Transcript
22-Pin Connector
ID Switch
Reserved
ISP Connector (for FW upgrade)
E
F
G
CD (Contains all operation manuals)
•
D
Quick Guide (Contains general Dome Camera setups information)
•
None
Lubricant (For cover installation)
•
Communication Switch
Security Torx
•
C
M3/M5 Standard/Security Screws (For fixing the outdoor Dome Camera’s cover/top holder)
•
Camera Control Protocol Switch
Waterproof Rubber
•
B
Data Cable (AC 24V)
•
A
Dome Cover
•
Switch Definition
Dome Camera
•
Standard Package
Line Lock Factory Default Reset Camera Upgrade
SW 4 SW 5 SW 6
Full-duplex
RS-485 Setting Half-duplex
0 1 2 3 4 5 6 7 8 9 10
ID No.
Manual.
SW-1 OFF ON OFF ON OFF ON OFF ON OFF ON OFF
SW-2 OFF OFF ON ON OFF OFF ON ON OFF OFF ON
SW-3 OFF OFF OFF OFF ON ON ON ON OFF OFF OFF
SW-4 OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON
Switching Setting SW-5 SW-6 SW-7 OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
SW-8 OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
SW-9 OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
SW-10 OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
1
0~10 are listed in the table below. For complete ID setups, please refer to the Mini Speed Dome Camera’s User
and SW-3 at “ON” position and the rest at “OFF” position as shown below. Dip switch configuration for ID No.
Camera’s back plate. If the Dome Camera’s ID number is 6, for instance, the ID switch should be set with SW-2
same network. The camera’s ID can be setup using the 10-bit ID dip switch, which is located on the Dome
Please assign an ID number to a Speed Dome Camera if there is more than one Speed Dome Camera in the
Camera ID Setup
Termination
RS-485 Setting
SW 3
SW 2
SW 1
plate. Communication Switch
The table below shows the definition of each switch of the Communication Switch on the Dome Camera’s back
operate the Dome Camera, please read its Installation Guide and User Manual thoroughly.
System Configuration
Communication Switch Setting
information on the Dome Camera’s basic settings and operation. Before attempting to connect, configure and
00P5H6100ZXSEA3
This quick guide is a reference for users to install and operate the Dome Camera quickly, and thus only provides
Mini Speed Dome Camera Quick Guide
VCL Pelco D Pelco P Chiper Philips DSCP AD422 DM P Pelco D Pelco D Pelco P Pelco P JVC Kalatel-485 Kalatel-422 Panasonic
00 01 02 04 05 07 08 09 11 12 13 14 15 21 22 23
9600 2400 4800 9600 9600 9600 4800 9600 4800 9600 2400 9600 9600 9600 4800 19200
Baud Rate SW-1 OFF ON OFF OFF ON ON OFF ON ON OFF ON OFF ON ON OFF ON
SW-2 OFF OFF ON OFF OFF ON OFF OFF ON OFF OFF ON ON OFF ON ON
Switch Setting SW-3 SW-4 SW-5 OFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF ON OFF OFF ON OFF OFF OFF ON OFF OFF ON OFF OFF ON OFF ON ON OFF ON ON OFF ON ON OFF ON ON OFF ON OFF ON ON OFF ON ON OFF ON SW-6 OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
terminal block.
2. When wiring the AC 24V power cable, make sure the Ground wire is inserted into the mid-pin of the
1. Input electricity to the unit is at tolerance of AC 24V ± 10%.
NOTE:
and definition of each connector before wiring.
The Dome Camera is equipped with one AC 24V Data Cable. Please refer to the illustration below for function
Data Cable and Connector Definition
Protocol
Switch No.
“ON” position and the rest to “OFF” position as shown below.
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
Definition AC 24-1/DC (＋) ALM NC AC 24-2/DC (－) ALM NO FG ALM COM T+ RTR+ ISOG ALM-1 ALM-3 ALM-2 ALM-4 ALM-5 ALM-6 ALM-7 ALM-8 ALM GND VGND Video 20AWG
24AWG
20AWG/18AWG
20AWG/18AWG
Cable 20AWG/18AWG
2
Cable.
If you select protocol Pelco D, which is of switch No. 01 and baud rate 2400, for instance, please set SW-1 to
When cabling, please refer to the table below for pin definition of the Data Cable’s 22-pin connector on the Data
22-Pin Connector Definition
device; then adjust the protocol switch on the Dome Camera’s back plate by setting the 6-bit protocol dip switch.
__
Refer to the table below and select one set of protocol and baud rate you would like to use basing on the control
Camera Protocol Setup
