Transcript
The Experts in Small Printer Solutions
Ap1310-BTi Thermal Printer
Quick Start Guide Able Systems Limited Denton Drive, Northwich, Cheshire CW9 7TU England Tel: +44 (0) 1606 48621 Fax: +44 (0) 1606 44903 Web: www.able-systems.com
What’s in the box? ● ● ● ● ●
Bluetooth Printer (Ap1300BTi or Ap1310BTi) x1 Roll of 35mm or 55mm Diameter Thermal Paper x2 Universal Input Trickle Charger (UK/Euro/USA/AU-NZ) x1 Belt Mounting Kit x1 Quick Start Guide x1
Setting up Connecting the Battery Pack For safety, the Battery Pack is supplied discharged and disconnected. Before use, the Battery must be connected and fully charged. 1 Remove the screw from the Battery Compartment Door. 2 Push down, and slide back the Battery Compartment Door. 3 Fit the Battery Pack Connector taking care to insert it correctly. 4 Fit the Battery Pack ensuring wires are correctly routed and not trapped.
1
2 4 3
Connecting the AC Battery Charger Plug the AC Battery Charger into a suitable Mains Outlet Socket and Insert the Jack Plug into the Power Connector at the rear of the Printer. When connected by Bluetooth to another device, the blue LED light There is also the option of charging the Printer via the Jack Socket in the D9 Connector. Fully charging the Battery Pack takes about 15 hours. The printer should not be used during this time.
Loading Paper 1 2 3
Slide the Lid Release Button forwards until the Lid springs open. Unwind a small amount of paper from the roll and Insert the Paper Roll into the Printer. Close the Lid down, and the paper is loaded.
Pressing the paper feed button when the printer is idle advances paper at typically 50mm per second, depending on the battery voltage. However, the feed button has several additional functions: A single press and release of the button: ● In idle or spooling mode, advances paper. ● In sleep mode, wakes up the printer into idle mode. “Double-clicking” the button: ●
●
encoded calibration data, and the full character set. In spooling mode, exits spooling mode and prints any stored data.
1
3
2
Using your Bluetooth printer
Charging
The Ap1300 and Ap1310 are operationally identical.
LED Flashes Blue/Violet
LED patterns indicate the following modes:
Whilst connected to a trickle charger, the unit can both receive and print data. Leaving a trickle charger connected to the Ap13x0BTi will permit the unit’s battery pack to be charged when the unit is not printing.
● Constant GREEN: operating normally from battery pack. ● ● ORANGE: battery is being charged. ● RED: battery is low, or other problem. ●
A full charge takes 10-16 hours. When charged, the printer should be unplugged from the charger.
The LED patterns will change when connected to another device via Bluetooth. All GREEN will be replaced by BLUE. All ORANGE will be replaced by PURPLE.
Connecting to Mobile devices To connect to your iPod, iPhone or iPad device, follow these steps: Ensure the printer is awake 2 On your mobile device’s settings app, enable Bluetooth and connect to the printer marked “Able Ap13x0-BTi” 3 When prompted, enter the PIN “1234” 1
4 Your mobile device will now be connected to your
mini-printer and ready to print
Accessories ●
●
●
●
●
●
●
●
Universal Input Trickle Charger (UK/Euro/USA/AU-NZ). Product Code: BC1300V2 Cigarette Lighter Vehicle Battery Charger Product Code: BC1300CLAH 35mm Diameter Thermal Paper Roll (Approx. 13m long). Product Code: A05836TPR1 55mm Diameter Thermal Paper Roll (Approx. 34m long). Product Code: A05856TPR1 RS-232 D9 to RJ12 Data Cable. Product Code: AP1300-D9 Replacement / Spare Battery Pack . Product Code: Ap1300-BP01 Removable linerless label kit for Ap1300 models. 12 rolls /box; approx. 12.2 metres per roll Product Code: A05836RLRV2KIT Removable linerless label kit for Ap1310 models. 8 rolls /box; approx. 24.4 metres per roll Product Code: A05855RLRKIT
Tech Spec Product Colour TM Bluetooth Printer (35mm diam. roll) White Bluetooth PrinterTM (55mm diam. roll) White (All models include rechargeable battery pack) Print Mode: Interface Details: Bluetooth: Battery Pack: Charger: Print Speed: Thermal Paper: Printer Life:
Code Ap1300-BTi AP1310-BTi
Thermal Line Dot Print (8 dots/mm) RS-232 Rx, Tx, Busy, Ground, Wake-up control, Optional Trickle Charger Input.. Selectable baud rates and formats. (Default: 9600,N,8,1) Serial Data Cable available Full Bluetooth Support Bluetooth V2.1 (up to 10m range) 5 Cell NiMH Battery Pack (1.8Ah capacity) Ap1300-BP01 Universal Input Trickle Charger (UK/Euro/USA/AU-NZ) BC1300V2 Input: 100-240V 50-60Hz Auto Switching 50 mm/s. Typical with a fully charged battery Paper Width = 58mm Paper Width 108 print pulses or 50kms of Paper (more than 13 million print lines = 3500 Paper Rolls)
Printer Dimensions: eight (mm) Width (mm) epth (mm) Weight including Paper Roll and Battery Pack (g) Max Outer Diameter for Paper Roll (mm) Typical Paper Roll Length (m) Paper Roll Order Code
Ap1300BTi 47 92 108 345 35 13.5 A05836TPR1
Ap1310BTi 65 95 128 446 55 34 A05856TPR1
WARNING: Only use Able Systems approved Battery Packs and Chargers For a Full User Guide please visit our Website: www.able-systems.com To learn more about Able’s Print App, please visit www.able-systems.com/able-print-app.asp Document Reference: V1.0
Download the FREE app here! iPad®, iPhone® and iPod touch® are trademarks of Apple Inc. registered in the U.S. and other countries.
Made for: iPad (4th generation), iPad mini, iPad (3rd generation), iPad 2, iPhone 5, iPhone 4S, iPhone 4, iPhone 3GS, iPod touch (4th generation)
ally to iPod, sible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone, or
T H E
P O W E R
T O
P R I N T
Able Systems Limited Denton Drive, Northwich, Cheshire, CW9 7TU England T: +44 (0) 1606 48621 F: +44 (0) 1606 44903 www.able-systems.com
