Transcript
SECTION 5 (Rev.F)
ONE-FAMILY AND TWO-FAMILY KITS
Download from www.urmet.com Technical Manuals area.
SECTION CONTENTS
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND ATLANTICO DOOR PHONE
2
‘2 WIRE’ DOOR PHONE KIT WITH MIKRA PANEL AND UTOPIA DOOR PHONE
7
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND FREE-HANDS DOOR PHONE 14
2-WIRE ONE FAMILY VIDEO KIT
28
One and two-family Video Kit Mod. 956 with ARTICO video door phone
35
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
ONE-FAMILY AND TWO-FAMILY KITS
HANDS-FREE ONE-FAMILY AUDIO KIT 19
sec.5 −−−−
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND UTOPIA DOOR PHONE DEVICES - ACCESSORIES - SPARE PARTS TECHNICAL FEAUTURES - PANEL INSTALLATION
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND UTOPIA DOOR PHONE
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND UTOPIA DOOR PHONE The “audio two” door phone kit is used to make one-family door phone systems with electrical door lock release using only two wires to connect the door phone to the door unit. The following Audio Two door phone kits are available: • With plastic panel Ref. 1129/31 • With zama vandal-proof panel Ref. 1129/41 NOTE: the panels with plastic casing are provided with 35 x 56mm name tags; those with zama casing are provided with 15 x 56mm name tags.
TECHNICAL FEAUTURES Power supply: Transformer output: Transformer power: Protection Electronic: Electrical lock: Power unit-door unit distance: Wire cross-section area: distance = 60m distance = 90m distance = 110m
230Vac ± 10% 50-60Hz 12Vac (nominal) 18VA max. electronic fuse PTC (*) 12Vac Max. 110m 0,5mm2 0,75mm2 1mm2
(*) Disconnect the main power for at least 60” to reset the power unit if the PTC trips due to overload or short-circuit.
Do not use double telephone wires for connections.
PANEL INSTALLATION • Remove the name tag light circuit.
3 2
I PR
1
A conversation can be established by picking up the door phone handset after receiving a call from the door unit. In addition to an auxiliary button for supplementary services (e.g. switching on staircase lights, operating electrical door locks, etc.), the door phone is equipped with a control for adjusting call volume. The ring tone can be selected simply by means of a switch during installation. An additional ringer (Ref. 9854/41) can be connected to the door phone. The additional ringer output level is fixed and does not depend on the door phone ringing level setting. The volumes can be adjusted during installation by means of the loudspeaking unit controls. The name tag on the speaker is back-lit with 2 LEDs. The electric lock can be operated at the end of the conversation by pressing the button on the door phone. A mechanically released electric lock must be used (single pulse opening). Terminals for locally operating a second door or gate opener are also available on the door unit. The maximum distance between the transformer and the door unit must be less than 110m.
ø 4 mm
• Extract the door unit from the base.
ONE-FAMILY AND TWO-FAMILY KITS
DEVICES The base kit has the following devices: • Utopia door phone with door opening button and 1 supplementary button. • Smyle Door speaker unit with one call button. • Power transformer 230/12Vac.
ACCESSORIES The following accessories may be purchased separately: • Additional ringer Ref. 9854/41 • Additional door phone buttons Ref. 1134/55 • Supplementary door phone (6 wires) Ref. 1129/52
−−−− sec.5
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND UTOPIA DOOR PHONE PANEL INSTALLATION
• Write the name on the name tag and insert in the housing.
The panels with plastic casing may also be fixed in a flushmounting box Mod. 503 as shown below.
Rossi
Mod. 503
CLI iss
oR
• Insert the front part of the panel on the base and fasten it with the socket head screw using the wrench (2mm) provided.
ONE-FAMILY AND TWO-FAMILY KITS
• Insert the door unit into the compartment in the based and connect the wires (it is advisable to have approximately 40-45mm of wire protruding from the wall).
CK
• Fasten the name tag light circuit making the wires pass underneath the support.
CLI
CK
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND UTOPIA DOOR PHONE
• Adjust volume. Volume is calibrated to optimal values during production. Change the settings when needed only.
1,55 m ÷ 1,65 mm
• Fasten the base onto a flat wall at the height shown in the figure using the bolts provided.
sec.5 −−−−
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND UTOPIA DOOR PHONE APARTMENT STATION INSTALLATION TRANSFORMER INSTALLATION
ONE-FAMILY AND TWO-FAMILY KITS
ADJUSTING THE CALL VOLUME
To remove the door phone top, lever with the tip of a screwdriver in the area shown and remove it by turning it on the upper tabs.
Red MAX Maximum calling volume
MIN Minimu calling volume
MUTE No calling tone
TRANSFORMER INSTALLATION Use the holes on the base to fasten the door phone to the wall. Use the bolts provided with each device. 1 (default)
2
2
Before connecting the transformer to the mains, disconnect the mains switch. Fit the protective cover on the network terminals after connecting the system. Disconnect the mains power supply for 60” to reset the transformer if the PTC thermal switch trips due to overload or short-circuit. Use lever “A” to remove the transformer fitted on a DIN rail.
1
Fitting to DIN rail Calling tone: 1= Tone 1 2= Tone 2
2
1
1,55 m
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND UTOPIA DOOR PHONE
APARTMENT STATION INSTALLATION
PR
I
A
Wall fitting
Select the ring tone before closing the hood.
Refit the door phone top after installation.
NO
OK
Insert the handset telephone plug connector in the door phone base.
−−−− sec.5
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND UTOPIA DOOR PHONE WIRING DIAGRAMS
A total of up to 5 devices (1 main door phone and 4 door phones Ref.1129/52). Only 1 supplementary ringer ref. 9854/41 can be connected to the system (terminals S+, S-). The ringer connected to terminals S+ and S- of the main door phone is subjected to calling volume setting of the main door phone.
BASIC WIRING DIAGRAM
SC101-1427 AP2 AP2
Gate opening contact (MAX 1A 120Vac)
C NA 12 ~12 ~0
Mains~
2 1
2 1
S- S+
Door phone ~
~
AP1 AP1
~~ 12 0
Transformer
K
SE1 SE2
Z
Electric lock Additional ringer Ref.9854/41
LOCK RELEASE FROM HALL BUTTON CONNECTION DIAGRAM
SC101-1427
12
~
~
2 1
2 1
1
S- S+
~~ 12 0
Door release button
Transformer
AP1 AP1 SE1 SE2
ONE-FAMILY AND TWO-FAMILY KITS
~12 ~0
Mains~
Electric lock
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND UTOPIA DOOR PHONE
WIRING DIAGRAMS
sec.5 −−−−
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND UTOPIA DOOR PHONE WIRING DIAGRAMS
Connection of a supplementary door phone in parallel to a main door phone in a one-family 2-wire audio kit
SC101-1428
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND UTOPIA DOOR PHONE
2
12
12 0
1 2C S+ S-
Additional door phone Ref.1129/52
SS+ 2 1
Door phone
Mains~
~
~
Push button panel
~12 ~0
2 1
Transformer SE1 SE2
Electric lock
Connection of 4 supplementary door phones in parallel to a main door phone in a one-family 2-wire audio kit
SC101-1429
2
12
1 S+ 2C S-
2
12
ONE-FAMILY AND TWO-FAMILY KITS
12 0
Mains~
~
~
~12 ~0
2
Additional door phone Ref.1129/52
1 S+ 2C S-
2
12
3
1 S+ 2C S2
12
4
1
1 S+ 2C S-
S2 S+ 1
Door phone Push button panel 2 1
Transformer SE1 SE2
Electric lock
−−−− sec.5
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
2 WIRE DOOR PHONE KIT WITH MIKRA PANEL AND UTOPIA DOOR PHONE DEVICES - ACCESSORIES - SPARE PARTS TECHNICAL FEAUTURES - PANEL INSTALLATION
The door phone kit is used to make one-family door phone systems with electrical door lock release using only two wires to connect the door phone to the door unit. The following door phone kits are available: • 230Vac 50Hz power supply Ref. 1122/31 • 110Vac 60Hz power supply Ref. 1122/39
(*) Disconnect the main power for at least 60” to reset the power unit if the PTC trips due to overload or short-circuit.
Do not use double telephone wires for connections.
PUSH BUTTON PANEL INSTALLATION SURFACE MOUNTING • Remove the front cover.
3 2
I
PR
1
A conversation can be established by picking up the door phone handset after receiving a call from the door unit. In addition to an auxiliary button for supplementary services (e.g. switching on staircase lights, operating electrical door locks, etc.), the door phone is equipped with a control for adjusting call volume. The ring tone can be selected simply by means of a switch during installation. An additional ringer (Ref. 9854/41) can be connected to the door phone. The additional ringer output level is fixed and does not depend on the door phone ringing level setting. The volumes can be adjusted during installation by means of the loudspeaking unit controls. The name tag on the speaker is back-lit with 2 LEDs. The electric lock can be operated at the end of the conversation by pressing the button on the door phone. A mechanically released electric lock must be used (single pulse opening). Terminals for locally operating a second door or gate opener are also available on the door unit. The maximum distance between the transformer and the door unit must be less than 110m.
• Fix the base on a level wall, at the height shown in the figure, using the provided screw anchors.
DEVICES
ACCESSORIES The following accessories may be purchased separately: • Additional ringer Ref. 9854/41 • Additional door phone buttons Ref. 1134/55 • Supplementary door phone (6 wires) Ref. 1129/52 • Flush mounting box with push button panel. Ref. 1122/60
ONE-FAMILY AND TWO-FAMILY KITS
1,55 ÷ 1,60 m
The base kit has the following devices: • Utopia door phone with door opening button and 1 supplementary button. • Mikra Door speaker unit with one call button. • Power transformer.
• Perform connections.
TECHNICAL FEAUTURES Power supply Ref. 1122/31: Power supply Ref. 1122/39: Transformer output: Transformer power: Protection Electronic: Electrical lock: Power unit-door unit distance: Wire cross-section area: distance = 60m distance = 90m distance = 110m
230Vac ± 10% 50Hz 110Vac ± 10% 60Hz 12Vac (nominal) 18VA max. electronic fuse PTC (*) 12Vac Max. 110m 0,5mm2 0,75mm2 1mm2
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
2 WIRE DOOR PHONE KIT WITH MIKRA PANEL AND UTOPIA DOOR PHONE
2 WIRE DOOR PHONE KIT WITH MIKRA PANEL AND UTOPIA DOOR PHONE
sec.5 −−−−
2 WIRE DOOR PHONE KIT WITH MIKRA PANEL AND UTOPIA DOOR PHONE PUSH BUTTON PANEL INSTALLATION
Flush mounting • Remove the push button panel front.
• Fill in the name holder and put it in its seat.
1,55 ÷ 1,60 m
• Install the flush mounting box Ref. 1122/60 (it must be purchased separately) at the height indicated.
• Fix the base of the push button panel to the frame provided with the flush mounting box.
ONE-FAMILY AND TWO-FAMILY KITS
2 WIRE DOOR PHONE KIT WITH MIKRA PANEL AND UTOPIA DOOR PHONE
• Adjust audio levels: these are set to optimal values during production, it is suggested to change them only if it is needed.
CLICK
−−−− sec.5
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
2 WIRE DOOR PHONE KIT WITH MIKRA PANEL AND UTOPIA DOOR PHONE PUSH BUTTON PANEL INSTALLATION
• Chiudere la pulsantiera con la copertura metallica.
2 WIRE DOOR PHONE KIT WITH MIKRA PANEL AND UTOPIA DOOR PHONE
• Put the frame with the base in the flush mounting box, and make cables come out of the hole.
The connection cables must come out of 20 cm at least.
• Perform connections.
• Remove the frame from the base by pressing the locks.
ONE-FAMILY AND TWO-FAMILY KITS
• Fix the push button panel to the frame.
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
sec.5 −−−−
2 WIRE DOOR PHONE KIT WITH MIKRA PANEL AND UTOPIA DOOR PHONE PUSH BUTTON PANEL INSTALLATION
2,9x9,5mm self-tapping screws
• Screw the frame with the push button panel to the flush mounting box.
2,9x16mm self-tapping screws
• Complete the installation by fixing the frame.
ONE-FAMILY AND TWO-FAMILY KITS
2 WIRE DOOR PHONE KIT WITH MIKRA PANEL AND UTOPIA DOOR PHONE
• Screw the frame to the push button panel base.
10 −−−− sec.5
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
2 WIRE DOOR PHONE KIT WITH MIKRA PANEL AND UTOPIA DOOR PHONE APARTMENT STATION INSTALLATION TRANSFORMER INSTALLATION
APARTMENT STATION INSTALLATION To remove the door phone top, lever with the tip of a screwdriver in the area shown and remove it by turning it on the upper tabs.
Red MAX Maximum calling volume
MIN Minimu calling volume
MUTE No calling tone
TRANSFORMER INSTALLATION Use the holes on the base to fasten the door phone to the wall. Use the bolts provided with each device. 1 (default)
2
2
Before connecting the transformer to the mains, disconnect the mains switch. Fit the protective cover on the network terminals after connecting the system. Disconnect the mains power supply for 60” to reset the transformer if the PTC thermal switch trips due to overload or short-circuit. Use lever “A” to remove the transformer fitted on a DIN rail.
1
Fitting to DIN rail 2
1
1,55 m
Calling tone: 1= Tone 1 2= Tone 2
PR
I
A
Wall fitting
Select the ring tone before closing the hood.
2 WIRE DOOR PHONE KIT WITH MIKRA PANEL AND UTOPIA DOOR PHONE
ADJUSTING THE CALL VOLUME
NO
ONE-FAMILY AND TWO-FAMILY KITS
Refit the door phone top after installation.
OK
Insert the handset telephone plug connector in the door phone base.
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
sec.5 −−−− 11
2 WIRE DOOR PHONE KIT WITH MIKRA PANEL AND UTOPIA DOOR PHONE WIRING DIAGRAMS
2 WIRE DOOR PHONE KIT WITH MIKRA PANEL AND UTOPIA DOOR PHONE
WIRING DIAGRAMS
A total of up to 5 devices (1 main door phone and 4 door phones Ref.1129/52). Only 1 supplementary ringer ref. 9854/41 can be connected to the system (terminals S+, S-). The ringer connected to terminals S+ and S- of the main door phone is subjected to calling volume setting of the main door phone.
BASIC WIRING DIAGRAM
SC101-1427 AP2 AP2
Gate opening contact (MAX 1A 120Vac)
C NA 12 ~12 ~0
Mains~
2 1
2 1
S- S+
Door phone ~
~
AP1 AP1
~~ 12 0
Transformer
K
SE1 SE2
Z
Electric lock Additional ringer Ref.9854/41
LOCK RELEASE FROM HALL BUTTON CONNECTION DIAGRAM
SC101-1427
12 ~12 ~0
Mains~
~
~
2 1
1
S- S+
~~ 12 0
Transformer
ONE-FAMILY AND TWO-FAMILY KITS
2 1
Door release button
AP1 AP1 SE1 SE2
Electric lock
12 −−−− sec.5
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
2 WIRE DOOR PHONE KIT WITH MIKRA PANEL AND UTOPIA DOOR PHONE WIRING DIAGRAMS
Connection of a supplementary door phone in parallel to a main door phone in a one-family 2-wire audio kit
SC101-1428
12
12 0
1 2C S+ S-
Additional door phone Ref.1129/52
SS+ 2 1
Door phone
Mains~
~
~12 ~0
2 1
Transformer SE1 SE2
Electric lock
Connection of 4 supplementary door phones in parallel to a main door phone in a one-family 2-wire audio kit
SC101-1429
2
12
1 S+ 2C S-
2
12
12 0
Mains~
~
~
2
Additional door phone Ref.1129/52
1 S+ 2C S-
2
12
3
1 S+ 2C S2
12
4
1
1 S+ 2C S-
S2 S+ 1
~12 ~0
Door phone Push button panel 2 1
Transformer SE1 SE2
Electric lock DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
sec.5 −−−− 13
ONE-FAMILY AND TWO-FAMILY KITS
~
Push button panel
2 WIRE DOOR PHONE KIT WITH MIKRA PANEL AND UTOPIA DOOR PHONE
2
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND FREE-HANDS DOOR DEVICES - ACCESSORIES - SPARE PARTS TECHNICAL FEAUTURES - PANEL INSTALLATION
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND UTOPIA DOOR PHONE
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND FREE-HANDS DOOR PHONE The “audio two” door phone kit is used to make one-family door phone systems with electrical door lock release using only two wires to connect the door phone to the door unit. The following Audio Two door phone kits are available: • With plastic panel Ref. 1129/61 • With zama vandal-proof panel Ref. 1129/71
The panels with plastic casing are provided with 35 x 56mm name tags; those with zama casing are provided with 15 x 56mm name tags.
TECHNICAL FEAUTURES Power supply: Transformer output: Transformer power: Protection Electronic: Electrical lock: Power unit-door unit distance: Wire cross-section area: distance = 60m distance = 90m distance = 110m
230Vac ± 10% 50-60Hz 12Vac (nominal) 18VA max. electronic fuse PTC (*) 12Vac Max. 110m 0,5mm2 0,75mm2 1mm2
(*) Disconnect the main power for at least 60” to reset the power unit if the PTC trips due to overload or short-circuit.
Do not use double telephone wires for connections.
PANEL INSTALLATION • Remove the name tag light circuit. PR
I
A conversation can be established by pressing the door phone button after receiving a call from the door unit. In addition to an auxiliary button for supplementary services (e.g. switching on staircase lights, operating electrical door locks, etc.), the door phone is equipped with a control for adjusting call volume. Maximum, minimum or mute volume can be selected. An additional ringer (Ref. 9854/41) can be connected to the door phone. The additional ringer output level is fixed and does not depend on the door phone ringing level setting. The volumes can be adjusted during installation by means of the loudspeaking unit controls. The name tag on the speaker is back-lit with 2 LEDs. The electric lock can be operated at the end of the conversation by pressing the button on the door phone. A mechanically released electric lock must be used (single pulse opening). Terminals for locally operating a second door or gate opener are also available on the door unit. The maximum distance between the transformer and the door unit must be less than 110m.
ø 4 mm
• Extract the door unit from the base.
ONE-FAMILY AND TWO-FAMILY KITS
DEVICES The base kit has the following devices: • Utopia free-hands door phone with door opening button and 1 supplementary button. • Smyle Door speaker unit with one call button. • Power transformer 230/12Vac.
ACCESSORIES The following accessories may be purchased separately: • Additional ringer Ref. 9854/41 • Supplementary door phone (5 wires) Ref. 1129/62
14 −−−− sec.5
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND FREE-HANDS DOOR PANEL INSTALLATION
• Write the name on the name tag and insert in the housing.
The panels with plastic casing may also be fixed in a flushmounting box Mod. 503 as shown below.
Rossi
Mod. 503
CLI iss
oR
• Insert the front part of the panel on the base and fasten it with the socket head screw using the wrench (2mm) provided.
ONE-FAMILY AND TWO-FAMILY KITS
• Insert the door unit into the compartment in the based and connect the wires (it is advisable to have approximately 40-45mm of wire protruding from the wall).
CK
• Fasten the name tag light circuit making the wires pass underneath the support.
CLI
CK
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND UTOPIA DOOR PHONE
• Adjust volume. Volume is calibrated to optimal values during production. Change the settings when needed only.
1,55 m ÷ 1,65 mm
• Fasten the base onto a flat wall at the height shown in the figure using the bolts provided.
sec.5 −−−− 15
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND FREE-HANDS DOOR APARTMENT STATION INSTALLATION TRANSFORMER INSTALLATION
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND UTOPIA DOOR PHONE
APARTMENT STATION INSTALLATION
Refit the door phone top after installation.
To remove the door phone top, lever with the tip of a screwdriver in the area shown and remove it by turning it on the upper tabs.
ADJUSTING THE CALL VOLUME Use the holes on the base to fasten the door phone to the wall. Use the bolts provided with each device. ON ON FREE-HANDS (default) Red
OFF
MAX Maximum calling volume
ON OFF AUDIO WITH BUTTON PRESSED
MIN Minimu calling volume
MUTE No calling tone
OFF
1 (default)
TRANSFORMER INSTALLATION 2
Before connecting the transformer to the mains, disconnect the mains switch. Fit the protective cover on the network terminals after connecting the system. Disconnect the mains power supply for 60” to reset the transformer if the PTC thermal switch trips due to overload or short-circuit. Use lever “A” to remove the transformer fitted on a DIN rail.
Calling tone: 1= Tone 1 2= Tone 2 1
Fitting to DIN rail
ONE-FAMILY AND TWO-FAMILY KITS
PR
I
A
Wall fitting
Select the ring tone and the audio activation mode before closing the hood.
NO
16 −−−− sec.5
OK
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND FREE-HANDS DOOR WIRING DIAGRAMS
A total of up to 5 devices (1 main door phone and 4 door phones Ref. 1129/62). Only 1 supplementary ringer Ref. 9854/41 can be connected. The ringer must be connected to the terminals K and Z. The ringer volume can be adjusted by adjusting the calling volume of the door phone.
BASIC WIRING DIAGRAM
SC101-1440
AP2 AP2
~12 L ~0 ~0 AP K Z
Mains~
~
~
Gate opening contact (MAX 1A 120Vac)
C NA
Door phone
L ~0
Open door signalling contact (NO if door closed)
AP1 AP1 SE1 SE2
~~ 12 0
Transformer Electric lock K
Z
Additional ringer Ref.9854/41
LOCK RELEASE FROM HALL BUTTON CONNECTION DIAGRAM
SC101-1440
Door phone 12 ~12 L ~0 ~0
Mains~
K ~
~
~~ 12 0
Z
Door release button
L ~0 AP1 AP1 SE1 SE2
ONE-FAMILY AND TWO-FAMILY KITS
Transformer Electric lock
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND UTOPIA DOOR PHONE
WIRING DIAGRAMS
sec.5 −−−− 17
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND FREE-HANDS DOOR WIRING DIAGRAMS
Connection of a supplementary door phone in parallel to a main door phone in a one-family 2-wire audio kit
ONE-FAMILY AND TWO-FAMILY KITS
‘AUDIO TWO’ DOOR PHONE KIT WITH SMYLE PANEL AND UTOPIA DOOR PHONE
SC101-1441
~12
S ~12 ~0
L ~0 ~0 L1 Z K
Additional door phone Ref.1129/62
K Z L ~0
Door phone Push button panel
Mains~ L ~0 ~
~
~12 ~0
Transformer
SE1 SE2
Electric lock Connection of 4 supplementary door phones in parallel to a main door phone in a one-family 2-wire audio kit
SC101-1442
S ~12
S ~12
S ~12
S ~12
S ~12 ~0
Mains~
~
~
~12 ~0
L ~0 ~0 Z L1 K L ~0 ~0 Z L1 K L ~0 ~0 Z L1 K L ~0 ~0 Z L1 K
K L Z ~0
4
3
2
Additional door phone Ref.1129/62
1
Door phone Push button panel L ~0
Transformer SE1 SE2
Electric lock
18 −−−− sec.5
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
Ref. 1122/61
HANDS-FREE ONE-FAMILY AUDIO KIT Ref. 1122/61 GENERAL DESCRIPTION - KIT COMPOSITION - ACCESSORY DEVICES
KIT COMPOSITION
A
N°
Mikra panel
1
A1
Screws for fixing to wall
4
A2
Bolts for fastening to wall Ø 5mm
4
A3
Screwdriver insert
1
A4
Name tag
1
A5
Front closing screw
1
A6
1
B1
Screws for fastening to wall
2
B2
Bolts for fastening to wall Ø 6mm
2
B3
Transformer
1
C
Utopia phone
“Master”
door
ID
Apartment station
GENERAL DESCRIPTION The one-family audio door phone kit is characterised by simple installation using only two wires to connect the door phone to the power supply and the door phone to the calling station. The following door phone kits are available: 230Vac 50Hz power supply Ref. 1122/61 110Vac 60Hz power supply Ref. 1122/69 The main characteristics of the system are: System • Possibility of managing up to 5 door phones (1 “Master” and 4 “Slave”) called in parallel. • No local wiring needed on calling stations or “Slave” apartment stations. • Free pedestrian door lock activation for as long as the button on the door phone is pressed. • Activation of a potential-free closing contact for controlling electric loads or activating garage gate lock. • Three-minute conversation time between calling station and door phone. • All devices comply with CE directives in the matter of electromagnetic compatibility and to the low voltage directive. • The system is intrinsically protected from static and pulse electromagnetic interference. Calling station • Calling station with weatherproof aluminium front panel (IP44). • Backlit white name holder tag. • Call forward confirmation by turning name tag backlighting LEDs off. • Ready for connecting two hall buttons for activating electric locks. Apartment station • Hands-free apartment stations with half-duplex audio. • Dedicated audio, pedestrian lock and garage gate buttons. • Hands-free or push-to-talk: - Hands-free: press the audio button once to start the conversation and once again to end it. - Push-to-talk: keep the audio button pressed to talk to the calling station and release it to end the conversion. • Calling tones selectable by user (five available tones). • Adjustable calling volume with mute function. • Possibility of connecting a supplementary ringer to each door phone. • Setup for connecting a door open indicator sensor. • Audio on LED (blue) and door open LED (red).
B
Power supply units
C
HANDS-FREE ONE-FAMILY AUDIO KIT
Calling station
Description
ACCESSORY DEVICES Description
Electric lock Max 15VA)
(12V
N° max (maximum system configuration)
ID
1
OP1
Supplementary ringer
Ref.9854/41
5 (one for each apartment station)
OP2
Supplementary “Slave” door phones
Ref.1122/62
4
OP3
Hall button for operating pedestrian electric lock
1
OP4
Hall button for operating garage gate lock
1
OP5
Garage gate lock activation device (max switching current 1A @ 30V)
1
OP6
Door open (NO with closed)
1
OP7
1
OP8
sensor door
Mikra panel flushmounting box
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
Ref.1122/60
sec.5 −−−− 19
ONE-FAMILY AND TWO-FAMILY KITS
HANDS-FREE ONE-FAMILY AUDIO KIT Ref. 1122/61
Ref. 1122/61
HANDS-FREE ONE-FAMILY AUDIO KIT Ref. 1122/61 CONNECTION BLOCK CHART
HANDS-FREE ONE-FAMILY AUDIO KIT
CONNECTION BLOCK CHART BASIC SYSTEM
2
2
B
OP4
2
OP5
2
Master
C
2
A
Mains
OP6 2
OP1
Max 180 m with 1,5 mm2 cross-section area
SYSTEM IN MAXIMUM CONFIGURATION OP7
2
OP4
2
OP5
OP2 2
2 2
2
B Master
C
Mains
4
A
2
OP2
OP6
2 2
OP3
OP1
Slave
OP2
4
2
OP3 Slave
OP2
4
2
OP3
OP2
Slave
ONE-FAMILY AND TWO-FAMILY KITS
2
4
OP3 Slave
MAXIMUM DISTANCE BETWEEN DEVICES Segment C - OP1 A - OP4 A - OP5 B - OP3 most distant B - OP2 OP3 - OP2
20 −−−− sec.5
wire cross-section areas 0,5 mm2 0,75 mm2 1 mm2 1,5 mm2 60 m 90 m 120 m 180 m 60 m 90 m 120 m 180 m 60 m 90 m 120 m 180 m 90 m 120 m 250 m 320 m 60 m
90 m
120 m
180 m
L’impianto può funzionare con i seguenti cavi multipli: • cavo multiplo dia. 0,6 mm (0,26 mm2) Mettendo 2 fili in parallelo per ogni linea, il cavo dia. 0,6 mm può essere paragonato ad un cavo di sezione da 0,5 mm2. Mettendo 4 fili in parallelo per ogni linea, il cavo dia. 0,6 mm può essere paragonato ad un cavo di sezione da 1 mm2. • cavo multiplo dia. 0,8 mm (0,5 mm2)
Mettendo 2 fili in parallelo per ogni linea, il cavo dia. 0,8 mm può essere paragonato ad un cavo di sezione da 1 mm2. Mettendo 4 fili in parallelo per ogni linea, il cavo dia. 0,8 mm può essere paragonato ad un cavo di sezione da 1,5 mm2.
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
Ref. 1122/61
HANDS-FREE ONE-FAMILY AUDIO KIT Ref. 1122/61 “MASTER” DOOR PHONE INSTALLATION
The functions of the dip-switches instead are: ON 1 2
dip-switch n°1 ON 1 2
hands-free: press the button to turn audio on, press again to turn it off (default) press-to-talk: hold the button pressed for the entire conversation; communication is interrupted when the button is released (dip switch 2)
ON
immediate call tone (default) dip-switch n°2
1 2 ON
delay call tone 1 2
1,50 m
If several supplementary door phones are installed, it is advisable to set dip switch 2 in alternating manner on the door phones (first door phone on, second door phone off, third door phone on and so forth).
“MASTER” DOOR DESCRIPTION
PHONE
TERMINALS
HANDS-FREE ONE-FAMILY AUDIO KIT
“MASTER” DOOR PHONE INSTALLATION
0 ground for calling station 0/K ground for supplementary ringer and/or “slave” door phones Z supplementary ringer output S output for “slave” door phone power ~0 power ground ~/+ 12Vac power AP open door signal input L calling station connection line L1 “slave” door phone connection line
“MASTER” DOOR COMPLETION
PHONE
INSTALLATION
“MASTER” DOOR PHONE CONFIGURATION JP1
ONE-FAMILY AND TWO-FAMILY KITS
JP2
SW
The door phone may be configured as master or slave by means of two JP1 and JP2 jumpers. JP1
JP2
Master (default)
pos. “P”
pos. “P”
Slave
pos. “S”
pos. “S”
Both jumpers must be in the same position.
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
sec.5 −−−− 21
Ref. 1122/61
HANDS-FREE ONE-FAMILY AUDIO KIT Ref. 1122/61 TRANSFORMER INSTALLATION - CALLING STATION INSTALLATION
TRANSFORMER INSTALLATION
3
HANDS-FREE ONE-FAMILY AUDIO KIT
The device must be installed in the electric panel or a cabinet.
A3
1,55 ÷ 1,60 m
A2
CONNECTING THE POWER SUPPLY To master door phone
5 Mains
DESCRIPTION OF TERMINALS INPUT Mains power input OUTPUT 12Vac door phone system power output
ONE-FAMILY AND TWO-FAMILY KITS
CALLING STATION INSTALLATION
1
2
6
A5
7 A4
22 −−−− sec.5
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
Ref. 1122/61
HANDS-FREE ONE-FAMILY AUDIO KIT Ref. 1122/61 “SLAVE” DOOR PHONE INSTALLATION
L
0 SE1 SE2 C NA
AP2
AP1
HANDS-FREE ONE-FAMILY AUDIO KIT
“SLAVE” DOOR PHONE INSTALLATION
CALLING STATION CONNECTION
Hall button for pedestrian electric lock (OP4)
To master door phone
Garage gate opener (OP6)
Hall button for garage gate lock (OP5)
1,50 m
Pedestrian door electric lock (OP1)
DESCRIPTION OF TERMINALS
} } }
L 0 SE1 SE2 C NA AP1 AP2
Audio, power and signal line from “Master” door phone Pedestrian electric lock operation (OP1) – maximum switch 12V Max 15VA Garage gate opener operation dry contact (OP6) – maximum switch 1A @ 30V Terminal pair for hall button for pedestrian electric lock (OP4) Terminal pair for hall button for garage gate opener (OP5)
INSTALLATION COMPLETION 8
9
“SLAVE” DOOR PHONE CONFIGURATION JP1
A4
The door phone may be configured as master or slave by means of two JP1 and JP2 jumpers. JP1 Master
Slave (default)
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
JP2
pos. “P”
pos. “P”
pos. “S”
pos. “S”
Both jumpers must be in the same position.
sec.5 −−−− 23
ONE-FAMILY AND TWO-FAMILY KITS
JP2
SW
Ref. 1122/61
HANDS-FREE ONE-FAMILY AUDIO KIT Ref. 1122/61 OPERATION
OPERATION
The functions of the dip-switches instead are:
HANDS-FREE ONE-FAMILY AUDIO KIT
ON 1 2
dip-switch n°1
ON 1 2
hands-free: press the button to turn audio on, press again to turn it off (default)
2
press-to-talk: hold the button pressed for the entire conversation; communication is interrupted when the button is released
1
3
ON
immediate call tone (default) dip-switch n°2
1 2 ON
4
delay call tone 1 2
5
If several supplementary door phones are installed, it is advisable to set dip switch 2 in alternating manner on the door phones (first door phone on, second door phone off, third door phone on and so forth).
“SLAVE” DOOR PHONES CONNECTION Master door phone JP1=P JP2=P SW1=Off SW2=Off
0 0/K Z S ~0 ~/+AP L L1
To call station
Slave door phone JP1=S JP2=S SW1=Off SW2=On
0 0/K Z S ~0 ~/+AP L L1
To the transformer
Slave door phone JP1=S JP2=S SW1=Off SW2=Off
0 0/K Z S ~0 ~/+AP L L1
1. Switch for adjusting calling volume
Slave door phone JP1=S JP2=S SW1=Off SW2=On
Maximum calling volume Slave door phone JP1=S JP2=S SW1=Off SW2=Off
0 0/K Z S ~0 ~/+AP L L1
“SLAVE” DOOR PHONE TERMINALS DESCRIPTION 0 0/K Z S ~0 ~/+ AP L L1
ground for calling station ground for supplementary ringer supplementary ringer output output for next “slave” door phone power ground for calling station 12Vac power open door signal input previous “slave” door phone connection line next “slave” door phone connection line
“slave” DOOR COMPLETION
PHONE
6
Red
0 0/K Z S ~0 ~/+AP L L1
ONE-FAMILY AND TWO-FAMILY KITS
DOOR PHONE FRONT DESCRIPTION
Minimum calling volume
No calling tone
2. Pedestrian door opener button 3. Door open indicator LED (only if system setup includes this function) 4. Garage gate door opener button 5. Audio on/off button 6. Audio state activation LED Off: system in stand-by Steady on: audio on (communication in progress) Slow flashing: call in progress Fast flashing: system busy (another door phone is communicating with the calling station)
CALL TONE SELECTION Proceed as follows with the system in stand-by to select the call tone:
INSTALLATION
1. Hold the pedestrian door and the garage gate opening button at the same time pressed for one second. The door phone will output the call tone currently in use. 2. Holding the garage gate opening button pressed, release and press the pedestrian door opening button and wait for the next call tone. 3. Release both buttons when you hear the required call tone.
24 −−−− sec.5
The doors may be opened by mistake if the buttons are not pressed at the same time.
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
Ref. 1122/61
HANDS-FREE ONE-FAMILY AUDIO KIT Ref. 1122/61 TECHNICAL SPECIFICATIONS
CALL MANAGEMENT
HANDS-FREE ONE-FAMILY AUDIO KIT
The following events will occur when the calling button is pressed: • The name tag backlighting will go off for a time. • The door phones will emit a call tone according to the priority defined by dip switch 2 (if mute function is not selected). • The blue LED on all the door phones will start blinking. The user can activate audio and start a conversion with the caller for three minutes. To establish a conversation, in “hands-free” mode, briefly press , in “push-to-talk”, hold pressed. The following events will occur when audio is turned on: • The name tag backlighting goes out for as long as the conversation is in progress. • The door phone blue audio LED will light up fixed. • The blue LED of the other door phones will start blinking rapidly to indicate busy state. To end the conversation before the three minute timeout, in “handsfree” mode, briefly press , in “push-to-talk”, release .
AUTO-ON Audio can be turned on from any of the door phones at any time (with the procedure of the chosen operating mode) to establish communication with the calling station even when the system is standing by. The following events will occur when audio is turned on: • The name tag backlighting goes out for as long as the conversation is in progress. • The door phone blue audio LED will light up fixed. • The blue LED of the other door phones will start blinking rapidly to indicate busy state.
ELECTRIC LOCK ACTIVATION At any time, even with the system standing by, the pedestrian electric lock can be activated by pressing or the garage gate by pressing the system button on any of the door phones in the system.
DOOR OPEN INDICATION If the system was set up with the devices needed for this function (OP7), the red LED next to the door opening button will light up when the door onto which the contact is fitted is open.
TECHNICAL SPECIFICATIONS
Door phone Power voltage: Consumption During call: Stand-by: With audio on: Working temperature range: Max. humidity: Dimensions (WxDxH) Calling station Name tag dimensions: Tag and button light: Degree of protection: Working temperature range: Max. humidity: Max. capacity C-NO contact Max. capacity SE1-SE2 contact Dimensions (WxDxH)
ONE-FAMILY AND TWO-FAMILY KITS
Transformer Power: 230 Vac, 50-60 Hz or 110 Vac 50-60 Hz Power: 12VA Secondary output: 12 Vac 1.1 A Dissipated power after 1 working hour: Max 1.8W Dimensions (WxDxH) 54 (3 DIN modules) x 83 x 58 mm 12Vac 1A 350 mA 700 mA -5° - +45° C 90% RH 90 x 38 x 195 mm 55 x 25 mm LED IP44 as per CEI 70.1 -10° - +50° C 90% RH 1A @ 30V 12V Max 15VA 100 x 180 x 25 mm
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
sec.5 −−−− 25
Ref. 1122/61
HANDS-FREE ONE-FAMILY AUDIO KIT Ref. 1122/61 WIRING DIAGRAM
HANDS-FREE ONE-FAMILY AUDIO KIT
WIRING DIAGRAM BASIC SYSTEM WIRING DIAGRAM
SC101-1511
“MASTER” DOOR PHONE GARAGE GATE CONTACT GARAGE GATE LOCK ACTIVATION DEVICE
TRASFORMER
MIKRA PANEL MAIN~
Ref.9000/230
HALL BUTTON FOR OPERATING GARAGE GATE LOCK HALL BUTTON FOR OPERATING PEDESTRIAN ELECTRIC LOCK
ONE-FAMILY AND TWO-FAMILY KITS
ELECTRIC LOCK
26 −−−− sec.5
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
Ref. 1122/61
HANDS-FREE ONE-FAMILY AUDIO KIT Ref. 1122/61 WIRING DIAGRAM
WIRING DIAGRAM FOR SYSTEM IN MAXIMUM CONFIGURATION
SC101-1510 HANDS-FREE ONE-FAMILY AUDIO KIT
SUPPLEMENTARY “SLAVE” DOOR PHONE Ref.1122/62
AP S L1 ~0 L 0 ~/+ 0/K Z
5 SLAVE
Ref.9854/41
SUPPLEMENTARY RINGER AP S L1 ~0 L 0 ~/+ 0/K Z
4 SLAVE
Ref.9854/41
SUPPLEMENTARY RINGER AP S L1 ~0 L 0 ~/+ 0/K Z
3 SLAVE
Ref.9854/41
SUPPLEMENTARY RINGER
AP S L1 ~0 L 0 ~/+ 0/K Z
2 SLAVE
Ref.9854/41
AP S L1 0 L ~0 ~/+ 0/K Z
1 “MASTER” DOOR PHONE
GARAGE GATE CONTACT Ref.9854/41
GARAGE GATE LOCK ACTIVATION DEVICE
SUPPLEMENTARY RINGER
Output Input
Ref.9000/230
TRASFORMER
0 L C NA
HALL BUTTON FOR OPERATING GARAGE GATE LOCK
AP2
HALL BUTTON FOR OPERATING PEDESTRIAN ELECTRIC LOCK
AP1 SE1 SE2
MAIN~
MIKRA PANEL
ELECTRIC LOCK DOOR OPENER SENSOR
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
sec.5 −−−− 27
ONE-FAMILY AND TWO-FAMILY KITS
SUPPLEMENTARY RINGER
2-WIRE ONE FAMILY VIDEO KIT
2-WIRE ONE FAMILY VIDEO KIT
DEVICES - ACCESSORIES - SPARE PARTS TECHNICAL FEAUTURES - WIRE CROSS-SECTION AREA
2-WIRE ONE FAMILY VIDEO KIT
TECHNICAL FEAUTURES
The Urmet Video Kits can be used to make one-family video door phone systems without coax wire using only two wires to connect the video door phone to the video door unit.
VIDEO door PHONE (black and white version) Power supply: 26Vdc Kinescope: 4” Flat Resolution: 450 TV lines Ringer: electronic two-tone Dimensions: 218 x 220 x 80mm
The following versions of the Video Two one-family kits are available: • Black/white with zama vandal-proof panel Ref. 952/21 • Colour with zama vandal-proof panel Ref. 952/51
The panels are provided with 15 x 56 mm name tags.
Conversation between door unit and apartment unit can only be established after the apartment unit has been called. Call is two-tone electronic. The camera fits a high-sensitivity semipinhole camera. The subject is illuminated by LEDs. The video door phone has a door opener button and two special function buttons (auto-on, staircase lights, etc.). 2
2
VIDEO door PHONE (Colour version) Power supply: Kinescope: Resolution: Ringer: Dimensions: CAMERA UNIT (black and white version) Camera: Lighting: Power supply: Timer: Dimensions:
CCD 1/3” infrared LED 18Vdc approximately 90” 185 x 99 x 35mm
CAMERA UNIT (Colour version) Camera: Lighting: Power supply: Timer: Dimensions:
CCD 1/4” White LEDs 18Vdc approximately 90” 185 x 99 x 35mm
POWER SUPPLY Power supply: Power: Secondary unit: Protections: Dimensions: Weight:
2
System block chart Press the button on the panel: the call is sent to the monitor and the picture will appear after approximately 4 seconds. The call tone will last for approximately five seconds. Lift the handset to stop the call tone and speak with the video door phone. The monitor switch-on is timed (approximately 90 seconds). Any subsequent call or automatic switch-on will reset the timer.
110/230Vac ± 10% 50/60Hz 38VA 26Vdc 0.9 A (timed 20%) with PTC thermal switch (*) 96 x 126 x 75mm 1.1kg
(*) To restore the power supply if the PTC thermal switch trips following overload or short-circuit, power the unit down for 60 seconds or longer.
WIRE CROSS-SECTION AREA Distance Power supply/Videodoor phone mm Videodoor phone/Camera mm2
The basic product configuration is as follows: • One button camera unit. • Video door phone with bracket Atlantico style. • Power supply.
ONE-FAMILY AND TWO-FAMILY KITS
50m 100m 2
DEVICES
26Vdc 4” colour LCD 234 TV lines electronic two-tone 218 x 220 x 80mm
0,50 0,50
-0,75
The basic kit connections are not polarised.
ACCESSORIES The following accessories can be purchased separately: • Max 1 supplementary ringer Ref. 9854/41 or • Max 1 supplementary door phone Ref. 1133
SPARE PARTS The following spare parts are provided for repairs: • Power supply • Camera unit black and white colour • Bracket for Atlantico videodoor phone
28 −−−− sec.5
Ref. 952/100 Ref. 952/112 Ref. 952/113 Ref. 952/111
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
2-WIRE ONE FAMILY VIDEO KIT PANEL
PANEL
• Fasten the base onto a flat wall at the height shown in the figure using the bolts provided.
The camera unit is supplied complete with: • Semi pin-hole camera. • Led for lighting. • Front plate with 1 button. • Electronic circuit. • Lamp for lighting the name tags.
1,55 m ÷ 1,65 mm
Adjust volume (to be adjusted only when needed) and camera position.
installation
2-WIRE ONE FAMILY VIDEO KIT
35 mm
185 mm
99 mm
The panels with plastic casing may also be fixed in a flushmounting box Mod. 503 as shown below.
Mod. 503
• Remove the name tag light circuit.
• Insert the door unit into the compartment in the based and connect the wires (it is advisable to have approximately 40-45 mm of wire protruding from the wall).
ONE-FAMILY AND TWO-FAMILY KITS
ø 4 mm • Extract the door unit from the base.
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
sec.5 −−−− 29
2-WIRE ONE FAMILY VIDEO KIT PANEL
2-WIRE ONE FAMILY VIDEO KIT
• Fasten the name tag light circuit making the wires pass underneath the support.
CLI
• Insert the front part of the panel on the base and fasten it with the socket head screw using the wrench (2mm) provided.
CK
• Adjust volume and camera position. Volume is calibrated to optimal values during production. Change the settings when needed only. • Set the electrical lock operating time by shifting the jumper to the required position.
5°
5°
5°
10° = 1" default = 3" = 5" DOOR OPENER TIME PROGRAMMING
• Write the name on the name tag and insert in the housing.
ONE-FAMILY AND TWO-FAMILY KITS
Rossi
CLI iss
30 −−−− sec.5
CK
oR
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
2-WIRE ONE FAMILY VIDEO KIT VIDEO DOOR PHONE - POWER SUPPLY
VIDEO DOOR PHONE
1) Arrange the duct so that it ends in correspondence with one of the input holes. 2) Fasten the bracket to the wall at the height from the floor shown by means of the four screws. 3) Connect the wires to the specific terminals. 4) Check that switch on back of video door phone is in the A position. A B
This wall-mounted video door phone apartment station with next generation flat 4” kinescope screen does not need to be flush-mounted given the minimum protrusion from the wall. Installation is extreme simple and fast because the connections are shown on the terminal boards arranged on the bracket.
5) Extract the retainer hook A by inserting the tip of a screwdriver and pulling the hook downwards. 6) Fasten the monitor to the bracket as shown in the figure. 7) Fasten the monitor by pushing the retainer hook A upwards.
Bracket
The main characteristics of the video door phone are: • Adjustable and mutable call volume. The adjustment wheel appears red when the volume is muted.
2-WIRE ONE FAMILY VIDEO KIT
INSTALLATION
When volume is set to “MUTE” the video door phone will not ring but the video module will light up.
218 mm
1,55 m
• Door opener button is lit up and green when video module is on. • Service buttons ( and ) for activating, for example, supplementary electrical locks, staircase lights, video door phone auto-on function, etc. • Adjustable brightness and contrast. 80 mm
220 mm
A
POWER SUPPLY Ref. 952/100 Door opener button Call volume control and adjustment/ Mute function 75 mm
Brightness adjustment Auxiliary buttons
96
90
mm
mm
m
6m
12
The power supply unit provides power to the entire system. It is connected to the monitor by means of two wires. It can be wall-fitted or fitted on DIN bar. The power supply unit must be installed in dry places protected from weather conditions. 126mm in length correspond to seven 18mm modules, as per DIN 43880 standard.
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
sec.5 −−−− 31
ONE-FAMILY AND TWO-FAMILY KITS
Contrast/Colour adjustment
BASIC KIT CONNECTION
2-WIRE ONE FAMILY VIDEO KIT
SV102-3216 BASIC VIDEO DOOR PHONE + BRACKET
+26 R1
A A L L CA R1
~
AP 2 1 V3 AI +M
AP2 AP1 SE2 SE1 Lock opening
MAINS~
~
L
L
VIDEO POWER SUPPLY
TC VIDEO OUTDOOR STATION
ONE-FAMILY AND TWO-FAMILY KITS
Electrical Lock 12Vca 15VA
32 −−−− sec.5
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
A) Supplementary ringer Ref. 9854/41 Connection in parallel to 1 video door phone call B) Call repeater relay connection for controlling a supplementary ringer C) Connection of a secondary electrical lock
A)
BASIC VIDEO DOOR PHONE
A A L L CA R1
2-WIRE ONE FAMILY VIDEO KIT
SV102-3217B
FROM SYSTEM
AP 2 1 V3 AI +M
RINGER Ref.9854/41
B)
BASIC VIDEO DOOR PHONE
A A L L CA R1
FROM SYSTEM
AP 2 1 V3 AI +M RINGER S5 S4 S6
RELAY BOX Ref.788/52
C 6 CA 0~
12V~
S1 S2 S3 14 15
LINE~
~ ~ ~~ 12 0
TRANSFORMER Ref.9000/230
A A L L CA R1
BASIC VIDEO DOOR PHONE
FROM SYSTEM
Y1 Y2
12~ 2 S2 S3 S1
LINE~
~ ~ ~~ 12 0
TRANSFORMER Ref.9000/230
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
S5 S4 S6 C 6 CA 0~
RELAY BOX Ref.788/52
SECONDARY ELECTRIC LOCK
sec.5 −−−− 33
ONE-FAMILY AND TWO-FAMILY KITS
C)
ONE DOOR PHONE Ref. 1133 CONNECTION IN PARALLEL TO THE VIDEO DOOR PHONE ONE ATLANTICO VIDEO DOOR PHONE CONNECTION IN PARALLEL TO THE VIDEO DOOR PHONE SV102-3218 2-WIRE ONE FAMILY VIDEO KIT
A) BASIC VIDEO DOOR PHONE
A A L L CA R1
FROM SYSTEM
AP 2 1 V3 AI +M
DOOR PHONE Mod.Atlantico Ref.1133
1 2 9 6 10 CA
B) BASIC VIDEO DOOR PHONE
A A L L CA R1
FROM SYSTEM
AP 2 1 V3 AI +M
R=120 ohm 1/4W (VX.030)
Secondary VIDEO DOOR PHONE
R2 R1 R2 out in ~
ONE-FAMILY AND TWO-FAMILY KITS
1 2 9 6 CA X2 R1 R1 RD
POWER SUPPLY Ref.789/2
~
V4 V5V3
X1
LINE~
VX.030 max. distance between basic and secondary video door phone (terminals V3-V5): • normal wires 20m • coax cable 50m
34 −−−− sec.5
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
One and two-family Video Kit Mod. 956 with ARCO video door phone EQUIPMENT - Accessories - Spare parts TECHNICAL FEATURES - Wire sections
Block diagram for two family system
• • • • •
Ref. 1133/35A
Max 1 Atlantico door phone or Max 1 supplementary ringer Call repeater relay Transformer (230Vac 50Hz) Transformer (110Vac 60Hz)
Ref. 9854/41 Ref. 788/52 Ref. 9000/230 Ref. 9000/110
Spare parts The possible spare parts for repair are the following: • Camera • Panel with 1 button • Panel with 2 buttons • Power supply • Bracket for video door phone • Video door phone (CCIR Version 50Hz) • Video door phone (EIA Version 60Hz)
Ref. 956/123 Ref. 1729/1 Ref. 1729/2 Ref. 956/110 Ref. 1705/955 Ref. 1715/1 Ref. 1715/18
TECHNICAL FEATURES video door phone Power supply: Consumption: Kinescope: Resolution: Video input: Ringer: Dimensions:
By pressing a button of the push button panel the call is sent to the monitor on which the image appears after 4” about. By unhooking the handset, the conversation with the video outdoor station can take place. Monitor lighting is timed (one minute about). Every new call cancels the previous one with timer reset.
EQUIPMENT The products are the following: • One-family video door phone kit (230Vac 50Hz) Composed by: • Smyle Camera with 1 button • Arco video door phone with bracket • Power supply
Ref. 956/41
18Vdc max 600 mA max 4” Flat 450 TV lines 1Vpp differential electronic two-tone 206 x 230 x 70mm
CAMERA UNIT Camera: Lighting: Power supply: Timer: Video output: Dimensions:
CCD infrared LED 18Vdc max approximately 45” 1Vpp differential 185 x 99 x 35mm
POWER SUPPLY Power supply: 110/230Vac ± 10% 50/60Hz Power: 38VA Secondary unit: 12Vac 1A + 1A (timed 30%) 18Vdc 1A (timed 10%) Protections: with PTC thermal switch PTC (*) Dimensions: 96 x 126 x 75mm Dissipated power after 1 average working hour: 4,2W Length of 126 mm corresponds to seven 18 mm modules in accordance with DIN 43880 standards. 1,1Kg
Weight:
•
Two-family video door phone kit (230Vac 50Hz) Composed by: • Smyle Camera with 2 buttons • 2 Arco video door phones with bracket • Power supply
Ref. 956/42
•
One-family video door phone kit (110Vac 60Hz) Composed by: • Smyle Camera with 1 button • Arco video door phone with bracket • Power supply
Ref. 956/39
•
Two-family video door phone kit (110Vac 60Hz) Composed by: • Smyle Camera with 2 buttons • 2 Arco video door phones with bracket • Power supply
Ref. 956/49
One and two-family Video Kit Mod. 956 with ARTICO video door phone
Urmet video door phone system Mod. 956 allows single and two-user video systems without coax cable and with a reduced number of wires: 4 common wires + 1 calling wire for each monitor. The 4” monitor with flat screen does not need any embedding and, as for Urmet traditional video door phone system, the image appears only on the called monitor. The conversation between the outdoor station and the monitor can take place even if the indoor set has not been called. The call is electronic bitonal type; the TV camera unit uses a CCD TV camera; the subject is lighted by means of infrared Leds. The monitor is equipped with a door-release key and 2 additional keys that can be used for any service or as self-insertion key: in this case the system needs an additional wire in conduit.
Accessories
(*) To restore the power supply if the PTC thermal switch trips following overload or short-circuit, power the unit down for 60 seconds or longer.
Wire sections From tv camera unit to monitors Function Video power supply Video power supply Video signal
Wires
m
R1 R2 A
S/mm2 S/mm2 S/mm2
50m 100m 200m 0,5 0,5 0,35
0,75 0,75 0,35
B C1 - C2 AI
S/mm2 S/mm2 S/mm2
0,35 0,35 0,35
0,35 0,5 0,35
Video signal Call Self-insertion call
1,5 1,5 0,35
twisted
0,35 0,75 0,35
Distances are between the TV camera unit and the last monitor. DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
sec.5 −−−− 35
ONE-FAMILY AND TWO-FAMILY KITS
One and two-family Video Kit Mod. 956 with ARCO video door phone
One and two-family Video Kit Mod. 956 with ARTICO video door phone CAMERA UNIT
• Fasten the base onto a flat wall at the height shown in the figure using either the bolts provided or a 503 box.
From power supply to tv camera unit Wires
m
~12 ~0 +18 R1
S/mm2 S/mm2 S/mm2 S/mm2
Power supply 12V~ Power supply 12V~ Power supply 18Vdc Power supply 18Vdc
50m 100m 0,5 0,5 0,35 0,35
0,75 0,75 0,35 0,35 1,55 m ÷ 1,65 mm
Function
CAMERA UNIT 99 mm
35 mm
185 mm
One and two-family Video Kit Mod. 956 with ARTICO video door phone
Up to 100m it is possible to use normal wires; for longer distances, up to 200m, twist the wires A and B.
The camera unit is fitted in a Smyle panel. The unit includes: • Camera with solid state CCD sensor. • Infrared LED lights. • Front panel with 1 or 2 buttons. • Electronic circuits. • Name tag light LED. The internal and external sound volumes can be adjusted by operating on the proper controls.
Mod. 503
INSTALLATION • Remove the name tag light circuit.
ONE-FAMILY AND TWO-FAMILY KITS
• Insert the door unit into the compartment in the based and connect the wires (it is advisable to have approximately 40-45mm of wire protruding from the wall).
ø 4 mm • Extract the door unit from the base.
36 −−−− sec.5
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
One and two-family Video Kit Mod. 956 with ARTICO video door phone CAMERA UNIT - POWER SUPPLY
• Fasten the name tag light circuit making the wires pass under neath the support; then adjust volume and camera position.
• Insert the front part of the panel on the base and fasten it with the socket head screw using the wrench (2mm) provided.
5°
One and two-family Video Kit Mod. 956 with ARTICO video door phone
5°
5°
10°
CLI
CK
Volume is calibrated to optimal values during production. Change the settings when needed only.
• Write the name on the name tag and insert in the housing.
POWER SUPPLY Ref. 956/110
CLI iss
96
CK
90
mm
mm
m
6m
12
oR
The power supply unit provides power to the entire system. It is connected to the monitor by means of two wires. It can be wall-fitted or fitted on DIN bar. The power supply unit must be installed in dry places protected from weather conditions. 126mm in length correspond to seven 18mm modules, as per DIN 43880 standard.
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
sec.5 −−−− 37
ONE-FAMILY AND TWO-FAMILY KITS
75 mm
Rossi
One and two-family Video Kit Mod. 956 with ARCO video door phone VIDEOCITOFONO ARTICO
1. Arrange the cable conduits in order to match the holes for the cables passage. 2. With 4 screw anchors, fix the bracket to the wall at the height from the floor indicated. 3. Connect the wires to the suitable terminal pins. 4. Check that the switch on the rear side is set to A position. 4. Pull the stop hook α out. 5. Insert the video door phone in the bracket. 6. Lock the video door phone by pushing the hook α up
The main characteristics of the video door phone are the following: • Flat 4” video module. • Call volume adjustment and Mute function. When the Mute function is active, the visible part of the knob is red.
B
A
With the volume set to “MUTE”, the video door phone doesn’t emit any call ring tone, but the video module turns on.
• Button dedicated to door lock release service. • Service buttons ( e ). • Image brightness and contrast adjustment. 206 mm
70 mm
1
5
2
1,55 m
3
4 6
1 Call volume control and adjustment: with the selector set to down position (the visible part is red) the call ring tone is excluded (“MUTE” function)
MAX
ONE-FAMILY AND TWO-FAMILY KITS
INSTALLATION
230 mm
One and two-family Video Kit Mod. 956 with ARTICO video door phone
ARCO VIDEO DOOR PHONE
MED
α
MUTE
2 Door lock release button 3 Auxiliary button: used for special functions 4 Auxiliary button: used for special functions 5 Brightness adjustment control 6 Contrast adjustment control
38 −−−− sec.5
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
One family kit connection Ref. 956/31
One and two-family Video Kit Mod. 956 with ARTICO video door phone
SV102-2082C VIDEO DOOR PHONE (V5.011)
POWER SUPPLY
MAINS~
TC
VIDEO OUTDOOR STATION
ONE-FAMILY AND TWO-FAMILY KITS
4F
Lock release Electric lock 12Vca/15Va
V5.011 Connect the wire for Self-insert function. In this case make a jumper between terminals X2 and R3. DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
sec.5 −−−− 39
Two-family kit connection Ref. 956/32
One and two-family Video Kit Mod. 956 with ARTICO video door phone
SV102-2081B (V5.011)
1
VIDEO DOOR PHONE (V5.006) (V5.011)
2
POWER SUPPLY
MAINS~
ONE-FAMILY AND TWO-FAMILY KITS
TC
4F
VIDEO OUTDOOR STATION
Lock release Electric lock 12Vca/15Va
V5.006 The maximum distance between devices is 50 metres. V5.011 Connect the wire for Self-insert function. In this case make a jumper between terminals X2 and R3.
40 −−−− sec.5
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
Connection of 2 Artico video door phones in parallel
SV102-2135C One and two-family Video Kit Mod. 956 with ARTICO video door phone
MAINS~
POWER SUPPLY Ref.789/4 (V5.011)
1
VIDEO DOOR PHONE
(V5.006) (V5.011)
2
VIDEO DOOR PHONE
ONE-FAMILY AND TWO-FAMILY KITS
MAINS~
POWER SUPPLY TC
4F
VIDEO OUTDOOR STATION
Lock release
Electric lock 12Vca/15Va
V5.006 The maximum distance between devices is 50 metres. V5.011 Connect the wire for Self-insert function. In this case make a jumper between terminals X2 and R3. DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
sec.5 −−−− 41
Connection of 2 video door phones to 2 video door units Individual calls from video door unit
ONE-FAMILY AND TWO-FAMILY KITS
One and two-family Video Kit Mod. 956 with ARTICO video door phone
SV102-3225
1
RD CA X2 X1 A
VIDEO DOOR PHONE
B R1 R2 R3 (V5.006)
2
RD CA X2 X1 A
VIDEO DOOR PHONE
B R1 R2 R3
8
VIDEO OUTDOOR STATION TC
PS R1 R2 A B F 4 +18 R1 ~12 ~0 ~0 SE2 SE1
Electric lock 12Vca/15Va
C1
X (V5.013) C2 C1
SN1 7 1 4 10 11
52 C2
X (V5.013) C2 C1
SN2
PS R1 R2 A B F 4
9 3 6 12
VIDEO OUTDOOR STATION TC
(VX.021)
(VX.021)
+18 R1 ~12 ~0
LINE~ Lock release
14 13 15
+18 R1 ~12 ~0
~12 ~0
~
~
~
~
LINE~
Lock RELAY BOX release Ref.788/1 POWER SUPPLY TRANSFORMER or (VX.008) Ref.788/51 Ref.9000/230 or Ref.9000/110
~12 ~0 ~0 SE2 SE1
Electric lock 12Vca/15Va
(VX.008)
V5.006 The maximum distance between devices is 50 metres. V5.013 On device cut the wire connecting G/T terminal pin to printed circuit board. VX.021 Cut or remove the jumpers on the device: 4 and F.
42 −−−− sec.5
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
Connection of 1 door phone in parallel to 1 video door phone Simultaneous opening of 2 locks
(V5.011)
X1 X2 R3 VIDEO DOOR PHONE Mod.Artico
CA A B R2 R1
CA1 1
DOOR PHONE
2
~ ~12 ~0
MAINS~
S2 6 C
2 12~ CA ~0
S1
S3
C1 C2 AI
4F
VIDEO OUTDOOR STATION
Electric lock 12Vca/15Va
ONE-FAMILY AND TWO-FAMILY KITS
Lock release
RELAY BOX Ref.788/52
~
R1 R2 B A
SE2 ~0 R1 +18 ~12 ~0 SE1
TC
Electric lock 12Vca/15Va
TRANSFORMER 12V ~ 40VA
V5.011 Connect the wire for Self-insert function. In this case make a jumper between terminals X2 and R3. DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
One and two-family Video Kit Mod. 956 with ARTICO video door phone
SV102-2136E
sec.5 −−−− 43
Connection of supplementary ring Ref. 9854/41 in parallel to video door phone call Connection to call repeater relay for controlling a supplementary ringer
One and two-family Video Kit Mod. 956 with ARTICO video door phone
VIDEO DOOR PHONE Mod.Artico
ONE-FAMILY AND TWO-FAMILY KITS
SV102-2137D
Ringer 12V~
(V5.011)
RINGER Ref.9854/41
VIDEO DOOR PHONE Mod.Artico (V5.011)
RELAY BOX Ref.788/52
Line~ TRANSFORMER Ref.9000/230 or Ref.9000/110
V5.011 Connect the wire for Self-insert function. In this case make a jumper between terminals X2 and R3.
44 −−−− sec.5
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
