Preview only show first 10 pages with watermark. For full document please download

6980 Instructions Pg 1

   EMBED


Share

Transcript

STORAGE Before storing, the tank should be emptied and cleaned. Store the vacuum indoors in a clean, dry area. TROUBLESHOOTING If the suction is too low, check to make sure the tank is empty, the filter is clean, and that the hose is properly secured and not obstructed. If the 12-volt circuit fails to operate, try the following suggestions: 1. In the event that the unit does not appear to vacuum properly, unplug it from the power supply and make sure that the receptacle is clean. Also check the vehicle’s fuse. 2. Be sure the contact points in the lighter receptacle are clean. DO NOT USE METAL TOOLS. Use only insulators, such as wood, if cleaning is needed. The adapter plug should fit firmly in the receptacle. 3. Carefully unscrew the plug’s top section. Remove and check the fuse with the proper electronic meter. If defective, replace the fuse with a 15-amp, 250-volt-rated glass fuse. This fuse is readily available at local auto parts and electronic stores. 4. Check your vehicle’s fuse panel to be certain that the fuse controlling the lighter is not worn or weak. Replace a damaged fuse with a new, properly sized and rated fuse to ensure satisfactory performance. 5. Some cigarette lighters have a separate circuit breaker located directly behind the cigarette lighter receptacle. If your lighter is not working, this circuit breaker may have blown and could require replacement. Consult your vehicle owner’s manual for replacement. SPECIFICATIONS Power Source 12-v DC Output 75 Watts Fuse 15-amp, 250-volt glass fuse Weight 4 lbs. Dimensions 7” x 6” x 12” Capacity 1 gallon (3.8L) Maximum Liquid Capacity 3 quarts (2.9L) Aervoe Industries, Inc. Gardnerville, NV 89410 • 800-227-0196 • 775-782-5687 www.aervoe.com.com • [email protected] *Max Burton is a registered trademark of Aervoe Industries, Inc. 6980; CS 11/11 Vacuum To Go 12-Volt Wet/Dry Vacuum Cleaner Operating Instruction Manual UNPACKING AND SET-UP Vacuum To Go #6980 12-volt wet/dry vacuum cleaner IMPORTANT SAFEGUARDS • Read all instructions before operating this or any electrical appliance. • Administer close supervision when running this appliance around children. • Unplug when not in use and before cleaning the unit. • Do Not immerse cord or unit in water or other liquids. • Know your Vacuum To Go vacuum cleaner. Read and understand the instructions and labels on the vacuum before operating. Use only as described in this manual. • Sparks inside of the motor can ignite flammable vapors or dust. To avoid fire or explosion do not vacuum or use near flammable or combustible liquids or gases. • Do Not vacuum anything that is burning or smoking such as cigarettes, matches or hot ashes. • To avoid health hazards from vapors or dust, do not vacuum toxic materials. • To avoid damage to your vacuum, store in an area where the temperature will not exceed 100ºF. To avoid injury, shock, or fire, never use a damaged vacuum or cord. • Do Not put any object into openings. Do not use with any opening blocked. Keep free of dust, lint, hair and anything that may reduce air flow. Keep hair, loose clothing and fingers away from openings and moving parts. • Do Not use without filter in place. • To avoid falls, use extra care when cleaning on stairs. • The use of attachments not recommended by the manufacturer may cause personal injury. • Do Not place vacuum nozzle near face, eyes or ears during operation. PARTS IDENTIFICATION Vacuum Hose Intake On/Off Button High/Low Button Handle Tank cover Cord Storage Clip Lock Tank Nozzle 12-Volt DC Plug Carpet Brush Attachment 3. Attach one of the cleaning accessories to the accessory end of the hose. 4. To attach the carrying strap, clip the strap ends to the rings on both sides of the unit. 5. Open the cord storage door and pull out the 15 ft. cord. 6. Push the 12-V DC plug on the end of the power cord into the DC receptacle in your vehicle. 7. The vacuum is ready for use. OPERATING INSTRUCTIONS Dry Pick-Up 1. 2. 3. 4. 5. Turn on by pressing the red ON/OFF button. The green ON/OFF indicator light will illuminate to confirm that power is being supplied to the unit. Vacuum using the appropriate cleaning attachment in any direction until the area is clean. You can adjust the power needed by pressing the yellow HI/LOW button. Press the ON/OFF button to turn the unit off. Wet Pick-Up/Cleaning Note: Empty tank before picking up liquid or wet debris. 1. When picking up liquid, wet debris or a combination of both, vacuum in any direction until the area is clean. 2. To avoid spillage while vacuuming, do not suck in liquid over the MAX FILL LINE marking. Handle with care when liquid is inside of the tank. If the tank tips and leaks it may cause damage to the unit. 3. Wet pick-up accessories should be washed periodically with warm, soapy water. 1. Securely insert the inlet end of the hose (the side with the longer end) into the blow/inflate hose output on the unit labeled B. 2. Attach the appropriate blower or inflator nozzel to the other end of the hose. 3. Plus in and turn on as described above. 4. Insert the inflate nozzel into inflatable, or use the blower attachment to clear debris. 5. Turn off using the ON/OFF button when done. OPERATION IN VEHICLES Crevice Tool Hose Carrying Strap 2. The filter is located on the underside of the tank cover. Ensure that the elastic is securely attached to the lip of the filter housing. BLOWING & INFLATING Blow/Inflate Hose Output Strap Attachment 1. Securely insert the inlet end of the hose (the side with the longer end) into the vacuum hose intake on the unit labeled V. Inflator & Blower Nozzles • Do not use while vehicle is moving. • Make sure that your battery is strong and in good working condition before plugging the Vacuum To Go into your vehicle’s 12-volt receptacle. • Do not use the unit if your vehicle’s electrical system is weak or damaged. • Periodically check your vehicle’s charging system for continued successful use.