Transcript
Type 316 Laboratory Sinks S9106/316P-1
Single compartment self rimming drop-in sink less faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 11 1/4" (286 mm) Overall left to right: 13 5/8" (346 mm) Bowl front to back: 9 1/4" (235 mm) Bowl left to right: 11 5/8" (295 mm) Bowl depth: 6" (152 mm) S9106/316P-1 Wheelchair accessible - Meets ADA (Americans with disabilities act guidelines) and ANSI A117.1 (Accessible and usable buildings and facilities). Check local codes to ensure compliance. Center waste location, 3 1/2” (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2” (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Technical data
Type of basin Single Compartment Gross weight 2.3 kg Type of waste kit 3 1/2" crumb cup strainer Faucet ledge no Undercoated yes Waste hole position centre Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
296
Type 316 Laboratory Sinks S9106/316P-3
Single compartment self rimming drop-in sink less faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 11 1/4" (286 mm) Overall left to right: 13 5/8" (346 mm) Bowl front to back: 9 1/4" (235 mm) Bowl left to right: 11 5/8" (295 mm) Bowl depth: 6" (152 mm) S9106/316P-3 Wheelchair accessible - Meets ADA (Americans with disabilities act guidelines) and ANSI A117.1 (Accessible and usable buildings and facilities). Check local codes to ensure compliance. Center waste location, 1 1/2" (38mm) type 316 (EN1.4401 17/12/2) stainless steel duplex waste assembly with rubber stopper and 1 1/2” (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Technical data
Type of basin Single Compartment Gross weight 2.3 kg Type of waste kit 1 1/2" duplex waste with rubber stopper Faucet ledge no Undercoated yes Waste hole position centre Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
297
Type 316 Laboratory Sinks S9407/316P-1
Single compartment self rimming drop-in sink less faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 11 5/8" (295 mm) Overall left to right: 16 5/8" (422 mm) Bowl front to back: 9 1/2" (241 mm) Bowl left to right: 14 1/2" (368 mm) Bowl depth: 7" (178 mm) S9407/316P-1 center waste location, 3 1/2" (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Technical data
Type of basin Single Compartment Gross weight 2.7 kg Type of waste kit 3 1/2" crumb cup strainer Faucet ledge no Undercoated yes Waste hole position centre Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
298
Type 316 Laboratory Sinks S9407/316P-3
Single compartment self rimming drop-in sink less faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 11 5/8" (295 mm) Overall left to right: 16 5/8" (422 mm) Overall height: 7" (178 mm) Bowl front to back: 9 1/2" (241 mm) Bowl left to right: 14 1/2" (368 mm) Bowl depth: 7" (178 mm) S9407/316P-3 center waste location, 1 1/2" (38mm) type 316 (EN1.4401 17/12/2) stainless steel duplex waste assembly with rubber stopper and 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece Technical data
Type of basin Single Compartment Gross weight 0.1 kg Net weight 2.1 kg Type of mounting counter top mounting Waste size DN 40 Waste kit included yes Faucet ledge no Bowl shape rounded rectangle Waste hole position centre Rear upstand no Overflow no
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
299
Type 316 Laboratory Sinks S6407/316P-1
Single compartment self rimming drop-in sink less faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 18 1/8" (460 mm) Overall left to right: 16 1/8" (410 mm) Bowl front to back: 16" (406 mm) Bowl left to right: 14" (356 mm) Bowl depth: 7" (178 mm) S6407/316P-1 center back waste location, 3 1/2" (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Technical data
Type of basin Single Compartment Gross weight 4.1 kg Type of waste kit 3 1/2" crumb cup strainer Faucet ledge no Undercoated yes Waste hole position centre Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
300
Type 316 Laboratory Sinks S6407/316P-3
Single compartment self rimming drop-in sink less faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Bowl front to back: 16" (406 mm) Bowl left to right: 14" (355 mm) Bowl depth: 7" (178 mm) S6407/316P-3 center back waste location, 1 1/2" (38mm) type 316 (EN1.4401 17/12/2) stainless steel duplex waste assembly with rubber stopper and 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece Technical data
Type of basin Single Compartment Gross weight 4.1 kg Type of mounting drop in Waste size DN 40 Waste kit included yes Type of waste kit duplex waste with rubber stopper Faucet ledge no Bowl shape rounded rectangle Bowl position center Number of bowls 1 Undercoated yes Waste hole position centre back Waste hole projection 8 3/4" (222 mm) Siphon included no Overflow no
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
301
Type 316 Laboratory Sinks S6410/316PCB-1
Single compartment self rimming drop-in sink less faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Center back waste location. Includes 3 1/2" (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 18 1/8" (460 mm) Overall left to right: 16 1/8" (410 mm) Bowl front to back: 16" (406 mm) Bowl left to right: 14" (356 mm) Bowl depth: 10" (254 mm) S6410/316PCB-1 center back waste location, 3 1/2" (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Technical data
Type of basin Single Compartment Gross weight 5 kg Type of waste kit 3 1/2" crumb cup strainer Faucet ledge no Undercoated yes Waste hole position centre back Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
302
Type 316 Laboratory Sinks S6808/316P-1
Single compartment self rimming drop-in sink less faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 18 1/8" (460 mm) Overall left to right: 20 1/8" (511 mm) Bowl front to back: 16" (406 mm) Bowl left to right: 18" (457 mm) Bowl depth: 8" (203 mm) S6808/316P-1 center back waste location, 3 1/2" (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Technical data
Type of basin Single Compartment Gross weight 5 kg Type of waste kit 3 1/2" crumb cup strainer Faucet ledge no Undercoated yes Waste hole position centre back Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
303
Type 316 Laboratory Sinks S6810/316P-1
Single compartment self rimming drop-in sink less faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 18 1/8" (460 mm) Overall left to right: 20 1/8" (511 mm) Bowl front to back: 16" (406 mm) Bowl left to right: 18" (457 mm) Bowl depth: 10" (254 mm) S6810/316P-1 center waste location, 3 1/2" (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Technical data
Type of basin Single Compartment Gross weight 6.4 kg Type of waste kit 3 1/2" crumb cup strainer Faucet ledge no Undercoated yes Waste hole position centre Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
304
Type 316 Laboratory Sinks S6810/316P-1
Single compartment self rimming drop-in sink less faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 18 1/8" (460 mm) Overall left to right: 20 1/8" (511 mm) Overall height: 10" (254 mm) Bowl front to back: 16" (406 mm) Bowl left to right: 18" (457 mm) Bowl depth: 10" (254 mm) S6810/316P-3 left rear waste location, 1 1/2" (38mm) type 316 (EN1.4401 17/12/2) stainless steel duplex waste assembly with rubber stopper and 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece Technical data
Type of basin Single Compartment Gross weight 8.4 kg Type of mounting counter top mounting Waste size DN 40 Waste kit included yes Faucet ledge no Bowl shape rounded rectangle Waste hole position rear left Rear upstand no Overflow no
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
305
Type 316 Laboratory Sinks LBS9407/316P-1
Single compartment self rimming drop-in sink with faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 14 5/16" (364 mm) Overall left to right: 16 5/8" (422 mm) Bowl front to back: 9 1/2" (241 mm) Bowl left to right: 14 1/2" (368 mm) Bowl depth: 7" (178 mm) LBS9407/316P-1 center waste location, 3 1/2" (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Technical data
Type of basin Single Compartment Gross weight 4.1 kg Type of waste kit 3 1/2" crumb cup strainer Faucet ledge yes Number of faucet holes 0 Undercoated yes Waste hole position centre Faucet hole diameter 1 1/2" (38 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
LBS9407/316P-1/1, 1 hole, 1 1/2" diameter LBS9407/316P-1/2, 2 hole, 1 1/2" diameter, 4" centers LBS9407/316P-1/3, 3 hole, 1 1/2" diameter, 4" centers LBS9407/316P-1, Custom (non-returnable)
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
306
Type 316 Laboratory Sinks LBS9407/316P-3
Single compartment self rimming drop-in sink with faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 14 5/16" (364 mm) Overall left to right: 16 5/8" (422 mm) Bowl front to back: 9 1/2" (241 mm) Bowl left to right: 14 1/2" (368 mm) Bowl depth: 7" (178 mm) LBS9407/316P-3 center waste location, 1 1/2" (38mm) type 316 (EN1.4401 17/12/2) stainless steel duplex waste assembly with rubber stopper and 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece Technical data
Type of basin Single Compartment Gross weight 4.1 kg Type of waste kit 1 1/2" duplex waste with rubber stopper Faucet ledge yes Number of faucet holes 0 Undercoated yes Waste hole position centre Faucet hole diameter 1 1/2" (38 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
LBS9407/316P-3/1, 1 hole, 1 1/2" diameter LBS9407/316P-3/2, 2 hole, 1 1/2" diameter, 4" centers LBS9407/316P-3, Custom (non-returnable)
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
307
Type 316 Laboratory Sinks LBS9407/316P-3
Single compartment self rimming drop-in sink with faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 14 5/16" (364 mm) Overall left to right: 16 5/8" (422 mm) Bowl front to back: 9 1/2" (241 mm) Bowl left to right: 14 1/2" (368 mm) Bowl depth: 7" (178 mm) LBS9407/316P-3 center waste location, 1 1/2" (38mm) type 316 (EN1.4401 17/12/2) stainless steel duplex waste assembly with rubber stopper and 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece Technical data
Type of basin Single Compartment Gross weight 4.1 kg Type of waste kit 1 1/2" duplex waste with rubber stopper Faucet ledge yes Number of faucet holes 0 Undercoated yes Waste hole position centre Faucet hole diameter 1 1/2" (38 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
LBS9407/316P-3/1, 1 hole, 1 1/2" diameter LBS9407/316P-3/2, 2 hole, 1 1/2" diameter, 4" centers LBS9407/316P-3, Custom (non-returnable)
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
308
Type 316 Laboratory Sinks LBS4607/316P-1
Single compartment self rimming drop-in sink with faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 18 13/16" (478 mm) Overall left to right: 18 1/8" (460 mm) Bowl front to back: 14" (356 mm) Bowl left to right: 16" (406 mm) Bowl depth: 7" (178 mm) LBS4607/316P-1 center waste location, 3 1/2" (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Technical data
Type of basin Single Compartment Gross weight 4.1 kg Type of waste kit 3 1/2" crumb cup strainer Faucet ledge yes Number of faucet holes 0 Undercoated yes Waste hole position centre Faucet hole diameter 1 1/2" (38 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
LBS4607/316P-1/1, 1 hole, 1 1/2" diameter LBS4607/316P-1/3, 3 hole, 1 1/2" diameter, 4" centers, 8" centreset LBS4607/316P-1, Custom (non-returnable)
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
309
Type 316 Laboratory Sinks LBS4607/316P-3
Single compartment self rimming drop-in sink with faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 18 13/16" (478 mm) Overall left to right: 18 1/8" (460 mm) Bowl front to back: 14" (356 mm) Bowl left to right: 16" (406 mm) Bowl depth: 7" (178 mm) LBS4607/316P-3 center waste location, 1 1/2" (38mm) type 316 (EN1.4401 17/12/2) stainless steel duplex waste assembly with rubber stopper and 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece Technical data
Type of basin Single Compartment Gross weight 4.1 kg Type of waste kit 1 1/2" duplex waste with rubber stopper Faucet ledge yes Number of faucet holes 0 Undercoated yes Waste hole position centre Faucet hole diameter 1 1/2" (38 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
LBS4607/316P-3/1, 1 hole, 1 1/2" diameter LBS4607/316P-3/3, 3 hole, 1 1/2" diameter, 4" centers, 8" centreset LBS4607/316P-3, Custom (non-returnable)
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
310
Type 316 Laboratory Sinks LBS4610/316P-1
Single compartment self rimming drop-in sink with faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 18 13/16" (478 mm) Overall left to right: 18 1/8" (460 mm) Bowl front to back: 14" (356 mm) Bowl left to right: 16" (406 mm) Bowl depth: 10" (254 mm) LBS4610/316P-1 center waste location, 3 1/2" (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Technical data
Type of basin Single Compartment Gross weight 6.4 kg Type of waste kit 3 1/2" crumb cup strainer Faucet ledge yes Number of faucet holes 0 Undercoated yes Waste hole position centre Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
LBS4610/316P-1/1, 1 hole 1 1/2" diameter LBS4610/316P-1/2, 2 hole 1" diameter 2 3/4" centreset LBS4610/316P-1/3, 3 hole 1 1/2" diameter, 8" centreset
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
311
Type 316 Laboratory Sinks LBS4610/316PC-3
Single compartment self rimming drop-in sink with faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 18 13/16" (478 mm) Overall left to right: 18 1/8" (460 mm) Bowl front to back: 14" (356 mm) Bowl left to right: 16" (406 mm) Bowl depth: 10" (254 mm) LBS4610/316PC-3 center waste location, 1 1/2" (38mm) type 316 (EN1.4401 17/12/2) stainless steel duplex waste assembly with rubber stopper and 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece Technical data
Type of basin Single Compartment Gross weight 4.9 kg Type of waste kit 1 1/2" duplex waste with rubber stopper Faucet ledge yes Number of faucet holes 0 Undercoated yes Waste hole position centre Faucet hole diameter 1 1/2" (38 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
LBS4610/316PC-3/1, 1 hole, 1 1/2" diameter LBS4610/316PC-3/2, 2 hole, 1 1/2" diameter, 2 3/4" centerset LBS4610/316PC-3/3, 3 hole, 1 1/2" diameter, 4" centers, 8" centerset LBS4610/316PC-3, Custom (non-returnable)
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
312
Type 316 Laboratory Sinks LBS6407/316P-1
Single compartment self rimming drop-in sink with faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 20 9/16" (522 mm) Overall left to right: 16 1/8" (410 mm) Bowl front to back: 16" (406 mm) Bowl left to right: 14" (356 mm) Bowl depth: 7" (178 mm) LBS6407/316P-1 center back waste location, 3 1/2" (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Technical data
Type of basin Single Compartment Gross weight 4.2 kg Type of waste kit 3 1/2" crumb cup strainer Faucet ledge yes Number of faucet holes 0 Undercoated yes Waste hole position centre back Faucet hole diameter 1 1/2" (38 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
LBS6407/316P-1/1, 1 hole, 1 1/2" diameter LBS6407/316P-1/3, 3 hole, 1 1/2" diameter, 4" centers, 8" centreset LBS6407/316P-1, Custom (non-returnable)
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
313
Type 316 Laboratory Sinks LBS6407/316P-3
Single compartment self rimming drop-in sink with faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 20 9/16" (522 mm) Overall left to right: 16 1/8" (410 mm) Bowl front to back: 16" (406 mm) Bowl left to right: 14" (356 mm) Bowl depth: 7" (178 mm) LBS6407/316P-3 center back waste location, 1 1/2" (38mm) type 316 (EN1.4401 17/12/2) stainless steel duplex waste assembly with rubber stopper and 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece Technical data
Type of basin Single Compartment Gross weight 4.2 kg Type of waste kit 1 1/2" duplex waste with rubber stopper Faucet ledge yes Number of faucet holes 0 Undercoated yes Waste hole position centre back Faucet hole diameter 1 1/2" (38 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
LBS6407/316P-3/1, 1 hole, 1 1/2" diameter LBS6407/316P-3/3, 3 hole, 1 1/2" diameter, 4" centers, 8" centreset LBS6407/316P-3, Custom (non-returnable)
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
314
Type 316 Laboratory Sinks ALBS6805/316P-1
Single compartment self rimming drop-in sink with faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 20 9/16" (522 mm) Overall left to right: 20 1/8" (511 mm) Bowl front to back: 16" (406 mm) Bowl left to right: 18" (457 mm) Bowl depth: 5" (127 mm) ALBS6805/316P-1 Wheelchair accessible - Meets ADA (Americans with disabilities act guidelines), ANSI A117.1 (Accessible and usable buildings and facilities), and CSA B651-04 (Accessible design for the built environment). Check local codes to ensure compliance. Left rear waste location, 3 1/2" (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Technical data
Type of basin Single Compartment Gross weight 4.7 kg Type of mounting drop in Type of waste kit 3 1/2" crumb cup strainer Faucet ledge yes Number of faucet holes 0 Undercoated yes Waste hole position rear left Faucet hole diameter 1 1/2" (38 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), wheelchair compliant, cUPC approval Model options
ALBS6805/316P-1/1, 1 hole, 1 1/2" diameter ALBS6805/316P-1/3, 3 hole, 1 1/2" diameter, 4" centers, 8" centreset ALBS6805/316P-1, Custom (non-returnable)
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
315
Type 316 Laboratory Sinks LBS6807/316P-1
Single compartment self rimming drop-in sink with faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 20 1/2" (521 mm) Overall left to right: 20" (508 mm) Bowl front to back: 16" (406 mm) Bowl left to right: 18" (457 mm) Bowl depth: 7" (178 mm) LBS6807/316P-1 center back waste location, 3 1/2" (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Technical data
Type of basin Single Compartment Gross weight 5 kg Type of waste kit 3 1/2" crumb cup strainer Faucet ledge yes Number of faucet holes 0 Undercoated yes Waste hole position centre back Faucet hole diameter 1 1/2" (38 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
LBS6807/316P-1/1, 1 hole, 1 1/2" diameter LBS6807/316P-1/3, 3 hole, 1 1/2" diameter, 4" centers, 8" centreset LBS6807/316P-1, Custom (non-returnable)
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
316
Type 316 Laboratory Sinks LBS6808/316P-1
Single compartment self rimming drop-in sink with faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 20 1/2" (521 mm) Overall left to right: 20" (508 mm) Bowl front to back: 16" (406 mm) Bowl left to right: 18" (457 mm) Bowl depth: 8" (203 mm) LBS6808/316P-1 center back waste location, 3 1/2" (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Technical data
Type of basin Single Compartment Gross weight 5.5 kg Type of waste kit 3 1/2" crumb cup strainer Faucet ledge yes Number of faucet holes 0 Undercoated yes Waste hole position centre back Faucet hole diameter 1 1/2" (38 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
LBS6808/316P-1/1, 1 hole, 1 1/2" diameter LBS6808/316P-1/3, 3 hole, 1 1/2" diameter, 4" centers, 8" centreset LBS6808/316P-1, Custom (non-returnable)
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
317
Type 316 Laboratory Sinks LBS6810/316P-1
Single compartment self rimming drop-in sink with faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 20 9/16" (522 mm) Overall left to right: 20 1/8" (511 mm) Bowl front to back: 16" (406 mm) Bowl left to right: 18" (457 mm) Bowl depth: 10" (254 mm) LBS6810/316P-1 center waste location, 3 1/2" (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Technical data
Type of basin Single Compartment Gross weight 6 kg Type of waste kit 3 1/2" crumb cup strainer Faucet ledge yes Number of faucet holes 0 Undercoated yes Waste hole position centre Faucet hole diameter 1 1/2" (38 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
LBS6810/316P-1/1, 1 hole, 1 1/2" diameter LBS6810/316P-1/3, 3 hole, 1 1/2" diameter, 4" centers, 8" centreset LBS6810/316P-1, Custom (non-returnable)
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
318
Type 316 Laboratory Sinks LBS6810/316P-3
Single compartment self rimming drop-in sink with faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 20 9/16" (522 mm) Overall left to right: 20 1/8" (511 mm) Bowl front to back: 16" (406 mm) Bowl left to right: 18" (457 mm) Bowl depth: 10" (254 mm) LBS6810/316P-3 left rear waste location, 1 1/2" (38mm) type 316 (EN1.4401 17/12/2) stainless steel duplex waste assembly with rubber stopper and 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece Technical data
Type of basin Single Compartment Gross weight 6 kg Type of waste kit 1 1/2" duplex waste with rubber stopper Faucet ledge yes Number of faucet holes 0 Undercoated yes Waste hole position rear left Faucet hole diameter 1 1/2" (38 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
LBS6810/316P-3/1, 1 hole, 1 1/2" diameter LBS6810/316P-3/3, 3 hole, 1 1/2" diameter, 4" centers, 8" centreset LBS6810/316P-3, Custom (non-returnable)
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
319
Type 316 Laboratory Sinks D6410/316PCB-1
Double compartment self rimming drop-in sink less faucet ledge. 18 gauge (1.2mm), type 316 (CNS 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fittings, factory applied rim seal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.32008 / CSA B45.4-08. Overall front to back: 18 1/8" (460 mm) Overall left to right: 31 1/4" (794 mm) Bowl front to back: 16" (406 mm) Bowl left to right: 14" (356 mm) Bowl depth: 10" (254 mm) D6410/316PCB-1 center back waste location, 3 1/2" (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Technical data
Type of basin Double Compartment Gross weight 8.6 kg Type of waste kit 3 1/2" crumb cup strainer Faucet ledge no Undercoated yes Waste hole position centre back Spillway yes Faucet hole diameter 1 1/2" (38 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
320
Type 316 Laboratory Sinks LBD6407/316P-1
Double compartment self rimming drop-in sink with faucet ledge. Center back waste location. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes factory applied rim seal, factory installed EZ TORQUE™ fasteners and 3 1/2" (89mm) crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 20 1/2" (520 mm) Overall left to right: 31 1/4" (794 mm) Bowl front to back: 16" (406 mm) Bowl left to right: 14" (356 mm) Bowl depth: 7" (178 mm) LBD6407/316P-1 7" (178mm) deep, centre back waste location, 3 1/2" (89mm) type 316 crumb cup waste Technical data
Type of basin Double Compartment Gross weight 8 kg Type of waste kit 3 1/2" crumb cup strainer Faucet ledge yes Number of faucet holes 0 Undercoated yes Waste hole position centre back Spillway yes Faucet hole diameter 1 1/2" (38 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
LBD6407/316P-1/1, 1 hole, 1 1/2" diameter LBD6407/316P-1/3, 3 hole, 1 1/2" diameter, 4" centers, 8" centreset LBD6407/316P-1/4, 4 hole, as 3 hole above, plus 1 hole 4" to the right LBD6407/316P-1, Custom (non-returnable)
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
321
Type 316 Laboratory Sinks LBD6408/316P-1
Double compartment self rimming drop-in sink with faucet ledge. Center back waste location. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes factory applied rim seal, factory installed EZ TORQUE™ fasteners and 3 1/2" (89mm) crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 20 1/2" (520 mm) Overall left to right: 31 1/4" (794 mm) Bowl front to back: 16" (406 mm) Bowl left to right: 14" (356 mm) Bowl depth: 8" (203 mm) LBD6408/316P-1 8" (203mm) deep, centre back waste location, 3 1/2" (89mm) type 316 crumb cup waste Technical data
Type of basin Double Compartment Gross weight 8.5 kg Type of waste kit 3 1/2" crumb cup strainer Faucet ledge yes Number of faucet holes 0 Undercoated yes Waste hole position centre back Spillway yes Faucet hole diameter 1 1/2" (38 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
LBD6408/316P-1/1, 1 hole, 1 1/2" diameter LBD6408/316P-1/3, 3 hole, 1 1/2" diameter, 4" centers, 8" centreset LBD6408/316P-1/4, 4 hole, as 3 hole above, plus 1 hole 4" to the right LBD6408/316P-1, Custom (non-returnable)
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
322
Type 316 Laboratory Sinks LBD6410/316PCB-1
Double compartment self rimming drop-in sink with faucet ledge. Center back waste location. 18 gauge (1.2mm), type 316 (EN1.4401 18/10) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes factory applied rim seal, factory installed EZ TORQUE™ fasteners, and waste kit. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Overall front to back: 20 13/16" (529 mm) Overall left to right: 31 1/4" (794 mm) Bowl front to back: 16" (406 mm) Bowl left to right: 14" (356 mm) Bowl depth: 10" (254 mm) LBD6410/316PCB-1 center back waste location, includes 3 1/2" (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Technical data
Type of basin Double Compartment Gross weight 9.3 kg Type of waste kit 3 1/2" crumb cup strainer Faucet ledge yes Number of faucet holes 0 Undercoated yes Waste hole position centre back Spillway yes Faucet hole diameter 1 1/2" (38 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
LBD6410/316PCB-1/1, 1 hole, 1 1/2" diameter, centered over partition LBD6410/316PCB-1/3, 3 hole, 8" centerset, 1 1/2" diameter, centered over partition LBD6410/316PCB-1/X, Custom (non-returnable)
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
323
Type 316 Laboratory Sinks UCS4608/316P-1
Single compartment undermount sink. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, cutout template, and installation hardware. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Center waste location, 3 1/2" (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Overall front to back: 16 1/8" (410 mm) Overall left to right: 18 1/8" (460 mm) Overall height: 8" (203 mm) Bowl front to back: 14" (355 mm) Bowl left to right: 16" (406 mm) Bowl depth: 8" (203 mm) UCS4608/316P-1 Technical data
Type of basin Single Compartment Gross weight 6.8 kg Type of mounting undermount Waste size DN 40 Waste kit included yes Faucet ledge no Bowl shape rounded rectangle Waste hole position centre Rear upstand no Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
324
Type 316 Laboratory Sinks UCS4610/316P-1
Single compartment undermount sink. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, cutout template, and installation hardware. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Center waste location, 3 1/2" (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Overall front to back: 16 1/8" (410 mm) Overall left to right: 18 1/8" (460 mm) Bowl front to back: 14" (356 mm) Bowl left to right: 16" (406 mm) Bowl depth: 10" (254 mm) UCS4610/316P-1 Technical data
Type of basin Single Compartment Gross weight 4.8 kg Type of mounting undermount Type of waste kit 3 1/2" crumb cup strainer Faucet ledge no Undercoated yes Waste hole position centre Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
325
Type 316 Laboratory Sinks UCS6808/316P-1
Single compartment undermount sink. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, cutout template, and installation hardware. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Center back waste location, 3 1/2" (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Overall front to back: 17 3/4" (451 mm) Overall left to right: 19 3/4" (502 mm) Bowl front to back: 16" (406 mm) Bowl left to right: 18" (457 mm) Bowl depth: 8" (203 mm) UCS6808/316P-1 Technical data
Type of basin Single Compartment Gross weight 4.8 kg Type of mounting undermount Type of waste kit 3 1/2" crumb cup strainer Faucet ledge no Undercoated yes Waste hole position centre back Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
326
Type 316 Laboratory Sinks UCS6810/316P-1
Single compartment undermount sink. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, cutout template, and Universal Installation System hardware. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Center waste location, 3 1/2" (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Overall front to back: 18 1/8" (460 mm) Overall left to right: 20 1/8" (511 mm) Bowl front to back: 16" (406 mm) Bowl left to right: 18" (457 mm) Bowl depth: 10" (254 mm) UCS6810/316P-1 Technical data
Type of basin Single Compartment Gross weight 6.4 kg Type of mounting undermount Type of waste kit 3 1/2" crumb cup strainer Faucet ledge no Undercoated yes Waste hole position centre Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
327
Type 316 Laboratory Sinks Classic Series - 16 gauge
Single compartment scullery sink. 16 gauge (1.5mm), type 316 (EN1.4401 17/12/2) stainless steel. Polished to a #4 satin finish. Radius coved bowl corners. Rolled rim. Sink compartment sloped to drain. Stainless Steel tubular legs with adjustable feet. Type 316 (EN1.4401 17/12/2) waste fitting included. Certified to ASME A112.19.3-2008 / CSA B45.4-08. This series of scullery sinks are built to order and are non-returnable. Backsplash 9" (230 mm) Waste size -1 = 3 1/2" (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. -5 = 1 1/2" (38mm) type 316 (EN1.4401 17/12/2) stainless steel duplex waste assembly with rubber stopper and 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece with standpipe and guard Faucet hole options (Standard) Standard drilling is one set of 2 hole, 1 1/4" (32mm) diameter, 8" (203mm) centerset. Punched 4" (102mm) below top of backsplash. Floor to work surface 35" (890 mm)
Project Information Project Name Item Reference Location Quote # Faucet Model # Drawing shown with a "-1" waste
Drillings Required Notes
Single Compartment - without drainboard Overall Dimensions Model
Sink Compartment Dimensions
A (Front-Back)
B (Left-Right)
C (Front-Back)
D (Left-Right)
E (Depth)
F Backsplash
SL2424/316-1
27 3/16" (691 mm)
27 3/16" (691 mm)
24" (610 mm)
24" (610 mm)
14" (356 mm)
SL2424/316-5
27 3/16" (691 mm)
27 3/16" (691 mm)
24" (610 mm)
24" (610 mm)
14" (356 mm)
SL2448/316-1
27 3/16" (691 mm)
51 3/8" (1305 mm)
24" (610 mm)
48" (1219 mm)
SL2448/316-5
27 3/16" (691 mm)
51 3/8" (1305 mm)
24" (610 mm)
48" (1219 mm)
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
Waste Location
Faucet Holes
9" (229 mm)
C
2
9" (229 mm)
RR
2
14" (356 mm)
9" (229 mm)
C
2
14" (356 mm)
9" (229 mm)
RR
2
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
328
Type 316 Laboratory Sinks Art Room - 18 gauge
Single compartment self rimming drop-in sink without faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Center waste location, 3 1/2" (89mm) type 316 (EN1.4401 17/12/2) stainless steel crumb cup strainer with 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Technical data
Type of basin Single Compartment Gross weight 16.4 kg (ART36/316-1) Gross weight 17.7 kg (ART48/316-1) Gross weight 19.1 kg (ART60/316-1) Type of mounting drop in Type of waste kit 3 1/2" crumb cup strainer Faucet ledge no Undercoated yes Waste hole position centre Faucet hole diameter 1 1/2" (38 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
Type 316 - 18 gauge Overall Dimensions Model
A (Front-Back)
Sink Compartment Dimensions
B (Left-Right)
C (Front-Back)
D (Left-Right)
E (Depth)
F Backsplash
Waste Location
Faucet Holes
ART36/316-1
19 1/8" (486 mm)
38 1/8" (969 mm)
17" (432 mm)
36" (914 mm)
8" (203 mm)
N/A
C
N/A
ART48/316-1
19 1/8" (486 mm)
50 1/8" (1273 mm)
17" (432 mm)
48" (1219 mm)
8" (203 mm)
N/A
C
N/A
ART60/316-1
19 1/8" (486 mm)
62 1/8" (1578 mm)
17" (432 mm)
60" (1524 mm)
8" (203 mm)
N/A
C
N/A
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
329
Type 316 Laboratory Sinks Art Room - 18 gauge
Single compartment self rimming drop-in sink without faucet ledge. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fitting, factory applied rim seal, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Center waste location, 1 1/2" (38mm) type 316 (EN1.4401 17/12/2) stainless steel duplex waste assembly with rubber stopper and 1 1/2" (DN38) type 316 (EN1.4401 17/12/2) stainless steel tailpiece. Technical data
Type of basin Single Compartment Gross weight 16.4 kg (ART36/316-3C) Gross weight 17.7 kg (ART48/316-3C) Gross weight 19.1 kg (ART60/316-3C) Type of mounting counter top mounting Waste size DN 40 Waste kit included yes Faucet ledge no Bowl shape rectangle Waste hole position centre Rear upstand no Overflow no
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
Type 316 - 18 gauge Overall Dimensions Model
A (Front-Back)
Sink Compartment Dimensions
B (Left-Right)
C (Front-Back)
D (Left-Right)
E (Depth)
F Backsplash
Waste Location
Faucet Holes
ART36/316-3C
19 1/8" (486 mm)
38 1/8" (969 mm)
17" (432 mm)
36" (914 mm)
8" (203 mm)
N/A
C
N/A
ART48/316-3C
19 1/8" (486 mm)
50 1/8" (1273 mm)
17" (432 mm)
48" (1219 mm)
8" (203 mm)
N/A
C
N/A
ART60/316-3C
19 1/8" (486 mm)
62 1/8" (1578 mm)
17" (432 mm)
60" (1524 mm)
8" (203 mm)
N/A
C
N/A
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
330
Type 316 Laboratory Sinks LBSDBL6810/316P-1
Single compartment self rimming drop-in sink with faucet ledge and drain board. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Waste fittings included. Certified to ASME A112.19.32008 / CSA B45.4-08. Note: Please allow 4 weeks for delivery. Overall front to back: 20 9/16" (522 mm) Overall left to right: 40" (1016 mm) Bowl front to back: 16" (406 mm) Bowl left to right: 18" (457 mm) Bowl depth: 10" (254 mm) LBSDBL6810/316P-1 Drain board is located to the left of sink bowl and is sloped for drainage, center waste location, includes 3 1/2" (89mm) crumb cup strainer with 1 1/2" (DN38) brass tailpiece Technical data
Type of basin Single Compartment Gross weight 9.5 kg Type of waste kit 3 1/2" crumb cup strainer Faucet ledge yes Number of faucet holes 3 Undercoated yes Waste hole position centre Faucet hole diameter 1 1/2" (38 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
LBSDBL6810/316-1/1, 1 hole, 1 1/2" diameter LBSDBL6810/316-1/3, 3 hole, 1 1/2" diameter, 4" centers, 8" centerset LBSDBL6810/316-1, Custom (non-returnable)
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
331
Type 316 Laboratory Sinks LBSDBR6810/316P-1
Single compartment self rimming drop-in sink with faucet ledge and drain board. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Waste fittings included. Certified to ASME A112.19.32008 / CSA B45.4-08. Note: Please allow 4 weeks for delivery. Overall front to back: 20 5/8" (524 mm) Overall left to right: 40" (1016 mm) Bowl front to back: 16" (406 mm) Bowl left to right: 18" (457 mm) Bowl depth: 10" (254 mm) LBSDBR6810/316P-1 Drain board is located to the right of sink bowl and is sloped for drainage, center waste location, includes 3 1/2" (89mm) crumb cup strainer with 1 1/2" (DN38) brass tailpiece Technical data
Type of basin Single Compartment Gross weight 9.5 kg Type of waste kit 3 1/2" crumb cup strainer Faucet ledge yes Number of faucet holes 3 Undercoated yes Waste hole position centre Faucet hole diameter 1 1/2" (38 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
LBSDBR6810/316-1/1, 1 hole, 1 1/2" diameter LBSDBR6810/316-1/3, 3 hole, 1 1/2" diameter, 4" centers, 8" centerset LBSDBR6810/316-1, Custom (non-returnable)
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
332
Type 316 Laboratory Sinks OC6/316
Single bowl commercial laboratory sink. 20 gauge (0.9mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are sand-blast finished. Positive hold down clamping. 1 1/2" (38mm) type 316 (EN1.4401 17/12/2) stainless steel duplex waste assembly is integral (tailpiece optional*). Certified to ASME A112.19.3-2008 / CSA B45.4-08. Center waste location These sinks do not include tailpiece. A type 316 tailpiece is available by ordering 315-9/316. Overall front to back: 4 1/2" (114 mm) Overall left to right: 7 1/2" (190 mm) Overall height: 4 1/2" (114 mm) Bowl front to back: 3" (76 mm) Bowl left to right: 6" (152 mm) Bowl depth: 3 11/16" (94 mm) OC6/316 Technical data
Type of basin laboratory sink Gross weight 15.5 kg Net weight 11.5 kg Type of mounting counter top mounting Waste size DN 40 Faucet ledge no Bowl shape oval Waste hole position centre Overflow no
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
333
Type 316 Laboratory Sinks RC5/316
Single bowl commercial laboratory sink. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are sand-blast finished. Positive hold down clamping. 1 1/2" (38mm) type 316 (EN1.4401 17/12/2) stainless steel duplex waste assembly is integral (tailpiece optional*). Certified to ASME A112.19.3-2008 / CSA B45.4-08. Center waste location. These sinks do not include tailpiece. A type 316 tailpiece is available by ordering 315-9/316. Overall front to back: 6" (152 mm) Overall left to right: 6" (152 mm) Bowl front to back: 5" (127 mm) Bowl left to right: 5" (127 mm) Bowl depth: 4 1/2" (114 mm) RC5/316 Technical data
Type of basin laboratory sink Gross weight 0.9 kg Type of waste kit threaded tailpiece Undercoated no Waste hole position centre Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
334
Type 316 Laboratory Sinks RC6/316
Single bowl commercial laboratory sink. 20 gauge (0.9mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are sand-blast finished. Positive hold down clamping. 1 1/2" (38mm) type 316 (EN1.4401 17/12/2) stainless steel duplex waste assembly is integral (tailpiece optional*). Certified to ASME A112.19.3-2008 / CSA B45.4-08. Center waste location. These sinks do not include tailpiece. A type 316 tailpiece is available by ordering 315-9/316. Overall front to back: 7 5/8" (194 mm) Overall left to right: 7 5/8" (194 mm) Bowl front to back: 6" (152 mm) Bowl left to right: 6" (152 mm) Bowl depth: 4 1/2" (114 mm) RC6/316 Technical data
Type of basin laboratory sink Gross weight 0.9 kg Type of waste kit threaded tailpiece Undercoated no Waste hole position centre Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
335
Type 316 Laboratory Sinks WHB1617/316-3
Wall hung basin. Center back waste location. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are polished #4 satin finished. Radius coved bowl corners. One piece wall hanger. Includes type 316 (EN1.4401 17/12/2) 1 1/2" (38mm) duplex waste assembly with rubber stopper. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Separate sink carrier is not required. Overall front to back: 17" (432 mm) Overall left to right: 16 1/2" (419 mm) Overall height: 9 3/4" (248 mm) Bowl front to back: 12" (305 mm) Bowl left to right: 14" (356 mm) Bowl depth: 6" (152 mm) WHB1617/316-3 no faucet hole / custom drilling Technical data
Gross weight 5 kg Type of waste kit 1 1/2" duplex waste with rubber stopper Back splash yes Undercoated no Waste hole position centre back Back splash height 3 3/4" (95 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
WHB1617/316-3/1, 1 hole, 1 1/2" diameter WHB1617/316-3/3, 3 hole, 1 1/2" diameter, 4" centerset WHB1617/316-3, Custom (non-returnable)
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
336
Type 316 Laboratory Sinks WHB1617/316-3
ROUGH-IN DETAILS
Back side of unit is open
Clips to be positioned as required
Hanger Bracket is 14 gauge galvanized steel CAN BE MOUNTED TO POURED CONCRETE OR BLOCK WALL WITHOUT THE USE OF A SINK CARRIER
The latest rough in information is supplied with each fixture. Do not rough in without first verifying dimensions. Franke Kindred Canada reserves the right to make design and specification changes without prior notice. Franke Kindred Canada will not assume any responsibility for the use of obsolete data. Please visit www.franke-commercial.com for the latest specifications. CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
337
Type 316 Laboratory Sinks WHB1819/316-3
Wall hung basin. Center back waste location. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are polished #4 satin finished. Radius coved bowl corners. One piece wall hanger. Includes type 316 (EN1.4401 17/12/2) 1 1/2" (38mm) duplex waste assembly with rubber stopper. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Separate sink carrier is not required. Overall front to back: 19" (483 mm) Overall left to right: 18 1/2" (470 mm) Overall height: 10 3/4" (273 mm) Bowl front to back: 14" (356 mm) Bowl left to right: 16" (406 mm) Bowl depth: 7" (178 mm) WHB1819/316-3 no faucet hole / custom drilling, 1 1/2" (38mm) duplex waste assembly with rubber stopper and 1 1/2" (DN38) brass tailpiece Technical data
Gross weight 6 kg Type of waste kit 1 1/2" duplex waste with rubber stopper Back splash yes Undercoated no Waste hole position centre Back splash height 3 3/4" (95 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
WHB1819/316-3/1, 1 hole, 1 1/2" diameter WHB1819/316-3/3, 3 hole, 1 1/2" diameter, 4" centerset WHB1819/316-3, Custom (non-returnable)
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
338
Type 316 Laboratory Sinks WHB1819/316-3
ROUGH-IN DETAILS
Back side of unit is open
Clips to be positioned as required
Hanger Bracket is 14 gauge galvanized steel CAN BE MOUNTED TO POURED CONCRETE OR BLOCK WALL WITHOUT THE USE OF A SINK CARRIER
The latest rough in information is supplied with each fixture. Do not rough in without first verifying dimensions. Franke Kindred Canada reserves the right to make design and specification changes without prior notice. Franke Kindred Canada will not assume any responsibility for the use of obsolete data. Please visit www.franke-commercial.com for the latest specifications. CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
339
Type 316 Laboratory Sinks
WHBS161709/316-3, WHBS161709/316-7
Wall hung basin with shroud. Center back waste location. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are #4 satin finished. Radius coved bowl corners. One piece wall hanger. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Please allow 8-10 weeks for delivery. Separate sink carrier is not required. Overall front to back: 17" (432 mm) Overall left to right: 16 1/2" (419 mm) Overall height: 13 1/2" (343 mm) Bowl front to back: 12" (305 mm) Bowl left to right: 14" (356 mm) Bowl depth: 9" (229 mm) WHBS161709/316-3 1 1/2" (38mm) waste Technical data
Gross weight 7 kg Waste size DN 40 Type of waste kit 1 1/2" duplex waste with rubber stopper Faucet ledge yes Back splash yes Undercoated no Waste hole position centre back Back splash height 3 3/4" (95 mm) Overflow no Certificates and approvals LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
WHBS161709/316-3/1 - 1 hole, 1 1/2" (38mm) diameter WHBS161709/316-3/3 - 3 hole, 1 1/4" (32mm) diameter, 4" (102mm) centerset WHBS161709/316-7 accepts 1 1/4" (32mm) waste (not included) Technical data
Project Information Project Name
Waste size DN 32 Faucet ledge yes Back splash yes Undercoated no Waste hole position centre back Back splash height 3 3/4" (95 mm) Overflow no Certificates and approvals LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
Item Reference Location
WHBS161709/316-7/1 - 1 hole, 1 1/2" (38mm) diameter WHBS161709/316-7/3 - 3 hole, 1 1/4" (32mm) diameter, 4" (102mm) centerset
Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
340
Type 316 Laboratory Sinks WHBS161709-316 SERIES
ROUGH-IN DETAILS
Back side of unit is open
Clips to be positioned as required
Hanger bracket is 14 gauge galvanized steel CAN BE MOUNTED TO POURED CONCRETE OR BLOCK WALL WITHOUT THE USE OF A SINK CARRIER
The latest rough in information is supplied with each fixture. Do not rough in without first verifying dimensions. Franke Kindred Canada reserves the right to make design and specification changes without prior notice. Franke Kindred Canada will not assume any responsibility for the use of obsolete data. Please visit www.franke-commercial.com for the latest specifications. CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
341
Type 316 Laboratory Sinks WHBS181910/316-3
Wall hung basin with shroud. Center waste location. 18 gauge (1.2mm), type 316 (EN1.4401 17/12/2) stainless steel. Exposed surfaces are polished #4 satin finished. Radius coved bowl corners. One piece wall hanger. Includes 1 1/2" (38mm) duplex waste assembly with rubber stopper. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Separate sink carrier is not required. Overall front to back: 19" (483 mm) Overall left to right: 18 1/2" (470 mm) Overall height: 14 1/4" (362 mm) Bowl front to back: 14" (356 mm) Bowl left to right: 16" (406 mm) Bowl depth: 10" (254 mm) WHBS181910/316-3 Technical data
Gross weight 8 kg Waste size DN 40 Type of waste kit 1 1/2" duplex waste with rubber stopper Back splash yes Undercoated no Waste hole position centre Back splash height 4" (102 mm) Overflow no Certificates and approvals pre-consumer recycled 31%, postconsumer-recycled 56%, LEED MR credit 4: recycled content (1-2 points), cUPC approval Model options
WHBS181910/316-3/1, 1 hole, 1 1/2" diameter WHBS181910/316-3/3, 3 hole, 1 1/2" diameter, 4" center set WHBS181910/316-3/X, custom / non-returnable, faucet holes to be specified at time of order
Project Information Project Name Item Reference Location Quote # Faucet Model # Drillings Required Notes
CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2014
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
342
Type 316 Laboratory Sinks WHBS181910-316-3
ROUGH-IN DETAILS
Back side of unit is open
Clips to be positioned as required
Hanger bracket is 14 gauge galvanized steel CAN BE MOUNTED TO POURED CONCRETE OR BLOCK WALL WITHOUT THE USE OF A SINK CARRIER
The latest rough in information is supplied with each fixture. Do not rough in without first verifying dimensions. Franke Kindred Canada reserves the right to make design and specification changes without prior notice. Franke Kindred Canada will not assume any responsibility for the use of obsolete data. Please visit www.franke-commercial.com for the latest specifications. CANADA: 1-855-446-5663 |
[email protected] 61562 | SPECIFICATIONS | 2013
USA: 1-855-526-0503 |
[email protected] www.franke-commercial.com
343
