9200 Lever With Rose Trim Installation Instructions

Transcript

INSTALLATION INSTRUCTIONS 9200 Lever with Rose Trim FOR INSTALLATION ASSISTANCE CALL SARGENT AT 1-800-727-5477 • www.sargentlock.com HOW TO REVERSE LOCK AND FUNCTION 1 HOLE LOCATIONS—SEE OTHER SIDE 7 3 2 5 14 13 11 6 14 12 4 4 9 12 8 10 PARTS LIST DESCRIPTION 1. 2. 3. 4. 5. 6. 7. 1 INSTALL LOCKBODY Inside Lever Setscrew Spring Spindle Outside Rose Screw (2) Adapter & Plate Assy. 2 8. 9. 10. 11. 12. 13. 14. 3 Lockbody Unit Outside Front Mounting Posts Outside Lever Retaining Nuts Inside Rose Washer INSTALL OUTSIDE LEVER ASSEMBLY C INSERT LOCKBODY INTO MORTISE CUTOUT. HOLD LOOSELY IN PLACE WITH (2) LOCKBODY SCREWS. DO NOT TIGHTEN SCREWS AT THIS TIME. A. INSERT SPINDLE INTO OUTSIDE LEVER ASSEMBLY. A B. WITH OUTSIDE LEVER HORIZONTAL , CAREFULLY INSERT THE MOUNTING POSTS THROUGH THE DOOR AND LOCKBODY. MAKE SURE THE SPINDLE IS PROPERLY ENGAGED IN THE LOCK. B 3 4 INSTALL CYLINDER IF CYLINDER IS NOT INCLUDED IN THIS FUNCTION, PROCEED TO STEP 3E. A. SCREW CYLINDER ALONG WITH CYLINDER SPRING AND COLLAR INTO LOCKBODY UNIT. B. AFTER CYLINDER IS SCREWED INTO THE LOCK BODY UNIT, FLUSH WITH THE CYLINDER COLLAR, MAKE CERTAIN THE CYLINDER RETAINER IS LINED UP WITH THE NOTCH ON THE CYLINDER AND THE KEYWAY IS VERTICAL. C. TIGHTEN THE CYLINDER RETAINER TO PREVENT UNSCREWING OF THE CYLINDER. D. TURN THE KEY IN THE CYLINDER TO MAKE CERTAIN THAT THE LOCKING OR LATCHING MECHANISM FUNCTIONS CORRECTLY. C. INSERT SPINDLE INTO SQUARE HOLE ON INSIDE OF DOOR. D. TO SECURE THE ADAPTER AND PLATE ASSEMBLY TO THE INSIDE OF THE DOOR, THREAD THE SCREWS WITH THE LOCK WASHERS D INTO THE MOUNTING POSTS OF THE OUTSIDE LEVER ASSEMBLY. INSTALL INSIDE LEVER A. FIRMLY TIGHTEN TWO SCREWS ON THE INSIDE ADAPTER AND PLATE ASSEMBLY. B. TIGHTLY SCREW THE ROSE TO THE ADAPTER AND PLATE ASSEMBLY. E. TIGHTEN THE LOCKBODY SCREWS. F. SECURE THE OUTSIDE FRONT PLATE TO THE LOCKBODY. G.IF TURN KNOB AND/OR EMERGENCY BUTTON IS INCLUDED, INSTALL IT NOW. (refer to enclosed Instruction Sheet) C. PLACE INSIDE LEVER HORIZONTALLY ONTO SPINDLE. TIGHTEN WITH SIX LOBE SECURITY SCREW DRIVER C Copyright © 2009, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. A7146 1 HOW TO REVERSE LOCK If It Is Necessary To Change Hand of the Latchbolt: If It Is Necessary To Change Hand of Locking Piece 1. Turn lockbody to side NOT marked with RED locking piece. 2. Insert blade screwdriver into locking piece slot. 3. Push locking piece toward front of lockbody and rotate until RED shows. 4. RED indicates locked (outside) side! 1. Remove cap from lock 2. Reverse or turn latchbolt 5 To this Locking guide slot From this Red color locking piece RIGHT HAND SHOWN 9100/9200 TEMPLATE This template covers 9100 & 9200 Series Locksets in accordance with the specifications indicated below. REQUIRED HOLES 7 8 1/4" DIA. 1/4" DIA. 6 1/2" DIA. 1 1/4" DIA. 5 1/2" DIA. 4 03 2 3/4" BACKSET CL OF BOLTS 3 1 1/4" DIA. 7/8" CL OF MOUNTING SCREWS 2 1 1/8" DIA. FUNCTION OUTSIDE FRONT ATTACHING SCREW 1 1 1/8" DIA. FLAT TO 1/8" IN 2" FRONT BEVEL 04 05 1 1/4" 15 SEE STRIKE TEMPLATE FOR DETAILS 7/32" 16 17 CL OF LOCK FRONT 20 21 1" 5/8" 22 23 1 1/32" 1 1/4" 3 7/8" 5/8" (TYP.) 8" 2 1/2" 37 CL OF LEVER OR KNOB 1 3/16" 1" 25 26 7 1/4" 4" 24 CL OF STRIKE 3/8" 11/32" 1 51/64" 65 1/2" 3 5/8" 5/8" MOUNTING SCREWS DRILL & TAP FOR #12-24 X 3/4 SCREW (2 PLACES) 15/16" MIN. 3/4" 2 3/16" REF 4 3 CL OF LOCK FRONT 7/16" (TYP.) 7/16" (TYP.) 5 1" (TYP.) 4 1/8" INSIDE OF DOOR 6" MIN. 6 OUTSIDE OF DOOR 7 8 B 2 1 DETAIL OF SUGGESTED DOOR-CUT 4 DIMENSIONS SHOWN ARE MAXIMUM PART DIMENSIONS 3 SUITABLE REINFORCEMENTS REQUIRED FOR METAL DOORS 2 REFER TO TRIM TEMPLATE FOR ADDITIONAL HOLE REQUIREMENTS 1 2 DENOTES HOLES REQUIRED FOR FUNCTION LISTED. (CHECK BEFORE CUTTING HOLES) Copyright © 2009, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. A7146 SARGENT Manufacturing Company 100 Sargent Drive, New Haven, CT 06511 TEMPLATE: MORTISE LOCK FOR 9100 AND 9200 SERIES (LOCKBODIES ONLY) RELEASE DATE: TEMPLATE NO. 7150A