Transcript
Product: 8202 Manual Dimension: 8.5"x 11"/page Date: 2008/01/03
Color:
8202
UNIVERSAL WELDING CART
Black
8202
372 Old US Highway 52 South Mount Airy, NC 27030
UNIVERSAL WELDING CART
Call 1.800.221.9705 for questions concerning performance of the product or other inquiries.
www.astrotools.com
1 YEAR LIMITED WARRANTY
•Astro Pneumatic Tool Co. warrants our products to the original user against defective material or workmanship for a period of 1 year from the date of 1st use. Astro reserves the right to determine whether the product failed because of defective material, workmanship or other causes and to charge back for missing parts. Astro Pneumatic Tool Co., at its discretion, will repair products covered under this warranty free of charge. The original user is to return the product (with the exceptions listed below) with the distributor’s name, address, adequate proof of date of purchase or a copy of warranty card, and a short note explaining the problem. Failures caused by accident, alteration, or misuse are not covered by this warranty. •If one part of this product fails, please do not return the entire product. Astro will replace free of charge component parts of this product that fail within 1 year of first use by the original user. Items included in this category include but are not limited to kits, hand tool kits and any other product where there are multiple items or components that make up the unit. Please contact the phone number below in order to obtain the replacement components covered under warranty. •Astro Pneumatic Tool Co. or its authorized service representatives must perform all warranty repairs. Any repair to the product by unauthorized service representatives voids this warranty. The rights under this warranty are limited to the original user and may not be transferred to subsequent owners. •This warranty is in lieu of all other warranties, expressed or implied, including warranties of merchantability and fitness for a particular purpose. Some states do not allow the exclusion of limitations of incidental or consequential damages so the above limitations may not apply to you. All claims must be sent to:
Product Information • Heavy duty steel construction • Heavy duty wheels - two 7.5" solid wheel and two 3" Swivel • 3 shelves for easy access to supplies • Cart size: 27-1/2"(L) x 16-1/3"(W) x 28"(H) • Top shelf size: 17-3/4"(L) x 11-1/2"(W) • Bottom shelf size: 27-1/2"(L) x 11-1/2" (W) • Weight Capacity: 176lbs. Approximately
Astro Pneumatic Tool Company 372 Old US Highway 52 South Mt. Airy, NC 27030 PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING 1-800-221-9705 FOR INSTRUCTIONS
Unpacking
ASSEMBLY INSTRUCTIONS 1) Slide axle through support tube on bottom of shelf (03). Slip washers over both ends of the axle, fit wheels onto axle, insert cotter pins and finish by adding plastic caps on ends of axle.
When unpacking, check the parts diagram and part number listing on page 2 to make sure all parts are included. If any parts are missing or damaged, please call your distributor.
2) Install casters to the front of shelf using 4 hex head screws and washers to one side of shelf and 4 lock washers and hex nuts to other side of the shelf. Hand tighten all screws and nuts. 3) Fasten vertical support (04) to bottom shelf. 4) Fasten side support rail (05) to the bottom shelf. Please note that support rail (05) is shorter than (06) and should be attached to the side of the cart that has the flange of the top shelf bent downward (see breakdown image). 5) Add center shelf (02) with flanges up. Start by fastening center hole towards rear of shelf, then side holes in rear of shelf, finally front side holes to side support rails. 6) Fasten top shelf (01) in similar fashion, but include brackets (07) for cord storage to top front holes in side support rails. 7) Fasten side support rail (06) in the same manner as (05). 8) Tighten all fasteners
Important
Page 1
UNIVERSAL WELDING CART
8202-01 8202-02 8202-03 8202-04 8202-05 8202-06 8202-07 8202-08 8202-09 8202-10 8202-11 8202-12 8202-13 8202-14
Shelf A Shelf B Shelf C Shelf D Support Bar A Support Bar B Hook Screw Chain Axle Washer Pin Solid Wheel Swivel Caster
Page 2
1 1 1 1 1 1 2 40 2 1 2 2 2 2
