80 With Beep

Transcript

UMN_00094001 User Manual With Controller Beep Box 2 TECHNO-MEDIA srl Via IV Novembre 92, 20021 Bollate (MB) tel. 0248672988 - [email protected] ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL Document Revision Revisione N° 1 2 3 4 5 6 7 Date Owner Notes 28/01/2014 20/05/2014 26/09/2014 23/04/2015 01/03/2016 02/03/2016 08/03/2017 T-Media T-Media T-Media T-Media T-Media T-Media T-Media New Release 2014 Added New prog. Mode Minor Changes Minor Changes Added BeepBox Ver 1 Added Dish Focus Tuning Added Conenction BeepBox FastOn UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 2 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL Indice Document Revision ............................................................................................................................................... 2 INTRODUCTION................................................................................................................................................... 4 Symbols in this manual ..................................................................................................................................... 4 Technical Specification ...................................................................................................................................... 5 System Components ......................................................................................................................................... 6 Warranty............................................................................................................................................................. 8 Installation ............................................................................................................................................................ 10 Safety Instruction for Installation ..................................................................................................................... 10 Dish Assembly ................................................................................................................................................. 11 Arm Focus Tuning ........................................................................................................................................... 12 Antenna Installation ......................................................................................................................................... 13 Passage of the cables ..................................................................................................................................... 14 At this point the antenna installation will proceed in the vehicle. Had it not been executed yet, be sure to fully sealed waterproof box or previously mounted cable guide. .................................................................. 16 Installation of the control Box Beep Box Version 1 ........................................................................................ 17 Installation of the BeepBox Version 2............................................................................................................. 18 Electrical Connections ..................................................................................................................................... 18 BeepBox with preassembled Wires................................................................................................................ 19 BeepBox with FastOn connectors .................................................................................................................. 20 How to connect the Set Tob Box .................................................................................................................... 21 USE of the System SAT-TV 40; 65; 80 with BEEP-BOX 2.............................................................................. 23 Description of the system ................................................................................................................................ 23 Switching ON ................................................................................................................................................... 25 Switching OFF ................................................................................................................................................. 25 Closing the Antenna ........................................................................................................................................ 25 Satellite Searching Process ............................................................................................................................ 27 Scan Process................................................................................................................................................... 27 Programming the Receiver type ......................................................................................................................... 28 How to program the Set Top Box type ........................................................................................................... 28 PROTECTION ..................................................................................................................................................... 29 Motor Protection .............................................................................................................................................. 29 HOW TO UPDATE THE RECEIVER CHANNELS ........................................................................................... 30 BEEP SIGNALING DETAILS ............................................................................................................................. 31 PROBLEM and SOLUTIONS ............................................................................................................................. 32 UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 3 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL INTRODUCTION Symbols in this manual Read the Manual. Respect indication to avoid risks for user. Only qualified person of TECHNO-MEDIA srl. Pay attention. Correct. Wrong. UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 4 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL Technical Specification Dish Search Mode Power Supply Offset Dish with three dimension: 40, 65, 80cm Automatic, Satellite is recognized through the audio signal provided by your set top box Min Typ 12V Current Sink possible Max 14.5 Min Typ Max 80mA 150mA 1A Weight 4.3 Kg Protection Fuse 2A self restoring, one on the main 12V line and the secondo ne on the ignition line. Both inside the Beep Box. Dimension with dish closed Height 21cm Width 60 UMN_00094001 Depth 80 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 5 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL System Components Inside the box you will find: Automatic Antenna SAT-TV 40 or 65 or 80 based on what you purchased. 5 Meters Ethernet cable to connect the Antenna and The Beep Box. SCART-SCART Cable with an extra audio RCA out to be connected to the Beep Box. Coaxial cable to connect the antenna to the Set Top Box. UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 6 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL Depending on the version you purchased, you can have different type of power supply box. 1) The Beep-Box 1. This unit allow to power up the antenna and close it using the only one button available on the box. The same button allow to program the type of Set Top Box used and the satellite to be searched. Please refer to the paragraph: HOW TO PROGRAM THE SET TOP BOX TYPE 2) Beep-Box 2 This one allow to switch off the antenna in order to easily download the new settings for your Set Top Box. UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 7 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL Warranty Both Electronics and Mechanical parts are covered for 2 years. ** ** European Warranty. Keep copy of the purchase document ( without this document we could not proceed with a warranty repair). Cost of the parts and works are covered by the warranty. Shipment and risk for the transportation are customer costs. Under a valid warranty we will proceed to renew the system with the latest modification. The replaced parts will not be returned. The antenna warranty will be extended for an additional three (3) months and only on the same defect. If the validity of the warranty and in need of repair, bring the antenna to one of our authorized service center. If there is no service center in your area, please send the antenna in its original packaging at TECHNO-MEDIA srl. with a detailed explanation of the defect. For added traceability, it is required to send an email to: [email protected] UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 8 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL Exclusions and termination of the warranty Are expressly excluded from the warranty all those faults that are attributable (at the discretion of the TECHNO-MEDIA Ltd.) to: • Improper installation, misuse, neglect. • Tampering or antenna opened by the user or unauthorized personnel. • Failures that are attributable to an incorrect antenna use. • Use of non-original parts. • Failures caused by adverse weather conditions such as lightning, hail and strong wind. • Failures caused by supply voltage or incorrect connections. UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 9 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL Installation Safety Instruction for Installation It is needed to pay attention to the following guidelines in order to avoid damage to the people who will operate the installation. Since the antenna will (in most cases) mounted on the roof of the vehicle and this being an operation at risk of falling for the operator, you will need to take all preventive measures to avoid harm to people involved in the assembly. It must also check that the capacity of the vehicle roof is able to support the weight of the trader and tools needed during installation. Be sure that: 1. Antenna and its parts are not powered during installation. 2. People involved does not suffer from Vertigo. 3. There is no risk to fall down from the roof or from the aids used to reach it. 4. Do not stand in a risky position where tools or material can fall down during the installation. UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 10 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL Dish Assembly Dish is separated by the main body during shipment. To install it a single Phillis screw driver is needed. Screws are screwed on the main body and must be removed before installation. Place the main body on a stable and flat surface Align the 4 holes on the Dish with the four holes on the two support on the main body Align the 2 plates with the dish and the main body Set the four screw firmly UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 11 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL Arm Focus Tuning In case of problems pointing a satellite, it is possible that a tuning of the arm/dish angle is needed. In case of that: • • • • Switch on the Set Top Box Switch On the Antenna pressing the ON button Wait until the antenna start the horizontal rotation. Press the OFF button With a screwdriver , turn the screw shown in the picture in order to set the distance between the edge of the dish and the arm to 67 cm for the dish of 65cm and 86 cm for the one of 80cm Measure the distance from the hole close to the edge of the dish To the junction between the arm and the plastic of the LNB handler. Now switch ON again the Antenna and wait for the complete process. UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 12 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL Antenna Installation Verify that there is enough space on the roof of the vehicle in order to allow the antenna movement. The antenna always opens first vertically and then horizontally to allow you to reduce the overall operating conditions but, in far south regions, such as Morocco or North Africa, to point the antenna of some satellites could tip very back, so it is necessary that there are no objects that prevent its rotation. Consider a space of about 130 cm in diameter around the antenna as shown. Thoroughly clean the area identified for fitting and removing all traces of grease, dust and debris. With a caulking gun, apply a uniform layer of polyurethane adhesive on the baseplate of the antenna body (Area 1). Refer to the operating instructions of the adhesive used. Use adhesives compatible with the counter material (ABS) and the roof of your vehicle. Then position the antenna in the above cleaned area by paying attention to the direction. The arrow in the figure indicates the direction of march of the vehicle. Be sure that the antenna is parallel to the sides of the vehicle. UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 13 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL Press firmly on all four corners of the aluminum plate and at the center of the cap as indicated by the figure. Do not press above the parabola to prevent warping it. This will irreparably damage the mechanics. Select a suitable adhesive to fix the baseplate ABS to your roof. Follow the instructions from the manufacturer of the glue and in any case, let it rest at the appropriate temperature (see manual glue instructions) for at least 24 hours before starting move the vehicle. Passage of the cables If it was not already, make a hole for the passage of the two cables required to the antenna operation. After making the hole, fit the weatherproof box or the cable guide. Run the two cables supplied in the kit if necessary with the help of an electrician's probe, if you were to encounter resistance, DO NOT pull on the cables, you might run into the cable break and then the antenna malfunction. Such failure is not covered by warranty. Ethernet cable 5 meters NOT cross UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 14 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL Antenna Coaxial cable 5 meters Leave a sufficient cable length between the cable guide and the antenna so you can reach the connectors on the antenna connection body without bending too close or keeping in tension cables. If not already assembled, install the seal and plastic cap on the end of the Ethernet cable which is then connected to the antenna: First plug the Ethernet cable into the side of the guard as shown in the figure, first the rear and then plug in the casing front. Once the cable is into the two parts, open the rubber gasket provided and let it fit around the ethernet cable. Connect the RJ45 connector of the Ethernet cable to the antenna connector, as shown in the figure, insert the connector until the retaining tab does not Click UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 15 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL Move the seal close to the connector Screw the connector body as shown in the figure. Perform the operation carefully avoiding to turn the other party on the dome. Do this by hand without the use of tools, it is not necessary to tighten too hard. Screw the last part on the body of the connector so that the gasket is contained inside avoiding infiltrations of water. Do this by hand without the aid of tools, it is not necessary to tighten too hard Proceed at this point to the antenna cable connection. Be careful not to rotate the antenna connector on the body. At this point the antenna installation will proceed in the vehicle. Had it not been executed yet, be sure to fully sealed waterproof box or previously mounted cable guide. UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 16 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL Installation of the control Box Beep Box Version 1 The installation of BeepBox 1 is very simple, there are only three wires that must be connected: • Power (Red and Black Wires) • Ignition KEY power (Yellow Wire) • Audio Signal from Set Top Box Cavo Antenna Cavo Ethernet. Beeper e Fusibile Alim. Principale Chiusura Sotto Chiave 1. Connect the RED WIRE to +12V of the Battery 2. Connect the BLACK WIRE to the negative of the battery or to the vehicle chassy 3. Connect the YELLOW WIRE to a 12V line which is powered only when ignition key is turned or the vehicle is ON. 4. Keep the BeepBox in an accessible position. UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 17 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL Installation of the BeepBox Version 2 The control and power supply box supplies power to the antenna when you press the ON button or when the vehicle is set in motion. It allows you to close the antenna and to program the type of decoder used. Switching ON is delayed either pressing the ON button or turning on the vehicle. Install the Beep-Box leaving adequate ventilation to prevent electronics failures. Electrical Connections After identifying the position and set the controller to the wall, proceed to connecting all the wires of the same as shown below: Plug the RJ45 connector from the antenna on the roof of the vehicle in its connector, as shown in figure until you hear the click of the retention clips. Take the SCART-SCART cable ** from the package and connect the RCA connector to its connector on the controller. Refer to the figure on the side UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 18 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL At this point you can proceed to the connection of the power cables. Even if the voltages involved are quite low, pay attention to avoid shorts and invert connections. BeepBox with preassembled Wires 1. Connect the BLACK WIRE to the negative of the battery or to the vehicle chassy 2. Connect the RED WIRE to +12V of the Battery. 3. Connect the YELLOW WIRE to a 12V line which is powered only when ignition key is turned or the vehicle is ON. Refer to the below picture UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 19 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL BeepBox with FastOn connectors In case of BeepBox with FastOn connection, as shown in the following picture, proceed to connect power as indicated below: 1. Connect the BLACK WIRE coming from the negative of the battery to the Left FastOn 2. Connect the RED WIRE coming from +12V of the Battery to the center FastOn 3. Connect the YELLOW WIRE which came from a 12V line which is powered only when ignition key is turned or the vehicle is ON to the Right FastOn. UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 20 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL How to connect the Set Tob Box Connect the coaxial cable coming from the roof at the RF IN of your decoder. (Refer to the manual for your decoder to verify which input to use). Connect the SCART-SCART cable to the decoder in the output for the normal connection of the TV. Use the side of the cable from which also comes the wire that is currently connected to the Beep-Box (See wiring). If your TV is equipped with SCART input connect the other end [2] of the cable and keep the RCA [1] connector connected to the Beep-Box. If your decoder and your TV support it connected the HDMI cable. UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 21 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL All the connections have been made. You can power up the set top box. Connect the power cord to the Set Top Box [2] and if the system has one, turn on the switch [1] UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 22 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL USE of the System SAT-TV 40; 65; 80 with BEEP-BOX 2 Description of the system Every system, use an automatic process to point the satellite which does not require intervention by the user. The system allow to point a satellite independently by the type or model of the Set Top Box used and independently by the orientation and/or the inclination of the vehicle. Some receiver like the pay per view ones, require longer time to lock the satellite signal, in this case you need to change the type of the set top box using the programming approach mentioned in the related paragraph. This type of receivers will make the scanning process longer. Remember that the Antenna can point the satellite ONLY if the Set Top Box has at least one channel (of the pointed satellite) pre-programmed on it. System is designed to work with any Set Top Box. Anyway there are Set Top Boxes like SKY and/or PAY PER USE which require longer time to lock the signal. For this reason, if your receiver is one of those, you need to program the system to work with it selecting the SKY and/or PAY PER USE mode. To Select the SKY and/or PAY PER USE please refer to the paragraph “Programming the Receiver Type”. The GPS allow to point the satellite with the maximum accuracy. The Tilt Sensor (if installed) will correct any possible vehicle inclination. The pointing procedure is started as soon as the set top box is powered up and the power is applied to the LNB. The time needed to start the process may change based on the Set Top Box type. UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 23 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL Some Receiver, even if in Stand-By does not remove the power to the LNB and this does not allow to close automatically the antenna. This behavior is typical of Set Top Boxes like SKY and/or PAY PER USE. In this case you have to switch off the receiver using the power switch or disconnecting the power cable. UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 24 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL Switching ON To power on the antenna press the ON button on the Beep-Box. Switching OFF To power on the antenna press the OFF button on the Beep-Box. Closing the Antenna Antenna can be closed in three different ways: 1. Switching off the receiver • If your receiver remove the LNB power when switched off, then to close the antenna it is enough to put the Set Top Box in Stand By. In case the Antenna is already pointed to the desired satellite, to close it, you need to press the Close Button. 2. Pressing the close button on the BeepBox version 2 or the only one button available on the BeepBox version 1. If as indicated in the paragraph "Description of the System" your set top box does not allow to remove the LNB power, than to close the antenna it is enough to press the CLOSE button. After the antenna close down, an infinite series of beep is played until the receiver power is not removed or the OFF button is pressed. UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 25 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL 3. Switching ON the Vehicle • For safety reasons, when the vehicle is switched on or the Ignition KEY is turned, the antenna will close automatically (yellow cable MUST be connected). A continuous beep will be sound until the antenna is in movement, does not move the vehicle until the beep is present. UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 26 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL Satellite Searching Process The search of the pre-selected satellite is started as soon as the receiver is powered up and the Antenna is powered up pressing the ON button. • When the receiver is powered UP a new searching process is started. Scan Process Here the different Scan steps: 1. The antenna move to the Zero position. 2. The antenna set the required inclination to pint the desired satellite using the position provided by the GPS or the default elevation if the GPS does not have the fix. 3. A complete rotation is performed. 4. Antenna move immediately back to the highest power satellite found. 5. A tuning process is started. a) If a valid audio signal is revealed the Antenna stop in this position and will be possible to close it only pressing the CLOSE button or switching on the vehicle. b) If the audio signal is not revealed, the system move to the next satellite. If at the end of the loop no satellites are found, the scan is performed again with different settings. If at the end of all scanning processes the satellite is not found, the antenna will close down. UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 27 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL Programming the Receiver type How to program the Set Top Box type To enter the programming mode: • Switch off the vehicle and leave the vehicle key in the off position • Switch off the Receiver • Switch off the Beep Box If you enter the programming mode and you want to exit it, just leave it run and don’t touch any button. Remember that in this case the default decoder type is moved back to the standard type which is not the correct setting for the receivers which needs longer locking times. 1. Switch on the BeepBox and wait for the switching on beep sequence 2. Press quickly and continuously the CLOSE button until you hear a long beep. 3. If your receiver IS NOT a ‘’ SKY and/or PAY PER USE’’ a. Wait 1 beep b. Press and keep pressed the CLOSE button. Then a long quick sequence of beeps is played. This is confirming that the new setting has been saved. 4. If your receiver IS a ‘’ SKY and/or PAY PER USE’’ a. Wait 2 beep b. Press and keep pressed the CLOSE button. Then a long quick sequence of beeps is played. This is confirming that the new setting has been saved. UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 28 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL PROTECTION Motor Protection If an obstacle is within the movement range of the antenna blocking the turning or rising movement, the system will notice the user playing 2 sequences of three beeps and stopping the movements. To restart the system, remove the obstacle and press the CLOSE. For more information on the Beep signaling please refer to ‘Beep Signaling Details’’ Take all necessary precautions if you must get on the vehicle roof. Avoid using metal rods for the removal of obstacles when weather conditions are adverse. UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 29 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL HOW TO UPDATE THE RECEIVER CHANNELS As explained in the previous chapters, SAT-TV-40-65-80 is able to lock the satellite only if the receiver used was previously programmed with the channels and the satellite which the user would use. Anyway, it is possible to update the receiver channels after the antenna is pointed. Follow these points in order to update your receiver: 1. Start a new search process setting your Set Top Box on a free channel (not encrypted). 2. Wait that the antenna lock the satellite. 3. Press OFF button on the BeepBox version 2 BEEP-BOX. During the Set Top Box update process, do not operate any button on the Beep Box, do not switch on the antenna and do not turn on the Ignition Key 4. To start the update process refer to the Set Top Box user manual.. 5. Switch on the Antenna only at the end of the Set Top Box update process. UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 30 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL BEEP SIGNALING DETAILS The model SAT-TV-40-65-80 and the BeepBox use different sequences of beeps to provide signaling of different status and condition. Below the different conditions: Signaling at Power ON 1 Beep 2 Beep 3 Beep 4 Beep Signaling during SCAN 1 Beep and Antenna moving back to the starting position 5 fast Beep 10 very fast beep ALARM 2 sequences of 3 Beep Description Loading memory position, GPS not locked GPS locked and memory position loaded Not saved position available, Scan Running with GPS not Locked Not saved position available, Scan Running with GPS Locked. Description GPS locked dusring scan, the system start aew scan using the GPS data Tuning performed Satellite locked Description Antenna in protection mode due to an obstacle which does not allow the system to move properly. Remove the obstacle and press CLOSE to reset. UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 31 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL PROBLEM and SOLUTIONS In case the antenna can not lock the satellite properly: The Antenna point correctly the satellite, beepbox sound the 5 fast beeps after fine tuning, image and audio are available on the TV but the antenna move to the next satellite. Double check the SCART-SCART-RCA connection between Set top box and Beppbox. See the connection example in the manual. Switching on the Set Top Box the Some receiver require more than 30 seconds antenna does not start the search to power up the LNB. If after this time the process. antenna does not start the serach process double check if the coaxial cable is properly connected to the right input of the Set Top Box. If the problem does not disappear, probably the coaxial cable was broken during the installation. Check the paragraph related to the installation process Antenna perform the search process, Double Check the connection between STB stop on the satellite but the channel is and TV. not visible on the TV Double check if the channel on the STB is properly programmed Sometime the STB get blocked and needs to be switched off and on. UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 32 ‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL UMN_00094001 Vi ringraziamo per il vostro acquisto UMN_00094001 Rev 7 TECHNO-MEDIA SRL Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected] 33