Transcript
INSTALLATION INSTRUCTIONS Rear Vision System – Tailgate Emblem Camera Mirror Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-9526) Kit Contents:
Tools Required:
Mirror 1 bubble bag containing: Mount with Camera Interior Harness 1 bag containing: Chassis Harness 1 bubble bag containing: Ford Emblem 1 bag containing 2 Tailgate emblem retainers 2 Mounting Screws 1 Foam piece (if needed and optional) 1 bag containing: 25 Wire Ties (short) Z-Tech (in a white bottle) 1 bag containing: 3 Templates (along with these instructions) 2 Wire Ties (long and optional)
T20 and T30 Torx Drivers 7mm, 8mm, and 10mm Sockets Flat Head Screwdriver Phillips Screwdriver Plastic Trim Removal tool Power Drill 1/8”, ¼”, 3/8” & 9/16” Drill Bits 1¾” Center Hole Saw Round File (if needed) Small Flat File (if needed) Soldering Iron (Recommended) Small Brush Mirror removal tool # OTC8200 (Required for non-screw type mirrors) Deburring Tool Small Grommet or Silicone Caulk (Recommended) Multimeter
NOTE: We strive to provide accurate and up-to-date installation instructions. For the latest full color instructions, as well as an installation video (use relevant portions of 1008-9520), please visit www.brandmotion.com
PRE-INSTALLATION VEHICLE CHECKLIST Before beginning, determine how the vehicle is equipped and check appropriate boxes: Determine whether the vehicle has an opening in the center of pickup bed close to opposite of the opening in the bottom of the tailgate. Yes, skip Section 2. No, tailgate must be removed to drill an opening for the Camera Harness (refer to Section 2). Determine whether the vehicle has the required three mounting holes behind the existing tailgate emblem. Refer to Steps 1 & 2 to remove inner tailgate panel, and use supplied 1008-9100-03 template to confirm whether the required holes are present in the panel. No, use supplied 1008-9100-03 template to position the holes to drill and/or cut the tailgate. If you do not wish to cut the tailgate, Brandmotion offers tailgate handle camera kits (1008-9520, black handle and 1008-9525, chrome handle) that do not require cutting. Yes, proceed to Section 3.
□
Vehicle does NOT have an auto dimming inside mirror (refer to Section 8).
Determine the connector style used on the existing inside rearview mirror: 7-pin or 16-pin. For past models additional information, please see Section 11B (Reference).
□ Check kit contents are complete against the list above.
9526 F series Instructions 7-31-12.doc
1 of 32
INSTALLATION INSTRUCTIONS
TABLE OF CONTENTS Pages Section 1: Camera Mount Preparation
3
Section 2: Drill Pickup Bed Opening (if required)
4
Section 3: Camera Installation
5
Section 4: Rain Sensor Modification (if equipped)
5
Section 5: Mirror Removal
6
Section 6: Interior Harness Installation Section 7: Interior Harness Wiring 7A: Remove compass circuit board (if required) 7B: Wiring for vehicles with 7-pin mirror connector 7C: Wiring for vehicles with 16-pin mirror connector 7D: Relocate compass circuit board (if required) Section 8: Wiring Required for Inside Mirrors without Auto Dimming (if required) Section 9: Supplied Mirror Installation Section 10: Chassis Harness Installation Section 11: Reference 11A: Supplied Harness Pinouts 11B: Previous Model Year Mirror Connector Pinouts 11C: Previous Model Year Ignition & Reverse Locations 11D: Relocating the Compass Circuit Board for vehicles with External Compass Module (if required) 11E: Vehicles with Sync Microphone in Mirror (if equipped) Safety Precautions: • Work in well ventilated area that is clear of obstructions. • Secure vehicle with tire chucks in both front and rear of tires. • Turn vehicle accessories OFF and ensure ignition key is in OFF position. • Wear safety goggles and snug fitting clothes. • Use tools only for their intended purpose and which are in good repair. • Only perform this task if confidence, skill, and physical ability permit.
9526 F series Instructions 7-31-12.doc
2 of 32
7-8 8 9 10 11 12-15 16 17-18 19 20-21 22-29 30-31 32
INSTALLATION INSTRUCTIONS Section 1: Camera Mount Preparation 1. Lower tailgate and remove upper sheet metal cover by removing the eight screws with a T30 Torx bit.
7. Drill the two retaining clip holes with a 3/8” drill bit. Use a small flat file to square the drilled holes for the retaining clips (recommended method). ALTERNATE METHOD: Drill the two holes with a 1/8” drill bit and use sheet metal screws (not supplied in kit) to mount the camera harness. Apply Z-tech to drilled holes.
2. From the inside of the tailgate, verify whether two square mounting holes and a central opening approximately 1-3/4” in diameter are present behind the factory emblem. If not, it will be necessary to drill and square two holes for camera mount retainers and a cut an opening for the camera and harness (Steps 5-7).
8. Insert supplied Retaining Clips.
3. Raise the tailgate. Taking care not to damage the body panel, insert plastic trim removal tool into the base of existing emblem to pry it off.
9. Drill a pilot hole for the Camera Mount. Using a 1¾” hole saw, cut the camera mount. Trial fit Camera Mount and file opening as necessary. 4. Remove any adhesive remaining on the tailgate. 5. If camera mounting holes and harness opening were present in the existing tailgate, proceed to Step 8. If not, align the supplied 1008-9100-03 template to the two existing emblem locating holes. 6. Mark and center punch the location for the two retaining clip holes and the camera and harness access opening.
10. Apply Z-tech to camera harness opening. 9526 F series Instructions 7-31-12.doc
3 of 32
INSTALLATION INSTRUCTIONS Section 2: Drill Pickup Bed Opening Follow Steps 11-18 only if the vehicle does NOT have an opening in the bed above the license plate per the below left picture
13. Center punch the mark and drill a ¼” hole.
11. Remove tailgate retaining straps. With an assistant, remove the tailgate by lifting away from lower tension pins. Set tailgate aside.
14. Clean the rough edges of the opening with a deburring tool. Apply supplied Z-tech with a small brush.
12. Measure 21 inches from the left edge and 1¼ inches from the top and make a temporary mark on the pickup bed.
15. With the aid of an assistant, reinstall tailgate on tension pins and reattach straps.
9526 F series Instructions 7-31-12.doc
4 of 32
INSTALLATION INSTRUCTIONS Section 3: Camera Installation 17. Run Camera Harness through opening in the base of the pickup bed.
16. Route the Camera Harness through tailgate opening. RECOMMENDED: Protect Camera Harness with a rubber grommet or by applying a small amount of silicone caulk to the area that comes into contact with the metal.)
18. Using the two supplied 7mm screws, attach Camera Mount to tailgate.
Section 4: Rain Sensor Modification (If equipped) Follow Steps 19 & 20 on this page only if a rain sensor module is mounted on your inside rear view mirror. 20. Using a round file, open up the rain sensor opening for mirror by 0.46mm so the supplied mirror fits.
19. Remove rain sensor by pulling down and remove connector.
9526 F series Instructions 7-31-12.doc
5 of 32
INSTALLATION INSTRUCTIONS Section 5: Mirror Removal 21. Start the vehicle and note location of compass display. Remove the connector from mirror.
CAUTION: Removing the mirror from the windshield can cause damage to the windshield. It is highly recommended to contact either a Ford dealership or a windshield replacement company. Otherwise, slide the mirror upwards and towards the rear to remove it from the windshield. 24. If the vehicle mirror is retained with a clip, use Mirror Removal Tool # OTC8200 available from Brandmotion.com or Ford dealers to release the mirror.
Mirror Removal Tool # OTC8200
22. If the compass display on the dash shows (- -) the compass module must be relocated. This operation is described in Section 7. 23. Determine the mirror mounting method. If clip method is used, proceed to Step 24. Otherwise, loosen the screw that attaches the existing rear view mirror to the windshield mounting button with a T20 Torx driver and proceed to Step 25.
9526 F series Instructions 7-31-12.doc
25. Slide the mirror upward to remove.
6 of 32
INSTALLATION INSTRUCTIONS Section 6: Interior Harness Installation 26. Remove driver side dash panel end cap by pulling away weather-stripping and pull end panel to release clips from the dash panel.
29. Remove roof console with hands to remove the clips from the sheet metal. Then remove both connectors.
30. Route the supplied Interior Harness under leading edge of the driver side headliner by gently separating the headliner from the windshield and tucking the harness into the gap with your fingers.
27. Remove driver side A-pillar by pulling with hands to release clips from sheet metal.
31. Route the supplied Interior Harness down the driver side A-pillar.
28. Remove both sun visor anchors (either side of roof console) by removing one screw with a Phillips screw driver.
9526 F series Instructions 7-31-12.doc
7 of 32
INSTALLATION INSTRUCTIONS Section 6: Interior Harness Installation continued 32. Route the supplied Interior Harness through the dash.
Section 7A: Removing the Compass Circuit Board (if required) Follow the steps in section 7A only if the vehicle compass displayed ‘- -‘ when the mirror connector was removed in Section 5. 35. Wrap the mirror circuit board in the supplied foam pieces, and cut an opening for the connector terminals.
33. Pry mirror apart with a screwdriver.
34. Remove the circuit board from the mirror by disengaging both connectors. Mark the top of the circuit board with a permanent marker to insure proper plug connection later.
9526 F series Instructions 7-31-12.doc
36. Make sure ignition is off. Remove the original vehicle mirror harness connector by cutting the harness wires 2 inches from the connector. Cut wires one at a time and strip the insulation from each as these will be spliced to the supplied Interior Harness.
8 of 32
INSTALLATION INSTRUCTIONS Section 7B: Wiring for vehicles with 7-pin mirror connector 37. On the supplied Interior Harness, near the black 16 pin connector, locate the seven loose wires. Using Connector C911 pinout diagram opposite, splice these wires to the vehicle mirror harness wires where the mirror connector was removed in Step 34 as follows: • Splice the supplied Interior Harness black ground wire to the loose vehicle mirror ground wire that was in pin 3. • Splice the supplied Interior Harness green reverse wire to the loose vehicle mirror reverse wire that was in pin 2. • Splice the supplied Interior Harness pink ignition wire to the loose vehicle mirror ignition wire that was in pin 1. • Splice the supplied Interior Harness red compass (+) to the loose vehicle mirror compass (+) wire that was in pin 6. • Splice the supplied Interior Harness yellow compass (-) to the loose vehicle mirror compass (-) wire that was in pin 7. • Splice the supplied Interior Harness orange auto dimming (+) wire to the loose vehicle mirror auto dimming (+) wire that was in pin 4. • Splice the supplied Interior Harness white auto dimming (-) wire to the loose vehicle mirror auto dimming (-) wire that was in pin 5.
NOTE: If reverse signal does not exist in pin 2 of 7-pin mirror C911 connector (see diagram below), then follow directions in Section 8 to connect reverse.
38. If you removed the compass circuit board, per section 7A, on the supplied Interior Harness, near the RCA connector end, locate the five loose wires. Using Connector C911 pinout diagram opposite, splice these five wires to the vehicle mirror harness connector removed in Step 34 as follows: • Splice the supplied Interior Harness black ground wire to the vehicle mirror connector ground wire. (pin 3) • Splice the supplied Interior Harness green reverse wire to the vehicle mirror connector reverse wire. (pin 2) • Splice the supplied Interior Harness pink ignition wire to the vehicle mirror connector ignition wire. (pin 1) • Splice the supplied Interior Harness red compass (+) wire to the vehicle mirror connector compass (+) wire. (pin 6) • Splice the supplied Interior Harness yellow compass (-) wire to the vehicle mirror connector wire. (pin 7) • If you did not remove the compass circuit board, isolate the five loose wires with electrical tape, as they will not be used. 9526 F series Instructions 7-31-12.doc
NOTE: Circuit colors shown may vary depending on model and year. Verify pin locations and check circuit for proper function using a digital volt-ohm meter.
9 of 32
INSTALLATION INSTRUCTIONS Section 7C: Wiring for vehicles with 16-pin connector 39. On the supplied Interior Harness, near the black 16 pin connector, locate the seven loose wires (Note: Isolate the red wire with electrical tape as it will not be used). Using Connector C9039 pinout diagram opposite, splice the remaining six wires to the vehicle mirror harness wires where the mirror connector was removed in Step 34 as follows: • Splice the supplied Interior Harness black ground wire to the loose vehicle mirror ground wire that was in pin 4. • Splice the supplied Interior Harness green reverse wire to the loose vehicle mirror reverse wire that was in pin 9. • Splice the supplied Interior Harness pink ignition wire to the loose vehicle mirror ignition wire that was in pin 1. • If populated, splice the supplied Interior Harness yellow wire to the loose vehicle mirror wire was in pin 2. • Splice the supplied Interior Harness orange auto dimming (+) wire to the loose vehicle mirror auto dimming (+) that was in pin 11. • Splice the supplied Interior Harness white auto dimming (-) wire to the loose vehicle mirror auto dimming (-) wire that was in pin 15.
NOTE: If reverse signal does not exist in Pin 9 of 16-pin mirror C9039 connector (see diagram opposite), then follow directions in Section 8 to connect reverse.
40. If you removed the compass circuit board, per section 7A, on the supplied Interior Harness, near the white 6 pin connector, locate the five short wires. (Note: Isolate the red wire with electrical tape as it will not be used). Using Connector C9039 pinout diagram opposite, splice the remaining four wires to the vehicle mirror harness connector removed in Step 34 as follows: • Splice the supplied Interior Harness black ground wire to the vehicle mirror connector ground wire. (pin 4). • Splice the supplied Interior Harness green reverse wire to the vehicle mirror connector reverse wire. (pin 9). • Splice the supplied Interior Harness pink ignition wire to the vehicle mirror connector ignition wire. (pin 1) • If populated, splice the supplied Interior Harness yellow wire to the vehicle mirror connector wire that supplies pin 2. • If you did not remove the compass circuit board, isolate the five loose wires with electrical tape, as they will not be used.
9526 F series Instructions 7-31-12.doc
10 of 32
NOTE: Circuit colors shown may vary depending on model and year. Verify pin locations and check circuit for proper function using a multimeter.
INSTALLATION INSTRUCTIONS Section 7D: Relocating the Compass Circuit Board (if required) Follow the steps in section 7D only if the vehicle compass displayed ‘- -‘ when the mirror connector was removed in Section 5. 41. Plug connector into mirror circuit board. Maintain the original connector orientation: retaining tab to top side of board.
44. Route the circuit board connector as shown
42. Remove driver’s side knee bolster trim by removing three screws with a M7 socket. Pull panel by hand to release mounting clips.
45. Place the mirror circuit board as shown (connector facing forward and towards the bottom). Secure the circuit board to the existing cross dash harness with the two supplied Long Wire Ties.
43. Remove the driver’s side knee bolster reinforcement by removing the four M8 screws.
9526 F series Instructions 7-31-12.doc
11 of 32
INSTALLATION INSTRUCTIONS Section 8: Inside Rear View Mirrors without Auto Dimming (if required) Follow the steps in section 8 only if the vehicle does not have an auto dimming inside rear view mirror. 46. Remove the passenger side door sill plate with a trim tool and remove passenger side kick panel with hands, just disengaging the two clips from the sheet metal.
49. Splice the green reverse wire from the supplied Interior Harness RCA connector end to the wire listed in Diagram A below, depending on the vehicle model. Solder and cover the connection with electrical tape or heat shrink tubing. 50. Attach the black ground wire eyelet from the supplied Interior Harness RCA connector end to sheet metal in the passenger side kick panel with a screw using an 8mm socket.
47. Isolate the seven wires near the black 16-pin mirror connector on the supplied Interior Harness with electrical tape along with the red and yellow wires near the RCA connector end. 48. Route the supplied Interior Harness green, pink, and black wires along the vehicle cross dash harness as shown in the picture opposite. Secure using wire ties wherever possible at 2 inch intervals.
51. Splice the pink ignition wire from the supplied Interior Harness RCA connector end to the wire listed in Diagram A below, depending on the vehicle model. Solder and cover the connection with electrical tape or heat shrink tubing.
Non Auto Dimming Pinouts Diagram A Chassis Harness Ignition & Reverse Locations Model
F150
Super Duty
Year(s)
Function
Connector
Diagram Page
2012
Ignition
C2280B
13
Reverse
C2280D
14
Ignition
C2280B
15
Reverse
C2280D
14
(late production)
2012 (late production)
NOTE: For previous years pinouts, please refer to Section 11C.
9526 F series Instructions 7-31-12.doc
12 of 32
Location Right Kick (BCM) Right Kick (BCM) Right Kick (BCM) Right Kick (BCM)
Supplied Interior Harness Color
Pin
Color
35
Violet/Green
Pink
13
Blue/White
Green
35
Violet/Green(Gas) Yellow/Orange (Diesel)
Pink
13
Blue/White
Green
INSTALLATION INSTRUCTIONS Section 8: Inside Rear View Mirrors without Auto Dimming continued (if required) INSIDE REAR VIEW MIRROR WITHOUT AUTO DIMMING DIAGRAM B Ignition Connector C2280B – 2012 late production F150
9526 F series Instructions 7-31-12.doc
13 of 32
INSTALLATION INSTRUCTIONS Section 8: Inside Rear View Mirrors without Auto Dimming continued (if required) INSIDE REAR VIEW MIRROR WITHOUT AUTO DIMMING DIAGRAM C Reverse Connector C2280D – 2012 late production F150 and Super Duty
9526 F series Instructions 7-31-12.doc
14 of 32
INSTALLATION INSTRUCTIONS Section 8: Inside Rear View Mirrors without Auto Dimming continued (if required) INSIDE REAR VIEW MIRROR WITHOUT AUTO DIMMING DIAGRAM D Ignition Connector C2280B – 2012 late production Super Duty
9526 F series Instructions 7-31-12.doc
15 of 32
INSTALLATION INSTRUCTIONS Section 9: Supplied Mirror Installation 52. Plug the 16-pin connector from the supplied Interior Harness into the supplied mirror.
53. Install the supplied mirror on the mounting button and slide it downwards. Secure by tightening the T20 Torx screw to 1.8 Nm (16 lb-in.), while not exceeding 2.2 Nm (19.5 lb-in.). 54. If equipped, reinstall modified Rain Sensor from Section 4.
9526 F series Instructions 7-31-12.doc
16 of 32
INSTALLATION INSTRUCTIONS Section 10: Chassis Harness Installation 55. Remove the driver side sill plate with a trim tool.
56. Loosen driver side A-pillar molding with hands and then remove the driver side lower kick panel.
59. Center punch and drill a pilot hole then drill a 9/16” hole for the Chassis Harness to pass through.
57. Pull back carpet in front of driver’s seat.
60. Clean the hole with a deburring tool and apply supplied Z-tech with a small brush.
58. Secure Super Duty template number 1008-9100-01 or F150 template number 1008-9100-02 over opening in front of driver’s seat.
9526 F series Instructions 7-31-12.doc
17 of 32
INSTALLATION INSTRUCTIONS Section 10: Chassis Harness Installation continued 61. Route the supplied Chassis Harness through the drilled opening. RECOMMENDED: Add a small grommet or small amount of silicone caulk to protect the harness from the metal edges.
64. Loop any excess from the harness as shown and secure with tie wraps.
62. Route the supplied Chassis Harness toward the supplied Interior Harness and connect together.
65. Plug the Chassis Harness into the Camera Harness installed earlier under the pickup bed.
63. Route the exterior portion of the supplied Chassis Harness along existing vehicle chassis harness and over fuel tank. Using supplied tie wraps, secure the harness to existing wiring at 2 inch intervals.
66. Start vehicle with foot on brake and shift into reverse to check camera operation. If all of the connections are correct, you will see an image displayed on the left side of the supplied Mirror. 67. Press supplied Ford Emblem into Camera Mount. 68. Reinstall all previously removed interior and exterior parts.
9526 F series Instructions 7-31-12.doc
18 of 32
INSTALLATION INSTRUCTIONS Section 11A: Reference – Supplied Harness Pinouts Loose Wires Provided in the Supplied Interior Harness at the 16-pin Connector Function Ground (-) Reverse signal 12V Ignition 12V Compass (+) Compass (-) Auto dimming (+) Auto dimming (-)
Wire color Black Green Pink Red Yellow Orange White
16-pin connector pinout PIN 1 2 3 4 5 6 7 8
White dot identifies cavity 1
9 10 11 12 13 14 15 16
9526 F series Instructions 7-31-12.doc
19 of 32
Circuit Description Not Used Not Used Camera Video Shield Camera Power (+) Dual Outside Drive EC (+) Camera NTSC Video (+) Camera NTSC Video (-) Vehicle Ground (-) Reverse Input (Active High) Camera Power (-) Not Used Not Used Ignition (Run Only Line) Not Used Not Used Dual Outside Drive EC (-)
INSTALLATION INSTRUCTIONS Section 11B: Reference - Previous Model Year Mirror Connector Pinouts
Supplied Interior Harness Color 1 Pink
Microphone Supplied Harness Color 1 Blue (+)
2 Green
2
3 Black
3 Black
4 5 6
4 5 6 Yellow
7
7
8
8
9 Red
9
10 Yellow
10
11 12 13
11 12 13
14
14 Black
15 16
15 16
Supplied Interior Harness Color 1 Pink 2 3 4 Black 5 6 7 8 9 Green 10 11 Orange (+) 12 13 14 15 White (-) 16
9526 F series Instructions 7-31-12.doc
20 of 32
INSTALLATION INSTRUCTIONS Section 11B: Reference - Previous Model Year Mirror Connector Pinouts continued 2004-2007 F150 Pinout
9526 F series Instructions 7-31-12.doc
21 of 32
INSTALLATION INSTRUCTIONS Section 11C: Reference - Previous Model Year Ignition & Reverse Locations
Model
F150
F150
F150
Super Duty Super Duty
Supplied Interior Harness Color
Connector
Diagram Page
Location
Pin
Color
Ignition
C270J
23
Right Kick
2
White / L. Blue
Pink
Reverse
C270E
24
Right Kick
20
Black / Pink
Green
Ignition
C270J
23
Right Kick
2
White / L. Blue
Pink
Reverse
C270B
25
Right Kick
12
Green/ Yellow
Green
20092012
Ignition
C2280D
26
Right Kick
16
Blue or Blue/ Red
Pink
(early production)
Reverse
C215
27
Right Kick
6
Blue
Ignition
C264
28
Right Kick SJB
10
Red / Yellow
Pink
Reverse
C264
28
Right Kick SJB
12
Black / Pink
Green
20092012
Ignition
C264
29
Right Kick
2
Blue
(early production)
Reverse
C264
29
Right Kick
10
Green/ Blue
Year
Function
2004
20052008
2008
9526 F series Instructions 7-31-12.doc
22 of 32
Green
Pink Green
INSTALLATION INSTRUCTIONS Section 11C: Reference – Previous Model Year Ignition & Reverse Locations continued Ignition Connector C270J – 2004 – 2008 F-150
9526 F series Instructions 7-31-12.doc
23 of 32
INSTALLATION INSTRUCTIONS Section 11C: Reference – Previous Model Year Ignition & Reverse Locations continued Reverse Connector C270E – 2004 F150
9526 F series Instructions 7-31-12.doc
24 of 32
INSTALLATION INSTRUCTIONS Section 11C: Reference – Previous Model Year Ignition & Reverse Locations continued Reverse Connector C270B – 2005-2008 F150
9526 F series Instructions 7-31-12.doc
25 of 32
INSTALLATION INSTRUCTIONS Section 11C: Reference – Previous Model Year Ignition & Reverse Locations continued Ignition Connector C2280D – 2009-2012 (early production) F150
9526 F series Instructions 7-31-12.doc
26 of 32
INSTALLATION INSTRUCTIONS Section 11C: Reference – Previous Model Year Ignition & Reverse Locations continued Reverse Connector C215 – 2009-2012 (early production) F150
9526 F series Instructions 7-31-12.doc
27 of 32
INSTALLATION INSTRUCTIONS Section 11C: Reference – Previous Model Year Ignition & Reverse Locations continued Ignition and Reverse Connector C264 – 2008 Super Duty
9526 F series Instructions 7-31-12.doc
28 of 32
INSTALLATION INSTRUCTIONS Section 11C: Reference – Previous Model Year Ignition & Reverse Locations continued Ignition and Reverse Connector C264 – 2009-2012 (early production) Super Duty
9526 F series Instructions 7-31-12.doc
29 of 32
INSTALLATION INSTRUCTIONS Section 11D: Reference –
Relocating the Compass Circuit Board for vehicles with External Compass Module (if required) 69. Remove the separate compass module from the existing interior mirror by sliding it downwards.
70. Remove connector from the compass module.
9526 F series Instructions 7-31-12.doc
71. Pry the compass apart with a screwdriver.
72. Remove the circuit board from the compass module.
30 of 32
INSTALLATION INSTRUCTIONS Section 11D: Reference –
Relocating the Compass Circuit Board for vehicles with External Compass Module continued (if required) 73. Wrap the circuit board in the supplied foam and cut an opening for connector terminal.
74. Plug the compass module connector into the circuit board.
. 75. Install the compass module circuit board between underneath the headliner as shown. The connector should face up, to the rear, and to the right.
9526 F series Instructions 7-31-12.doc
31 of 32
INSTALLATION INSTRUCTIONS Section 11E: Reference – Vehicles with Sync Microphone in Mirror
Follow the steps on this page only for auto dimming inside rear view mirror with built in Sync microphone. 74. Connect the supplied Interior Harness to the vehicle mirror harness by making the following 10 splices while referring to Diagram E. NOTE: Isolate the black, green and pink wires at the RCA connector end of the supplied Interior Harness with electrical tape as they will not be used. • Splice the black ground wire from the supplied Interior Harness black 16 pin connector end to the wire in pin 10 of the vehicle mirror harness connector. • Splice the green reverse wire from the supplied Interior Harness black 16 pin connector end to the wire in pin 3 of the vehicle mirror harness connector. • Splice the pink ignition wire from the supplied Interior Harness black 16 pin connector end to the wire in pin 1 of the vehicle mirror harness connector. • Splice the orange positive (+) auto dimming wire from the supplied Interior Harness black 16 pin connector end to the wire in pin 8 of the vehicle mirror harness connector. • Splice the white negative (-) auto dimming wire from the supplied Interior Harness black 16 pin connector end to the wire in pin 7 of the vehicle mirror harness connector. • Splice the red positive (+) compass wire from the supplied Interior Harness black 16 pin connector end to the wire in pin 6 of the vehicle mirror harness connector. • Splice the yellow negative (-) compass wire from the supplied Interior Harness black 16 pin connector end to the wire in pin 2 of the vehicle mirror harness connector. • Splice the yellow open wire from the microphone harness (supplied separately) to the wire in pin 4 of the vehicle mirror harness connector. • Splice the black ground wire from the microphone harness (supplied separately) to the wires in pins 5 and 10 of the vehicle mirror harness connector. • Splice the blue 12V positive (+) wire from the microphone harness (supplied separately) to the wire in pin 1 of the vehicle mirror harness. • Cover all connections with electrical tape or heat shrink. 75. Place the microphone in a convenient place on A-pillar or in headliner.
Auto Dimming With Built In Sync Microphone Mirror Pinout DIAGRAM E Supplied Interior Harness Wire Color
Microphone Supplied Harness Wire Color
1 Pink
1 Blue +
2 Yellow
2
3 Green
3
4
4 Yellow -
5
5 Black
6 Red
6
7 White -
7
8 Orange +
8
9
9 10 Black
10 Black
9526 F series Instructions 7-31-12.doc
32 of 32
