Transcript
MODEL NUMBER P24-75-PH-R02
DIMENSIONS
APPLICATIONS
24VDC CV 75W PHASE
The LED power supply P24-75-PH-R02 is exclusively designed for the Light Emitting Diode(LED) lamps. It is a switch mode power supply with constant voltage output.
454g The loads indicated on the power supply must not be exceeded.
60m
m 35mm
An electronic protection circuit switches off the power supply in case of short circuit or overload in the secondary circuit, overheat as well as open circuit. After the removing of the faults, the LED power supply is resetting automatically for operation again.
SPECIFICATION
75W 24V LED DRIVER PHASE Dimming Installation Manual
180-240V ~ 50/60Hz Input voltage 0.8A Input current 24VDC Output voltage 75W MAX output power 3.75W Min. Load IP20 Protection degree Max. 90°C Case Temp tc PF>0.65 Power Factor 86% Efficiency 40A Inrush current Typ. 100-1% Dimming Range
CABLE LENGTH
EMI Emission
Vector interconnector cables are 22AWG. Use Suitable alternative cables for long runs.
This unit conforms to the directive 2014/30/EU for the electromagnetic compatibility and the low voltage directive 2014/35/EU.
Minimum dimming level may vary depending on the quantity of drivers connected to the same phase dimming input. Dimming curves may vary according to load. Suitable gauge wires must be used to prevent voltage drop in phase wires. Dimmers should be current sinking type. Dimmer must have the capability to switch off the mains power to the driver. It is recommended to wire a mock up test area before installation to ensure full compatibility between dimmers and drivers.
VENTILATION CLEARANCE
ENVIRONMENTAL CONDITIONS
Allow 50mm minimum clear airflow around drivers to protect from overheating. Do not cover.
IP20 - Suitable for Dry location.
Excessive Heat - Protect the LED Power supply against excessive heat (permissible operating temperature range -40 to 60°C)
z
Installers must ensure EMI emission do not exceed local regulated limits. Shield cables and ferrite coils can be used where applicable.
y
Reduce max. cable lengths by 10% if dimming.
lumino.lighting
12W/m 3.7W/ft Length Vector in Series Current
0.3mm² 22AWG
0.8mm² 18AWG
1.3mm² 16AWG
2.0mm² 14AWG
1m / 3.3’ 2m / 6.6’ 3m / 9.8’ 4m / 13.1’ 5m / 16.4’ 6m / 19.7’
50m 28m 17m 11m 7m 4m
50m 50m 50m 34m 22m 13m
50m 50m 50m 50m 36m 23m
50m 50m 50m 50m 50m 40m
0.5A 1.0A 1.5A 2.0A 2.5A 3.0A
*Cable lengths are based on average resistance for typical copper cables. Cable characteristics may vary according to manufacturer, temperature, copper purity, connections etc. *See Wiring&Load Limit Guide for more detail
Connect the LED lamps to the LED power supply with correct polarity according to the schematic drawing. If the LED power supply is used for purposes other than originally intended or it is connected in the wrong way, no liability can be taken over for possible damages.
180mm
90mm 50mm 50mm
x Maximum ambient temperature must not exceed 60°C
Constant voltage LED drivers can have high inrush current at power-on. Driver inrush current is many times the normal operating current. Use a suitable MCB. Type B or C MCBs are normally suitable. If inrush current is a persistant problem an inrush suppressor may be required.
!
P24-75-PH-R02 Wiring Schematic
For 0-10V Dimmable LED power supplies, make sure that your dimming controller is capable of driving these units, requries 0.15mA each unit.
Damage will be caused by incorrect input voltage or short circuit. Ensure access and sufficient free moving air space around drivers. Products and power supply gear must not be live wired.
Use approved primary and secondary cables rated for current greater or equal to circuit load. For LED power supplies with waterproof connectors, verify that the linkage between the unit and the lighting fixture is tight so that water cannot intrude into the cables.
DISCLAIMERS
DRIVER GUIDE FOR WIRING
Before commencing any installation or maintencance work, please disconnect the power supply from the utility. Ensure that is cannot be re-connected inadvertently.
L
TURN OFF POWER!
!
+ _
E
N
PRI 180-240VAC
75W 24VDC P24-75-PH-R02
Vector
Protect products from dust & paint during installation and use shielded pair of cables will be required for dimming control signal if applicable. Plan for loads, driver locations, dimming and suitable cable prior to installing. For technical assistance contact your local Lumino distributor.
SEC 24VDC
Installation must be carried out by qualified electrician. Electrical work to be conducted in accordance with local regulations. Power must be disconected prior to installation work. Ensure free-moving air space around leds and drivers. Incorrect voltage, reverse polarity or short circuit will cause damage.
The information in this document is subject to change without notice
CHECK THE WALL!
Check for latest specifications at www.lumino.lighting
24VDC OUTPUT
Copyright © 2017 LUMINO E&OE
IM-P24-75-PH-R02-R1701
* See Wiring&Load Limit Guide For Max. Cable length
180-240 VAC POWER IN
Use leading-edge phase cutting dimmer
LUMINO Lumino House, Lovet Road Harlow, Essex CM19 5TB United Kingdom T +44 (0) 1279 635411 E
[email protected]
lumino.lighting IM-P24-100-D10-R01
