600 Size Airwolf (cn4040/cn4040a)

Transcript

AIRWOLF 50 ( CN4040 / CN4040A ) INSTALLATION MANUAL ENGINE SIZE:50 AIR WOLF INSTALLATION MANUAL 1 C E D CUT MESH ACCORDING TO THE TEMPLATE PROVIDED. GLUE MESH WITH CA INSIDE FUSELAGE AND HATCH. B NOTICE: USE EPOXY UNLESS STATED. SAND INSIDE FUSELAGE WITH #180 SANDING PAPER BEFORE PARTS GLUING IN PLACE. 2 CUT 2.5x11 MM SLOTS IN THE HATCH. GLUE THE PLASTIC MOUNTING BRACKETS INSIDE. A GLUE 3x10x10MM PLYWOOD AND 3 MM ALUM. POLES FOR HATCH AND FUSELAGE ALIGNMENT. 3 4 GLUE 3x16 MM PLYWOOD IN THE FUSELAGE. DRILL HOLES WHICH ALIGNED TO THE ALUM. POLES AS IN DIAGRAM. MOUNT THE SLOTTED PLASTIC PLATES WITH 1.4x4 MM FLAT HEAD TAPPING SCREWS. 5 6 GLUE EXHAUST AND NOZZLES ON FUSELAGE. GLUE INTAKE INSIDE FUSELAGE. 8 7 GLUE PLYWOOD JOINER INSIDE FUSELAGE. GLUE SLOTTED BALSA AND VERTICAL FINS IN HORIZONTAL STAB. AS SHOWN. P.1 AIR WOLF INSTALLATION MANUAL 9 ENGINE SIZE:50 10 90 GLUE AND ALIGN HORIZONTAL STABS. 11 90 ALIGN HORIZONTAL STABS. TO FUSELAGE AS SHOWN. 12 MOUNT TAIL HATCH WITH M3x6 ROUND HEAD TAPPING SCREW. GLUE 1.5x10x10 MM PLYWOOD. 14 13 GLUE CLEAR LIGHT, ALUM. HOLDER AND STEEL WIRE IN THE TAIL FIN. 15 MOUNT THE VERTICAL FIN WITH M3x16 ROUND SOCKET HEAD SCREWS, 3x8x0.7 WASHER AND LOCKNUTS. 16 GLUE RED LIGHT ON TOP OF HATCH AND BOTTOM OF FUSELAGE. GLUE GUN IN POSITION AS SHOWN. P.2 AIR WOLF ENGINE SIZE:50 INSTALLATION OF RETRACTABLE LANDING GEAR 1 E. RING CUT AWAY SHADED PORTION 2 BALL LINK M2 x 36 PUSH ROD ALUM. BUSHING M3 x 10 WASHER HEAD SCREW NOSE GEAR SERVO TRAY 40 MM WHEEL MOUNT THE SERVO TRAY WITH M3x10 SOCKET HEAD SCREW & 3 x 8 x 0.7 WASHER 4 3 OPTIONAL PARTS LANDING GEAR WIRE PART NO. FK 9651 OPTIONAL PARTS RETRACT MECHANISM PART NO. FK 9601 E. RING 5 6 ALUM. BUSHING CUT AWAY SHADED PORTION BALL LINK M2 x 36 PUSH ROD M3 x 10 WASHER HEAD SCREW MAIN GEAR SERVO TRAY 45 MM WHEEL 7 8 MOUNT LANDING GEARS WITH M2.6 x 10 FLAT HEAD SCREW MOUNT THE SERVO TRAY WITH M3x10 SOCKET HEAD SCREW & 3 x 8 x 0.7 WASHER P.3 AIR WOLF ENGINE SIZE:50 INSTALLATION OF CENTURY SCALE SE MECHANISM 1 2 CENTURY SCALE SE 12 MM 143 MM 24 MM 56 MM 76 MM 48 MM CUT VENTILATING HOLE AND MECHANISM MOUNTING HOLES (3.5 MM) AS SHOWN. 3 MOUNTING MECHANISM IN FUSELAGE WITH SHAPED HARDWOOD IN PLACE. 4 10x50 MM PLYWOOD LOCATION (INSIDE FUSELAGE) GLUE 10x50 MM PLYWOOD INSIDE FUSELAGE. MOUNT ALUM. PLATE WITH M3x10 FLAT HEAD SCREW AND LOCKNUT 5 CUT AWAY MARKED PORTION FOR SWATCH PLATE. CUT HOLE FOR STARTING PROBE. 6 39 MM CUT TAIL PORTION FOR GEAR-BOX. 7 INSERT TAIL BOOM INTO SPONGE RING CUT TAIL HATCH FOR GEAR-BOX AS SHOWN. 8 35 MM SPONGE RING LOCATION P.4 AIR WOLF ENGINE SIZE:50 INSTALLATION OF HIROBO SCEADU MECHANISM 1 HIROBO SCEADU 12 MM 2 42 MM 14.5 MM 72 MM 50 MM 12 MM CROSS SECTION 200 MM CUT VENTILATING HOLE AND MECHANISM MOUNTING HOLES (3.5 MM) AS SHOWN. 3 MOUNT THE MECHANISM IN FUSELAGE WITH SANDED MOUNTING PLATE INVERTED. 5 CUT AWAY MARKED PORTION FOR SWATCH PLATE. CUT HOLE FOR STARTING PROBE. 7 SAND AWAY SHADED AREA ON PLYWOOD MOUNTING PLATE AS SHOWN. 4 10x50 MM PLYWOOD LOCATION (INSIDE FUSELAGE) GLUE 10x50 MM PLYWOOD INSIDE FUSELAGE MOUNTING ALUM. PLATE WITH M3x10 FLAT HEAD SCREW AND LOCKNUT. 6 52 MM CUT TAIL HATCH FOR GEAR-BOX AS SHOWN. 8 40 MM SPONGE RING LOCATION INSERT TAIL BOOM INTO SPONGE RING P.5 P.5 AIR WOLF ENGINE SIZE:50 INSTALLATION OF THUNDER TIGER RAPTOR MECHANISM 1 2 THUNDER TIGER RAPTOR 19.5 MM 183 MM 14 MM 60 MM 45 MM 45 MM 20 MM CUT VENTILATING HOLE AND MECHANISM MOUNTING HOLES (3.5 MM) AS SHOWN. 3 MOUNTING MECHANISM IN FUSELAGE WITH SHAPED HARDWOOD IN PLACE. 4 10x50 MM PLYWOOD LOCATION (INSIDE FUSELAGE) GLUE 10x50 MM PLYWOOD INSIDE FUSELAGE. MOUNT ALUM. PLATE WITH M3x10 FLAT HEAD SCREW AND LOCKNUT 5 CUT AWAY MARKED PORTION FOR SWATCH PLATE. CUT HOLE FOR STARTING PROBE. 6 14 CUT TAIL PORTION FOR GEAR-BOX. 7 28 (MM) CUT TAIL HATCH FOR GEAR-BOX AS SHOWN. 8 60 MM SPONGE RING LOCATION INSERT TAIL BOOM INTO SPONGE RING P.6 MESH TEMPLATE (SCALE 1:1) FOR 222 (50) / AIR WOLF (50) B A C E D D E C A B P.7