663_ultraease_bnc-rca-pintype_is:g-1400

Transcript

Drop Connectors BNC, RCA & Pin Type “F” Compression Installation Guide Applicable Part Numbers: GA-BNC-UE-59 GA-BNC-UE-59Q GA-BNC-UE-M GA-BNC-UE-MQ GA-RCA-UE-M GA-RCA-UE-MQ GAF-UE-M GAF-UE-MQ Cable Trim Tools: 59 & 6 Series Minicoax Series GA-BNC-UE-6 GA-RCA-UE-59 GA-RCA-UE-6 GA-BNC-UE-6Q GA-RCA-UE-59Q GA-RCA-UE-6Q G-CPT-6590, G-SDT-596-250 or equivalent G-LDT-MINI Connector Compression Tools: F series: G-CAT-UNIVERSAL-FX and G-8800-US RCA & BNC series: G-CAT-MULTIMEDIA Cable Preparation 1. Prepare cable with an appropriate trim tool to dimensions shown. Fold exposed braid back over jacket. Leave foil attached to dielectric. Do not score center conductor. See Figure A. Figure A 1/4 [6.4 mm] 1/4 [6.4 mm] 1/4 [6.4 mm] Quad Shield Cables: Fold outer braid back over jacket, remove outer foil, fold inner braid back over jacket. Leave foil attached to dielectric. Do not score center conductor. 2. Use the width of the connector label as a guide for the cable center conductor trim length. Cable Installation 3. Insert the cable center conductor into socket in the rear of the connector as shown. Push the connector onto cable until the connector pin protrudes as shown in Figures B, C, & D. Figure C Figure B Pin PIN RECESSED Recessed APPROX. Approx. .430 [10.92] .430 [10.92] Figure D Pin PIN RECESSED Recessed APPROX. Approx. .100 [2.54] .100 [2.54] Pin Recessed PIN RECESSED Approx. APPROX. .271 [6.9] .271 [6.90] Before BEFORE Installation INSTALLATION BEFORE INSTALLATION Before Installation Before Installation BEFORE INSTALLATION After Cable Installation AFTER CABLE INSTALLATION Uncompressed UNCOMPRESSED AFTERCable CABLE INSTALLATION After Installation UNCOMPRESSED Uncompressed AfterUNCOMPRESSED Cable Installation Uncompressed 75 BNC 75OHM OHM MALE INTERFACE BNC Male Interface BNC RCA AFTER CABLE INSTALLATION Pin Type “F” ©2008 Corning Gilbert Inc. G-1400-663 09/08 Connector Activation 4. Fully open the compression tool. Place Silver adapter in compression tool for Pin Type “F” and RCA connectors. See Figure E for RCA and Pin Type “F.” No adapter is required for BNC connectors. 5. Slightly angle the connector/cable and insert into the compression tool area between the plunger and the cable yoke. See Figure E for all three types of connectors below. Push the cable into the cable yoke, as shown in Figure F. Compress the connector by squeezing the tool handles together until a positive stop is reached as shown in Figure G. Remove the connector/cable from the tool. BNC Note: No Adapter required Figure E RCA Figure G Note: Requires Silver Adapter Figure E Pin Type Figure F Figure F Figure G Figure F Figure G Note: Requires Silver Adapter Figure E Corning Gilbert Inc. Broadband Products 5310 W. Camelback Rd. Glendale, AZ 85301 U.S.A. phone: 800 528 5567 fax: 800 344 6358 (U.S. & Canada) (01) 623 245 1050 (01) 623 939 3538 (International) e-mail: [email protected] website: www.corning.com/corninggilbert ©2008 Corning Gilbert Inc. G-1400-663 09/08