8-603-834-0-cadet7 230v-eng

Transcript

CARPET EXTRACTOR Operating Instructions (USA) Bedienungsanleitung (GER) MODEL: CDT7IA CDT7IB CDT7IE CDT7IS COUNTRY AUSTRALIA BRITIAN EUROPE SWITZERLAND IPX4 Read instructions before operating the machine Bitte lesen Sie diese Anleitungen, bevor Sie die Maschine in Gebrauch nehmen AP 86038340 06/23/15 PRV NO. 98707 Prior to Serial Number: 10080230000755 Or call Manufacturer. MACHINE DATA LOG/OVERVIEW Warranty Registration Thank you for purchasing a Windsor product. Warranty registration is quick and easy. Your registration will allow us to serve you better over the lifetime of the product. To register your product go to: www.windsorind.com/WarrantyRegistration.aspx For customer assistance: 1-800-444-7654 2ENG CADET 86038340 04/26/11 TABLE OF CONTENTS Machine Data Log/Overview (English). ........1 Machine Data Log/Overview (German). .......2 Table of Contents (English) ..........................3 Table of Contents (German) .........................4 HOW TO USE THIS MANUAL How to use this Manual. ........................1-1ENG SAFETY GROUP PARTS LIST Frame Assembly..........................................5-1 Brush Assembly...........................................5-3 Pump Assembly...........................................5-5 Vacuum Shoe Assembly .............................5-9 Control Panel Assembly ..............................5-11 Solution Tank Assembly ..............................5-13 Recovery Tank Assembly............................5-15 Suggested Spare Parts ...............................5-17 EC Declaration of Conformity ......................5-18 Important Safety Instructions .................2-1ENG Hazard Intensity Level. ..........................2-2ENG Safety Label Location. ...........................2-3ENG OPERATIONS Technical Specifications. .......................3-1ENG Controls/Components ............................3-2ENG Filling the Solution Tank ........................3-5ENG Machine Operation. ...............................3-6ENG Cleaning Procedure. ..............................3-9ENG Accessory Tool Usage........................3-10ENG MAINTENANCE Periodic Maintenance ............................4-1ENG Daily/Regular Maintenance....................4-1ENG Vacuum Motor Replacement. ................4-2ENG Belt Replacement ..................................4-3ENG Solution Pump Replacement. ................4-3ENG Machine Troubleshooting ......................4-4ENG Wiring Diagram ......................................4-5 CADET 86038340 04/19/07 3ENG HOW TO USE THIS MANUAL This manual contains the following sections: - - HOW TO USE THIS MANUAL SAFETY OPERATIONS MAINTENANCE PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be ordered from authorized Windsor dealers. When placing an order for parts, the machine model and machine serial number are important. Refer to the MACHINE DATA box which is filled out during the installation of your machine. The MACHINE DATA box is located on the inside of the front cover of this manual. The SAFETY section contains important information regarding hazard or unsafe practices of the machine. Levels of hazards is identified that could result in product or personal injury, or severe injury resulting in death. The OPERATIONS section is to familiarize the operator with the operation and function of the machine. The MAINTENANCE section contains preventive maintenance to keep the machine and its components in good working condition. They are listed in this general order: - The PARTS LIST section contains assembled parts illustrations and corresponding parts list. The parts lists include a number of columns of information: - The model and serial number of your machine is on the bottom back-end of the machine. Vacuum Motor Replacement Belt Replacement Solution Pump Replacement - - REF – column refers to the reference number on the parts illustration. PART NO. – column lists the part number for the part. PRV NO. – reference number. QTY – column lists the quantity of the part used in that area of the machine. DESCRIPTION – column is a brief description of the part. SERIAL NO. FROM – column indicates the first machine the part number is applicable to. When the machine design has changed, this column will indicate serial number of applicable machine. The main illustration shows the most current design of the machine. The boxed illustrations show older designs. If column has an asterisk (*), call manufacturer for serial number. NOTES – column for information not noted by the other columns. NOTE: If a service or option kit is installed on your machine, be sure to keep the KIT INSTRUCTIONS which came with the kit. It contains replacement parts numbers needed for ordering future parts. NOTE: The number on the lower left corner of the front cover is the part number for this manual. 1-1ENG CADET 86038340 04/26/11 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. ! WARNING: To reduce the risk of fire, electric shock, or injury: Connect to a properly grounded outlet. See Grounding Instructions. Do not leave the machine unattended. Unplug machine from outlet when not in use and before maintenance or service. Use only indoors. Do not use outdoors or expose to rain. Do not allow machine to be used as a toy. Close attention is necessary when used by or near children. Use only as described in this manual. Use only manufacturer’s recommended components and attachments. Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning grounding the machine. If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water, return it to an authorized service center. Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run machine over cord. Keep cord away from heated surfaces. Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical cord. Do not handle the electrical plug or machine with wet hands. Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow. This machine is intended for cleaning carpet only. Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes. This machine is not suitable for picking up health endangering dust. Turn off all controls before unplugging. Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine near flammable fluids, dust or vapors. This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices for more than normal housekeeping purposes. Maintenance and repairs must be done by qualified personnel. If foam or liquid comes out of machine, switch off immediately. SAVE THESE INSTRUCTIONS CADET 86038340 04/19/07 2-1ENG HAZARD INTENSITY LEVEL The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: ! WARNING WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death. ! CAUTION CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property damage. FOR SAFETY: To Identify actions which must be followed for safe operation of equipment. Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating condition. Following is information that signals some potentially dangerous conditions to the operator or the equipment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on the machine. Please take the necessary steps to train the machine operating personnel. FOR SAFETY: DO NOT OPERATE MACHINE: Unless Trained and Authorized. Unless Operation Guide is Read and understood. In Flammable or Explosive areas. In areas with possible falling objects. WHEN SERVICING MACHINE: Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use Windsor approved replacement parts. 2-2ENG CADET 86038340 04/19/07 SAFETY LABEL LOCATION NOTE: These drawings indicate the location of safety labels on the CDT7//10080230. If, at any time, the labels become illegible contact your Windsor representative for prompt replacement. WARNING DECAL 86242230 PRV NO. 500009 CADET 86038340 04/19/07 2-3ENG TECHNICAL SPECIFICATIONS POWER TYPE GENERAL DIMENSIONS/WEIGHT ELECTRICAL: 230-240 V, 7 A, 50 HZ Vacuum shoe: 17” (43.18 cm) cast aluminum with spring loaded down pressure ELECTRIC VACUUM MOTOR: (1) –3 stage, 1.5 hp, 100 cfm (2.80 cubic meters/min.) Waterlift –121” (304 cm) WHEELS: (2) 10” dia. (25 cm) wheels by 2” BRUSH: (1) 15” (38.1 cm.) WEIGHT: 92lbs. (42kg) SOLUTION PUMP: 90 PSI, diaphragm style, internal bypass LENGTH: 41” (104 cm) SOLUTION CAPACITY: 7 gallons (26.5ltr) HEIGHT: 34” (86.36 cm) RECOVERY CAPACITY: 7 gallons (26.5ltr) WIDTH: 17.5” (44.45 cm) BRUSH SPEED: 1000 rpm SOLUTION SPRAY: 2 quick change jets. POWER CABLE: 50’ (12.7 m) (1mm) 34” (86.36cm) 41” (104cm) 3-1ENG 17.5” (44.45cm) CADET 86038340 11/02/10 CONTROLS/COMPONENT LOCATIONS 3 5 4 1 1. Main Handle. Used to pull and maneuver machine. 2. Electrical Cord. 3. Pump Switch. Turns on pump and enables spray. 4. Brush/Spray switch. Turns on brush motor and activates electro-valve to dispense solution to floor through jets. Intermittent, off, and continuous settings. 5. Vacuum Motor Switch. Turns on vacuum motor 6. Brush Motor Circuit Breaker. 4 amp. Breaker protecting brush motor. 7. Vacuum Motor Circuit Breaker. 7 amp. Breaker protecting vacuum motor. 8. Recovery Dump Hose. Facilitates draining dirty cleaning solution. 9. Solution Dump Hose. Facilitates draining excess cleaning solution from solution tank. 7 6 2 8 9 CADET 86038340 04/19/07 3-2ENG CONTROLS/COMPONENT LOCATIONS 1. Solution Accessory Tool Hookup. Used for various auxiliary cleaning tools. 2. Vacuum Hose Door. Used to connect various auxiliary 1-1/2 inch cleaning tool vacuum hoses. 3. Brush Height Adjustment. Used to regulate brush height from storage position to various carpet heights. 4. Recovery Tank. Used to collect dirty cleaning solution. 5. Solution Tank. Used to hold cleaning solution. 6. Recovery Tank Dome. 7. Vacuum Shoe. 8. Brush Housing. 9. Front Lifting Handle. 10. Cleaning Solution Filter. 10 1 9 2 3 6 4 5 7 8 3-3ENG CADET 86038340 04/19/07 CONTROLS/COMPONENT LOCATIONS 1. Solution Intake Cover. 2. Vacuum Intake Cover. 3. Float Shut-Off. 4. Clean-Out Opening. 5. Pour Spout. 6. Lift Handle. 6 1 2 4 6 5 3 CADET 86038340 04/19/07 3-4ENG FILLING OPERATIONS STEP 1 RECOVERY TANK Remove recovery tank SOLUTION TANK STEP 2 FILL LINE Add water 7 gal. (26.5 ltr.) 140°F (60°C) STEP 3 FILLING THE CADET NOTE: Use clean bucket of water to fill solution tank Do not put defoamer, solvents, spotter or prespray chemicals in the solution tank. 7 – 14oz. (207ml – 414ml) Add cleaning chemical Do not allow water to spill into vacuum motor inlet. Dry spillage from top of solution tank before replacing recovery tank. CHEMICALS Suitable Chemicals Alkalis Detergents Hydroxides Soaps Vinegar Non-Compatible Chemicals Aldehydes Aromatic Hydrocarbons SP Butyls Carbon Tetrachloride Clorox* Chlorinated Bleaches Chlorinated Hydrocarbons Lysol* Methyl Ethel Ketone (MEK) Perchorethylene (perc) Phenolics Trichlorethylene D-Limonene STEP 4 * Product Trademark Names 3-5ENG CADET 86038340 04/19/07 Replace recovery tank OPERATIONS STEP 1 STEP 2 STEP 3 1/8in (3mm) CORRECT Remove literature from recovery tank. Fill solution tank (see filling operations, page 3-5). Plug cord into grounded outlet. Note: Be sure dome is seated on recovery tank, and float shut-off is installed correctly. Adjust brush to proper setting. Note: For good operation the brush must skim the carpet. If circuit breaker trips raise brush to prevent damage to motor or carpet. INCORRECT STEP PUMP ON VACUUM 4 Turn on both Vacuum and Pump motor switches (“ON”=“I”). ON CADET 86038340 11/02/10 3-6ENG OPERATIONS Tip machine back by main handle to move to starting point. STEP Lower machine to floor. STEP Select intermittent or continuous switch setting to turn on brush and start solution spray. The intermittent setting requires the operator to hold the switch in the “on” position with the thumb, and is typically used in small areas where short cleaning passes are made. The continuous setting allows the operator to set the switch in the “on” position with one touch, and is typically used in large areas where long cleaning passes are made. STEP 3-7ENG 5 6 INTERMITTENT 7 CONTINUOUS CADET 86038340 04/19/07 CLEANING PROCEDURE STEP 1 STEP 2 1ft. (30cm) Release intermittent setting or turn off continuous setting on brush/spray switch approximately 1 foot before ending cleaning pass. OFF STEP 1in. (25mm) 3 SOLUTION INTAKE COVER VACUUM INTAKE COVER Start at wall closest to power outlet. Pull straight back without pushing down on handle. STEP 4 Push down on handle to raise vacuum shoe and brush before moving to the next cleaning pass. Overlap brush contact area a minimum of 1 inch on the right (close cleaning) side of machine. Overlap a minimum of 2 inches on the left (drive belt) side of machine. During operation, observe the following: The Cadet is equipped with clear internal covers to facilitate operator viewing of dirty solution and vacuum air flow. During operation, observe the vacuum intake cover. Large amounts of water or foam entering the vacuum system can damage the vacuum motor. If you notice either condition, shut down the machine immediately. Empty recovery tank and/or add defoamer to recovery tank. CADET 86038340 04/19/07 3-8ENG CLEANING PROCEDURE Use right side of machine for cleaning against walls. STEP After cleaning, turn off all controls, return brush to storage position and carefully unplug machine. STEP 5 6 OFF OFF OFF To speed drying, use a Windblower™ fan. STEP Empty recovery tank by releasing dump hose. Use a hose with cold water to clean out the recovery tank. Also drain solution tank after each use. STEP 7 8 RECOVERY DRAIN SOLUTION DRAIN 3-9ENG CADET 86038340 04/19/07 ACCESSORY TOOL USAGE STEP 1 Use only one of the following acceptable accessory tools. 86000000 – PRV NO. DDH 86031540 – PRV NO. 39504 86041180 – PRV NO. ESW 86000050 – PRV NO. SPW 86000020 – PRV NO. HT Pull back collar and insert over machine mounted fitting, then release collar to lock into place. STEP 2 PUMP VACUUM ON STEP 3 ON Lift door on front of vacuum shoe and insert 1 ½ inch hose cuff into hole. Turn on Pump and Vacuum Switch. Note: Be sure intermittent/continuous switch is in center (off) position and brush is in storage position. OFF STEP 4 Squeeze handle on accessory tool to begin cleaning. CADET 86038340 04/19/07 3-10ENG MAINTENANCE PERIODIC MAINTENANCE DAILY / REGULAR MAINTENANCE Twice a month, flush a white vinegar solution (One quart vinegar to two gallons of water) or anti-browning solution (mixed as directed) through the extractor. This will prevent build-up of alkaline residue in the system. If spray jets become clogged, remove the spray tips, wash them thoroughly, and blow-dry. Before making any adjustments or repairs to the machine, disconnect the power cord from electrical source. NOTE: Do not use pins, wire, etc. to clean nozzles as this could destroy spray pattern. Periodically inspect all hoses, electrical cables and connections on your machine. Frayed or cracked hoses should be repaired or replaced to eliminate vacuum or solution pressure loss. If the cable insulation is broken or frayed, repair or replace it immediately. Don’t take chances with electrical fire or shock. 1. Empty unused cleaning solution from the solution tank. 2. Inspect and clean filter screen in solution tank. 3. Flush pumping system with 4 or 7 liters of clean, hot water. 4. After each use, rinse tank with fresh water. Periodically inspect the recovery tank and decontaminate if necessary, using a Hospital Grade Virucide or a 1-10 bleach to water solution. Waste water should be disposed of properly. 5. Check for and remove any lint or debris around vac shoe. 6. Check spray jets for full spray pattern. 7. Remove lint and dirt build-up from brush and housing. NOTE: Brush removal. A. To remove brush, grab and pull brush out from end opposite drive belt (operator’s right). Remove other end from brush driver. B. To install brush, line up slots in brush core with pin in driver on drive belt side (operator’s left) and push brush onto driver. Then snap bearing end (opposite end) of brush into retaining clip. 8. Check cooling air screen (located on frame behind left wheel) for lint or debris. 9. Check float and shut-off screen and clean as necessary. NOTE: Always store machine with brush in “Store” position. 4-1ENG CADET 86038340 04/19/07 MAINTENANCE ONLY QUALIFIED MAINTENANCE PERSONNEL ARE TO PERFORM THE FOLLOWING REPAIRS. Vac Motor Carbon Brushes Replacement (Ametek) End Cap VACUUM MOTOR REPLACEMENT Carbon Brushes ! WARNING: 1. Turn off all switches and unplug machine. 2. Remove recovery tank. 3. Remove the (2) screws that fasten the solution tank to the frame, and tilt tank back to expose the inside of the frame. 4. Locate the vacuum motor wires and disconnect at the connector. Close the solution tank. 5. Remove the (6) screws holding the vacuum motor cover (p/n 86003080-PRV NO. 27809) to the solution tank. 6. Remove the vacuum motor. 7. Reverse process to install vacuum motor. Vacuum Motor Carbon Brushes Replacement (Windsor) End Cap Carbon Brushes WARNING: The green ground wire must be attached for safe operation. See wiring diagram. WARNING: The green ground wire must be attached for safe operation. See wiring diagram. Note: When replacing carbon vac motor brushes loosen wire terminal BEFORE removing screws on bracket. If armature commutator is not concentric, extremely pitted, or grooved the motor will need to be replaced or sent to a qualified service center to restore vac performance. Wire Terminal Wire Terminal Important: These brushes wear quicker as the length shortens due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely. If armature commutator is grooved, extremely pitted or not concentric, the motor will need to be replaced or sent to a qualified service center. Note: Place stop in groove. 3/8 Periodically check the length of the carbon brushes. Replace both carbon brushes when either is less than 3/8" long. Important: These brushes wear quicker as the length shortens due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely. 3 [9.5mm] 8 Periodically check the length of the carbon brushes. Replace both carbon brushes when either is less than 3/8" (9.5mm) long. CADET 86038340 04/19/07 4-2ENG MAINTENANCE BELT REPLACEMENT 1. Turn off all switches and unplug machine. 2. Remove recovery tank and brush. 3. Remove the (2) screws that fasten the solution tank to the frame, and tilt tank back to expose the inside of the frame. 6. Remove the (3) screws that fasten the side plate (p/n 86249420 – PRV NO. 62759) to the brush housing to remove belt. NOTE: All components associated with driving the brush will come out with the side plate. 7. Reverse process to install belt. 4. Loosen the (4) screws that hold the brush motor in place and slide motor forward to release tension in belt. 86249420 PRV NO. 62759 62759 5. Remove the (2) screws that fasten the vacuum shoe links (p/n 86227350 – PRV NO. 05016) to the brush housing. ! WARNING: 86227350 05016 PRV NO. 05016 ONLY QUALIFIED MAINTENANCE PERSONNEL ARE TO PERFORM THE FOLLOWING REPAIRS. SOLUTION PUMP REPLACEMENT 4. Remove solution hoses from fittings in pump. 1. Turn off all switches and unplug the machine. 5. Remove the (2) screws that fasten the pump to the frame. 2. Remove recovery tank. 6. Reverse process to install pump. 3. Remove the (2) screws that fasten the solution tank to the frame, and tilt tank back to expose the inside of the frame. Pump Replacement Parts for Shurflo 100 psi (86026400-PRV NO. 65254) Pump Head 86251040 PRV NO. 65187 Pressure Switch 86161980 PRV NO. 42-809332 Pump Hsng 86288790 PRV NO. 41387 Valve Asm 86258830 PRV NO. 84161 Pump Replacement Parts for Flojet 73 psi (86006110-PRV NO. 65189) Pump Repair Kit 86004600 – PRV NO. 47176 Hsng/Pump Repair Kit 86136040 – PRV NO. 47350 4-3ENG Diaphram 86235100 PRV NO. 29206 CADET 86038340 04/19/07 TROUBLESHOOTING CHART PROBLEM CAUSE SOLUTION 1. Is the cord plugged in. 1. Plug in cord. 2. Circuit breaker tripped in building. 2. Reset breaker 3. Faulty switch. 3. Call for service. 4. Faulty power cord or pigtail. 4. Call for service. Vacuum Motor Will Not 1. Vacuum circuit breaker tripped. 1. Reset breaker Run 2. Faulty main vacuum switch. 2. Call for service. 3. Loose wiring. 3. Call for service. 4. Faulty vac motor. 4. Call for service. Vacuum Motor Runs But 1. Debris lodged in vac shoe. 1. Remove debris from vac shoe. Suction Is Poor 2. Dome gasket defective or missing. 2. Replace as necessary. 3. Vacuum hose cracked or hose cuff loose. 3. Replace or repair as necessary. 4. Recovery tank full / float ball stuck in the up 4. Turn off vac motor. Drain and rinse No Power, Nothing Runs recovery tank. position. Poor Or No Water Flow 1. Main pump switch off. 1. Turn on. (Carpet Is Streaky) 2. Jets clogged or missing. 2. Clean using a vinegar /water solution or replace. 3. Solution filter clogged. 3. Drain solution tank and clean solution filter. Brush Does Not Spin 4. Faulty solenoid. 4. Call for service. 1. Brush switch off. 1. Turn on brush switch. 2. Brush circuit breaker tripped 2. Reset circuit breaker. 3. Brush belt broken. 3. Replace as necessary. 4. Faulty brush motor. 4. Call for service. CADET 86038340 04/19/07 4-4ENG WIRING DIAGRAM 86003650 PRV NO. 34362 86268750 PRV NO. 88567 86268750 PRV NO. 88567 86268900 PRV NO. 88655 86268750 PRV NO. 88567 86004480 PRV NO. 41353 86268900 PRV NO. 88655 4-5ENG CADET 86038340 04/19/07 86268350 PRV NO. 88270 86001240 PRV NO. 14020 86268750 PRV NO. 88567 NOTES CADET 86038340 04/19/07 4-6ENG FRAME ASSEMBLY 30 7 19 18 15 (SEE PG. 5-11) A 21 B 12 33 11 10 3 34 31 6 28 5 22 26 9 32 2 25 27 16 29 8 13 20 5-1 14 4 24 CADET 86038340 07/14/14 FRAME ASSEMBLY REF PART NO. PRV NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 86003620 86004340 86001660 86004480 86239610 86005370 86005640 86005810 86198530 86249430 86006020 86250130 86250140 86006580 86273980 86010630 86010660 86010650 86006550 86256190 86226050 86066230 86134490 86253090 86002370 86233140 86274760 86006530 86272160 86276610 86005710 OPEN 34341 39528 41236 41353 41354 53641 57030 57245 99809 62761 64099 66282 66288 70085 70066 OPEN 87013 87025 87018 70074 73197 OPEN 89279 03107 99667 73943 20035 20041 70271 70057 66052 70697 57105 1 1 2 1 1 1 2 3 2 1 1 6 2 2 2 2 2 2 2 1 2 1 10” 1 1 1 2 2 1 1 3 DESCRIPTION SERIAL NO. FROM NOTES: FRAME, CLP FAMILY HOSE ASM, 1.5 BLK VAC X 15.5 HUBCAP, 5/8" SHAFT HARNESS, MAIN, CDT HINGE, TANK TO FRAME MOTOR ASM, BRUSH CLP FAMILY NUT, 10-32 HEX NYLOCK NUT, 1/4-20 HEX NYLOCK SS FOAM TAPE, 1/8 THK X 3/4 1SDA PLATE, BRUSH MTR CLAMP PULLEY, 1.4 OD, 6GR, MICRO-V PLUG, HOLE, .375" BLK PLUG, 9/16 OD BLK NYLON SCR, 1/4-20 X 1/2 PPHMS SS SCR, 10-32 X 3/4 PPHMS WASHER, 1/4 ID X 5/8 OD SS WASHER, 1/4 LOCK EXT STAR SS WASHER, #10 X 9/16 OD SET SCR, 10-32 X 1/4 KCP STRAIN RELIEF, 90 DEGREE WHEEL, 9.75" X 1.5" AXLE, 5/8 X 17.06L HEAT SHRINK, 3/4 ID UL/CSA SEAL, FRAME/TANK CLAMP, 7/16 DIA NYLON UL CLAMP, 2.0" WORM GEAR SCR, ¼-20 X ½ HHCS PLTD SCR, ¼-20 X 1 PPHMS SS PIN, ROLL I/8” X 1.0”L SCR, ¼-20 X 1.25 PPHMS SS NUT, ¼-20 HEX W/ STD WASHER CADET 86038340 07/14/14 5-2 BRUSH ASSEMBLY 31 15 25 11 7 25 29 30 8 16 12 26 24 38 18 16 30 39 10 22 34 4 44 45 36 40 37 33 47 41 26 32 17 28 35 3 43 21 13 42 27 6 1 19 14 17 23 20 30 25 29 25 46 3 9 2 5 5-3 CADET 86038340 04/19/07 BRUSH ASSEMBLY REF PART NO. PRV NO. QTY DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 86003730 86227100 86000900 86001100 86001140 86001300 86001310 86003620 86004060 86004470 86004980 86093080 86005110 86005120 86005130 86005640 86005850 86249410 86249420 86005930 86250680 86006220 86006430 86006510 86006590 86006650 86006700 86275530 86010640 86010650 86136750 86230620 86251710 86003070 86003370 86278130 86272770 86272510 86008650 86342240 86006030 86003390 86001140 86227150 86228890 86028010 86004750 03110 04084 09019 11045 12514 140343 140351 34341 36192 41345 50998 51311 51312 51314 51317 57030 57271 62758 62759 62762 64098 66192 67411 70043 70088 70177 70232 70497 87016 87018 70675 12524 67467 27805 29157 70737 67094 66310 80604 64102 29208 12514 05158 09137 47383 47416 1 1 2 1 1 1 1 REF 2 1 1 1 1 2 1 4 2 1 1 2 1 1 1 2 6 7 2 2 4 6 4 1 1 1 1 1 1 2 2 1 1 1 1 1 2 1 REF AXLE, ROLLER ADAPTER, BRUSH BRG. BEARING, 1.125ODX.500IDX.375 BELT, 180J6 MICRO-V BRUSH, 15L X 3.38OD BRKT, BRUSH PULLEY BRKT, BRUSH HEIGHT FRAME, CLP FAMILY GUARD, THREAD HOUSING, BRUSH 15" LABEL, BRUSH HEIGHT LINKAGE, ASM, BRUSH HEIGHT LINKAGE ASM, ROLLER SUPPORT LINK, ROLLER, FRONT LEVER, HEIGHT ADJUSTMENT NUT, 10-32 HEX NYLOCK NUT, 3/8 DIA CAP, TYPE PUSH PLT PLATE, BRUSH HOUSING RH PLATE, BRUSH HOUSING LH PLATE, AXLE RETAINER PULLEY, 2.2 OD, 6GR, MICRO-V PIN, ROLL 1/4 X 1.25L ROLLER, 1.9 DIA X 10.5 LG SCR, 10-32 X 5/8 PFHMS SCR, 10-32 X 1/2 PPHMS SS DL SCR, 10-32 X 1/2 FHMS SS SCR, 10-32 X 3/8 FHMS SS SCR, #10-24 X 1/2 SHCS WASHER, #10 LOCK EXT STAR SS WASHER, #10 X 9/16 OD SCR, 1/4-20 X.5/8 THMS PLTD NP BRUSH, 15 L X 3.35 OD G2 RING, TOLERANCE 7/8 ID X 1/2 W CLIP, BEARING DRIVER, BRUSH SHLDR BOLT, 3/8 OD X 3/8 L SS NP RING, 1/2 EXT. SNAP PIN, CLEVIS 1/4 X 1/2 PLTD COTTER, 1/4" RING SPACER, .81 X 1.06 X .125 PULLEY ASM, BRUSH DRIVER ASM, BRUSH BRUSH ASM, 15 IN ADAPTER, BRUSH BRG. DIE CAST BEARING, R6 3/8 ID BRUSH BEARING ASM. KIT, BRNG/ADPTR EXTRCTR CADET 86038340 02/22/11 SERIAL NO. FROM NOTES: 1000090563 1000090563 1000090563 1000090563 1000090563 5-4 PUMP ASSEMBLY 14 3 20 8 13 4 10 16 9 2 16 21 23 18 1 12 19 15 17 20 11 7 25 26 28 C (SEE SOLUTION TANK) 26 5-5 24 27 CADET 86038340 04/19/07 6 5 PUMP ASSEMBLY REF PART NO. PRV NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 86002470 86002480 86003470 86003490 86004570 86241680 86241680 86026400 86250140 86250140 86273750 86003640 86008360 86010570 86010810 86010650 86010820 86005590 86005580 86003500 86006590 86267400 86282340 86279930 86281900 86253020 86282350 22072 22090 31072 31074 44067 44073 57030 65254 66288 70195 70011 34355 78419 84165 87191 87018 87192 56014 56012 31076 70088 OPEN 880278 39720 29277 39531 73963 39721 1 2 1 1 2 2 2 1 2 2 2 1 1 1 2 4 2 1 1 2 2 1 1 2 3 1 2 DESCRIPTION SERIAL NO. FROM NOTES: COUPLING, 1/4 ANCHOR W/1" HEX CONNECTOR, 1/8FPT X 1/4 TUBE QC ELBOW, SWIVEL, 1/4MPTX1/4TUBE ELBOW, SWIVEL,3/84MPTX3/8TUBE QC JET BODY, MINI PROMAX BODY JET, MINI PROMAX 9503 NUT, 10-32 HEX NYLOCK PUMP ASM, 230V 100 PSI W/CONN PLUG, 9/16 OD BLK NYLON SCR, 10-32 X 1.25 PPHMS SS SCR, 1/4-20 X 5/8 HHCS SS FITTING,1/4 TUBE,"Y", QC TEE, 3/8 MPT X 3/8 TUBE, QC VALVE ASM,SOLENOID CLP FAMILY WASHER, 1/4"IDX1.0OD. FLAT SS WASHER, #10 X 9/16 OD WASHER, 7/16 X 3/4 X .19RUBBER NIPPLE, 1/4 CLOSE NIPPLE, 1/4 FPT QD ELBOW, 1/4 MPT X 3/8 TUBE, QC SCR, 10-32 X 1/2 PPHMS SS WIRE, 22" GRN/18 76011 X 76011 HOSE, 3/8 OD X 1/4 ID URTHN X 22” DUCT, 1/2 ID SPLT FLX X 16” HOSE, 1/4 ID NYLON X 5" SCREEN, INTAKE HOSE, 3/8 ID NYL11 YLW X 17” CADET 86038340 04/19/07 5-6 PUMP ASSEMBLY PRIOR TO S/N 1000153482 14 3 20 8 13 4 10 16 9 2 16 21 23 18 1 12 19 15 20 11 17 7 25 26 28 C (SEE SOLUTION TANK) 26 5-7 24 27 CADET 86038340 04/19/07 6 5 PUMP ASSEMBLY PRIOR TO S/N 1000153482 REF PART NO. PRV NO. QTY DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 86002470 86002480 86003470 86003480 86004570 86004580 86004580 86251080 86250140 86006830 86273750 86003640 86008370 86010570 86010810 86010650 86010820 86005590 86005580 86003500 86006590 86267400 86281890 86004350 86281900 86253020 86004400 86003490 86008360 22072 22090 31072 31073 44067 44068 57030 65197 66288 70386 70011 34355 78420 84165 87191 87018 87192 56014 56012 31076 70088 OPEN 880278 39529 39530 39531 73963 39591 31074 78419 1 2 1 1 2 2 2 1 2 2 2 1 1 1 2 4 2 1 1 2 2 1 1 1 3 1 1 REF REF COUPLING, 1/4 ANCHOR W/1" HEX CONNECTOR, 1/8FPT X 1/4 TUBEQC ELBOW, SWIVEL, 1/4MPTX1/4TUBE ELBOW, SWIVEL,1/4MPTX3/8TUBEQC JET BODY, MINI PROMAX BODY JET, MINI PROMAX 9504 NUT, 10-32 HEX NYLOCK PUMP ASM, 230V 73 PSI PLUG, 9/16 OD BLK NYLON SCR, 10-32 X 1.0 PPHMS SCR, 1/4-20 X 5/8 HHCS SS FITTING,1/4 TUBE,"Y", QC TEE, 1/4 MPT X 3/8 TUBE, QC VALVE ASM,SOLENOID CLP FAMILY WASHER, 1/4"IDX1.0OD. FLAT SS WASHER, #10 X 9/16 OD WASHER, 7/16 X 3/4 X .19RUBBER NIPPLE, 1/4 CLOSE NIPPLE, 1/4 FPT QD ELBOW, 1/4 MPT X 3/8 TUBE, QC SCR, 10-32 X 1/2 PPHMS SS WIRE, 22" GRN/18 76011 X 76011 HOSE, 3/8 URETHANE X 29" HOSE, 3/8 NYLON X 6" HOSE, 1/4 ID NYLON X 5" SCREEN, INTAKE HOSE, 3/8 ID NYLON YLW X 29” ELBOW, SWIVEL 1/4 MPT X 1/4 TUBE TEE, 3/8 MPT X 3/8 TUBE QC CADET 86038340 04/19/07 SERIAL NO. FROM NOTES: 5-8 VACUUM SHOE ASSEMBLY 1 4 11 7 13 10 2 12 3 5 8 6 7 11 5-9 CADET 86038340 04/19/07 VACUUM SHOE ASSEMBLY REF PART NO. PRV NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 86227350 86234760 86005810 86006790 86006790 86006840 86008130 86010620 86010630 86010700 86003780 86008120 05016 27674 57245 70351 70360 70390 73958 85039 OPEN 87013 87074 35171 73955 4 1 4 2 4 4 8 1 4 8 1 2 DESCRIPTION SERIAL NO. FROM NOTES: ARM, VAC SHOE PARALLEL COVER, ACCESSORY PORT NUT, 1/4-20 HEX NYLOCK SS SCR, 10-32 X 3/8 HHTR W/STAR SCR, 1/4-20 X.75 PPHMS PHIL SCR, 1/4-20 X 1 FHCS PLTD SPACER, 3/8ODX.058WX.2814,CRS VAC SHOE, 15" WASHER, 1/4 ID X 5/8 OD SS WASHER, WAVE 3/8ID X3/4D X.125 GASKET, ACCESSORY PORT SPRING, EXT .38D X2.75L X.055W CADET 86038340 04/19/07 5-10 CONTROL PANEL ASSEMBLY 12 11 16 8 2 7 1 4 18 17 3 6 14 9 21 10 19 13 15 5 D ( SEE SOLUTION TANK) 5-11 CADET 86038340 03/31/14 20A, 20B 20C, 20D CONTROL PANEL ASSEMBLY REF PART NO. PRV NO. QTY DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20A 20B 20C 20D 21 86001240 86230110 86002020 86002010 86261000 86005670 86005760 86064400 86006950 86006710 86007120 86007140 86256180 86010800 86004480 86242270 86010750 86005700 86006830 86002610 86002600 86031550 86260960 86245040 14020 14312 14949 14942 23671 57040 57116 61348 70532 70235 72126 72130 73195 87189 41353 500019 87100 57104 70386 23683 23682 23681 23521 50279 1 1 1 2 1 2 2 1 9 2 1 2 1 9 REF 1 2 3 1 1 1 1 1 1 TERMINAL BLOCK, 115V (3-4-3) BREAKER, 7 AMP BREAKER, 4 AMP BOOT, 3/8 CIRCUIT BREAKER CORD ASM NUT, 1/2 NPT CONDUIT NUT, 6-32 W/STAR WASHER PLTD PANEL, CADET CONTROL SCR, 10-32 X 1/2 PPHMS BLK NP SCR, 6-32 X 1.0 PH BLK NYLON SWITCH, DPDT 3-POSITION ROCKER SWITCH, SPST 2-POSITION ROCKER STRAIN RELIEF, 1/2 NPT (.48ID) WASHER, 10 FLT STL BLK ZNPLT HARNESS, MAIN, CDTI LABEL, CONTROL PANEL, CDT WASHER, 3/8 ID INT.LOCK THIN NUT, 10-32 W/STAR WASHER PLTD SCR, 10-32 X 1.0 PPHMS CORD ASM, 230V BRITIAN CORD ASM, 230V EURO CORD ASM, 230V SWISS CORD ASM, 230V, AUST LABEL, GROUND SYMBOL CADET 86038340 03/31/14 SERIAL NO. FROM NOTES: 1000032157 5-12 SOLUTION TANK ASSEMBLY 6 29 3 18 32 30* 7 24 33 25 13 13A 13B 10 16* 23 D (SEE CONTROL PANEL) 17 7* (SEE FRAME) 15 12 18 A 21 22 20 11 8 9 19* 2 28* 27* 1 B 5* 26* 4 (SEE FRAME) 5-13 C (SEE PUMP) 18 14 CADET 86038340 04/19/07 SOLUTION TANK ASSEMBLY REF PART NO. PRV NO. QTY DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 86233140 86233150 86003080 86003090 86235500 86003790 86003920 86281880 86240090 86004340 86001590 86240980 86005420 20041 20042 27809 27810 31081 35175 35231 39526 39527 39528 40049 41348 53791 3 1 1 1 1 2 2 1 1 REF 1 1 1 CLAMP, 2.0" WORM GEAR CLAMP, 3/8 HOSE (D-SLOT) COVER, VAC MOTOR COVER, BELT ELBOW, 3/8 MPT X 3/8 TUBE, PLASTIC GASKET, TANK TO VAC COVER GASKET, VAC COVER (CLP FAMILY) HOSE,1/2 CLEAR X 12 HOSE, 1.5 BLK VAC X 3.0 HOSE ASM, 1.5 BLK VAC X 15.5 HOSEBARB, 3/8MPT X 1/2 NYLON HOUSING, VAC MOTOR VAC MOTOR ASM, CLP FAMILY 13A 86230760 140216 - BRUSH SET, 230V VAC AMETEK 13B 86135330 140688 - BRUSH SET, 230V VAC MTR WINDSOR 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 86006600 86006590 86032240 86259060 86010650 86007970 86010630 86006580 86002370 86233260 86272840 86256170 86003950 86003960 86003970 86275690 86003940 86026660 86002870 86232280 70114 70088 75257 85037 87018 73864 87013 70085 20035 20092 67147 73169 35236 35237 35238 70525 35235 75276 27417 500012 2 2 1 1 10 1 3 3 2 1 1 1 1 1 1 6 1 1 1 1 SCR, #10 X 3/4 PPHST TYPE B SCR, 10-32 X 1/2 PPHMS SS TANK, CDT SOLUTION VENT, COOLING AIR SMALL WASHER, #10 X 9/16 OD STRAINER, 3/8 IN. NPT 60 MESH WASHER, 1/4 ID X 5/8 OD SS SCR, 1/4-20 X 1/2 PPHMS SS DL CLAMP, 7/16 DIA NYLON UL CLAMP, 3.5" WORM GEAR RING, 2" DIA SPLIT STRAIN RELIEF, CORD HOOK GASKET, TANK, L-F GASKET, TANK, L-R GASKET, TANK, RH SCR, #10 X 1.0 PPHST TYPE B GASKET, CDT PANEL TANK ASM, SOLUTION CDT7 CORD, 99807 1/8 X 12" CARD, INSTRUCTION CDT7 CADET 86038340 04/19/07 SERIAL NO. FROM * NOTES: SERVICE ONLY SERVICE ONLY * ITEMS 5-14 RECOVERY TANK ASSEMBLY 16 15 5 E 18 7 11 4 12 8 10 E 1 14 9 12 13 17 2 6 11B 3 10B 1B 14B 12 5-15 CADET 86038340 04/19/07 RECOVERY TANK ASSEMBLY REF PART NO. PRV NO. QTY 1A 1B 2 3 4 5 6 7 8 9 10A 10B 11A 11B 12 13 14A 14B 15 16 17 18 86002400 86002350 86233140 86008400 86003110 86235280 86003630 86003910 86003930 86004200 86004510 86004450 86004500 86006240 86006600 86032250 86001370 86001190 86002870 86242230 86245940 86003330 20064 20002 20041 78499 27816 28060 34351 35230 35232 39353 41391 40019 41390 66227 70114 75258 140408 140133 27417 500009 50995 28061 1 1 1 1 2 1 1 1 2 1 1 1 1 1 6 1 1 1 1 1 1 1 DESCRIPTION CLAMP, 2.0" WORM GEAR X .312 CLAMP, 2.0” NYLON RATCHET CLAMP, 2.0" WORM GEAR TETHER, DRAIN PLUG COVER, REC. TANK (INSIDE) DOME, CLP FAMILY FLOAT SHUT-OFF GASKET, DOME GASKET, PORT COVER HOSE, 1.5 X 12.0 DRAIN HOSE, INSERT HOSEBARB, 1.5 DOUBLE MCHD HOSE, CAP PLUG, DRAIN HOSE SCR, #10 X 3/4 PPHST TYPE B TANK, CDT RECOVERY BRKT, HOSE HOOK BRKT, RECOVERY HOSE MTG CORD, 99807 1/8 X 12" LABEL, WARNING LABEL, CADET MAIN DOME ASM, CLP FAM CADET 86038340 12/20/12 SERIAL NO. FROM 1000083948 NOTES: 1000083948 1000083948 1000083948 5-16 SUGGESTED SPARE PARTS PART NO. PRV NO. DESCRIPTION 86001140 86001100 86000900 86004570 86241680 86026400 86010570 86003780 86230110 86002020 86007140 86007120 86005420 86007970 86230760 86135330 86003630 86003330 86006240 5-17 12514 11045 09019 44067 44073 65254 84165 35171 14312 14949 72130 72126 53791 73864 140216 140688 34351 28061 66227 BRUSH, 15L X 3.38OD BELT, 180J6 MICRO-V BEARING, 1.125ODX.500IDX.375 JET BODY, MINI PROMAX BODY JET, MINI PROMAX 9503 PUMP ASM, 230V 100PSI W/CONN VALVE ASM, SOLENOID CLP FAMILY GASKET, ACCESSORY PORT BREAKER, 250VAC 50 VDC BREAKER, VDE CIRCUIT SWITCH, SPST 2-POSITION ROCKER SWITCH, DPDT 3-POSITION ROCKER VAC MOTOR ASM, CLP FAMILY STRAINER, 3/8 IN. NPT 60 MESH BRUSH SET, 230V VAC AMETEK BRUSH SET, 230V VAC MTR WINDSOR FLOAT, SHUT-OFF DOME ASM, CLP FAM PLUG, DRAIN HOSE CADET 86038340 04/19/07 SERIAL NO. NOTES: FROM * 5-18 CADET 86038340 04/19/07