Transcript
Digital class-D linkable/dual mono block amplifier
9 dB/oct, variable bass boost
Dual MOS-FET PWM power supply
180 Variable phase shift
Stable into 1 ohm load
4 ways protection circuit
24 dB/oct, variable low pass filter
(thermal, voltage, speaker short and DC)
24 dB/oct, variable subsonic filter
Wired remote control included
o
Rated power output ( Tested voltage 14.4Volts )
SAZ-1200D
SAZ-1500D
SAZ-2500D
SAZ-3500D
- RMS power, 2ohm linkable/dual mono
2400W
3000W
5000W
7000W
- RMS power, 1ohm mono
1200W
1500W
2500W
3500W
- RMS power, 2ohm mono
790W
930W
1500W
2500W
- RMS power, 4ohm mono
480W
530W
940W
1350W
35Hz ~ 300Hz
Low pass frequency crossover
10Hz ~ 60Hz
Shusonic filter Bass boost @ 45Hz
0 ~ 9dB
Phase shift control
0 ~ 180 degree 15Hz ~ 270Hz ( +/- 1dB )
Frequency response
6V ~ 0.2V ( +/- 5% )
Input sensitivity
90dB
Signal / noise ratio
< 0.1%
T.H.D @ 4ohm
86%
Efficiency @ 4ohm Fuse Rating
120A
150A
250A
350A
Dimensions ( Length ) inches
12.20
16.53
18.89
24.40
( 8.25 W x 2.32 H ) inches All features are subject to change in the continuing effort to improve the products without notice.
Full range digital 4channel amplifier
12 dB/oct, variable low pass filter
High efficiency 4channel
x1, x10 crossover multiply
Stable into 2 ohm stereo or 4 ohm mono
4 ways protection circuit
12 dB/oct, variable subsonic filter
(thermal, voltage, speaker short and DC)
12 dB/oct, variable high pass filter
Wired remote control included
Rated power output ( Tested voltage 14.4Volts )
SAX-125.4
- RMS power, 4ohm mono
400W x 2CH
- RMS power, 2ohm mono
200W x 4CH
- RMS power, 4ohm mono
125W x 4CH
Subsonic frequency crossover
10Hz ~ 500Hz
High pass frequency crossover
50(500)Hz ~ 500(5K)Hz
High pass frequency multiply
x1, x10
Low pass frequency crossover
50(500)Hz ~ 500(5K)Hz
Low pass frequency multiply
x1, x10
Frequency response
20Hz ~ 20KHz ( +/- 3dB )
Input sensitivity
6V ~ 0.2V ( +/- 5% )
Signal / noise ratio
105dB
T.H.D @ 4ohm
< 0.1%
Efficiency @ 4ohm
70%
Fuse Rating
30A x 2
Dimensions ( Length ) inches
11.02
( 8.25 W x 2.32 H ) inches All features are subject to change in the continuing effort to improve the products without notice.
HEADUNIT
GROUND
BATTERY
Caution
SAZ-1500D, SAZ-2500D & SAZ-3500D are not supplied with internal fuse in themselves. Make sure you install in-line fuse holder from Positive terminal of Battery
+12V Power
Connect the +12V terminal of the amplifier to the POSITIVE terminal of the battery using the same diameter as the ground cable, making sure you install in-line fuse holder, approximately 300 or 400 mm. From the POSITIVE terminal of battery, making sure that there is no fuse in battery holder.
GROUND
Disconnect the battery and connect the GND (ground) terminal to the car’s chassis. Keep this cable as short as possible ( not longer than 20 inches or less ). Making sure that the connection with the chassis is rust free and clear of paint or grime.
REMOTE
Connect the REM terminal of the amplifier to the power antenna terminal in the car ignition switch using 12 or 16 ga electrical wire.
HEADUNIT
Wired Remote Control
8~1ohms
8~2ohms
8~2ohms
Wired Remote Control
HEADUNIT
Remote turn on
8~2ohms
Using a dual amplifier configuration, the MASTER amplifier has total control over the SLAVE amplifier. When using dual amplifier to operate subwoofer, the positive terminal of the subwoofer's voice coil must be connected to the positive terminal of the MASTER Amplifier and the negative terminal of the subwoofer's voice coil must be connected to positive terminal of the SLAVE Amplifier. When hooking two amplifiers to it, please check the power handling capabilities of your subwoofers if they are not exceeded.
HEADUNIT
Wired Remote Control
FULL RANGE DIGITAL 4CHANNEL SPEAKER CONNECTIONS SAX-125.4 3channel speaker connection mode. Tweeter Passive
MidRange /Bass
8~4ohms
SAX-125.4 4channel speaker connection mode. Tweeter Passive
MidRange /Bass
SAX-125.4 4channel speaker connection mode. Tweeter Passive
MidRange /Bass
8~4ohms
SUNDOWN amplifiers have protection features to prevent any damages from misuse or faulty conditions. If SUNDOWN amplifiers sense excessive heat, short circuited speakers DC, or voltage the protection indicator will light, and the system will be turned off. In order to check the problem, you should turn all levels down and all power off and carefully check the installation for wiring mistakes or short. If SUNDOWN amplifiers shut down due to excessive heat, they will be working later when it is cooled down. Before removing your amplifier, refer to the list below and follow the suggested procedures.
NO OUTPUT Check remote turn-on voltage at amplifier and headunit, when remote turn-on voltage is low or no turn-on voltage, there is no sound. Check fuses at the battery side or external fuses and all wire connections. Check RCA Input is properly connecte
AMPLIFIER SHUT DOWN ( PROTECTION ) Please check POWER, GND and REMOTE wire connection and other wires properly connected. When DC over 4V come into the amplifier, amplifier is DC protected. Pls check whether amplifier work after removing RCA-Input. if amplifier work, then check DC by checking RCA-Input. When DC is over 4V at input, try by replacing head-unit or source. When amplifier is over-heated, Amplifier goes into the thermal protection. Amplifier will be back to work after cooling down little bit. Please install amplifier in better ventilation and make it cool. SAZ-1200D, SAZ-1500D, SAZ-2500D & SAZ-3500D have minimum working impedance as 1ohm as single unit. Linkable connection is 2ohm. SAX-125.4 minimum working impedance is 2ohm stereo or 4ohm mono. Make sure Chassis and Remote use same GROUND
DISTORTION & NOISE Please readjust amplifier input level which is printed on endplate. Make sure good ground contact of amplifier or headunit. Use sufficiently shielded RCA interconnects and good RCA routing. Check all ground connections of all other audio equipments.
POOR BASS RESPONSE Check speaker wiring and reverse polarity.
