Transcript
QUICKSTART “BASIC” GUIDELINES FOR MODEL 115 VAC 6002 - FOR A GATE UP TO 14 FEET, 500LBS AND “OPENING TO THE INSIDE”
Clevis Pins
(Actuator Cover Off)
Rear Bracket
Arm in “Open to the Inside” Position
7” 7”
90°
3 Screws ONLY
Limit
lim
it n
H I
(Actuator Cover On)
im n 3 L lo Dw S
A
4
Top
1 2 3 4 5 6 7
G
Coaxial Cable Antenna Kit P/N 1514-073 (Sold separately)
D
J
Bottom
Loops Conduit
Power Conduit
Coaxial Cable Antenna (Not supplied)
G
E Do not connect the battery to the circuit board until power is needed to test the actuator arm.
AC Power Switch
5
6
#8 - #11 Shadow Loop Output 7 8 9 10 11 12 13 14 15 16 17 18 19 20
6. Green 7. Green/Yellow
N.O.
2 3 4
Actuator Cable 1. Brown SINGLE/PRIMARY 2. Blue Actuator Cable 3. Orange Circuit Board 4. Red 5. Yellow Connection
Copyright 2015 DoorKing, Inc. All rights reserved.
115 VAC Connection
4302
Loop Jumper
C
Mounting Hole
Loop Wires
F
RED
Coaxial Cable Antenna
Actuator Cable
CAUTION
BOX MUST BE DANGER CONTROL PROPERLY GROUNDED!!
RED 24V
1
Middle
Battery Connection
Relay must be set to N.O. for shadow loop.
H
Actuator arm and brackets MUST be level!
E
BLK 115V WHT
Do not install the actuator arm in fully extended (Bottomed out) position. This will damage the arm (See Actuator Arm and Control Box Mounting manual for more information).
Battery Plug
Receiver Manual (available from www.dkaccess.com) for more information on radio receivers and antenna installation. See reverse side for wiring.
N C
DO NOT cycle operator before limit sensors and DIP-switches have been adjusted, damage could occur to gate and operator. Please refer to the Wiring/Owner’s manual.
D Not included - Refer to a specific Radio
B
Securely mount control box near the actuator arm with appropriate hardware (not included).
Radio Receiver
I
DO NOT connect the Primary operator to this connection. Connect Secondary operator ONLY.
Control Box
manual and Loop Information Manual (available free from www.dkaccess.com) for more information.
N O
Manually move the gate to the desired open or closed wn lo D imit position. Loosen the limit nuts and S 6 5L slowly slide the limit assembly until the LIMIT LED on the circuit board lights up.
9409
Dual Channel Reverse and Shadow Plug-In Loop Detector
Single Channel Exit Plug-In Loop Detector
it
A support bar must be installed the entire length of the gate to support the pickets.
C
9410
4 Open Input 5 Open Input
Manual Release
C Not included - Refer to the Wiring/Owner’s
To #8
C
1. ON - Relay for Dual Plug-In Shadow Loop 2. OFF - Relay for Dual Plug-In Shadow Loop 3. OFF Note: Please refer to the 4. OFF Wiring/Owner’s manual for SW 2 more information.
Plug-In Loop Detectors
To #11
Com
OP EN
0°
RESET BUTTON: Resets circuit board. Mounting Holes
Com Relay 24V
18
ut
Weld front and rear brackets in positions shown. Tip: Cover the actuator arm to protect it from welding sparks before doing any welding.
KEY SWITCH BUTTON: Cycles operator when pressed.
Low Voltage
OP EN
0°
Remove Actuator Cover Manual Release
Circuit board power must be on to adjust limit sensors, LEDs will light.
Slow Down
18
1. Direction Primary operator opens. 2. OFF B 3. OFF 4. ON Auto-Close Timer 5. ON - Shadow Loop 1 23 6. OFF Adjust 1 to 23 sec. 7. OFF SW 1 8. OFF ON
Note: Front clevis pin MUST fit into countersunk hole to allow retaining ring to be installed.
A
OP EN
Allen wrench is inside of cover.
Retaining Ring
Typical Settings for Single Operator with Plug-In Loops. See reverse side.
1 2 3 4
J
Limit Sensors
Rear
Circuit Board Settings ON
Front
12 V 3 Amp/Hr Battery
Front Bracket ONLY
7/8”
Cover holes with aluminum tape on top ONLY.
1 2 3 4 5 6 7 8
2
General Information
Rear Bracket Pivot Point
46 3/4” Closed Position
120 S. Glasgow Avenue Inglewood, California 90301 U.S.A.
12 V 3 Amp/Hr Battery
Front Bracket Pivot Point
Gate Hinge Pivot Point
OP EN
Arm in Closed Position
Pedestrians must be supplied with a separate access opening. For safety and installation instructions, please refer to the 6002 Actuator Arm and Control Box Mounting manual and the 115 VAC Control Box Wiring/Owner’s manual.
F HIGH VOLTAGE! White - Neutral Black - 115 VAC Hot Green - Chassis Ground
Alarm Reset
Chassis Ground
Tip: Never run low voltage rated wire insulation in the same conduit as high voltage rated wire insulation. Keep them in separate conduits.
High Voltage
Mounting System and Adjusting Open/Close Position
Model 115 VAC 6002 is intended for installation only on swing gates used for vehicles.
Tip: It is recommended that a surge suppressor be installed on the high voltage power lines.
Note: To turn-off ALL power to the operator, the AC power switch must be turned off AND the battery plug must be disconnected from the circuit board. Wire Size
14 AWG 12 AWG
Distance
Up to 200 ft 115 VAC Input Power Wire Beyond 200 ft 6002-066-J-2-15
QUICKSTART “BASIC” GUIDELINES FOR MODEL 115 VAC 6002 - DIP-SWITCH AND WIRING REFERENCE Model 115 VAC 6002 is intended for installation only on swing gates used for vehicles.
120 S. Glasgow Avenue Inglewood, California 90301 U.S.A.
24 VAC Input
24 VAC Input
Low Voltage Common
Alarm Reset
Not Used
12 Volt Battery Input
Not Used
DC Lock Power Common
Dry Relay Contact
7 8
Dry Relay Contact
6
Low Voltage Common
Low Voltage Common
5
Standard Reverse
Full Open
2 3 4
Low Voltage Common
OFF setting. Opens counter-clockwise.
1
Full Open
Description Opening Direction of PRIMARY Operator
24 VDC - 250 ma max.
Setting
Full Open
Switch Function
Low Voltage Common
SW 1 DIP-Switches
24 VDC Maglock Power
Main Terminal
Pedestrians must be supplied with a separate access opening. For safety and installation instructions, please refer to the 6002 Actuator Arm and Control Box Mounting manual and the 115 VAC Control Box Wiring/Owner’s manual.
9 10 11 12 13 14 15 16 17 18 19 20
OFF setting. Opens clockwise.
1
Magnetic Lock
Auto-Close Timer
5
Reverse Not Used
6
Overlapping Gates
OFF Both operators start at the same time. ON Secondary operator opens 1-2 seconds before primary operator. Vice-versa when closing.
7
Single Dual Input Power
OFF Switch must be OFF for single operator. ON Switch must be ON when (dual) operators are used. OFF Switch MUST be in the OFF position.
8
ON
1 2 3 4
SW 2
Function
1 and 2
Relay Operation
3
Maglock Used No Maglock Spare
4
Com
Auto-close timer is OFF. Manual input required to close gate. Auto-close timer is ON. Adjustable from 1-23 seconds. Terminal #8 is a standard Reverse input. On setting is NOT used.
Power Relay Relay Com Power Com
4-Wire RF Receiver
Note: After a DIP-switch setting is changed, press the reset button for new settings to take effect.
SW 2 DIP-Switches Switch
3-Wire RF Receiver Do not power any control devices from the circuit board other than low voltage devices.
ON (normal) Terminal #4 is normal open command. OFF ON OFF (normal) ON
Power
4
OFF Terminal #4 is output from plug-in exit loop detector installed in EXIT loop port.
Relay
Exit Loop Port Output Open Input
Setting 1-OFF 1-OFF 1-ON 1-ON
2-OFF 2-ON 2-OFF 2-ON ON OFF OFF
Description
Relay activates when gate is fully open. Relay activates when gate is not closed. Relay activates when gate is opening and open. Shadow loop setting if used. Relay activates when gate is opening and closing. 1 second delay to disengage maglock. Leave in the OFF position if a maglock is NOT used. Leave in the OFF position.
SW 2
Switch 3 ON Note: Circuit board provides 24 VDC to power maglock. Contact rating is 1 amp maximum at 24 Volts. Safety Opening Device Com (Dry contact) N.O.
Connect optional control devices to the main terminal. Use 18 AWG wire for all low voltage wiring, maximum distance 3000 feet. Use a low voltage surge suppressor, (DoorKing P/N 1878-010) if low voltage wire runs exceed 1000 feet. All control device inputs to the terminal must be NORMALLY OPEN.
Com N.O.
Keypad (Dry contact)
Com
Deluxe 115 VAC Control Box Three 115 VAC Convenience Outlets Power safety and opening devices that require 115 VAC power.
Controls must be far enough from the gate so that the user is prevented from coming in contact with the gate while operating the controls.
ON
3
Same opening directions as illustrated above for the primary operator type. • Switch 2 will be the SAME setting as switch 1. Note: SW1, switch 7 MUST also be ON when using a secondary operator.
N.C.
1 2 3 4 5 6 7 8
2
Opening Direction of SECONDARY Operator
Reversing input on Terminal #8 functions ONLY while the gate is at the FULL OPEN position or during the CLOSING cycle. It MUST NOT be used as an input for a secondary entrapment protection device during the OPENING gate cycle. Refer to Secondary Entrapment Protection Wiring in the Wiring/Owner’s manual.
ON
SW 1
ON setting. Opens counter-clockwise.
1 2 3 4
ON
1 2 3 4 5 6 7 8
ON setting. Opens clockwise.
Com
SW 1
N.O.
Key Switch (Dry contact)
Switch 3 MUST be ON.
Com N.O.
Telephone Entry Note: Must use a separate power source.
