Transcript
ZMOTION™ Lens and Pyroelectric Sensor Product Specification PS028609-0213
Copyright ©2013 Zilog, Inc. All rights reserved. www.zilog.com
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
ii
Warning: DO NOT USE THIS PRODUCT IN LIFE SUPPORT SYSTEMS.
LIFE SUPPORT POLICY ZILOG'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF ZILOG CORPORATION. As used herein Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. Document Disclaimer ©2013 Zilog, Inc All rights reserved. Information in this publication concerning the devices, applications, or technology described is intended to suggest possible uses and may be superseded. ZILOG, INC. DOES NOT ASSUME LIABILITY FOR OR PROVIDE A REPRESENTATION OF ACCURACY OF THE INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZILOG ALSO DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY INFRINGEMENT RELATED IN ANY MANNER TO USE OF INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED HEREIN OR OTHERWISE. The information contained within this document has been verified according to the general principles of electrical and mechanical engineering. ZMOTION and Z8 Encore! XP are trademarks or registered trademarks of Zilog, Inc. (An IXYS Company). All other product or service names are the property of their respective owners.
PS028609-0213
Disclaimer
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
iii
Revision History Each instance in the revision history table reflects a change to this document from its previous revision. For more details, refer to the corresponding pages or appropriate links provided in the table below.
Date
PS028609-0213
Revision Level
Page Number
Description
Feb 2013
09
Moved NCL-11 lens specification to Table 2; added the 2, 8 CM 0.77 GI V2 lens specification; alphanumerically reordered all lenses.
May 2012
08
Added the NCL-11 and EWA 0.3 GI V2 lens specifications.
36, 18
Nov 2011
07
Added the NCL-3R and NCL-10S lens specifications.
22, 34
Mar 2011
06
Intrusion lens specifications added.
38
Jan 2011
05
Modifications to some lens/sensor descriptions in Table 2 2.
Jan 2011
04
Updated to include two new Nicera sensors.
Nov 2010
03
Updated to new Zilog/IXYS logo and accepted Zilog All style; replaced all instances of ePIR with advanced passive infrared.
Sep 2010
02
Replaced Zilog logos, ePIR with ZMOTION, and Zdots with Module; fixed formatting and pagination issues; removed references to GP and General Purpose.
All
Oct 2010
01
Original issue
All
19, 29
Revision History
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
iv
Table of Contents Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 PIR Sensor Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ZMOTION Lens Selection Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ZMOTION Detection and Control Lens Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 6 AA 0.9 GI T1 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 CM 0.77 GI V2 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 CM 0.77 GI V3 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 CM 0.77 GI V5 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 CWM 0.5 GI V1 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 EWA 0.3 GI V2 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 NCL-3B Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 NCL-3R Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 NCL-9(26) Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 NCL-10IL Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 NCL-10S Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 NCL-11 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 ZMOTION Intrusion Detection Lens Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . LR 1.2 GI 12 V3 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VB 1.2 GI V1 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WA 1.2 GI 12 V4 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
38 39 40 41
Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
PS028609-0213
Table of Contents
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
1
Overview Zilog’s ZMOTION Detection and Control and Intrusion Detection product families provide integrated and flexible solutions for Passive Infrared (PIR)-based motion detection applications. These product families are based on the ZMOTION MCU, a high-performance microcontroller featuring integrated PIR motion detection algorithms. Each family includes a selection of lenses and PIR sensors to fit a wide range of application requirements. Each lens and sensor combination is optimized for its intended application by configuration settings loaded into the ZMOTION MCU ensuring the best possible performance while significantly reducing development risk and minimizing time to market. Zilog’s PIR Motion Detection Technology provides a dramatic improvement in both sensitivity and stability over traditional designs and is scalable to many market segments including Security/Intrusion Detection, Lighting Control, HVAC, Access Control, Vending, Display, Proximity, Power Management, Occupancy Sensing and many others. This document provides the zone patterns and mechanical dimensions for the Zilog-supported lenses and pyroelectric sensors included in the ZMOTION Family. Each supported lens and pyroelectric sensor combination is provided with an associated configuration file for the ZMOTION MCU. It is possible to use other lenses and pyroelectric sensors not directly supported by Zilog by developing the appropriate configuration settings based on one of the existing files. There are two general groups of lenses provided:
• •
ZMOTION Detection and Control for general motion detection applications ZMOTION Intrusion Detection for security applications
All lenses and pyroelectric sensors listed in this document are available from Zilog as a bundle (which includes MCU, lens and pyroelectric sensor) or individually from their associated manufacturers. Because Zilog is regularly adding new lens support to these ZMOTION product families, please obtain the latest version of this document from our website at: www.zilog.com/ZMOTION.
PS028609-0213
Overview
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
2
PIR Sensor Specifications The pyroelectric sensors included in the ZMOTION product families are manufactured by Nippon Ceramic Company Ltd. (Nicera). Please refer to their website for any specific information you may require. Table 1 shows the pyroelectric sensors available for both the ZMOTION Detection and Control and Intrusion Detection Families. Table 1. ZMOTION Pyroelectric Sensors Manufacturer
Part Number
Description
Nicera
RE200B-P
Basic Dual Element
Nicera
SDA02-54-P
Premium Dual Element
Nicera
SBDI46-504AA
Quad Element
ZMOTION Lens Selection Guide Select a lens and pyroelectric sensor based on the intended application from Table 2. Lenses and pyroelectric sensors for security/intrusion-related applications are listed in Table 3. Table 2. ZMOTION Detection and Control Lenses and Pyroelectric Sensors Part Number
Description
AA 0.9 GI T1 Lens Specification – see page 7
Animal Alley Array (88°) 35.6mm x 49.9mm Flat Fresnel lens 22.9mm focal length 25 meter range 22 equal segments
Recommended Applications
Configuration Header File
Corner wall mount or very API_INIT_01.h high ceiling with rectangular floor pattern
Pyroelectric Sensor RE200B-P SDA02-54-P
Warehouse Lighting (Bay Light) Combined Intrusion and Lighting Control HVAC
Note: *The NCL-11 and EWA 0.3 GI V2 lenses are not currently part of the standard ZMOTION bundled suite or offered in ZMOTION development kits. However, the optimized API settings for this lens are available in the ZMOTION Detection Lens and Pyro Sensor Configuration Guide (WP0018).
PS028609-0213
PIR Sensor Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
3
Table 2. ZMOTION Detection and Control Lenses and Pyroelectric Sensors (Continued) Part Number
Description
CM 0.77 GI V2 Lens Specification – see page 8
Ceiling Mount Array (360°) 37mm diameter circular lens
Recommended Applications
Configuration Header File
Pyroelectric Sensor
High ceiling mount for commercial lighting control
API_INIT_02.h
SBDI46-504AA RE200B-P
Commercial HVAC
19.6 mm focal length 12.2 m radius at 3.7 m height 4:1 floor coverage diameter-to-height ratio CM 0.77 GI V3 Lens Specification – see page 10
Ceiling Mount Array (360°)
Ceiling Mount for standard commercial heights
37mm diameter circular lens
Lighting Control
19.6mm focal length
Meeting rooms
API_INIT_02.h
RE200B-P SBDI46-504AA
HVAC Control
3.7m radius at 2.4m height 3:1 floor coverage diameter to height ratio CM 0.77 GI V5 Lens Specification – see page 12
Ceiling Mount Array (360°) 37mm diameter circular lens
High ceiling mount for API_INIT_03.h commercial and industrial applications
19.6mm focal length
Commercial Lighting Control
12.2m radius at 12.2m height
Commercial HVAC Control
RE200B-P SBDI46-504AA
2:1 floor coverage diameter to height ratio CWM 0.5 GI V1 Lens Specification – see page 15
Ceiling/Wall Mount Array (180°)
Wall or ceiling mount for API_INIT_04.h office or meeting room Circular lens with 24mm x lighting and HVAC control 24mm square base Room Lighting and HVAC Control 14.2mm focal length
RE200B-P SBDI46-504AA
Board mount clip-in Note: *The NCL-11 and EWA 0.3 GI V2 lenses are not currently part of the standard ZMOTION bundled suite or offered in ZMOTION development kits. However, the optimized API settings for this lens are available in the ZMOTION Detection Lens and Pyro Sensor Configuration Guide (WP0018).
PS028609-0213
ZMOTION Lens Selection Guide
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
4
Table 2. ZMOTION Detection and Control Lenses and Pyroelectric Sensors (Continued) Part Number
Description
EWA 0.3 GI V2 Extra Wide Angle Wall Lens Specifi- Mount Array (180°) cation – see 14mm x 28mm page 18 7.6mm focal length 5 meter range 16 equal segments
Recommended Applications
Configuration Header File
Pyroelectric Sensor
Room occupancy and proximity sensing
N/A*
RE200B-P
API_INIT_06.h
RE200B-P
API_INIT_07.h
RE200B-P
API_INIT_05.h
RE200B-P
180° detection with single pyro Wall mount room lighting control AC light switch replacement Hotel room thermostats
NCL-3B Lens 10mm wall mount array Specification – (60° x 60°) see page 19 Clips on to pyroelectric sensor
Proximity or Entrance Detection Kiosk
Vending 4 beams (X); 2 beams (Y) HVAC 10m range Display counters
NCL-3R Lens 10mm Wall/Ceiling Mount Proximity or Entrance Specification – Array (80° x 30°) Detection see page 22 Clips on to pyroelectric Kiosk sensor Vending 6 beams (X); 2 beams (Y) HVAC 10m range Display counters NCL-9(26) Lens Specification – see page 26
Clip-on 15mm Array (360°)
Room Occupancy and Proximity Sensing
Clips on to pyroelectric sensor
Lighting Control
SBDI46-504AA
HVAC Control 2.25m radius at 2m height Appliance 2.1:1 Floor coverage Kiosk/Display Control diameter to height ratio Vending Power Management Appliance Power Management
Note: *The NCL-11 and EWA 0.3 GI V2 lenses are not currently part of the standard ZMOTION bundled suite or offered in ZMOTION development kits. However, the optimized API settings for this lens are available in the ZMOTION Detection Lens and Pyro Sensor Configuration Guide (WP0018).
PS028609-0213
ZMOTION Lens Selection Guide
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
5
Table 2. ZMOTION Detection and Control Lenses and Pyroelectric Sensors (Continued) Recommended Applications
Configuration Header File
Pyroelectric Sensor
NCL-10IL Lens 10mm Wall/Ceiling Mount Specification – Array (80° x 30°) see page 29 Clips on to pyroelectric sensor
Proximity or Entrance Detection
API_INIT_07.h
RE200B-P
NCL-10S Lens 10mm wall mount (27°) Specification – directional see page 34 Clips on to pyroelectric sensor
Entrance detection
API_INIT_09.h
RE200B-P
API_INIT_0A*
RE200B-P
Part Number
Description
Kiosk
Vending 6 beams (X); 2 beams (Y) HVAC 10m range Display counters
2 beams (X), 1 beam (Y) 10m range NCL-11 Lens Wall mount array 104° Specification – (X), 37° (Y) see page 36 32 detection zones
Kiosk Vending HVAC Display counters Room occupancy and proximity sensing
Consumer electronics and Circuit board mount, black appliance power management rectangular lens Display power manage4 meter range ment TV auto shut-off Keypad motion detector
Note: *The NCL-11 and EWA 0.3 GI V2 lenses are not currently part of the standard ZMOTION bundled suite or offered in ZMOTION development kits. However, the optimized API settings for this lens are available in the ZMOTION Detection Lens and Pyro Sensor Configuration Guide (WP0018).
PS028609-0213
ZMOTION Lens Selection Guide
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
6
Table 3. ZMOTION Intrusion Detection Lenses and Pyroelectric Sensors Part Number
Description
Long Range Array LR 1.2 GI 12 V3 Lens Speci- 42.6 mm x 61.0 mm Flat fication – see Fresnel page 39 30.5 mm (1.2ʺ) focal length
Configuration Header File
Pyroelectric Sensor
API_INIT_10.h
RE200B-P
Wall or ceiling mount cur- API_INIT_11.h tain or vertical barrier security/intrusion motion detector
RE200B-P
Corner/Wall Mount secu- API_INIT_09.h rity/intrusion motion detector
RE200B-P
Typical Applications Wall mount long range corridor/hallway security/ intrusion motion detector
30.5 meter (100') range 3:1 floor coverage diameter to height ratio VB 1.2 GI V1 Lens Specification – see page 40
Vertical Barrier Array 42.6 mm x 61.0 mm Flat Fresnel 30.5 mm (1.2ʺ) focal length 15 meter range, horizontal 7 meter range, vertical
WA 1.2 GI 12 Wide Angle Array (88°) V4 Lens Speci- 42.6 mm x 61.0 mm Flat fication – see Fresnel page 41 30.5 mm (1.2ʺ) focal length 18 meter range
Pet immune detector Wide area security motion detector
Note: *The NCL-11 and EWA 0.3 GI V2 lenses are not currently part of the standard ZMOTION bundled suite or offered in ZMOTION development kits. However, the optimized API settings for this lens are available in the ZMOTION Detection Lens and Pyro Sensor Configuration Guide (WP0018).
ZMOTION Detection and Control Lens Specifications Figures 1 through 27 on the following pages discuss the specifications of the lenses selected for the ZMOTION Detection and Control family of products. To see specifications for lenses used in security and intrusion detection applications, refer to the ZMOTION Intrusion Detection Lens Specifications section on page 38.
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
7
AA 0.9 GI T1 Lens Specification The AA 0.9 GI T1 lens array is optimized for dual element pyroelectric sensors in long range sensing applications. It is normally used with the grooved side facing the pyroelectric detector, and curved at a 0.9 inch (22.9 mm) radius about the sensitive area of the detector. The detector position should be 0.492" (12.5 mm) below the upper edge, and centered left-right. AA 0.9 GI T1 FRONT VIEW: 49.9mm (1.965in)
TOP VIEW: 12.5mm (.492in) 35.6mm (1.400in)
15 m (45ft)
0
88°
15 m (45ft)
SIDE VIEW: 2.1m (6.8ft)
15m (45ft)
Figure 1. The AA 0.9 GI T1 Lens Specification
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
8
CM 0.77 GI V2 Lens Specification The CM 0.77 GI V2 lens is intended for high ceiling-mounted commercial lighting and HVAC applications in which high floor coverage is required. See Figures 2 and 3.
Detector Position
11.7mm (0.46in)
Grooved Side
Notch Radius 1.5mm (0.060in)
19.6mm (0.77in)
15°
Inactive Area
TOP VIEW: 9.1m (30ft)
CL
52.5mm (2.066in)
6.1m (20ft) 7.8mm (0.3in)
CL
3.0m (10ft)
CL
0
3.0m (10ft)
Note: The "beam" pattern obtained depends strongly on the detector used with this array. The pattern shown is intended solely as a general guide.
6.1m (20ft)
9.1m (30ft)
SIDE VIEW: 0
8ft (2.4m) 7.3m (24ft)
4.3m (14ft)
2.4m (8ft)
0.9m 0 0.9m (3ft) (3ft)
2.4m (8ft)
4.3m (14ft)
7.3m (24ft)
Figure 2. CM 0.77 GI V2 Lens Specification: Front View
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
9
9.1m (30ft)
CL
6.1m (20ft)
3.0m (10ft)
CL
0
3.0m (10ft)
6.1m (20ft) Note: The "beam" pattern obtained depends strongly on the detector used with this array. The pattern shown is intended solely as a general guide.
9.1m (30ft)
(For mounting height of 2.4m (8ft))
SIDE VIEW: 0
8ft (2.4m) 10ft (3.0m) 12ft (3.7m)
12.2m (40ft)
9.1m (30ft)
6.1m (20ft)
3.0m (10ft)
0
3.0m (10ft)
6.1m (20ft)
9.1m (30ft)
12.2m (40ft)
Figure 3. CM 0.77 GI V2 Lens Specification: Floor Coverage, Side View
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
10
CM 0.77 GI V3 Lens Specification The CM 0.77 GI V3 lens array is intended for ceiling-mounted applications and is optimized for use with both dual and quad element pyroelectric sensors. The detector mounting flange should be 0.46" (11.7 mm) from the pyroelectric sensor’s element. The angle from the center line to the placement notch is 15 degrees.
FRONT VIEW :
CEILING MOUNT ARRAY
Detector Position
CM 0.77 GI V3
11.7mm (0.46in) 19.6mm (0.77in)
Grooved Side
Notch Radius 1.5mm (0.060in)
TOP VIEW: 4.6m (15ft)
CL 52.5mm (2.066in)
3.0m (10ft)
7.8mm (0.3in)
1.5m (5ft)
CL CL
0
1.5m (5ft)
3.0m (10ft) Note: The "beam" pattern obtained depends strongly on the detector used with this array. The pattern shown is intended solely as a general guide.
4.6m (15ft)
SIDE VIEW: 0
8ft (2.4m) 3.7m (12ft)
2.7m 2.1m 1.5m 0.9m (9ft) (7ft) (5ft) (3ft)
0
0.9m 1.5m 2.1m 2.7m (3ft) (5ft) (7ft) (9ft)
3.7m (12ft)
Figure 4. The CM 0.77 GI V3 Lens Specification, #1 of 2
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
11
g
g
4.6m (15ft)
CL
3.0m (10ft)
1.5m (5ft)
CL
0
1.5m (5ft)
3.0m (10ft) Note: The "beam" pattern obtained depends strongly on the detector used with this array. The pattern shown is intended solely as a general guide.
4.6m (15ft)
SIDE VIEW: 0
8ft (2.4m) 10ft (3.0m) 12ft (3.7m) 6.1m (20ft)
4.6m (15ft)
fresnel technologies inc. 1995
3.0m (10ft)
1.5m (5ft)
0
1.5m (5ft)
3.0m (10ft)
4.6m (15ft)
6.1m (20ft)
101W. MORNINGSIDE DR. FORT WORTH, TX 76110, U. S. A. (817) 926-7474, FAX:(817) 926-7146
Figure 5. The CM 0.77 GI V3 Lens Specification, #2 of 2
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
12
CM 0.77 GI V5 Lens Specification The CM 0.77 GI V5 lens array is intended for ceiling-mounted applications and is optimized for both dual and quad element pyroelectric detectors. The detector mounting flange should be 0.46" (11.7 mm) from the pyroelectric sensor’s element.
FRONT VIEW :
CEILING MOUNT ARRAY
Detector Position
CM 0.77 GI V5
11.68mm (0.46in) 19.56mm (0.77in)
Grooved Side
TOP VIEW:
15°
Notch Radius 1.52mm (0.060in)
4.6m (15ft)
CL 52.5mm (2.066in)
3.0m (10ft)
7.82mm (0.308in)
1.5m (5ft)
CL CL
0
1.5m (5ft)
3.0m (10ft) Note: The "beam" pattern obtained depends strongly on the detector used with this array. The pattern shown is intended solely as a general guide.
4.6m (15ft)
SIDE VIEW: 0
8ft 3.7m (12ft)
2.7m 2.1m 1.5m 0.9m (9ft) (7ft) (5ft) (3ft)
fresnel technologies inc. 2008
0
0.9m 1.5m 2.1m 2.7m (3ft) (5ft) (7ft) (9ft)
3.7m (12ft)
101W. MORNINGSIDE DR. FORT WORTH, TX 76110, U. S. A. (817) 926-7474, FAX:(817) 926-7146
Figure 6. The CM 0.77 GI V3 Lens Specification, #1 of 3
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
13
CEILING MOUNT ARRAY CM 0.77 GI V5
FLOOR COVERAGE: 12.2m (40ft)
(For mounting height of 12.2m (30ft))
CL
(30ft) 9.1m
6.1m (20ft)
(10ft) 3.0m
CL
0
3.0m (10ft)
(20ft) 6.1m
9.1m (30ft)
Note: The "beam" pattern obtained depends strongly on the detector used with this array. The pattern shown is intended solely as a general guide.
(40ft) 12.2m
SIDE VIEW: 0
(20ft) 6.1m
9.1m (30ft)
(40ft) 12.2m 12.2m (40ft) fresnel technologies inc. 2008
9.1m (30ft)
6.1m (20ft)
3.0m (10ft)
0
3.0m (10ft)
6.1m (20ft)
9.1m (30ft)
12.2m (40ft)
101W. MORNINGSIDE DR. FORT WORTH, TX 76110, U. S. A. (817) 926-7474, FAX:(817) 926-7146
Figure 7. The CM 0.77 GI V3 Lens Specification, #2 of 3
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
14
CEILING MOUNT ARRAY CM 0.77 GI V5 FLOOR COVERAGE: 12.2m (40ft)
(For mounting height of 12.2m (30ft), and when a 4 element is used )
CL
(30ft) 9.1m
6.1m (20ft)
(10ft) 3.0m
CL
0
3.0m (10ft)
(20ft) 6.1m
9.1m (30ft)
Note: The "beam" pattern obtained depends strongly on the detector used with this array. The pattern shown is intended solely as a general guide.
(40ft) 12.2m
SIDE VIEW: 0
(20ft) 6.1m
9.1m (30ft)
(40ft) 12.2m 12.2m 9.1m 6.1m 3.0m 3.0m 6.1m 9.1m 12.2m 0 (40ft) (30ft) (20ft) (10ft) (10ft) (20ft) (30ft) (40ft) fresnel technologies inc. 101W. MORNINGSIDE DR. FORT WORTH, TX 76110, U. S. A. (817) 926-7474, FAX:(817) 926-7146 2008
Figure 8. The CM 0.77 GI V3 Lens Specification, #3 of 3
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
15
CWM 0.5 GI V1 Lens Specification The CWM 0.5 GI V1 lens array is intended for both wall and ceiling-mounted applications and is optimized for both dual and quad element pyroelectric detectors. The lens is intended to clip directly into the circuit board over top of the pyroelectric sensor.
FRONT VIEW:
TOP VIEW:
1mm R (0.04in)
9.1m (30ft) 24mm (0.94in) 2mm R (0.08in)
24mm (0.94in)
4.6m (15ft)
5.2mm (0.2in)
TOP VIEW:
180°
0m
14.2mm (0.56in) 12mm (0.47in)
CLIP DETAILS: (Scale 10:1)
4.6m (15ft)
2.5mm (0.1in)
1.7mm (0.065in)
9.1m (30ft)
1. (0. 5mm 06 in)
SIDE VIEW:
(0. 1mm 04 in)
mm ) 3.2 125in (0.
1.2m (4ft) 0m 2.4m (8ft)
4.3m (14ft)
9.1m (30ft)
Figure 9. The CM 0.5 GI V1 Lens Specification: Wall Mount
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
16
FRONT VIEW :
CEILING MOUNT ARRAY
5.2mm (0.2in)
CWM 0.5 GI V1 14.2mm (0.56in)
12mm (0.47in)
TOP VIEW: 4.6m (15ft)
1mm R (0.04in)
CL
24mm (0.94in)
3.0m (10ft)
2mm R (0.08in)
24mm (0.94in) 1.5m (5ft)
CL
0
CLIP DETAILS:
1.5m (5ft)
(Scale 10:1)
2.5mm (0.1in)
3.0m (10ft) 1.7mm (0.065in)
1. (0. 5mm 06 in)
4.6m (15ft) (0. 1mm 04 in)
SIDE VIEW: 0
mm ) 3.2 125in (0.
Note: The "beam" pattern obtained depends strongly on the detector used with this array. The pattern shown is intended solely as a general guide.
8ft 3.7m (12ft)
2.7m 2.1m 1.5m 0.9m (9ft) (7ft) (5ft) (3ft)
0
0.9m 1.5m 2.1m 2.7m (3ft) (5ft) (7ft) (9ft)
3.7m (12ft)
fresnel technologies inc.
Figure 10. 2009 The CM 0.5 GI V1 Lens Specification: Ceiling Mount, #1 of 2
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
17
(
g
g
(
))
9.1m (30ft)
CL
6.1m (20ft)
3.0m (10ft)
CL
0
3.0m (10ft)
6.1m (20ft)
9.1m (30ft)
Note: The "beam" pattern obtained depends strongly on the detector used with this array. The pattern shown is intended solely as a general guide.
SIDE VIEW: 0
(15ft) 4.6 m
(25ft) 7.6 m 9.1m (30ft)
6.1m (20ft)
3.0m (10ft)
0
3.0m (10ft)
6.1m (20ft)
9.1m (30ft)
fresnel technologies inc.
Figure 11. 2009 The CM 0.5 GI V1 Lens Specification: Ceiling Mount, #2 of 2
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
18
EWA 0.3 GI V2 Lens Specification The EWA 0.3 GI V2 lens is intended for wall-mounted room occupancy and proximity sensing applications in which an extra-wide sensing angle is required. See Figure 12. Sensitive Element
1.0" (25.4mm)
.30" (7.6mm)
4.6 m 28.4mm (1.12in) 22.4mm (0.88in) 13.8mm 7.6mm (0.54in) (0.3in)
0.07" 0.08" 0.09" 0.2"
TOP VIEW: ACTUALSIZE
4.6 m
SIDE VIEW:
4.6m
Figure 12. The EWA 0.3 GI V2 Lens Specification, Dimensions
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
19
NCL-3B Lens Specification The NCL-3B lens is intended for wall-mounted entrance and proximity-sensing applications.
Figure 13. The NCL-3B Lens Dimensions
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
20
Figure 14. The NCL-3B Lens Specification, X Axis
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
21
Figure 15. The NCL-3B Lens Specification, Y Axis
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
22
NCL-3R Lens Specification The NCL-3R lens is intended for wall-mounted entrance and proximity-sensing applications. This lens features two orientations, Tab A and Tab B, that can be used with the pyroelectric sensor to provide different beam patterns. Figures 16 through 19.
ȭ ȭ
7$% GLUHFWLRQ $
5
5
7$% GLUHFWLRQ %
ȭ ȭ
7ROHUDQFH
Figure 16. The NCL-3R Lens Specification, Dimensions
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
23
),(/' 2) 9,(:
'8$/ 7<3( (/(0(17 6,=( *DSPP
7$% GLUHFWLRQ $
P
$
㺽
;
P
;
P
P
P
<
;
<
% 㺽 㺽
㺽 㺽 <
P
<
P
㺽
P
㺽
;
㺽
P
P
P
P
P
P
'LVWDQFH㸸 P >'HWHFWLRQ $UHD LQ IURQW RI P@
81,7
>P@
Figure 17. The NCL-3R Dual Element Lens Specification, Tab Direction A, X Axis
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
24
),(/' 2) 9,(:
'8$/ 7<3( (/(0(17 6,=( *DSPP
7$% GLUHFWLRQ %
P
㺽
$
P
<
P
<
P
P
;
; ;
% 㺽 㺽
㺽 㺽 <
P
<
P
㺽
P 㺽
;
㺽
P
P
P
P
P
P
'LVWDQFH㸸 P >'HWHFWLRQ $UHD LQ IURQW RI P@
81,7
>P@
Figure 18. The NCL-3R Dual Element Lens Specification, Tab Direction A, Y Axis
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
25
),(/' 2) 9,(:
(/(0(17 7<3( (/(0(17 6,=( *DSPP
7$% GLUHFWLRQ $
P
㺽
$
;
P
;
P
P
P
<
;
<
% 㺽
㺽
㺽 㺽
<
P
<
P
㺽
P
㺽
;
㺽
P
P
P
P
P
P
Figure 19. The NCL-3R Quad Element Lens Specification, Tab Direction A, X Axis
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
26
NCL-9(26) Lens Specification The NCL-9(26) lens is intended for ceiling-mounted and other general purpose motion sensing applications. It is optimized for both dual and quad element pyroelectric sensors.
Figure 20. The NCL-9(26) Lens Specification, #1 of 3
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
27
Figure 21. The NCL-9(26) Lens Specification, #2 of 3
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
28
Figure 22. The NCL-9(26) Lens Specification, #3 of 3
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
29
NCL-10IL Lens Specification The NCL-10IL lens is intended for wall-mounted entrance and proximity-sensing applications. This lens features two orientations, Tab A and Tab B, that can be used with the pyroelectric sensor to provide different beam patterns. Refer to Figures 24 and 25 for the Tab A beam patterns and to Figures 26 and 27 for the Tab B beam patterns.
ȭ ȭ
7$% GLUHFWLRQ $
5
5
7$% GLUHFWLRQ %
ȭ ȭ
Figure 23. The NCL-10IL Lens Specification, Dimensions
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
30
'8$/ (/(0(17 7<3( (/(0(17 6,=( *DSPP 7$% GLUHFWLRQ $ 㹖 D[LV
7$% GLUHFWLRQ $
㹖
7$% GLUHFWLRQ % 㹗
㺽
㺽
㹖
Figure 24. The NCL-10IL Lens Specification, Tab Direction A, X Axis
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
31
(/(0(17 7<3( (/(0(17 6,=( *DSPP
7$% GLUHFWLRQ $ 㹗 D[LV
7$% GLUHFWLRQ $ 㹖
7$% GLUHFWLRQ %
㹗
㹗
Figure 25. The NCL-10IL Lens Specification, Tab Direction A, Y Axis
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
32
(/(0(17 7<3( (/(0(17 6,=(
*DSPP
7$% GLUHFWLRQ % 㹖 D[LV
7$% GLUHFWLRQ $ 㹗 7$% GLUHFWLRQ % 㹖
㹖
Figure 26. The NCL-10IL Lens Specification, Tab Direction B, X Axis
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
33
(/(0(17 7<3( (/(0(17 6,=( *DSPP
7$% GLUHFWLRQ % 㹗 D[LV
7$% GLUHFWLRQ $
㹗 7$% GLUHFWLRQ %
㹖
㺽
㺽
㹗
Figure 27. The NCL-10IL Lens Specification, Tab Direction B, Y Axis
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
34
NCL-10S Lens Specification The NCL-10S lens is intended for wall-mounted entrance detection applications wherein directional recognition is required. See Figures 28 and 29. ',0(16,21
81,7
>PP@
/HQV DUHDȭ 7H[WXULQJ DUHD
$
$
ȭ
ȭ
࠙723 9,(:ࠚ
5 5
࠙6,'( 9,(:ࠚ
7$% GLUHFWLRQ $
㺽
ȭ
ȭ ȭ
7$% GLUHFWLRQ %
࠙%$6( 9,(:ࠚ
࠙$$ ࠚ
$
$
5
7ROHUDQFH
Figure 28. The NCL-10S Lens Specification, Dimensions
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
35
),(/' 2) 9,(:
6,1*/( (/(0(17 7<3( (/(0(17 6,=( ȭPP 㹖㸪㹗 D[LV
㹖
㹗
81,7
>P@
Figure 29. The NCL-10S Dual Element Lens Specification, X/Y Axes
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
36
NCL-11 Lens Specification The NCL-11 lens is intended for wall-mounted room occupancy and proximity sensing applications with 32 detection zones. See Figures 30 and 31.
Figure 30. The NCL-11 Lens Specification, Dimensions
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
37
Figure 31. The NCL-11 Detection Area, X/Y Axes
PS028609-0213
ZMOTION Detection and Control Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
38
ZMOTION Intrusion Detection Lens Specifications Figures 34 through 33 provide the zone patterns and mechanical dimensions for the ZMOTION Intrusion Detection family of products. Recommended placement of the pyroelectric sensor is provided with the detector and lens inclined downward at an angle of 12 degrees. If you wish to use a tilt angle other than 12 degrees while maintaining the specified zone patterns, move the pyroelectric sensor up by 0.021" (0.53 mm) for each degree less than 12 degrees, or down by the same amount for each degree greater than 12 degrees. The WA 1.2 GI 12 V4, LR 1.2 GI 12 V3 and VB 1.2 GI V1 lenses can be interchanged in the same end product without modifications to the placement or angle of the lens. These lenses may also be used in nonintrusion applications. For additional lenses that do not require security/intrusion detection capabilities, refer to the ZMOTION Detection and Control Lens Specifications section on page 6.
PS028609-0213
ZMOTION Intrusion Detection Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
39
LR 1.2 GI 12 V3 Lens Specification The LR 1.2 GI 12 V3 lens array is optimized for dual-element pyroelectric sensors in long-range corridor security applications. It is normally used with the grooved side facing the pyroelectric detector, and curved at a 1.2 inch (30.5 mm) radius about the sensitive area of the detector. The detector and the lens array should be inclined downward at an angle of 12 degrees. If you wish to use a tilt angle other than 12 degrees while maintaining the specified zone pattern, move the pyroelectric sensor up by 0.021" (0.53 mm) for each degree less than 12 degrees, or down by the same amount for each degree greater than 12 degrees. The detector position should be 0.812" (20.6 mm) below the upper edge, and centered left-to-right. FRONT VIEW:
20.6mm (0.81in) 42.6mm (1.675in)
61mm (2.4in)
TOP VIEW:
77° 5m (16ft)
21.5°
2.5m (8ft)
14°
29°
6.5°
CL
0 2.5m (8ft) 5.0m (16ft)
SIDE VIEW:
2.1m (6.8ft) 1m (3ft)
2.2m (7ft)
3m (10ft)
10.7m (35ft)
30.5m (100ft)
18.3m (60ft)
Figure 32. LR 1.2 GI 12 V3 Lens Specification
PS028609-0213
ZMOTION Intrusion Detection Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
40
VB 1.2 GI V1 Lens Specification The VB 1.2 GI V1 lens array is optimized for dual-element pyroelectric sensors in vertical barrier or curtain-type security applications. It is normally used with the grooved side facing the pyroelectric detector, and curved at a 1.2 inch (30.5 mm) radius about the sensitive area of the detector. The detector and the lens array should be inclined downward at an angle of 12 degrees. If you wish to use a tilt angle other than 12 degrees while maintaining the specified zone pattern, move the pyroelectric sensor up by 0.021" (0.53mm) for each degree less than 12 degrees, or down by the same amount for each degree greater than 12 degrees. The detector position should be 0.812" (20.6 mm) below the upper edge, and centered left-to-right.
Figure 33. VB 1.2 GI V1 Lens Specification
PS028609-0213
ZMOTION Intrusion Detection Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
41
WA 1.2 GI 12 V4 Lens Specification The WA 1.2 GI 12 V4 lens array is optimized for dual-element pyroelectric sensors in large-area security applications. It is normally used with the grooved side facing the pyroelectric detector, and curved at a 1.2 inch (30.5 mm) radius about the sensitive area of the detector. The detector and the lens array should be inclined downward at an angle of 12 degrees. If you wish to use a tilt angle other than 12 degrees while maintaining the specified zone pattern, move the pyroelectric sensor up by 0.021" (0.53 mm) for each degree less than 12 degrees, or down by the same amount for each degree greater than 12 degrees. The detector position should be 0.812" (20.6 mm) below the upper edge, and centered leftto-right. FRONT VIEW:
20.6mm (0.81in) 42.6mm (1.675in)
TOP VIEW: 61mm (2.4in)
10m (33ft)
5m (16ft)
0
88.2°
5m (16ft)
10m (33ft)
SIDE VIEW: 2.1m (6.8ft) 1.7m 3.7m (6ft) (12ft)
7m (23ft)
15.6m (51ft)
18m (60ft)
Figure 34. WA 1.2 GI 12 V4 Lens Specification
PS028609-0213
ZMOTION Intrusion Detection Lens Specifications
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
42
Related Documents Additional information about the ZMOTION Families of Motion Detection MCUs can be found in the following documents, which are available from the Zilog website at www.zilog.com. Document Number
Description
PB0225
ZMOTION Detection and Control Family Product Brief
PS0285
ZMOTION Detection and Control Family Product Specification
PB0230
ZMOTION Intrusion Detection Product Brief
PS0288
ZMOTION Intrusion Detection Product Specification
PS0228
Z8 Encore! XP® F082A Series Product Specification
AN0307
ZMOTION Detection Module Application Walkthrough
AN0309
ZMOTION High Brightness White LED Lighting Application Note
WP0017
A New PIR Motion Detection Architecture White Paper
WP0018
ZMOTION Detection Lens and Pyro Sensor Configuration Guide
Other ZMOTION Family Products
PS028609-0213
PB0223
ZMOTION Detection Module Product Brief
PS0284
ZMOTION Detection Module Product Specification
Related Documents
ZMOTION™ Lens and Pyroelectric Sensor Product Specification
43
Customer Support To share comments, get your technical questions answered, or report issues you may be experiencing with our products, please visit Zilog’s Technical Support page at http://support.zilog.com. To learn more about this product, find additional documentation, or to discover other facets about Zilog product offerings, please visit the Zilog Knowledge Base at http:// zilog.com/kb or consider participating in the Zilog Forum at http://zilog.com/forum. This publication is subject to replacement by a later edition. To determine whether a later edition exists, please visit the Zilog website at http://www.zilog.com.
PS028609-0213
Customer Support
