51mm centres 80
81
82
83
85
86 156
For locks with chant™ Cam Adapter
40
87
*51
88 57
For locks with chant™ Cam Adapter
*51 125
*
Plates to suit: Protector Series 735, Medio ME44 (short or deep backset) etc. mortice locks – 48.5mm centres 90
91
92
95
96 156
40
*
48.5
97
107 125
chant door handle plates
38mm wide Plates Outside Plates – Concealed fixing. Left hand shown, refer to ‘Handing of Handles’ for handing specification, page 105.
Inside Plates – Semi concealed fixing
Plates to suit: Tubular Latches 105
100
80 112
Plates to suit a variety of profile cylinder locks. After the Plate Code Number, specify the spindle to cylinder barrel or thumb turn centreline dimension*. eg. 311+316 – 92mm 110
111
112
115
117
116 64
189
220 Cylinder
Emergency Turn
*
Cylinder
Thumb Turn
* *
Plates to suit: AGB, CISA, ISEO, Millton, SAB, Protector Series 8500, Schlage 970, WELKA, etc. mortice locks – 85mm centres 120
121
122
125
126
127 60
216
Plates to suit: chant™, Dorma, FSB, Häfele, JADO, KFV, NEMEF, etc. mortice locks – 72mm centres 130
131
132
135
133
185
*85 *
136
137
138
46 191
*72
For locks with chant™ Cam Adapter
160
78 For locks with chant™ Cam Adapter
*72
*
Plates to suit: Legge 8512, 8642 and 8762; Yale 3100, Jackson, etc. mortice locks – 47.5mm centres 140
141
142
145
146
147 40
*47.5
156
125
*
Plates to suit: Imperial G7000, G8020 etc. mortice locks – 51mm centres 150
151
152
153
155
156
157
40
*51
156
For locks with chant™ Cam Adapter
158 57
For locks with chant™ Cam Adapter
*
Plates to suit: Protector Series 735, Medio ME44 (short or deep backset) etc. mortice locks – 48.5mm centres 160
161
162
165
166 156
40
167 125
*48.5
Plates to suit: Legge 990 Series and Lockwood 3570 Series mortice locks – 60mm, 89mm and 127mm backset 170
171
172
173
174
175
176 160
177 129 63.5 32
108 Plates shown on grey suit chant™ Mortice Locks. Refer pages 90 – 97
125
*51
Handles on these plates are reversible on-site if the handle is a symmetrical style
Outside Plates – Concealed fixing. Left hand shown, refer to ‘Handing of Handles’ for handing specification, page 105.
Inside Plates – Semi concealed fixing
door handle chant plates
44mm wide Plates
Plates to suit: Legge 990 Series and Lockwood 3570 Series mortice locks – 60mm, 89mm and 127mm backset 210
211
212
Cylinder
Emergency Turn
213
214 215
216
217 Thumb Turn
Cylinder 166
135 63.5 37.5
*
Plates to suit: Legge 8512, 8642 and 8762; Yale 3100, Jackson, etc. mortice locks – 47.5mm centres 220
221
222
225
226
227 37.5
*47.5
166
135
*
Plates to suit: Imperial G7000, G8020 etc. mortice locks – 51mm centres 230
231
232
233
235
236
238
237 37.5
*51
166 For locks with chant™ Cam Adapter
135
57 For locks with chant™ Cam Adapter
*51
*
Plates to suit: Protector Series 735, Medio ME44 (short or deep backset) etc. mortice locks – 48.5mm centres 240
241
242
245
246
247 37.5
*48.5
166
Plates to suit: chant™, Dorma, FSB, Häfele, JADO, KFV, NEMEF, etc. mortice locks – 72mm centres 250
251
252
253
255
135
*
256
258
257 46
46
46
*72
78
*72
160
191 For locks with chant™ Cam Adapter
For locks with chant™ Cam Adapter
50mm wide Plates Handles on these plates are reversible on-site if the handle is a symmetrical style Plates to suit: chant™, Dorma, FSB, Häfele, JADO, KFV, NEMEF, etc. mortice locks – 72mm centres 310
311
312
313
315 200
For locks with chant™ Cam Adapter
Plates with Alternative Turn Functions
Cam Adapter
Profile Cylinder Turn Adapter
*
316
318
317 55
55
55
*72
78
*72
For locks with chant™ Cam Adapter
Some profile cylinder locks can be converted with a chant™ Cam Adapter, to allow the use of plates with thumb and emergency turns. This provides an improved aesthetic appeal over conventional profile cylinder and turns. The cam adapter is operated by the 6mm x 2mm turn bar (A) on the Thumb Turn – refer to chant™ Escutcheons, page 68, eg. used typically on 253+258 plates above. Or, using chant™ Profile Cylinder Turn Adapter. Cylinder plates can be used on the outside of a door with the adapter bar connecting with the slot in the back of the thumb turn on the inside plate, eg. 311+318 plates above. Refer to chant™ Cylinders and Turns, page 100 for more information on both products.
169
109
Mounting Option 1
Mounting Option 2
Back to Back (BTB) - Pairs of handles
Back Fixed (BF) - One pair of handles on two adjacent doors or a single handle on one door.
Outside
Inside Mounting collar
➞
chant pull handles
Pull Handles
Socket setscrew
Example and specification of an order for 2 pair Sabre 522 handles to be mounted back to back on 2 adjacent doors or 1 pair of Cobra 601 handles on a single door. Example/Handle
Mounting
Handing (if applicable)
Finish
Quantity
A/522 A/522 B/601
BTB BTB BTB
RH LH -
SCPV SCPV COP
1 pair 1 pair 1 pair
Example B
Example A
Right hand handle
Example and specification of an order for 1 pair of Luna 562 handles or 1 only Arc 541 handle. Example/Handle Mounting
Fastening Option
Handing Finish (if applicable)
C/562 D/541
FS DS
LH/RH RH
BF BF
Example C
PBZ SBZA
Example D
Left hand handle
*
*Note: This is a left handle because it is on the left side of the door leaf, when viewed from the "outside" or concealed-fixed side. Refer to chant Technical "Handling of Handles", page 105.
Fastening options for back fixed handles
110
Countersunk slotted screw M6 x 50mm
Code CS
Dome Screw - For glass or wooden doors M6 x 75mm standard length supplied, OR specify door thickness.
Code DS
Flat Screw - For aluminium or wooden doors M6 x 75mm standard length supplied, OR specify door thickness.
Code FS
Quantity
1 pair 1 only
Mounting Option 4
Surface Fixed (SF) - One pair of handles on two adjacent doors or a single handle on one door Wooden Doors only. Mounting collars are screwed to the door with 10g x 50mm (2’’) stainless steel screws. The handle is fixed to the collars with socket setscrews.
Used in situations where handles are necessary on both sides of a door, and a change in size is required from one side to the other. Example: Large handle on the outside of a front door with a smaller handle on the inside for the entry foyer.
Combination Handles (Pairs of dissimilar handles)
Top to Top, specify - TT
Mounting Collar
chant pull handles
Mounting Option 3
➞
Socket screwset
Surface fix
Example and specification of an order for 1 pair of Bow 502 handles or 1 only Cobra 602 handle. Example/Handle
Mounting
Handing (if applicable)
Finish
Quantity
E/502 F/602
SF SF
LH/RH -
SCPV PCP
1 pair 1 only
Bottom to Bottom, specify - BB Surface fix
Example E
Example F
This surface fixed option can also be used when handles are required on both sides of the door, when they must be mounted independently of each other.
Note: The options of ‘Top to Top’ or ‘Bottom to Bottom’ should be considered to obtain the preferred ‘ operating height of both handles, and their position in relation to the lock.
If the handles are a “handed” style, they must be ordered with the handing stated correctly for the handle on each side.
Example and specification of an order for combination handles.
If there is any doubt about our required specification on handing of handles when placing an order, please supply a sketch of the plan view of the door, showing the outside, the hinge position/swing of the door, position of the handle(s) and code number(s).
Handle Combination
Mounting
522/524
TT
Handing (if applicable) LH
Finish
SCPV
Quantity
1 pair
Options for Combination Handles 1. Larger handle on outside of door, smaller handle on inside of door eg. 522/524. 2. Both handles are typically from the same suite eg. Sabre.
111
chant pull handles
Pull Handles Mounting of Door handles on Glass or Sliding Doors. All chant™ and Mason handles can be mounted on wood, glass and aluminium stile doors. Additional accessories are as follows. Backing Washers Available for all Mason pull handles and applications. Type - BWA Used to prevent handle pillars or mounting collars crushing into ‘soft’ timber surfaces, or as a general backing washer between handle pillars and the door surface on any installation. Must be used on glass doors with all pull handles. 25mm washer diameter for PM01, PM10, PM11, PM12, PM21, PM31, PM32, PM41, PM42 handles. 22mm washer diameter for PM02, PM13, PM22, PM23, PM33, PM36, PM43, PM46 handles.
Offset Plates Offset Plates allow Mason Pull Handles to be mounted on narrow stile doors, where there is insufficient hand clearance between the handle and the edge of the door. Offset Plates are available for the following handles: PM01, PM02 PM10, PM11, PM12, PM13 PM21, PM22, PM23 PM41, PM42, PM43 Offset Plates vary in length according to the handle style, and the offset of the handle pillars to the vertical line. Nominal 35 Door stile
Handle
22mm or 25mm
Type - BWB Used on ‘soft’ timber sliding doors. 16mm spigot provides greater bearing load in a lateral direction. Use with all chant™ and Mason handles. Flat Screw 16mm
25mm
To order with handles specify: BWA or BWB/Finish required, as a suffix to the handle order specification. The finish on the washers may be different to the handles if required.
PM120 Offset Plate
PM120, for mounting a single handle
Pillar Handle
Glass Door Mounting All handles are suitable for mounting BACK TO BACK or SINGLY on glass doors. Hole positions on glass doors can be determined from the handle specification drawings. Particular care should be taken with any offset of mounting holes to obtain correct vertical alignment, e.g. PM01 Handle with 20mm offset. Ensure the offset is in the correct direction for left hand or right hand handles before making holes. M8 (8mm diameter) mounting screw for Mason PM00 -1000, PM00-800, PM09, PM21-1000, PM21-750, and chant™ Cobra 600 and Delta 620. M6 (6mm diameter) mounting screw for Mason PM01, PM10, PM11, PM12, PM21, PM31, PM32, PM41, PM42 handles and all other chant™ handles. M5 (5mm diameter) mounting screw for Mason PM02, PM13, PM22, PM23, PM33, PM36, PM43, PM46 handles. Minimum hole size in glass is 12mm for M8 screws and 10mm for M6 and M5 screws.
112
Glass Door Kit includes: nylon washers and sleeves, and backing washers type BWA. To specify: GDK/Finish (of BWA washers), as a suffix to the handle order specification.
PM121, for mounting a pair of handles
To specify: PM120/Handle style/Finish (one set of plates for mounting a single handle, one side only). PM121/Handle style/Finish (one set of plates for mounting a pair of handles back to back). i.e. PM121/PM02/SCPV/Quantity.
Attaching Plates These Attaching Plates are used to fasten a single chant™ or Mason handle onto a single action mortice lock on the inside of: – an entrance door with key entry, and a lever handle to withdraw the latch bolt to exit. – an egress door where the handle withdraws the latch On an entrance door, this allows for the use of a Chant or Mason pull handle on the outside of the door with a cylinder and escutcheon for key entry, and a lever handle on the inside. This attaching plate avoids the need to use dummy roses on the outside of the door. The plate is made from 3mm or 5mm thick brass.
Example of the assembly of a Pull Turn mounted onto a Legge 990 Lock using an Attaching Plate 495 Refer to chant™ Pull Turns, page 68 and Mason Pull Turns, page 26.
chant attaching plates
Cross section of a lever handle fastened onto the Attaching Plate and a Legge 990 Lock. The lever handle is on the inside, the lock cylinder and escutcheon is on the outside
Plate 495 is for Legge 990 Locks. The plate is attached to the lock body with one screw in the bottom corner. It brings the width of the lock case to a nominal 22mm wide, the width of a standard mortice for that lock. When the lock is installed, the plate is against the inside of the mortice. When the handle is fastened to the plate, the door is sandwiched between them. The fastening screws protrude into the lock case. Plate 496 is for Lockwood 3500 Series Lock and is 5mm thick. It fits into the recess on the appropriate side of the case and is retained in the recess with double sided tape. It also brings the nominal width of the case to 22mm. It is suitable for Chant lever handles on rose with 41mm fixing centres only.
Attaching Plate 495 for Legge 990 Series Mortice Lock
Plate 497 is for SAB Locks. The plate is attached to the lock body with two screws at the top and bottom of the plate. When the handle is fastened to the plate, the door is sandwiched between them. The fastening screws protrude into the lock case.
Attaching Plate 496 for Lockwood 3500 Series Mortice Lock
Attaching Plate 497 for SAB Mortice Lock
113
door morticing chant equipment
chant™ Door Morticing and Fitting Equipment This range of door machining equipment has evolved over many years to assist the installers of door hardware. It is used by: – building and interior partitioning fitout contractors – locksmiths – dedicated hardware installation contractors – joiners – door manufacturers – card access lock, suppliers and installers The additions of the Routing Jigs have proved highly valuable to the installers of chant™ and other proprietary hardware products, providing a professional finish to the installation. The Routing Jigs shown on page 117 are for our own product ranges. Visit our website for the latest listing of other jigs available to assist in the installation of other manufacturer’s hardware. This morticing machinery is the preferred equipment of choice in the New Zealand market for its durability and reliability.
114
Door Machining Equipment Trolley 6000 Designed for the efficient and convenient transport to, and around a site, of lock morticing machine and associated equipment. Specification • Machine trolley, manufactured from powdercoated steel tube • Pneumatic tyres for easy site movement • Well balanced with all equipment specially positioned • Complete with; – Lock morticing machine. – Face plate routing jig. – Mounting bracket and separate router for machining the face plate recess. – Vacuum cleaner with storage for accessories. – HPM Electresafe Powerboard. – 15 metre power lead. – Mounting bracket and electric drill – Coil cords fitted to all power tools for easy cable management Dimensions 480mm w x 600mm l 1030mm h Weight with above equipment: 40kg
Designed for quick and accurate morticing of doors. It machines the pocket that the body of a mortice lock fits into. Cranking the handle in a clockwise motion, raises and lowers the motor head assembly on the vertical guide rods, simultaneously feeding the motor head and cutter into the door. When the clutch nuts on the motor head are withdrawn, the motor head can be returned to the start position.
door morticing chant equipment
Lock Morticing Machine 6005
Specification • Robust construction • Standard router motor; Makita 3612C electronic speed control – allows low speed cutter operation capable of morticing fire doors with a steel cap around the central core. Minimum operating speed of 9000rpm also provides low noise level, yet still allowing sufficient speed for cutting wood. 2300watt/240 volt motor • Self centering door clamps with protective face pads. These are a generous length to avoid marking the door surface, and machined with ‘toe-in’ so that they grip at the tips first, then over their full length as the clamps tighten. • Router shaft enclosed with telescopic sleeves for safety • Simple adjustments for depth and height of mortice • Easy to grip and convenient handle to carry the machine • Shaving extraction system for operator safety, clean machine operation and work area • Clamps designed for door thicknesses: 30 to 80mm • Mortice height adjustment: 40 to 200mm • Mortice depth adjustment: 125mm • Cutter diameters available: 16mm, 19mm, 22mm, 25mm • Weight: 13.4kg
115
chant door morticing equipment
Faceplate Routing Jig 6010 Designed for quick and accurate routing for the lock faceplate and marking of spindle, cylinder, and door furniture fixing holes. Specification • Robust construction • Self centering door clamps with protective face pads • Door clamps hold the router plate square to the sides of the door • Centre block adjustment left to right to obtain perfect parallel alignment of the machined recess with the door faces • Template insert clips into the back plate. It is used to guide a router with a pilot guide on its base. Templates available to suit a variety of standard locks with a 3mm offset to suit a 9.5mm cutter • Special pilot guides can be made to order • Adjustable guides to suit router bases from 110 – 168mm diameter when a template guide is not available. The router guide bars and the templates eliminate the possibility of the router cutter accidentally cutting an oversize recess • Jig attachment bars on the door clamps are used to position the marking jigs accurately • Marking jigs available to mark hole positions for; spindle, cylinder, turn and fixing holes for door furniture, for a variety of standard locks • Light weight and easy to use • Clamps designed for door thicknesses: 30 to 80mm • Cutter diameter recommended – 9.5mm • Jig accepts drill attachment for tubular latches To order marking jigs: Specify: – Lock type – Door furniture type and lever rose or size/model of backplate To order Routing Templates: Specify: – Lock type/Face plate size, or if chant™ lock, specify Lock number with a prefix 6., eg. 61003.
116
Routing Templates for Faceplate Jig or other chant™ Hardware Installation Jigs that require templates. Order Template by the code number. When ordering templates for chant™ accessories specify the accessory part number, preceeded by “6”. i.e. Flush Pull 1401 becomes 61401. Each product may have more than one template option: Template A.
To cut the standard or primary recess for the body of the accessory, ie. Flush Pull 1401: 61401A.
Template B.
To cut the outer shape of the accessories. ie. Flush Pull 1401 (when it needs to be totally flush mounted): 61401B. Cuts a recess 38 x 100mm.
Template C.
To cut any other functioning recess that may be required, eg. on an Extended Sliding Bolt, the recess for the attaching pin protruding from the rear for the M8 extension rod to fasten to.
We also make an extensive range of jigs for the installation of other proprietary products. These can be found on our website: www.chantproductions.com
Tubular Latch Drill Jig 6020 + 24mm Augur
Universal Jig 6043
Clips into the Faceplate Routing Jig. Drill Bush for Extended Drill Size: Ø10mm 6021 Ø12mm 6022 Ø19mm 6023
10mm diameter x 1000mm Drill (for power cables) 6030
Vertical locating clamp 6040
Drill bushes slide into the Tubular Latch Jig for drilling specific hole sizes. Can be used with a 10mm diameter extended drill, to drill through the door for a power cable for an electric lock.
Sliding Flush Bolt Jig 6044
Used as a rest to locate jigs that are required to machine recesses on both sides of the door, ie. Flush Pull Jig 6043
Recessed Edge Pull Jig 6045
Strike Plate Jig 6041
Adjustable backset. Also used for: Flush Pulls, Privacy and Locking Flush Pulls, Extended Flush Sliding Bolts, Combination Pulls/Bolts
chant door morticing equipment
This series of Jigs complement the Lock Morticing Machine and the Faceplate Routing Jig. The Jigs 6040–6045 are for preparing doors for chant™ products.
Jamb Extension Bar 6042
Two clamp adjusting screws on one side and a single clamp screw on the other. This allows the Jig to be made parallel and move the the Jig to centralise it on the door.
Extended Flush Bolt Drill Jig (not shown) 6046 For drilling the hole into the stile for the extension rod.
117
chant general
General
Maintenance of chant™ Products
Ordering
Polished Surfaces
All hardware must be ordered as described in the respective sections. This will assist in providing hardware that can be installed, and function as required. Order sheets are available to assist with formulating the correct specification. Fax or email your request for copies, or visit www.chantproductions.com to download a PDF.
To maintain polished surfaces, use Brasso, or a similar metal polishing product.
Materials
Maintaining Your Plated Hardware
All door hardware is made from bronze or brass as the base metal. Handles and components are cast, forged, or machined from solid bar.
• Clean with a soft damp cloth with diluted detergent or a dry duster • Never use abrasive cleaners, scourers or rough cloths that may damage or scratch the plated surface • Never use chemical cleaners such as solvents or Brasso.
Special Requirements
Patina Surfaces To protect patina finishes, wipe occasionally with a proprietary bee’s wax or similar product.
Plate types on pages 107 to 109 can be modified to suit different lock and plate size configurations. Contact our Technical Division for assistance if standard specifications do not meet site or design requirements.
Product Specifications As chant™ and Mason hardware ranges continue to evolve, and the requirements of the construction industry expand, we reserve the right to change our specifications without notice. While we have taken every care in the preparation of this catalogue, we can take no responsibility for errors or omissions that have occured. If our products do not meet your site requirements, please forward your requests for us to evaluate customised solutions.
Fire Doors Contact chant™ for specific information on fire ratings. Please choose carefully before ordering chant™ hardware. There are many options, operating functions and technical details to be considered. Contact us should you have any questions.
118
© Copyright: Reproduction of this catalogue, in whole or in part, without written permission from Chant Productions Limited is strictly prohibited.
Finish Options
Product Warranty
All hardware is available in Combination or Split finishes.
Individual components of different finishes are assembled into a lever or pull handle, ie. satin chrome plate velvet lever and rose cover and polished chrome plate rose and handle boss.
Chant Productions Limited (Chant) warrants that its products will be free from defects in workmanship and materials for a period of five years from the date of purchase subject to the limitations below.
Split Finishes
Limitations
This is where different sections of a pull or lever handle can be processed in two finishes. The blend between the finishes can be ‘crisp’ along a ridge line, or ‘soft’ over a contoured area of the handle, eg. combination of Sand Polished Chrome and Polished Chrome. Contact chant™ to discuss your requirements.
Chant shall have no liability under this warranty for the following: 1. Failure due to incorrect installation or failure to follow fitting instructions or use of a product in a manner for which it was not designed. 2. Failure due to abuse, misuse or accident, or any failure due to dismantling, alteration or repair by any person not authorised by Chant. 3. Failure due to incorrect maintenance, failure to adhere to recommended maintenance procedures. 4. Fair wear and tear. 5. Cost of removal, reinstallation and freight. 6. Electroplated finishes on the products can deteriorate or discolour over time due to climactic conditions and consequently the warranty for plated finishes is limited to 24 months from the date of purchase. 7. “Living Finishes” (e.g. bronze and copper) that are designed to patina or otherwise change over time are excluded from our warranty.
Bronze Metal and “Living Finishes” All of our products are made of brass as the base metal and are used for the electroplated finishes, including copper. Almost all of our products are also available in bronze as the base metal. Uncoated brass, copper and bronze are used where the beauty of polished, natural, or patina finishes are required to compliment or enhance the décor. They are subject to colour change over time, depending upon; – Atmospheric conditions present, which can vary from low corrosion indoors, non coastal; to high corrosion, exterior, in coastal areas with salt laden air. – Wear patterns with use, from little used ornamental handles to high use handles. Greater use may wear the surface finishes back to the base metal and provide contrasting patina and semi polished surfaces. Combinations of the above factors, in varying degrees will provide unique and “Living Finishes”. These finishes as specified are therefore not guaranteed for colour fastness. Satin Nickle Plate is included in the “Living Finishes” group. It will oxidise to a minor degree over time, as it is a metal. Because of its colour, it is often the preferred match for hardware on natural finish timber doors and windows over other electroplated finishes like satin chrome plate. This natural ageing is deemed desirable in some markets. We do not lacquer this finish to protect it from oxidising (as often other brand products do). This is because lacquers will ultimately fail with use, through abrasion and chipping of the surface; and look inferior to a naturally ageing finish over the complete product. Products in the “Living Finishes” group can also be maintained as polished surfaces with standard proprietary metal polish cleaners.
chant general
Warranty Combination Finishes
Claims All warranty claims must be made in writing to Chant. The claim must be approved by Chant before any cost is incurred. Chant reserves the right to inspect the product in its installed state before a claim is approved. Chant shall at its sole discretion credit, repair or replace free of charge any product or part determined by Chant to be defective in breach of this warranty.
Liability Chant makes no other warranty of any kind expressed or implied in respect of Chant’s products. Chant’s sole responsibility is to repair and replace a product subject to a valid warranty claim. Under no circumstance will Chant be liable for indirect, incidental or consequential costs or damages, including removal and reinstallation costs, loss of operations or profits (whether direct or indirect), to the maximum extent permitted by law. Chant accepts no liability for personal injury or property damage resulting from failure to adhere to relevant installation operation and safety procedures. Nothing in this warranty excludes, restricts or modifies any condition, warranty, right or liability implied or protected by law if to do so would render this warranty, or any part of it, invalid or ineffective.
119
chant notes
chant notes
8/136 marua rd, ellerslie auckland, new zealand tel: + 64 9 526 4048 fax: + 64 9 526 4049 email:
[email protected] www.chantproductions.com
© chant productions limited 11/2006
chant productions limited
