Preview only show first 10 pages with watermark. For full document please download

60701-002 Parts List Ip205bh-im/b

   EMBED


Share

Transcript

(20) 3600 RPM INDUSTRIAL - GENERATORS \ ILLUSTRATED PARTS LIST 15 AMP 125 VOLT RECEPTACLES ARMATURE SCHEMATIC DIAGRAM L This IPL contains wiring, illustration, parts list, ordering information and technical data to perform routine maintenance on this generator. Consult factory with model no., serial no. and test data for further assistance. ~ ~ O 45 Years of Leadership W PLANTS-Over E R --. ~ . -- ~. - WPL 20002-N80 MODEL IP205BH-lM/B REF. NO. DESCRIPTION QTY. '[:: \F DESCRIPTION 000 001 002 003 004 005 006 007 008 009 010 011 Hardware Hex Nut I/i-20 Lockwasher lh Split Lockwasher 5/,, Split Cap Screw Cap Screw 3/,-16 x 1% Lockwasher 7 , Int. Tooth Flat Washer Hex Nut%,-24 Hex Nut %,-A8 Cap Screw %,-I8 x 1% Machine Screw 8-32 x 5/,, 100 1 103 104 Type DrivelEngine B & S 130232 0301-01 Handle Handle Grip 638 440 Field Shell & Coil Ass'y. 479 441A Field Coil 480 441 B Field Coil 55576 442 Pole Shoe 1743 443 Pole Shoe Retainer 55224 444 Field Shell & Bracket 23558 445 Stud 23605 447 Brush Assembly AC 458 9416 460 Brush Rack Assembly 40746 462 Brush Holder 465 Mounting Plate & Rect. 53655 466 Capacitor 1 1 53583 57503 400 401 402 Generator Fan Assembly Thru Bolt 1 1 1 411 End Bracket 1 55311 54967 600 23197-3 608 609 43887 430 431 432 Armature Assembly Armature Bearing 1 1 1 55273 55273-1 55223 L W' 3 3 11 4 4 1 1 1 6 4 8 490 491 492 QTY. 1 1 1 2 2 1 3 4 55312 53615 53615-1 53612 53613 53614 23817 23607 1 4 1 1 55092 23500 55495 54977 End Cover Assembly End Cover Receptacle 1 1 2 55281 55304 53636 Base Assembly Base Channel Shock Spring 2 4 55094 55096 PARTS ORDERING INFORMATION REQUIRED To fill your order for service parts, please advise the complete Generator model number and serial number, part number(s), and part description. If in doubt, consult the factory prior to placing the order. Send all parts orders to WINCO, Division of Dyna Technology, Inc., 225 South Cordova Ave., Le Center, MN 56057. TECHNICAL DATA GENERATOR SPECIFICATIONS: Watts-2500; Volts-115; Amps.-21.7; PH-1; HZ-60; RPM-3600 Nominal Voltage: 115 Volts A.C. No Load: 132 Volts A.C. Full Load: 112 Volts A.C. Resistance: Field Coils-12.65 + .65 ohms Armature-Less than 1 ohm ring to ring Excitation Voltage: Approximately 55 Volts D.C. Separately Excited: 12 VDC to the Positive Field Lead (Disconnected from rectifier) 50 to 70 VAC Output BASIC TEST PROCEDURE: Refer to illustration for component location by Reference Number. Example: No output-Check field coils for opens or shorts. Reference Number 441A and 441 B. No Output: Check Check Check Check Check for loose or open connections. rectifier, located on Reference Number 465. field coils for opens or shorts Reference Number 441A and 441 B. brushes for wear, proper seating, and not stuck in holder, Reference Number 447. armature for opens or shorts, Reference Number 431. Low Voltage- No Load: Check generator speedlfrequency. (3600 RPM nominal) Check for loose or open connections. Check winding resistance, Reference Numbers 441A-441B, and 431. Low Voltage-Full Load: Check Generator speedlfrequency. (3600 RPM nominal) Check generator load. Check for loose or open connections. Check winding resistance, Reference Numbers 441A-441B, and 431. Division of DYNA TECHNOLOGY, INC. Printed in U.S.A. 225 South Cordova Le Center, MN 56057 Phone (612) 357-6821 Telex 290753