Transcript
ＩＭＰＡＣＴ ＭＩＣＲＯ ＰＲＩＮＴＥＲ ＭＰＴ－２６２ⅡＡ
ＴＥＣＨＮＩＣＡＬ ＭＡＮＵＡＬ
ＮＡＤＡ ＥＬＥＣＴＲＯＮＩＣＳ， ＬＴＤ． Ｖ１．３
０００３１３
ＣＯＮＴＥＮＴＳ
GENERAL
‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
１
FEATURES
‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
１
ORDERING INFORMATIONS ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
１
GENERAL SPECIFICATIONS ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
２
PRINT COLUMN ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
２
CHARACTER SIZE ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
２
OEM CHARACTERS ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
２
GRAPHICS ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
２
INTERFACE ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
２
POWER ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
２
CONDITIONS ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
２
RELIABILTY ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
３
PAPER ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
３
INK RIBBON CASETTE ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
３
WEIGHT ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
３
ATTACHMENT ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
３
PANEL SWITCH ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
４
TEST PRINT ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
４
HEX DUMP ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
４
FRONT PANEL ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
５
REAR PANEL ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
６
HOW TO CHANGE ROLL PAPER ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
７
HOW TO CHANGE RIBBON CASETTE ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
８
CAUTIONS ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
９
MAINTENANCE AND CLEANING ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
１０
WARNINGS ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
１０
ENVIROMENTS ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
１０
GURANTEE ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥
１０
ＧＥＮＥＲＡＬ ２６２ⅡＡ series are impact journal printer, with JIS Chinese (KANJI) characters inside, OEM and graphic image, red and black printouts.
ＦＥＡＴＵＲＥＳ ＊ JIS ⅠⅡ KANJI 16×16 dots font. ＊ SHIFT JIS code KANJI selectable. ＊ OEM characters 16×16 dot font. ＊ Graphics printable. ＊ 3 varieties of ANK 184 characters font.
ＯＲＤＥＲＩＮＧ ＩＮＦＯＲＭＡＴＩＯＮＳ ＭＰＴ－２６２ⅡＡ－Ｃ－３５ Ｋ Ｐ Ｂ Adopted model Interface KANJI optionals Column printable Cutter optionals Model MODEL
MPT-262ⅡA ; desk-top type
CUTTER optionals
None: wo / cutter standard C: w / cutter
COLUMN printable
Set by DIP SW or selectable by command 35 ; 5×7 dot font 42 ; 7×7 dot font (half dot)
KANJI optionals
None : wo / KANJI standard K : KANJI set
INTERFACE default set
P : Parallel CENTRONICS R : Serial RS232C
Adopted model
None : standard ; DIP selectable to old model Ａ: MP-210 compatible B : PC-9801 type
1
ＧＥＮＥＲＡＬ ＳＰＥＣＩＦＩＣＡＴＩＯＮＳ 1：printing method 2：dots per line 3：printing rate
Shuttle dot matrix 210 dots / line 2.3 line / sec (5×7 dot font) print only
ＰＲＩＮＴ ＣＯＬＵＭＮ 1：ANK 5×7 font 2：ANK 7×7 half font 3：ANK 8×16 font 4：KANJI 16×16 full 5：KANJI 16×16 shrank
35 col. 42 26 13 26
ＣＨＡＲＡＣＴＥＲ ＳＩＺＥ 1：ANK 184
2：KANJI
ＯＥＭ ＣＨＲＡＣＴＥＲＳ
ＧＲＡＰＨＩＣＳ
width × height 1.6 × 2.9 mm 1.3 × 2.9 mm 2.2 × 5.8 mm 5.0 × 6.6 mm 2.2 × 6.6 mm
5×7 7×7 8×16 16×16 full 16×16 shrank
16 blocks
16×16
Data number
4k byte
ＩＮＴＥＲＦＡＣＥ
RS232C / CENTRONICS selectable when order
ＰＯＷＥＲ
85 to 132V AC, 50 / 60Hz 60W operational 7W idling
ＣＯＮＤＩＴＴＯＮＳ 1：operation 2：stock
0℃ to +50℃ ; 30% to 90% non-condensing －20℃ to +70 ; 5% to 95% non-condensing
2
ＲＥＬＩＡＢＩＬＩＴＹ 1：head life 2：MOBF 3：cutter life
100 million strokes / a pin 1.5 million lines MCBF 0.2 million full-cutting
ＰＡＰＥＲ － ｎｏｍａｌ ｐａｐｅｒ 1：roll paper 2：fan-fold 3：paper thick 4：paper weight 5：P / N paper
76mm × 60 × 35m ( width × dia × length ) 76mm × 5 inch × 35m (width × height × length ) 0.06 to 0.85mm 52.4g / ㎡ to 64g / ㎡ NR-760 roll paper
ＩＮＫ ＲＩＢＢＯＮ ＣＡＳＥＴＴＥ ERC-23 ( red / black dual colors), 3 / 4 millions characters life
ＷＥＩＧＨＴ
3.9 ㎏
ＡＴＴＡＣＨＭＥＮＴ 1：ribbon cassette 2：roll paper 3：roll shaft 4：fuse 5：connecter
ERC-23 NR-760 S-7 2A 100V AC 57-30360 CENTRONICS or DB-25P RS232C
1 pc. 1 roll 1 pc. 2 pcs. 1 pc. 1 pc.
3
ＰＡＮＥＬ ＳＷＩＴＣＨ 1. FEED SWITCH Paper is fed by this switch. Effective in both mode of select or disselect. Set paper without paper jamming, or OFF power and take off paper by pinsette. 2. SELECT SWITCH This switch can drive printer off-line by manual. If return to on-line, depress this switch again. Or there is no paper, or printer is out of order.
ＴＥＳＴ ＰＲＩＮＴ Operation ： ON the power depressing FEED switch. Functions ： checking mechanics-unit and inner logic, confirming DIP selection.
ＨＥＸ ＤＵＭＰ Operation ： ON the paper by depressing SELECT switch. Functions ： Printout HEX code data by bufferful mode by depressing SELECT SWITCH, confirming received data.
4
ＦＲＯＮＴ ＰＡＮＥＬ
1
2
3
ＰＷ
ＳＥＬ
4
5
1. PAPER OUT Paper shall be fed from this position. 2. SELECT SWITCH Switchover SELECT/DISSELECT mode by depressing this switch, and DIP-SW 1-4 OFF. DISSELECT mode, green LED off and will not received data. 3. POWER LED (red) Blinking when power is ON. 4.SELECT LED (green) On this LED is SELECT mode, OFF this LED is DISSELECT mode. DISSELECT automatically by paper-end. 5.FEED SWITCH Paper feed switch, anytime while SELECT or DESSELECT mode. Remark：RED and GREEN LED blinks while MECHANICS ERROR.
5
ＲＥＡＲ ＰＡＮＥＬ
1
2
3
1. SERIAL I/O CONNECTOR RS232C connector 2. PARALLEL I/O CONNECTOR CENTRONICS connector 3. GROUND EARTH Cabinet earth plug. 4. FUSE V AC power line, 2A fuse only. 5. POWER 85 – 132V AC supplyable.
6
4
5
ＨＯＷ ＴＯ ＣＨＡＮＧＥ ＲＯＬＬ ＰＡＰＥＲ Open top cover 1 then 2 as below figure, insert shaft into roll, then set to paper-holder carefully.
1
2
Insert paper and feed by FEED SWITCH, then pass through paper-out of top cover. Completion of setting , change LED from RED to GREEN by SELECT SWITCH.
7
ＨＯＷ ＴＯ ＣＨＡＮＧＥ ＲＩＢＢＯＮ ＣＡＳＥＴＴＥ Open top cover 1 then 2, pull up the edge as figure below.
2
1
Stretch ribbon tape by winding knob as figure below.
Set cassette correctly as figure below. Stretch tape by manual or by FEED switch.
8
ＣＡＵＴＴＩＯＮＳ 1. Do not print without paper and ribbon cassette. 2. ON the power, it will return head to default automatically. 3. OFF the power, then take off jammed paper by pin carefully. 4. Roll paper must be used our recommended only. 5. Never ON-OFF power repeatedly at short interval. 6. Do not bundle printer-line to other cables. It may be damaged by noises. 7. Clean the printer regularly. 8. Do not set at the place of iron-dusty or dusty. 9. In use of fan-hold paper, it will not print correctly at the position of 8mm from the sewing-line, sometimes. 10.TEST PRINTING by depress FEED SWITCH and ON the power, which shows contents selected by DIP SWITCH. 11.CUTTER mode: drive cutter by FEED SWITCH at disselect mode, then cut automatically. 12.Lever will be up to arrow direction as figure, at ribbon and paper change time, not to bend Lever. Or dual printing is out of order. 13.Mix-printing of character available. However, each character command shall be set newly one by one, or it will cause printing trouble.
9
ＭＡＩＮＴＥＮＡＮＣＥ ＡＮＤ ＣＬＥＡＮＩＮＧ Mechanics and its unit shall be wiped by alcohol or benjin. Never use thinner, torikuren, keton which will damage plastics. Wipe dust by vacuum cleaner. Regular checking : every 3 months or half million .lines printing.
ＷＡＲＮＩＮＧＳ 1.Paper jam: never drive jammed paper off, which break mechanics. 2.RED/GREEN LED blinking: OFF and ON power at 5 seconds interval.
ＥＮＶＩＲＯＭＥＮＴＳ 1.Do not set at the place of iron-dusty or dusty, where it causes damages of mechanism, gears, etc,. 2.Do not bundle signal line cable with hi-power cable, as V AC cable, to escape from noise trouble. 3.Be care of circumstance, especially chemical conditions. Mechanics has touch point inside, some chemical as SILICONE will cause troubleness. 4.GROUND line shall be set without fail, to escape from hi-statistic voltage on printer. 5.In case of hi-condensity, it will be operated after the clearance of condensing.
ＧＵＲＡＮＴＥＥ NADA’s obligations and liabilities under the foregoing grantee are limited to repair or replacement of the products without charge, provided it is mailed prepaid or air freight prepaid to NADA ELECTRONICS, Ltd., Overseas Division, 4-5-11, Shiba, Minato-ku, Tokyo 108 JAPAN. A charge is made for repairing after the expiration of grantee. NADA ELECTRONICS, Ltd. grantees the model of type printer series against the defects in material and workmanship for a period of 60 days from the date of shipment to end customer directly. This is a limited grantee to its terms. This grantee is void if the products has been altered, misused, taken apart or otherwise abused. This grantee is effective to the customer who bought product directly from us. Other customers or buyers shall ask for grantee terms to those who sell products , , , agents, distributors, importers, etc, . In no event shall NADA be liable for claims based upon breach of express or implied grantee or negligence or any other damages whether direct, immediate, foreseeable, consequential or special or for any expenses incurred by reason of the use or misuse, sale or fabrications of products which do not confirm to the terms and conditions of this contract.
10
