Transcript
客 戶 承 認 書 SAMPLE SPECIFICATION AND APPROVAL SHEET 承認書編號(REPORT NO)
201106004
客 戶(CUSTOMER)
強復工業有限公司
品 名(PART NAME) 型 號(TYPE NO)
JD-8025S1L3-2
規 格(SPECIFICATION)
1400±10%RPM
客 戶 料 號(PART NAME) 送承認數量(QUANTITY )
3PCS
送承認日期(DATE) 洪正雄
業務經辦人(PREPARED BY) 本公司承認章 SIGN FOR "ANODE" APPROVAL
收樣客戶承認章 SIGN FOR CUSTOMER APPROVAL
*本公司保證銷售之產品均符合本承認書之規格,如有變更加則先行送請承認後始得變更. WE GUARANTEE ALL PRODUCTS SOLD ARE UNDER"SAMPLE SPECIFICATION AND APPROVAL SHEET",THERE IS NO CHANGE WILL BE MADE EXCEPT BEEN APPROVED.
*感謝您給予敝公司送樣承認之機會,如惠蒙通過承認,煩請將此表傳真回敝公司以利歸檔. WE APPRECIATE FOR THE OPPORTUNITY OF SAMPLES APPROVAL,PLEASE FAX THIS TABLE BACK TO US FOR FILING AFTER AUTHENTICATED. 正極科技有限公司 Anode Technology Co.,LTD 地址:台北縣中和市中正路683號17樓之3 TEL：+886-2-2226-8801
FAX：+886-2-2226-8802
廣東省東莞市茶山鎮京山工業區 TEL：0769-86862136
FAX：0769-86862139
经理室 MGR
业务部 SALES
工程部 R ﹠D
洪正雄
陳震
规 格 SPECIFICATIONS 1． 电源线长度及端子 Lead wire length and connector 1-1．标准规格 Standard specifications:2510-3P 黑红黄 UL1007 26# 框外 450mm 转 2.0 正端 UL1007 26# 总长 50MM.
2．机构 Mechanical 2-1.．外观尺寸Ｅxternal dimension
80*80*25
2-2．重量 Weight
58.25g
2-3．轴承 Bearing
Sleeve
bearing
3．电气特性 Electrical characteristics(在通风及额定电压条件下 in free vair at rated voltage) 3-1．额定电压 Rated voltage
DC12V
3-2．额定电流 Rated current
0.08±10%A
3-3．额定输入功率-Rated input power
0.96W
3-4．操作电压 Operating voltage range
6-13.8V
3-5．起动电压 Starting voltage
6V
3-6．锁定电流 Locked current
0.10±10%A
3-7．特性定义 Characteristics definition 3-7-1．额定电流（3-2）&额定转速（4-1）&额定操作功率（3-3），须在额定电压下（3-1），在常 温 25℃，湿度 15～65%RH 马达连续运转 5 分钟达到规格下限，10 分钟达到正常值 Rated current rated speed,and rated input power temperature 40℃ ＆ humidity 15～ 65%RH shall reach bottom line of specification after 5 minutes continuous rotation at rated voltage and reach standard specification after 10 minutes continuous at rated voltage. 3-7-2．启动电压是指当突然通电后能够使风扇启动之最低电压 Staring voitage is the least voltage that enables to start the fan by sudden power on.
4．效率 Efficiency 4-1．风扇转数 Rated speed (范围 range)
1400±10%RPM
4-2．最大风量 Maximum air flow
16.9CFM
4-3．最大静压 Maximum static air pressure
0.81mm-H2O
规 格 Specifications 5.特性规格 Characteristics 5-1.操作温度 Operating temperature 5-2.储存温度 Storage temperature 5-3.环境湿度测试 Environment humidity 5-4.绝缘阻抗强度 Insulation resistance
5-5.绝缘耐压强度 Dielectric strength
-10℃～+70℃ -30℃～+85℃ 10﹪℃(RH)45℃ for 24 hours＆98﹪(RH)45℃ for 24 hours
在本体与两条导线间加 500V 直流电压之绝缘阻 抗在 100MΩ以上。 At least 100MΩ at 500 VDC between housing and both lead wires 必须能抵抗在本体与两线间加 500V 交流电压 1 分钟。 Withstand 500 VAC 1 minute 1 mA between housing and
both lead wires 5-6.预期寿命（MTBF）：指在额定电压及正常温度，湿度条件下连续运转。 Life expectance:continuous operation at rated voltage and normal temperature ＆ humidity. 5-6-1.含油轴承预期寿命：至少 20，000 小时。 Slecve bearing life expectance:20,000 hours minimum. 5-6-2.一个含油轴承和一个滚珠轴承预期寿命：至少 30，000 小时。 One slecve and one ball bearing life expectance:30,000 hours minimum. 5-6-3.双滚珠轴承预期寿命：至少 40，000 小时。 Two ball bearing life expectance:40,000 hours minimum. 5-7.端子抗拉强度 端子以 1 公斤的拉力拉扯 15 秒不会脱落。 Tensile strength of connector Connector will not be any broken at 1 kg for 15 secon 5-8.噪音分贝 Acoustic sound level 17.22Dba (Max) 5-8.噪音测试说明 Acoustic sound level test descriptions. 以额定电压在噪音实验中测试背景噪音 14.9 分贝 At rated voltang in sound proof room Background noise:14.9Dba 悬吊 Suspension
1m 通风状态 Free air
麦克风感应器 MIC. sensor
（对准风扇中心） （Aim to center of the fan）
风扇 Fan
规 格 Specifications 6.保护功能 Protection 6-1.风扇旋转锁定测试：将风扇通电锁死测试至少 0.1 小时，当锁定解除之后仍然正常运转。 Lock test:Locked any fans for at least 0.1 hours.Fans work in normally after locked released.
CE 7.安全规格 Safety
8.原材料 Material 项次 Item 8-1 8-2 8-3 8-4 8-5
8-6 8-7
8-8
8-9
8-10 8-11
主要元件 Major components 外框 Fan housing 扇叶 Fan blade 轴心 Stator core 轴承 Bearing 橡胶磁铁 Rubber magnet
材质或型号 Material&Specification PBT PBT 不锈钢 Sus420j2 含油轴承 Sleeve bearing 铁锶粉末化合物 Strontium ferrite (BQB14W) H50
矽钢片 Silicon steel strip 漆包线 MW-2 UEW Enameled copper wires 印刷线路板 单层印刷线路板 PrintedCircuitBoard Wiring printed single layer board 电源线 Lead wires 聚乙烯氯化物包铜线 Polyvinyl Chloride enameled copper wires(AWG) 贴纸 Label JD8025S1L3 端子接头 Connector housing
2510-3P-2.0-2P
等级 Grade
UL 号码 UL NO.
备注 Rrmark
规 格 Specifications 9．注意事项 （Nores） 9-1． 使用时请勿超出本规定所规定之极限，否则我们不保证此产品 We,Fu Fang will nor guarantee the products if the application of our products are exceeded the limitation which isspecified on the specification 9-2． 倘若要变更此份文件任何规格，请务必事先提出要求 ln case of changes of the specification specified on thid document A WRITTEN NOTICEIS REQUESTED INADVANCE 9-3． 请勿触压着叶片以电源线缠绕着风扇或用力拉扯电源线，如此轴心与电源线将会被损坏 please do not touch the impeller with the pressure and never bring the fan with lead wire The bearing and lead wirenay be damaged 9-4． 本产品不保证因粉尘、水滴、小虫进入，而影响寿命与不良产生 No guarantee on the products against the safety problem or failure caused by powder dust,drop of water or insect 9-5． 如有任何资料及文件与此份资料不同，将以此份资料为主要参考 lf there is any data or related documentation different from this data sheet.This data sheet is the inciple reference 9-6． 请勿在可燃性气体与任何有害环境中使用 please do not use the fan in the environment of corrosive gas or liquid or any detrimental gas 9-7．请于六个月内使用，否则风扇存放在很高温或很低温及湿度很高的室温中，风扇于六个月后 将可能会有漏电流产生 piease do not store the fan in the environment of high/low temperarure,high humidity or detrimental gas.PIeasestore within six months,every six months,shall be a leakage of electric current to the fan,，even though the fan isstored in room temperature 9-8． 当风扇于运转转中，请勿企图将风扇锁死特别长的时间，如此，会因连续停止不转，产生 高热而烧毁风扇 while the fan is in operarion,please do not lock the fan intentionally for a long period of time,since the continuousstoppage will result in overheat and thus burnt out the fan.. 9-9． 组装风扇时，请特别注意，因共振或振动产生的噪音 During the installation of the fan，please pay sudstantial attention to possible notice caused by resonance vibrationand shock 9-10．当搬运或作业中，风扇如从 60cm 的高底落下，将会对叶片的平衡产生若干影响，特别是 滚珠轴承避免掉落 lt is very important to notify that avoid to drop fron 60cm height when in any movement or operation,it will impactthe balance ofblade.Especially ball bearing structure is avoided to drop down 9-11．锁外壳之螺丝扭力不得超 4.6 kg -5.3 kg The torque of the screw that locked the frame should not exceed 4.6kg-5.3kg
F
E
D
B
A
C
AIR FLOW
ROTATION 80± 0. 5
25. 0± 0. 5
71. 5± 0. 3
71. 5± 0. 3
80± 0. 5
8- ?4. 5± 0. 3
4. 15± 0. 15
4. 15± 0. 15
2510
2
2
2510- 3P黑红黄 1007 26AWG框外450mm转2. 0正端1007 26AWG总长50mm
F
E
D
C
B
A
1
1
正极科技有限公司
