Transcript
88 4528 95 Wood Top Kitchen Cart (Black Finish) IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the wood parts. We have taken great care in the design of this product and request that you carefully and strictly follow our assembly instructions to ensure a completed product as it was designed.
PART LIST A. Top 1 pc.
B. Side Panel 1 pc.
D. E. Side Panel Back Stretcher 1 pc. 2 pcs.
I. Front Piece 1 pc. H. Back Panel 4 pcs.
C. Middle Panel 1 pc.
K. Divider 1 pc.
G. Back Piece 2 pcs. L. Base 1 pc.
J. Front Piece 1 pc.
M. Side Bar 2 pcs.
F. Back Piece 1 pc.
N. Shelf 2 pcs.
O. Door 2 pcs.
P. Door 2 pcs.
Q. KD. Drawer 2 pcs. (Knock-Down Construction, please refer to the last page of instructions for steps to complete assembling drawers)
HARDWARE LIST Machine Screw for Pull Handle 12 pcs. Hex Wrench 1 pc.
Caster two lock two non-lock 4 pcs.
Cam Lock Screw 6 pcs. (+1 extra)
Head Cap Bolt 12 pcs. (+1extra)
Wood Screw (long) for Drawer Side Part 16 pcs. (+1 extra)
Wood Screw (short) for Drawer Base Part 12 pcs. (+1 extra) Pull Handle 6 pcs.
Wood Screw for Caster 16 pcs. (+1 extra)
Cam Lock Adjustable Pin 6 pcs. (+1 extra) 8 pcs. (+1 extra)
Head Cap Bolt (long) Cross Dowel 7 pcs. (+1extra) 7 pcs. (+1extra)
Tools Required For Assembly : Phillips screwdriver Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
[email protected]
Wood Plug 9 pcs. (+1 extra)
Assembly Instructions 2/5 Wood Screw
IMPORTANT Do not tighten up all the screws until each part is properly assembled. You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
STEP 1
Wood Screw
Attach the two locking Casters to the front of the Base (L). Attach the two non-locking casters to the back of the Base (L). (See figure 1)
L (Figure 1)
(Note : The ‘Arrow’ sticker indicates the front of the base.)
Locking Caster
Upper Position Head Cap Bolt
B H
G H
I
E
J
F H
E
G H
Lower Position Tighten Head Cap Bolt by Hex Wrench.
STEP 2 Attach Back Stretcher (E) to Side Panel (B) at the lower position with Head Cap Bolt. Attach Back Pieces (F) and (G) to the Back Stretcher (E), then slide Back Panels (H) in place. Attach Back Stretcher (E) to the unit at upper position. Tighten the Head Cap Bolt. Attach Front Pieces (I) and (J) to the unit with Head Cap Bolts.
Instructions 3/5
I
C
K
J
F D STEP 3 Attach Divider (K) in between Front Pieces (I) and (J).
Head Cap Bolt
Attach Middle Panel (C) to Back Piece (F). Attach Side Panel (D) to the unit with Head Cap Bolts.
Cross Dowel
L STEP 4 Attach Base (L) from Step 1 to the unit, using Cross Dowels and Head Cap Bolts (long). Head Cap Bolt (long)
Assembly Instructions 4/5 Cam Lock Screw
STEP 5 Put Cam Lock Screws into the pre-drilled holes in Top (A).
A A
Cam Lock
Head Cap Bolt (long)
M
K
Cross Dowel
M N N
Head Cap Bolt
STEP 6 Attach Side Bar (M) to the unit with Head Cap Bolts. Insert the Cross Dowel into the hole of Divider (K) and tighten Head Cap Bolt (long) from the back of unit. Place Top (A) onto the unit, using Cam Locks. Insert Adjustable Pins into the side panels and middle panel at the desired level.
Adjustable Pin
Figure 1
Place Shelves (N) into position.
Q
Figure 2
STEP 7 Attach Pull Handles to the Doors (O) and (P) using Machine Screws. (See figure 1)
O
P
Attach the Doors (O) and (P) to the side panels and middle panel slide the door lift hinges into the side panel and middle panel lift hinges. (See figure 2)
O P
Slide the Drawers (Q) into place. Cover up all holes with Wood Plug. (See figure 3)
Q
Figure 3
Assembly Instructions 5/5
Drawer Q3
Q1
(Figure 1)
STEP 1
Q2 Q4
Attach Q2 to Q3 and Q4 using the long wood screws (4X), tighten halfway. (See figure 1)
MAKE SURE ROLLER IS ON THE BACK
STEP 2
Attach Q1 to Q3 and Q4, using a Phillips screwdriver and the long wood screws (4X), tighten halfway.
Q3
Slide Q5 into the grooves in Q3 and Q4. Be sure to push the Q5 all the way forward so it meets the Q1. (See figure 2)
Q1 (Figure 2)
Q5 Q4 Q2
Q3 Q1 Q5
(Figure 3)
Q2
Q4
(Figure 4)
* If you are missing any of these parts, please contact our DMI Customer Service Department at 1-877-831-0319 or fax us at 1-800-755-2878.
STEP 3 Insert the short wood screws (6X) into the pre-drilled holes in Q5, tighten screws. (See figure 3)
STEP 4 Attach hardware pulls with machine screws. (See figure 4)
Tighten all screws used in drawer assembly.
Part List Q1. Front Part 2 pcs.
Q2. Back Part 2 pcs.
Q3. Side Part 2 pcs.
Q4. Side Part 2 pcs.
Q5. Base Part 2 pcs.
