Transcript
t
20-inch Self-Contained Carpet Extractor Operator and Parts Manual
Model No.: 607058 - 120V
604507 Rev. 03 (12-2005)
604507 Home
Find... Go To..
OPERATION This manual is furnished with each new model. It provides necessary operation and machine maintenance instructions and an illustrated parts list.
MACHINE DATA
Read this manual completely and understand the machine before operating or servicing.
Please fill out at time of installation for future reference.
When ordering replacement parts, use the Parts List in this manual. Before ordering parts or supplies, be sure to have your machine model number and serial number handy. Parts and supplies may be ordered by phone or mail from any Authorized Service Center or Distributor.
Model No.Install. Date Serial No.-
This machine will provide excellent service. However, the best results will be obtained at minimum costs if:
S The machine is operated with reasonable care. S The machine is maintained regularly - per the maintenance instructions provided.
S The machine is maintained with manufacturer supplied or equivalent parts.
Tennant Company PO Box 1452 Minneapolis, MN 55440 Phone: (800) 553--8033 or (763) 513--2850 www.tennantco.com Specifications and parts are subject to change without notice. Blue Star and the Blue Star logo are registered United States trademarks of Tennant Company.
Copyright E1999, 2005 Tennant Company. All rights reserved.
TABLE OF CONTENTS SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . GROUNDING INSTRUCTIONS . . . . . . . . . . . .
3 4
SETUP AND OPERATION . . . . . . . . . . . . . . . . . . .
5
UPHOLSTERY CLEANING . . . . . . . . . . . . . . . . . . .
6
MACHINE MAINTENANCE . . . . . . . . . . . . . . . . . .
6
RECOMMENDED STOCK ITEMS . . . . . . . . . . . . .
6
TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . .
7
ELECTRICAL DIAGRAM . . . . . . . . . . . . . . . . . . . .
8
2
Home
PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CHASSIS GROUP . . . . . . . . . . . . . . . . . . . . . . . TANK GROUP . . . . . . . . . . . . . . . . . . . . . . . . . . BASE GROUP . . . . . . . . . . . . . . . . . . . . . . . . . . PUMP BREAKDOWN . . . . . . . . . . . . . . . . . . . .
10 10 12 14 16
OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 mm (5 in) HAND TOOL . . . . . . . . . . . . . . . 76 mm (3 in) CREVICE TOOL . . . . . . . . . . . . . LOW PRESSURE UPHOLSTERY TOOL . . . . SOLUTION AND VACUUM HOSES . . . . . . . . 330mm (13 in) LOW PRESSURE FLOOR TOOL . . . . . . . . . . . . . . . . . . . . . . . . . . . 406mm (16 in) LOW PRESSURE FLOOR TOOL . . . . . . . . . . . . . . . . . . . . . . . . . . .
17 17 17 18 19
Find... Go To..
20 22
20-inch Self-Contained Carpet Extractor (12--05)
OPERATION
SAFETY PRECAUTIONS This machine is intended for commercial use. It is designed exclusively to clean carpet and upholstery in an indoor environment and is not constructed for any other use. Use only recommended accessory tools and commercially available carpet cleaners intended for machine application. All operators must read, understand and practice the following safety precautions. The following warning alert symbol and the “FOR SAFETY” heading are used throughout this manual as indicated in their description: WARNING: To warn of hazards or unsafe practices which could result in severe personal injury or death. FOR SAFETY: To identify actions which must be followed for safe operation of equipment. Failure to follow these warnings may result in personal injury, electrical shock, fire or explosion. WARNING: Fire Or Explosion Hazard: --
Never Use Flammable Liquids Or Operate Machine in Or Near Flammable Liquids, Vapors Or Combustible Dusts. This machine is not equipped with explosion proof motors. The electric motors will spark upon start up and during operation which could cause a flash fire or explosion if machine is used in an area where flammable vapors/liquids or combustible dusts are present.
--
Do Not Pick Up Flammable Materials Or Reactive Metals.
WARNING: Electrical Hazard. Do Not Operate With Damaged Power Cord. Do Not Modify Plug. Unplug power Cord Before Servicing Machine. If the supply cord is damaged or broken, it must be replaced by the manufacturer or it’s service agent or a similarly qualified person in order to avoid a hazard.
The following information signals potentially dangerous conditions to the operator or equipment: FOR SAFETY: 1. Do not operate machine: -- With flammable liquids or near flammable vapors as an explosion or flash fire may occur. -- Unless trained and authorized. -- Unless operator manual is read and understood. -- Unless cord is properly grounded. -- With damaged cord or plug. -- If not in proper operating condition. -- In outdoor areas. -- In standing water. -- With the use of an extension cord. 2. Before operating machine: -- Make sure all safety devices are in place and operate properly. -- Place wet floor signs as needed. 3. When using machine: -- Do not run machine over cord. -- Do not pull machine by plug or cord. -- Do not pull cord around sharp edges or corners. -- Do not unplug by pulling on cord. -- Do not stretch cord. -- Do not handle plug with wet hands. -- Keep cord away from heated surfaces. -- Report machine damage or faulty operation immediately. -- Follow mixing and handling instructions on chemical containers -- Never allow children to play on or around. 4. Before leaving or servicing machine: -- Turn off machine. -- Unplug cord from wall outlet.
WARNING: Spinning Brush. Keep Hands Away. Turn Off Power Before Working On Machine. WARNING: Electrical Shock Hazard. Do Not Use Outdoors. Do Not Expose To Rain. Store Indoors.
20-inch Self-Contained Carpet Extractor (12--05)
Home
Find... Go To..
3
OPERATION 5. When servicing machine: -- Unplug cord from wall outlet. -- Avoid moving parts. Do not wear loose jackets, shirts, or sleeves. -- Use manufacturer supplied or approved replacement parts. -- All repairs must be performed by a qualified service person. -- Do not modify the machine from its original design. 6. When transporting machine: -- Get assistance when lifting machine. -- Unplug cord from wall outlet. -- Use tie--down straps to secure machine to truck or trailer.
GROUNDING INSTRUCTIONS Machine must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electrical current to reduce the risk of electrical shock. This machine is equipped with a cord having an equipment--grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed in accordance with all local codes and ordinances. Do not remove ground pin; if missing, replace plug before use. Grounded 3 Hole Outlet
Ground Pin
4
Home
Find... Go To..
20-inch Self-Contained Carpet Extractor (12--05)
OPERATION
SETUP AND OPERATION
If the supply cord is damaged or broken, it must be replaced by the manufacturer or it’s service agent or a similarly qualified person in order to avoid a hazard.
FOR SAFETY: Do not use machine unless operator manual is read and understood.
FOR SAFETY: Do not operate machine with the use of an extension cord.
1. Pour a recommended liquid cleaning agent into the solution tank, according to bottle’s mixing instructions.
4. Turn the height adjustment knob (located at front of machine) to raise or lower the brush to your carpet type.
WARNING: Fire Or Explosion Hazard: Never Use Flammable Liquids. 2. Using a clean bucket, fill solution tank with 30 liters (8 gal) hot water, 60_ C (140_ F) max. If powdered cleaning chemicals are used, mix the powders in the filling bucket. DO NOT MIX POWDERED CHEMICALS IN THE SOLUTION TANK! This can plug the pumping system with undissolved powder. NOTE: The water must not be hotter than 60_C (140_F) or tank damage may occur. NOTE: Use different buckets to fill and drain machine to prevent solution system clogs. FOR SAFETY: When using machine, follow mixing and handling instructions on chemical containers. ATTENTION: If using powdered cleaning chemicals, mix prior to adding. NOTE: If desired, hot water alone achieves excellent cleaning results. 3. Plug the power cord into a grounded 120 volt outlet (Figure 1).
5. Turn on VACUUM switch. 6. Position the extractor at the first area to be cleaned. Press and hold the INTERMITTENT button. This starts the solution spray and brush. Pull the extractor toward you about 1219 mm (4 ft), then release the INTERMITTENT button to stop spray, but continue to pull the machine toward you for another 305 mm (1 ft). Then, push down on the handle and roll the machine forward to the next strip, overlapping about 51 mm (2 in). WARNING: Fire Or Explosion Hazard. Do Not Pick Up Flammable Materials Or Reactive Metals. NOTE: If the brush stops during operation, UNPLUG THE EXTRACTOR, dislodge any obstructions near the brush, then reset the circuit breaker button located on the back panel of the extractor. 7. While cleaning, watch the recovery tank for foam buildup. If foam does appear, pull the clear vacuum hose off the hose barb. Pour about 31 mL (2 Tbs) of defoamer into the hose barb with the vacuum motor running to draw defoamer into the tank. ATTENTION: Foam or water will damage the vacuum motors. Always prevent foam or water from entering the screen by using defoamer. Damage due to foam or water is NOT COVERED BY WARRANTY.
Grounded 3 Hole Outlet
8. When the recovery tank is full, turn off vacuum switch, remove clear lid, lift out recovery tank and drain. Do not use the recovery tank to fill the clean water tank. Instead, use a clean bucket or hose. 9. When you have finished cleaning, use the black hose included to vacuum out any water left in the solution tank. Empty the recovery tank and rinse it to prevent odor buildup.
Ground Pin
Figure 1 FOR SAFETY: Do not use machine unless cord is properly grounded. WARNING: Electrical Hazard. Do Not Operate With Damaged Power Cord. Do Not Modify Plug.
20-inch Self-Contained Carpet Extractor (12--05)
Home
Find... Go To..
5
OPERATION
UPHOLSTERY CLEANING
MACHINE MAINTENANCE
The machine cleans most fabrics like Herculon and synthetic velvets with excellent results. Extraction is not recommended for most cottons, silks, wools or natural fiber velvets. Check the cleaning instructions sewn on the furniture by the manufacturer for further instructions. Extra caution should be taken with furniture that has been re-upholstered. Any material under the new upholstery may bleed and discolor the new fabric.
To keep your extractor in top condition, perform these preventive steps.
NOTE: When cleaning upholstery, always check cleaning instructions sewn in furniture by manufacturer. 1. Vacuum the upholstery before cleaning. 2. TEST THE FABRIC FOR COLORFASTNESS. Pour a small amount of cleaning solution on a white cloth. Hold the damp cloth against an area of upholstery which is hidden from view. Hold it there for 60 seconds. If no color transfers to the cloth, it should be safe to clean. However, always clean at your own discretion. 3. Remove the clear vacuum hose from the recovery tank lid. 4. Connect the extension vacuum hose to the recovery tank lid and to the hand tool. 5. Connect the accessory solution hose to the upholstery connection and to the hand tool. 6. Turn on the VACUUM switch. 7. Clean with the hand tool using as little cleaning solution as possible. Overlap your strokes to avoid streaking. Go over clean areas using only the vacuum to get fabric as dry as possible. WARNING: Fire Or Explosion Hazard. Do Not Pick Up Flammable Materials Or Reactive Metals. 8. When you are finished, turn off the VACUUM switch. Use the extension vacuum hose to vacuum out any water left in the clean water tank. 9. Drain the recovery tank, and disconnect the vacuum and solution hoses. ATTENTION: The solution hose contains pressurized cleaning solution which can spray when the hose is disconnected. Relieve pressure before disconnecting the hose by squeezing the Hand Tool trigger for five seconds AFTER unplugging the machine.
WARNING: Electrical Hazard. Unplug power Cord Before Servicing Machine. Contact an Authorized Service Center for machine repairs. FOR SAFETY: When servicing machine, all repairs must be performed by a qualified service person. 1. Remove carpet strands and clogging debris from the brush after every use. 2. Thoroughly rinse the recovery tank and the clear cover after every use. 3. Clean the solution tank screen and vacuum screen after every use. 4. Every forty hours of operation, run a mild acid (anti-browning chemical) through the pump system to dissolve normal alkaline chemical buildup. Pour the anti-browning chemical in the solution tank with about three gallons of warm water. Hold a bucket under the spray jets to catch spray and push the INTERMITTENT PUMP button just until the solution begins to spray through the tips. Allow the solution to remain in the system overnight in above freezing temperatures. In the morning, drain the solution then run 11.3L (3 gal) of clean water through the system to flush out impurities. ATTENTION: If storing machine in freezing temperatures, be sure that machine, pump and spraying system are completely drained and dry. Damage due to freezing temperatures is not covered by warranty. WARNING: Electrical Shock Hazard. Do Not Use Outdoors. Do Not Expose To Rain. Store Indoors.
RECOMMENDED STOCK ITEMS Refer to Parts List section for recommended stock items. Stock Items are clearly identified with a bullet preceding the parts description. See example below:
10. Rinse the recovery tank and the clear dome thoroughly to prevent odor buildup inside the tank.
6
Home
Find... Go To..
20-inch Self-Contained Carpet Extractor (12--05)
OPERATION TROUBLESHOOTING GUIDE PROBLEM
CAUSE
SOLUTION
Vacuum motor will not operate.
Fuse blown or circuit breaker tripped in building. Faulty VACUUM switch. Loose or broken wiring. Vacuum hose is loose from floor tool.
Replace fuse or reset breaker.
Poor pick--up.
Hose cuffs are loose on hoses.
Little or no spray p y from spray p y tips. p
Brush does not operate. p
Holes in hoses. Hoses are not firmly attached onto hose barbs. Gaskets worn. Hose clamp(s) loose. Vacuum motor loose. Faulty vacuum motor. Plugged screen in solution tank. Plugged spray tips in power brush base. Faulty solution pump. Faulty solenoid. One of the internal hoses is pinched. Faulty Intermittent pump switch. Carpet strands or other debris have clogged the brush and tripped the circuit breaker (located on the back panel). Brush drive belt is loose or broken.
Brush pulley, or motor pulley is loose and spinning on its shaft. Faulty brush motor. Loose wiring.
20-inch Self-Contained Carpet Extractor (06--00)
Home
Find... Go To..
Contact Service Center. Contact Service Center. Slide hose cuff firmly onto the floor tool. Turn the cuffs while holding hose to tighten cuffs onto the hose. Replace hose or hoses. Slide the hose cuffs firmly onto the hose barbs. Replace the worn gasket. Tighten clamp(s). Tighten nut(s). Contact Service Center. Clean screen or replace. Remove tips and clean in mild acid solution or replace. Contact Service Center. Contact Service Center. Move hose to remove the pinch. Replace hose if damaged. Contact Service Center. UNPLUG THE MACHINE. Remove all clogging material from the brush, then push the circuit breaker button to reset it. If belt is loose, loosen both locknuts on the drive motor. Pivot the motor away from the brush until the belt is taut and tighten the nuts again to lock the motor in position. Examine the loose pulley and the shaft carefully for damage. If there is no damage to either, tighten the set screw. Contact Service Center. Contact Service Center.
7
ELECTRICAL DIAGRAMS 120V WIRING DIAGRAM
WHT BLK
VACUUM CIRCUIT BREAKER
VACUUM SWITCH
INTERMITTENT PUMP SWITCH
BLK
WHT
BLK
PUMP CIRCUIT BREAKER
12 AMP
1.5 AMP
BLK
BLK
BLK
GRN
WHT PUMP
RED 1.5 AMP
WHT
BRUSH MOTOR CIRCUIT BREAKER
WHT
BLK
BRIDGE RECTIFIER
VACUUM MOTOR
WHT
AC GRN
SOLUTION SOLENOID
AC
WHT
WHT
WHT
RED WHT
8
BRUSH MOTOR
Home
BLK
Find... Go To..
20-inch Self-Contained Carpet Extractor (12--05)
ELECTRICAL DIAGRAMS 120V LADDER DIAGRAM
WHT
BLK 120 VAC VACUUM SWITCH
--WHT--
12A
VACUUM
--WHT--
--BLK--
1.5A
--WHT--
PUMP --BLK--
--BLK--
INTERMITTENT PUMP SWITCH --BLK--
VACUUM
1.5A --YEL--
--GRN--
--WHT--
PUMP
BRUSH --BLK--
BRIDGE RECTIFIER
BRUSH MOTOR
--RED--
--BLK--
--WHT--
--GRN--
20-inch Self-Contained Carpet Extractor (12--05)
Home
Find... Go To..
SOLUTION SOLENOID
--WHT--
9
PARTS LIST CHASSIS GROUP 1
2 24
5
9 6 7
3
38
47
4
10
8 34
12 11
35 21
21
22
17 13 16
41
46
42
37 14
25 16
40
16
44 43
45 15
29
25
19
20 39
21 22
20
31 25
30
36 23 45
33
27
32 18
29
26
30
28
23 25 10
Home
Find... Go To..
18
20-inch Self-Contained Carpet Extractor (12--05)
PARTS LIST CHASSIS GROUP REF
PART # 1
578337000AM
2 3
DESCRIPTION
QTY.
DCIRCUITBREAKER, 1.5A
2
130194
DSTRAINRELIEF
1
140328
DCLAMP, CABLE, NYL, 0.38D BLK
1
4
28683
CORD ASSY. 14/3 X 50’ YELLOW
1
5
130670AM
D CIRCUITBREAKER, 12 AMP
1
6
604448
CORD, 18/3 X 40” BK
1
7
605395
STRAINRELIEF
8
604463
9
1026383
REF
PART #
DESCRIPTION
QTY.
25
54333
CLAMP, HOSE WORMDRIVE 0.31--0.88D .31W
4
26
605394
FITTING, BRS E45 PM04/BM06 T
1
27
150403
FITTING, BRS E45 PM04/PF04 T
1
28
180628
DFILTER, SCREEN 100 MESH
29
606162
HOSE, 1/2 X 26” RED (160220)
1
30
19066
WASHER, FLAT #10
2
ASM, VAC MOTOR ENCLOSURE
1
31
150412
FITTING, 3/8M X 3/8H ELBOW 90°
1
LABEL, WARN, 7X2.25AC SCRB/ EXTR EN/FR/ES
1
32
150425
FITTING, 3/8M X 1/2H ELBOW 90°
1
33
180103
DPUMP, SOLTN 100 PSI 120V
1
34
604466
HOOK, CORD
2
35
140895
SCREW, #10 24 X 3/4”
4
36
130194
STRAINRELIEF, BUSHING
1
37
150517
FITTING, 1/4M X 1/2H BARB BRASS
1
38
150933
FITTING, 1/4F QD PLUG BRASS
1
39
606161
HOSE, 1/4 X 36” GRAY (160204)
1 2.166 ft
10
140519
NUT, KEP 10 24
1
11
07514
WASHER, LOCK, INT #10
1
12
604475
SPACER, MOTOR SUPPORT
3
13
626092
DGASKET, VAC FAN 5.7D NEO
1
14
130416
DMOTOR, VACUUM 5.7D 2S 120V
1
190160
DBRUSH, CARBON (2/PK)
1
15
2998.28
SCREW, HEX, .25--20 X 3.50
3
16
140308
CLAMP, HOSE 3/4 TO 1 3/4 DIA
3
40
160462
HOSE, VAC 1.50 X 33” WHITE
1
17
1022164
HOSE, EXHAUST 2.0”ID, 26” LG
1
41
150615
FITTING, 1/4M NIPPLE CLOSE BRS
1
18
606163
HOSE 3/8 X 22” GRAY (160207)
42
150709
TEE, STRT 1/4F X 1/4F X 1/4M BRASS
1
19
604464
PUMP ENCLOSURE
1
43
210033
DVALVE, SOLENOID 120V 60 HZ
1
20
140519
NUT, KEP 10 24
4
44
150515
FITTING 1/4M X 1/4H BARB BRASS
1
21
07514
WASHER, LOCK, INT #10
16
45
140325
CLAMP, EAR 1/2”
2
22
140892
SCREW, MACHINE 10 24 X 1/2
12
46
140029
WASHER, 9/16 INT SS
1
23
140895
SCREW, MACHINE 10 24 X 3/4
3
47
130034
WASHER, .5 FLAT
2
24
14865
STRAINRELIEF, BUSHING
1
1.833 ft
3.000 ft
D RECOMMENDED STOCK ITEMS
20-inch Self-Contained Carpet Extractor (12--05)
Home
Find... Go To..
11
PARTS LIST TANK GROUP 3
4
6
2
1
23 12
11
5
13 15
16
17 18
7
14
14
22
8 9
24
20
21
25
30
38 32
46
26
40 36
29 41
35
28
42 9
39
34
19
45 31
12
32
33
37
43
Home
27
44
10
Find... Go To..
20-inch Self-Contained Carpet Extractor (12--05)
PARTS LIST TANK GROUP REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
1
140892
SCREW, MACHINE 10--24 X 1/2
QTY. 4
25
607243
RECOVERY TANK NAVY BLUE
QTY. 1
2
07514
WASHER, LOCK, INT #10
4
26
28279
HANDLE , WITH BK. PVC DIP
1
3
130717
DSWITCH, ROCKER 250VAC 15A ON/OFF
1
27
611074
SPACER
2
28
140003
WASHER, FENDER, .25ID X 1.000
2
29
24672
SCREW, HEX, .25--20 X 0.75
2
30
160462
HOSE, VAC 1.50 X 33” WHITE
1
31
28230
RING, RETAINING
2
32
3148.816
WASHER, FLAT STEEL
4
33
103009
WHEEL, 12.0D 1.75W WHT/GRY
2
34
59156
NUT, HEX, LOCK, .38--16 NL
1
35
4252
WASHER, COMPRESSION ZINC
2
36
28114
AXLE, WHEEL ZINC
1
4
130712
DSWITCH, PUSH 250VAC 15A
1
5
608559
LABEL, PUMP SWITCH
1
6
604468
SWITCHBOX
1
7
607245
TANK, SOLUTION, NAVY BLUE
1
8
140256
SCREW, 3/8 16 X 2 1/2
1
9
140028
WASHER, FLAT 3/8
2
10
230637.BK
TOOL, PICKUP 20W FLOOR BLK
1
11
28358
HOSE, 17” CLEAR WHITE W/1--1/2” CUFFS
1
12
28231
HOSE, 17”
1
37
28337
SCREW, 5/16 18 X 1”
4
2
38
32490
WASHER, FLAT, 0.25 STD
4
140546
NUT, LOCK 5/16 18
4
13
611069
FITTING, HOSE BARB
14
210234
GASKET, DRAIN VALVE
4
39
15
611861
LABEL, “ACCESSORY TOOL”
1
40
230635
1
16
120906
LABEL, “IMPORTANT DRAIN”
1
BRACKET, MOUNTING BRUSH BASE
17
602819
DCOVER, RECOVERY TANK
1
41
140914
SPACER
1
18
120399
LABEL, “DO NOT ALLOW FOAM”
1
42
140898
SCREW, 3/8 16 X 3/4
2
19
200825
DSHOE, STAINLESS STEEL 20”
2
43
140016
WASHER, LOCK 1/4”
2
20
611063
FITTING, PVC E90 1--1/2F X 1--1/2S, 40
1
44
24672
SCREW, HEX, .25--20 X 0.75
2
45
140313
CLAMP, FLOOR TOOL
1
46
607081
LABEL, LOGO BLUESTAR 140 X 64
1
21
611084
FITTING, PVC 1--1/2F X 1--1/2S REWORKED
1
22
25203
DSCREEN
1
23
160404
HOSE, VACUUM 1 1/2 X 5’ W/1 CUFF
1
24
102538
DGASKET, DOME
1
D RECOMMENDED STOCK ITEMS
20-inch Self-Contained Carpet Extractor (12--05)
Home
Find... Go To..
13
PARTS LIST BASE GROUP 1
43
12 11
7 2
9
8
13 15
14 10
3 46 5
6
16 17 18
27
19
9
42
44
37
28
29
23
41
21 20
40
39
24
38
25 30
32 45 28
34 35
26 30 29
36
31
22
27
14
33
4
Home
Find... Go To..
20-inch Self-Contained Carpet Extractor (12--05)
PARTS LIST BASE GROUP REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
1
240194
DKNOB, HEIGHT ADJ.
QTY. 1
23
140539
NUT, 6--32
1
2
230258
DSTUD, THREADED
1
24
140898
SCREW, 3/8 16 X 3/4
2
3
230638.BK
BRACKET, HEIGHT ADJ.
1
25
140914
SPACER
2
4
140887
SCREW, 10 24 X 3/8
12
26
1019015
DMOTOR, ELE, 115VDC, .125HP, 3D
1
5
140564
BOLT, 3/8 X 3/4
2
27
230261
DBLOCK, BEARING
2
6
607247
BASE, 20”, NAVY BLUE
1
28
140125
DBEARING, BRUSH
2
7
140407
SPRING, .845
1
29
100049
DSEAL, BRUSH BEARING
2
8
59156
NUT, HEX LOCK, .38--16, NL
1
30
230362
SHAFT, BRUSH 20”
1
9
140036
WASHER, FLAT 3/8
2
31
240050
BRUSH, CYLINDER
1
10
230264.BK
CLAMP, SPRAYBAR MANIFOLD BLK
1
32
24672
SCREW, HEX .25--20 X 0.75
4
33
230506
DPULLEY, MOTOR W/SCREW
1
34
140518
NUT, KEP 10 32
2
35
230366
PLATE, MOTOR MOUNT
1
36
100115
GASKET, 20” POWER BRUSH BASE
1
11
150422
ELBOW, 45°
1
12
150616
ADAPTER, BRASS
1
13
120617
LABEL, “HEIGHT ADJUSTMENT”
1
701171
DASM, SPRAYBAR 20” TWISTOUTS
1
∇
QTY.
Y
14
230379
DMANIFOLD, SPRAYBAR 20”
1
37
100005
DGASKET, BEARING BLOCK
1
Y
15
150208
DPLUG, BRASS HEX HEAD 1/8
3
38
230363
SPACER
1
Y∇ 16
201011
DASM., SPRAYTIP
5
39
230505
DPULLEY, BRUSH W/SCREWS
1
Y17
201015
DSEAL, SPRAY NOZZLE
5
40
140548
NUT, 5/16 FINJAM
1
Y18
201013
DTIP, FITTING
5
∇ 41
130665
DCORD, 18/3 X 24” BLACK, ASM.
1
19
230635
BRACKET, BRUSH ASSY.
1
Y
42
130190
DGRIP, CORD STRAINRELIEF 3/8N
1
20
140829
SCREW, 6/32 X 5/8
1
43
150526
FITTING, BRS, STR, JF04/BM04
1
21
130304
DRECTIFIER
1
44
140233
SCREW, 3/8 16 X 1 3/4
1
22
611918
PLATE, BASE 20” YLW CHROMATE
1
45
230507
DBELT, BRUSH DRIVE
1
46
140919
SPACER, PLSTC, 0.38 X .12 THK, NY
1
∇ ASSEMBLY Y INCLUDED IN ASSEMBLY D RECOMMENDED STOCK ITEMS
20-inch Self-Contained Carpet Extractor (12--05)
Home
Find... Go To..
15
PARTS LIST PUMP BREAKDOWN
2
3
4
5 6 1
REF
PART #
DESCRIPTION
QTY.
REF
PART #
DESCRIPTION
QTY.
∇
1
180103
DPUMP, 100 PSI 120V (COMPLETE)
1
Y
4
190171
DKIT, PUMP VALVE (VITON)
1
Y
2
190129
DKIT, PUMP PRESSURE SWITCH
1
Y
5
190131
DKIT, PUMP SERVICE
1
190172
DKIT, PUMP PRS SWITCH (VITON)
1
Y
6
190130
DKIT, PUMP LOWER HOUSING
1
190134
DKIT, PUMP DIAPHRAGM ONLY
1
190128
DKIT, PUMP UPPER HOUSING
1
190124
DKIT, PUMP CHECK VALVE ONLY
1
Y
3
∇ ASSEMBLY Y INCLUDED IN ASSEMBLY D RECOMMENDED STOCK ITEMS
16
Home
Find... Go To..
20-inch Self-Contained Carpet Extractor (12--05)
OPTIONS 127 mm (5 in) HAND TOOL 1
6 5 3
2
3 4 8 9
7
10 11 12
REF
PART #
DESCRIPTION
PART #
DESCRIPTION
∇
200505
DASM., HAND TOOL 5” SERIES 60
QTY. 1
REF Y
7
140609
PIN, ROLL 0.187D X 0.56L
QTY. 1
TOOL, HAND BLACK
1
Y
8
150403
FITTING, BRS E45 PF04/PF04
1
Y
1
200431.BK
Y
2
150913
FITTING, BRS QDC PF04 SER60
1
Y
9
200992
FITTING, BRS STR PF02 SWIVEL
1
Y
3
150606
FITTING, BRS STR PF04 HEX NIP
2
Y
10
200996
FILTER, SCREEN 100MESH
1
Y
4
200905
LEVER, K--VALVE W/PIN
1
Y
11
200965
DFITTING, BRS TIP, 8002 T--JET
1
Y
5
210210
DVALVE, FLOW CONTROL 04PF
1
Y
12
200994
CAP, NOZZLE SPRAY (8002)
1
Y
6
190600
KIT, K--VALVE REPAIR
1
∇ ASSEMBLY Y
INCLUDED IN ASSEMBLY
D RECOMMENDED STOCK ITEMS
76 mm (3 in) CREVICE TOOL
1 6
7
5
2
3 4
REF
PART #
DESCRIPTION
PART #
DESCRIPTION
∇
200517
DTOOL, CREVICE LP/HP SER 60
QTY. 1
REF Y
4
210020
POSITIONER, VALVE HANDLE
QTY. 1
Y
1
200436.BK
TOOL, CREVICE BLACK
1
Y
5
160106
HOSE, SOLUTION CREVICE TOOL
1
Y
2
200975
DFITTING, BRS TIP #5002 1/8V--JET
1
Y
6
150100
FITTING, BRS STR PF04/PF02
1
Y
3
210014
DVALVE, TOGGLE 02PF W/NUT
1
Y
7
150913
FITTING, BRS QDC PF04 SER 60
1
∇ ASSEMBLY Y
INCLUDED IN ASSEMBLY
D RECOMMENDED STOCK ITEMS
20-inch Self-Contained Carpet Extractor (12--05)
Home
Find... Go To..
17
OPTIONS LOW PRESSURE UPHOLSTERY TOOL 1 2
5 4
3
8
9
13
14
7 12
6
11 10
REF
PART #
DESCRIPTION
∇
200540
DTOOL, UPHOLSTERY LP SER 60
QTY. 1
REF Y
PART #
DESCRIPTION
8
200844
DHOSE, VAC UPHOLSTERY TOOL W/O CUFFS
QTY. 1
Y
1
200845
COVER, UPHOLSTERY TOOL
1
Y
2
200843
GASKET, COVER
1
Y
9
200837
DHOSE, UPHOLSTERY TOOL
1
1
Y
10
200848
FITTING, BRASS (3 PCS)
1
11
200842
FILTER, INLINE COMPLETE
1
Y
3
190631
DKIT, SERVICE LP UPHOLSTERY
Y
4
210226
DVALVE, WATER/SOL 120VAC LP
1
Y
Y
5
200991
DFITTING, SS TIP 1/8K--JET
1
Y
12
200841
SCREEN ONLY, INLINE FILTER
1
4
Y
13
150606
FITTING, BRS STR PF04 HEX NIP
1
1
Y
14
150913
DFITTING , BRS QDC PF04 SER 60
1
Y Y
6 7
200838 200840
SCREW, #06--32 X 0.75 TRIGGER, UPHOLSTERY TOOL
∇ ASSEMBLY Y INCLUDED IN ASSEMBLY D RECOMMENDED STOCK ITEMS
18
Home
Find... Go To..
20-inch Self-Contained Carpet Extractor (12--05)
OPTIONS SOLUTION AND VACUUM HOSES 5
7
1 3
4 6 4 2
REF ∇
PART #
DESCRIPTION
160185
HOSE, SOLUTION 4.6M (15’)
1
160186
HOSE, SOLUTION 7.6M (25’)
160187
HOSE, SOLUTION 15.2M (50’)
1
QTY.
REF
PART #
DESCRIPTION
160400
HOSE, VACUUM 4.6M (15’)
1
1
160401
HOSE, VACUUM 7.6M (25’)
1
1
160402
HOSE, VACUUM 15.2M (50’)
1
∇
5
QTY.
Y
2
150913
DFITTING, BRS QDC PF04 SER 60
1
Y
6
160430
DCUFF, HOSE 1.5 X 1.5 BLACK
2
Y
3
150933
FITTING, BRS QDC PM04 SER 60
1
Y
7
160451
4
150615
FITTING, BRS STR PM04 CLOSE
2
DCONNECTOR, VAC HOSE 38MM (1.5IN)
1
Y
220040
DBAG, HOSE NYLON MESH W/DRAWSTRING
1
N/S
∇ ASSEMBLY Y
INCLUDED IN ASSEMBLY
D RECOMMENDED STOCK ITEMS
20-inch Self-Contained Carpet Extractor (12--05)
Home
Find... Go To..
19
OPTIONS 330mm (13 in) LOW PRESSURE FLOOR TOOL
6
1
8 10
7
4
11
9 12 5
14
13 26 15 16
2
16
17 18 19 20 21 3 22 23 24 25
20
Home
Find... Go To..
20-inch Self-Contained Carpet Extractor (12--05)
OPTIONS 330mm (13 in) LOW PRESSURE FLOOR TOOL REF
PART #
DESCRIPTION
600048
DTOOL, 330MM (13 IN) FLOOR LP SER 60
1
TOOL, FLOOR BLACK
1
∇
QTY.
Y
1
200403.BK
Y
2
120846
DECAL, LOW PRESSURE TOOL
1
Y
3
200939
DSHOE, 330MM (13 IN) FLR TOOL
2
Y∇
4
200927AM
GRIP, HAND ADJ. COMPLETE
1
Y
5
01697
SCREW, HEX .25--20 X 0.62
2
Y
6
200912
GRIP, HANDLE FOAM
1
Y
7
140834
SCREW, FLT .25--20 X 0.62 PHL
2
Y
8
200809
SLEEVE, HANDLE FLOOR TOOL
1
Y
9
200902
HANDLE, IMPERIAL VALVE
1
Y
10
140605
PIN, HANDLE IMPERIAL
1
Y
11
140520
NUT, 1/4 PUSH BLK
2
Y
12
150403
FITTING, BRS E45 PM04/PF04
1
Y
13
150913
DFITTING, BRS QDC PF04 SER 60
1
REF
PART #
DESCRIPTION
Y∇ 14
210150
DVALVE, FLOW CONTROL PF04
QTY. 1
Y15
190603
DKIT, REPAIR IMPERIAL
1
Y
16
160170
WAND, HOSE ASSEMBLY 46”
1
Y
17
150606
FITTING, BRS STR PM04 HEX NIP
1
Y
18
140058
WASHER, .54B X .88D X .06 WAND
1
700062
ASM., SPRAYBAR WO/TIPS
1
Y19
150700
FITTING, BRS TEE PF04 CROSS
1
Y20
150600
FITTING, 1/4MX2” NIPPLE BRS
2
Y21
150401
FITTING, BRS E90 PF04/PF04
2
Y∇
Y22
200993
SPRAY BODY, 1/4” MALE BRASS
3
Y
23
200996
DFILTER, SCREEN 100 MESH
3
Y
24
200964
DFITTING, TIP 11003 T--JET BRS
3
Y
25
200994
DCAP, NOZZLE SPRAY (8002)
3
Y
26
150615
FITTING, BRS STR PM04 CLOSE
1
∇ ASSEMBLY Y
INCLUDED IN ASSEMBLY
D RECOMMENDED STOCK ITEMS
20-inch Self-Contained Carpet Extractor (12--05)
Home
Find... Go To..
21
OPTIONS 406mm (16 in) LOW PRESSURE FLOOR TOOL
6
1 8 10
7 4
11
9 12 5
15
14
13
16 17 2
17
18 19 20 21 22 23
3
24 25 26 27
22
Home
Find... Go To..
20-inch Self-Contained Carpet Extractor (12--05)
OPTIONS 406mm (16 in) LOW PRESSURE FLOOR TOOL REF
PART #
DESCRIPTION
200503
DTOOL, 406MM (16 IN) FLOOR LP SER 60
1
TOOL, FLOOR 406MM (16 IN)
1
∇
QTY.
Y
1
200411.BK
Y
2
120846
DECAL, LOW PRESSURE TOOL
1
Y
3
200956
DSHOE, 406MM (16 IN) FLR TOOL
2
Y∇
4
200927AM
GRIP, HAND ADJ. COMPLETE
1
Y
5
01697
SCREW, HEX .25--20 X 0.62
2
Y
6
200912
GRIP, HANDLE FOAM
1
Y
7
140834
SCREW, FLT .25--20 X 0.62 PHL
2
Y
8
200809
SLEEVE, HANDLE FLOOR TOOL
1
Y
9
200902
HANDLE, IMPERIAL VALVE
1
Y
10
140605
PIN, HANDLE IMPERIAL
1
Y
11
140520
NUT, 1/4 PUSH BLK
2
Y
12
150403
FITTING, BRS E45 PM04/PF04
1
Y
13
150913
DFITTING, BRS QDC PF04 SER 60
1
Y
14
150615
FITTING, BRS STR PM04 CLOSE
1
REF
PART #
DESCRIPTION
Y∇ 15
210150
DVALVE, FLOW CONTROL PF04
QTY. 1
Y16
190603
DKIT, REPAIR IMPERIAL
1
Y
17
160170
WAND, HOSE ASSEMBLY 46”
1
Y
18
150606
FITTING, BRS STR PM04 HEX NIP
1
Y
19
140058
WASHER, .54B X .88D X .06 WAND
1
700656
ASM., SPRAYBAR 16” WO/TIPS
1
Y20
150706
FITTING, BRS TEE PF04
1
Y21
150709
FITTING, BRS TEE PF04/PF04/PF04
2
Y22
150600
FITTING, 1/4MX2” NIPPLE BRS
2
Y23
150401
FITTING, BRS E90 PF04/PF04
2
Y24
200993
SPRAY BODY, 1/4” MALE BRASS
4
Y
25
200996
DFILTER, SCREEN 100 MESH
4
Y
26
200964
DFITTING, TIP 11003 T--JET BRS
4
Y
27
200994
CAP, NOZZLE SPRAY (8002)
4
Y∇
∇ ASSEMBLY Y
INCLUDED IN ASSEMBLY
D RECOMMENDED STOCK ITEMS
20-inch Self-Contained Carpet Extractor (12--05)
Home
Find... Go To..
23
