675b

Transcript

Illustrated Parts List Rear-tine Tiller Model 675B—Pony® Model 675B Shown (bumper syles vary) IMPORTANT:READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brushcovered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available by contacting the service department at Troy-Bilt LLC, P.O. Box 361131 Cleveland, Ohio 44136-0019. TROY-BILT LLC, P.O. BOX 361131, CLEVELAND, OH 44136-0019 PRINTED IN USA FROM NO. 769-00586 (12/2002) Section 6 Parts List HANDLEBAR ASSEMBLY and CONTROL LEVERS 10 (See page 28, Ref. 47, for attachment screw) 25 Parts List Model 675B HANDLEBAR ASSEMBLY and CONTROL LEVERS REF. No. PART No. 1 2 3 3A 4 5 5A 6 7 8 9 10 13 1918811 GW-9126 777I22071 777D006865 1916639 1186347 GW-9955 1900475 710-0514 736-3050 712-3000 1918791 GW-9442 14 GW-9057 DESCRIPTION Handlebars (Incl. Refs. 2, 3 & 3A) ....... Grip ..................................................... Decal, Control Panel ........................... Decal, Model Name/Logo .................... Reverse Clutch Control Cable .............. Height Adjustment Screw ................... Washer, Keyed..................................... Bracket, Handlebar Height Adjustment Hex Hd. Screw, 3/8-16 x 1*................. Washer, Plain (flat) 3/8, S.A.E. ............ Hex Locknut, 3/8-16 ............................ Cable, Forward Clutch Control ............. Wheel Gear Control and Cable Assy. (Incl. Refs. 14, 15, 19, 21, 22 & 23) Knob, Wheel Gear Control Lever.......... * Specify GRADE 5 if ordering part locally. QTY. 1 2 1 1 1 1 1 1 2 2 2 1 1 1 REF. No. PART No. 15 16 17 19 21 22 23 24 25 1186211 710-0216 736-0169 725-0157 1114748 1100240 1186208 GW-9390 1918840 35 36 42 GW-9853 GW-20806 710-0599 DESCRIPTION Hex Nut, 5/16-24 ................................. Hex Hd. Screw, 3/8-16 x 3/4*.............. Lockwasher, 3/8 .................................. Cable Ties, Plastic................................ Round Hd. Screw, #10-32 x 1/2 .......... Lockwasher, #10 ................................. Hex Nut, #10-32 .................................. Grip ..................................................... Bail, Forward Clutch Control (Incl. two Ref. 24)..................................... Sems Nut............................................. Bracket, Bail Support ........................... Hex Flange Screw, self-tapping, 1/4-20 x 1/2* ................................... QTY. 2 2 2 2 6 2 2 2 1 4 2 2 26 Parts List Model 675B ENGINE, SUPPORT BRACKETS, PULLEYS, BELTS, BELT COVER 36 5 6 Reverse Clutch Cable 7 2 7 3 4 9 10 2 13 11 14 35 16 15 56 16 17 45 52 1 39 40 20 42 46 18 48 21 45 20 43 44 49 50 51 43 12 38 53 8 22 (Screw, Ref. 47, secures Forward Clutch Cable – page 26, Ref. 10) 44 9 47 37 54 24 25 23 26 27 30 3 28 29 41 Parts List 27 Model 675B ENGINE, SUPPORT BRACKETS, PULLEYS, BELTS, BELT COVER REF. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 PART No. 710-0395 1917326 736-0119 710-0107 777S30651 1917139 712-3004A 1108841 GW-1138-1 1916520 GW-9944 GW-9572 710-3103 1918731 1916535 1107382 1916725 710-0117 1917746 GW-9929 1916728 1916522 GW-1440 1918812 1909404 1900396 DESCRIPTION Hex Hd. Screw, 5/16–18 x 2-1/4 ......... Bracket, Clutch Cable .......................... Lockwasher–5/16................................ Hex Hd. Screw, 5/16-24 x 1/2 ............. Decal, Hot Surfaces/Belt Warning ....... Cover (Incl. Ref. 5).............................. Flange Lock Nut, 5/16-18.................... Key, 3/16 x 1-1/2 ................................ Shim ................................................... Pulley, Engine Drive ............................ Belleville Washer................................. Hex Hd. Screw, 5/16–24 x 1-1/8 ......... Hex Hd. Screw, 5/16–18 x 2 ............... Reverse Idler Arm ............................... Pulley, Reverse Idler ........................... Flat Washer, 5/16 ................................ Belt Guide, Wire Formed .................... Hex Head Screw, 5/16-24 x 1.............. Washer, Shoulder ............................... Washer, Flat, 1-1/8.............................. Spring, Reverse Return....................... Transmission Pulley............................ Support Washer .................................. Reverse Clutch Belt ............................. Forward Clutch Belt............................. Self-tapping Screw, #10-32 x 1/2, ...... QTY. 1 1 6 2 1 1 2 1 1 1 2 1 1 1 1 2 1 1 1 3 1 1 1 1 1 4 * Specify GRADE 5 if ordering part locally. ** See your local authorized engine service dealer for engine parts or service. Refer to engine nameplate for engine type and code information. REF. No. 27 28 29 30 31 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 PART No. GW-20339 712-0267 1186329 1916797 1916796 710-0805 777I20942 1918774 GW-90063 710-3037 736-0275 1918846 GW-55088 736-0119 712-0267 1917746 1918744 1767754 1916727 712-3000 GW-9090 710-0347 712-0158 1754128 736-0463 DESCRIPTION Guard, Belts/Pulleys............................ Hex Nut, 5/16–18 ................................ Hex Flange Screw, 5/16-18 x 3/4* ...... Engine Support Bracket, left side ........ Engine Support Bracket, right side...... Hex Hd. Screw, 5/16–18 x 1-1/2 ......... Decal, Stabilization.............................. Mounting Bar ...................................... Hex Flange Screw, 5/16-18 x 1 ........... Hex Hd. Screw, 5/16-18 x 2-1/4*........ Flat Washer, 5/16' ............................... Belt Guide, Pony ................................. Pivot Bushing...................................... Lockwasher, 5/16................................ Hex Nut, 5/16-18................................. Washer, Shoulder ............................... Idler Arm, Forward Tiller Direction ...... Screw, self tapping, #10-24 ................ Spring ................................................. Hex Locknut, 5/16-18 ......................... Idler Pulley, Forward .......................... Screw, 3/8-16 x 1-3/4 ......................... Hex Lock Nut, 5/16-18 ........................ Screw, 1/4-20 x 3/4 ............................ Flat Washer–1/4 .................................. QTY. 1 4 4 1 1 5 1 2 4 1 1 2 2 2 2 2 1 1 1 1 1 1 1 1 1 28 Parts List Model 675B TRANSMISSION HOUSING, COVERS, SEALS, GASKETS, PLUGS NOTE 1: These screws are a special sealing screw that cannot be reused without risking the loss of transmission oil. If these screws are loosened or removed, they must be replaced with new screws. REF. No. PART No. 1 2 3 4 5 6 721-04035 1105620 721-04001 1186329 1983632 GW-11513 7 8 9 10 11 12 GW-20694 619-04010 GW-9467 1917101 721-04035 710-04049 DESCRIPTION Oil Seal (Double Lip), Wheel Shaft ...... Pipe Plug, 1/4, ................................... Seal, Transmission Bore ..................... Hex Flange Screw, 5/16-18 x 3/4* ...... Oil Seal, Input Pinion Shaft ................. Transmission Cover (Incl. four Ref. 18 and two ea. Refs. 21 & 22).............. Gasket, Transmission Top Cover ........ Transmission Case Assy. .................... Plug .................................................... Mounting Plate, Wheel Clutch Cable ... Oil Seal, Tiller Shaft............................. Hex Flange Screw, 5/16-18 x 5/8* ...... * Specify GRADE 5 if ordering part locally. A/R – As Required QTY. 2 2 1 6 1 1 1 1 1 1 2 2 REF. No. PART No. 13 14 GW-20873 GW-1129-1 15 1915089 16 17 GW-1115 GW-1124-2 18 19 GW-90063 1915087 21 22 736-0169 710-0216 DESCRIPTION Tiller Housing Cover, left side ............. Gasket, Tiller Housing Cover, .010" (fits all covers) ................................ Screw Kit: Incl. three 1/4-20 x 7/8 Self-Sealing Screws ........................ Rear Bearing Cap ................................ Gasket, Rear Bearing Cap, .010" Thick ............................................... Hex Flange Screw, 5/16-18 x 1* ......... Screw Kit: Incl. five 1/4-20 x 5/8 Self-Sealing Screws ........................ Lockwasher, 3/8.................................. Hex Hd. Screw, 3/8-16 x 3/4* ............. QTY. 1 A/R A/R 1 A/R 4 A/R 2 2 Parts List 29 Model 675B DRIVE SHAFT, INPUT PINION SHAFT and GEAR ASSEMBLIES REF. No. PART No. 1 2 3 4 GW-1714 GW-20718 GW-9301 1916597 5 GW-1224-1 5 GW-1224-2 5 GW-1224-3 ... GW-1325C DESCRIPTION QTY. REF. No. MAIN DRIVE SHAFT Bearing, Tapered Roller with Race .... Spur Gear .......................................... Key, 3/16 sq. x 1 ............................... Main Drive Shaft (Drive shaft is onepiece with integral, single-lead, work-hardened front worm, and integral, six-lead, work-hardened rear worm. Also includes pressedon GW-1714 and GW-9301).......... Shim, Rear Bearing Cap, .010" thick (see Note below) ........................... Shim, same as above, but .030" thick (see Note)...................................... Shim, same as above, but .005" thick (see Note)...................................... Shim Set (Incl. two GW-1224-1; two 1224-2 and one GW-1224-3) ........ PART No. DESCRIPTION QTY. INPUT PINION SHAFT & GEAR ASSEMBLY 1 1 1 6 7 GW-9572 GW-9944 A/R 8 9 10 11 12 13 14 15 16 17 18 19 1108841 1916522 GW-1440 721-04044 1113527 GW-9953 GW-9428 GW-9677 GW-20791 GW-20792 GW-9093 GW-20799 A/R 20 GW-9517 1 A/R A/R Hex Hd. Screw, 5/16-24 x 1-1/8* ...... 1 Washer, Disc Spring (concave surface faces pulley)...................... 1 Key, 3/16 sq. x 1-1/2 ......................... 1 Transmission Drive Pulley................. 1 Support Washer ................................ 1 Oil Seal, Input Pinion Shaft................ 1 Retaining Ring (external) .................. 1 Thrust Washer................................... 2 Bushing ............................................. 1 Set Screw, 5/16-18 x 3/8*................. 1 Input Pinion (steel shaft)................... 1 Input Pinion Gear .............................. 1 Retaining Ring (external) l................. 1 Pinion Assy. (Incl. one each Refs. 16, 17 and 18 ...................................... A/R Retaining Ring (internal) .................. 1 NOTE: Shim between drive shaft rear bearing and rear bearing cap to achieve 5-to-10 thousandths of an inch (.005-.010) end play on drive shaft. A/R - As Required * Specify GRADE 5 if ordering part locally. 30 Parts List Model 675B WHEEL SHAFT, ECCENTRIC SHAFT and TILLER SHAFT ASSEMBLIES REF. No. 1 2 3 ------4 5 6 7 8 PART No. 721-04031 1909950 GW-1166-1 GW-1166-2 GW-1166-3 GW-1166-4 GW-1086 711-04091 GW-9373 GW-20914 GW-9935 DESCRIPTION Oil Seal .............................................. Retaining Ring (heavy-duty, external) Shim, 1-1/64 I.D., .062" thick ............ Shim, as above, but .030" thick ......... Shim, as above, but .015" thick ......... Shim, as above, but .010" thick ......... Bushing ............................................. Wheel Shaft (Incl. Ref. 6) .................. Hi-Pro Key, 1/4 x 1-5/16.................... Wheel Drive Worm Gear (cast-iron) .. Shim (between key and gear), 1.016 I.D. x 1.468 O.D. x .062 Thick.............................................. * Specify GRADE 5 if ordering part locally. A/R - As Required QTY. 2 2 A/R A/R A/R A/R 2 1 1 1 1 REF. No. 9 10 11 12 13 14 15 16 17 18 19 PART No. GW-20712 611-04002 GW-1442 GW-9055 721-04034 786-04001 710-3013 741-3037 711-04130 GW-1104 1904279 DESCRIPTION Wheel Drive Clutch (cast-iron) .......... Eccentric Shaft .................................. Pin, Eccentric Shaft ........................... Spring ............................................... Oil Seal .............................................. Eccentric Shaft Lever......................... Hex Hd. Screw, 1/4-20 x 1/2* ........... Ball Bearing ....................................... Tiller Shaft (Incl. Ref. 18) .................. Woodruff Key, 1/4 x 1-1/4................. Tiller Drive Worm Gear (bronze) ....... QTY. 1 1 1 1 1 1 1 2 1 1 1 31 Parts List Model 675B HOOD, BRACKET AND DEPTH REGULATOR REF. No. 1 2 3 4 5 6 7 8 9 10 11 12 PART No. 686-04021 736-0169 GW-2525 710-04049 712-0291 710-0597 GW-9384 GW-9534 1185469 1916186 GW-9120 GW-9119 DESCRIPTION Hood, Tine .......................................... Lockwasher, 3/8.................................. Bracket, Hood & Depth Regulator ....... Hex Hd. Flg. Screw, 5/16-18 x 5/8* .... Hex Lock Nut, 1/4-20 .......................... Hex Hd. Screw, 1/4-20 x 1* ................ Spring, Depth Regulator Plunger ........ Spacer................................................. Roll Pin (spiral), 1/4 x 1 ..................... Bar Assembly, Depth Adjustment........ Retaining Ring (Tolerance Ring) ......... Knob, Depth Regulator (Incl. Ref. 11) . * Specify GRADE 5 if ordering part locally. QTY. 1 2 1 2 1 1 1 1 1 1 1 1 REF. No. PART No. 13 14 15 16 18 710-3005 GW-1113-1 712-3017 GW-20775 710-0759 19 710-0599 20 21 22 23 1916700 1916701 1186328 1186391 DESCRIPTION Hex Hd. Screw, 3/8-16 x 1-1/4*.......... Bushing (spacer)................................. Hex Nut, 3/8-16................................... Drag Bar, Depth Regulator ................. Hex Hd. Screw, self-tapping, 5/16-18 x 1/2* ................................ Hex Hd. Flg. Screw, self-tapping, 1/4-20 x 1/2* .................................. Support Bracket, Left-Side .................. Support Bracket, Right-Side ............... Hex Hd. Screw, 5/16-18 x 5/8 ............. Hex Nut, 5/16-18 ................................ QTY. 2 2 2 1 2 2 2 1 6 6 32 Parts List Model 675B TINES 3 7 1 8A 3 3 2 OPERATOR POSITION 1 1 7 1 TINE SHAFT 2 5 3 3 3 7 1 ENGINE 8 1 2 DENOTES CUTTING EDGE OF TINE 5 3 1 3 WHEELS 11 12 11 9 10 12 Parts List 33 Model 675B TINES & WHEELS REF. No. PART No. 1 2 3 5 7 8 8A 1100068 1985101 1110108 710-3096 1985100 1916693 1916694 DESCRIPTION Hex Hd. Screw, 3/8-16 x 3/4* ............. Tine – right-hand ................................ Hex Lock Nut, 3/8-16 .......................... Hex Hd. Screw, 3/8-16 x 2, Grade 8.... Tine – left-hand ................................... Tine Holder, left-side........................... Tine Holder, right-side ........................ QTY. 12 3 14 2 3 1 1 REF. No. 9 10 11 12 PART No. 634-04033 634-04032 GW-9380 GW-9338 DESCRIPTION Wheel & Tire Assy., left-side ............... Wheel & Tire Assy., right-side ............ Clevis Pin, .312 x 1-3/4 long ............... Hitch Pin ............................................. IMPORTANT: LEFT and RIGHT sides of tiller are determined by standing in the operator position (BEHIND THE HOOD) and facing the direction of forward travel. MOUNT TINES SO THE CUTTING EDGE AT THE TOP OF EACH TINE FACES THE OPERATOR (TOP) LEFT-HAND TINE RIGHT-HAND TINE (BOTTOM) QTY. 1 1 2 2 34 Parts List Model 675B ROW MARKER ATTACHMENT (See Detail A) ROW MARKER ATTACHMENT – OEM-290-257 (Complete – Attaches to Furrower Attachment) DETAIL A MAIN SUPPORT/YOKE ASSEMBLY PART # 1904522001 BUMPER ATTACHMENT 20 19 23 22 21 BUMPER OEM-290-254 Parts List 35 Model 675B ROW MARKER ATTACHMENT & BUMPER ATTACHMENT REF No. PART No. DESCRIPTION QTY. Row Marker Attachment (option) – OEM-290-254 1 1904522 2 3 4 GW-1594 1904524 1904523 5 GW-9347 6 GW-9786 7 GW-1596 8 GW-9828 9 1100135 --- GW-1837 Main Support & Yoke Assy– complete. (Incl. Ref. No.'s 10,11,12,13,14,15,16,17 & 18).......... Marker Blade–blade only ................... Marker Arm–main arm ...................... Marker Arm–extension arm with stop pin ......................................... Hitch Pin–(incl. in Hardware Pkg GW-1837)...................................... Thumbscrew–1/4-20 x 1/2, not avail. sep. (see hardware pkg. GW-1837)...................................... Nut Bar–(incl. in hardware pkg GW-1837)...................................... Nut–hex, 10-24 w/attached start washers, not avail. sep. (see hardware pkg #1837) .................... Screw–round hd.,10-24 x 1, not avail. sep. (see hardware pkg GW-1837)...................................... Hardware Package–includes: one GW-9347 hitch pin (Ref. 5), two GW-9786 thumbscrews (Ref. 6), one GW-1596 nut bar (Ref. 7), two GW-9828 hex nuts (Ref. 8), two 1100135 screws (Ref. 9) ........ REF No. PART No. QTY. Row Marker Main Support & Yoke Assembly – Part #1904522001 1 1 1 1 1 10 1186349 11 12 13 14 15 16 17 18 GW-1593 GW-1592 GW-1591 GW-1590 GW-1588 GW-1589 GW-9925 1186231 Screw–hex flanged locking, 3/8-16 x 1-1/2* ............................. Stop Bar ............................................ Yoke .................................................. Tube Key–square............................... Washer–friction................................. Main Support .................................... Washer–square hole.......................... Washer–disc spring .......................... Nut–hex 3/8-16 ................................. 1 1 1 1 2 1 1 1 1 2 Bumper – OEM-290-254 1 2 2 19 20 21 22 23 --- 1918749 777S30653 710-3073 736-0119 712-0267 1918781 1 Note: Common hardware listed above as “not available separately” can be found at most hardware stores. * Specify GRADE 5 if ordering part locally. DESCRIPTION Bumper ............................................. Decal - Caution.................................. Screw–hex hd., 5/16-18 x 2-1/4*,..... Lockwasher–5/16*,........................... Nut–hex, 5/16-18*, ........................... Hardware Kit: Incl. four each of Refs. 21, 22 and 23 ....................... 1 1 4 4 4 1