Transcript
TRACTOR - MODEL NO. PB20H42YT (96042012403), PRODUCT NO. 960 42 01-24
SCHEMATIC SCH11
BATTERY RED
SOLENOID
M
FUSE
AMMETER (OPTIONAL)
BLACK
WHITE
S B G
STARTER
RED
A
WHITE
M A1
L
A2
ATTACHMENT CLUTCH (CLUTCH OFF) BLACK
CLUTCH/BRAKE (PEDAL UP)
GRAY
REVERSE SWITCH (NOT IN REVERSE)
BLACK BLACK
BLACK
2
BLACK
3
BLACK BLACK
SEAT SWITCH (NOT OCCUPIED)
BLACK BLACK
1 6
GRAY
SHORTING CONNECTOR
CHASSIS HARNESS
IGNITION UNIT
(OPTIONAL)
SPARK PLUGS GAP (2 PLUGS ON TWIN CYL. ENGINES)
HOUR METER
BLUE
BLACK
NOTE YOUR TRACTOR IS EQUIPPED WITH A SPECIAL ALTERNATOR SYSTEM. THE LIGHTS ARE NOT CONNECTED TO THE BATTERY, BUT HAVE THEIR OWN ELECTRICAL SOURCE. BECAUSE OF THIS, THE BRIGHTNESS OF THE LIGHTS WILL CHANGE WITH ENGINE SPEED. AT IDLE THE LIGHTS WILL DIM. AS THE ENGINE IS SPEEDED UP, THE LIGHTS WILL BECOME THEIR BRIGHTEST.
BLACK /WHITE
JUNCTION CONNECTOR
BLACK
FUEL LINE
12V POWER OUTLET (OPTIONAL)
BLUE
FUEL SHUT-OFF SOLENOID (IF SO EQUIPPED)
CHARGING SYSTEM OUTPUT 3 AMP DC @ 3600 RPM
28 VOLTS AC MIN. @ 3600 RPM (CHARGING SYSTEM DISCONNECTED)
RED
LIGHTING SYSTEM OUTPUT 5 AMP AC @ 3600 RPM DIODE
ALTERNATOR
ORANGE
LIGHT SWITCH
14 VOLTS AC MIN. @ 3600 RPM (LIGHTS OFF) BROWN
BLACK
HEADLIGHTS
IGNITION SWITCH POSITION
CIRCUIT
OFF RUN/OVERRIDE
M+G+A1 B+A1
RUN START
B+A1 B + S + A1
“MAKE”
L+A2
3
6
6
3
2
5
5
2
1
4
4
1
CHASSIS HARNESS CONNECTOR (MATING SIDE)
DASH HARNESS CONNECTOR (MATING SIDE)
3
WIRING INSULATED CLIPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE RE-INSTALLED TO PROPERLY SECURE YOUR WIRING.
NON-REMOVABLE CONNECTIONS
REMOVABLE CONNECTIONS
TRACTOR - MODEL NO. PB20H42YT (96042012403), PRODUCT NO. 960 42 01-24
ELECTRICAL T01S
90
22
27
2
33 30
79
21
1
87
91 99 100
24
8 34
27 43 42 41
40
26 55
28
25
16
71
With 12V Outlet Option
103
59
94 With Service Minder Option 29
92
46
93
4
TRACTOR - MODEL NO. PB20H42YT (96042012403), PRODUCT NO. 960 42 01-24
ELECTRICAL
KEY NO. 1 2 8 16 21 22 24 25 26 27 28 29 30 33 34 40 41 42 43 46 55 71 79 87 90 91 92 93 94 99 100
PART NO. 532 16 34-65 874 76 04-12 532 18 64-91 532 17 61-38 532 18 37-59 532 00 41-52 532 40 02-53 532 41 28-94 532 17 51-58 873 51 04-00 532 14 54-91 532 40 15-45 532 19 33-50 532 41 19-33 532 11 07-12 532 40 10-98 817 72 04-08 532 13 15-63 532 19 25-07 532 40 17-63 817 06 05-12 532 19 42-76 532 17 52-42 532 19 78-02 532 43 53-95 532 19 02-70 532 19 66-15 532 19 25-40 532 19 18-34 817 67 04-12 819 09 14-16
DESCRIPTION Battery Bolt Hex Head 1/4-20 x 3/4 Box Battery Switch Interlock Push-In Harness Socket Light w/4152J Bulb Light Cable Battery Cable Starter Fuse Nut Keps Hex 1/4-20 unc Cable, Ground Switch, Seat Switch, Ignition Key/Chain Switch Light/Reset Harness Ignition Dash Screw Thd Cut 1/4-20 x 1/2 Cover, Terminal Solenoid Gauge SRVCMNDR HRMTR Screw Thdrol 5/16-18 x 3/4 TYTT Harness Ignition Socket Asm Bulb Twistlock Switch Interlock Clutch Cable Cover Terminal Battery Strap Battery Harness Pigtail Console ROS Screw Plastite 10-14 x 2.0 Module Reverse ROS Screw 1/4-20 x 3/4 Washer 9/32 x 7/8 x 16 Ga.
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
5
TRACTOR - MODEL NO. PB20H42YT (96042012403), PRODUCT NO. 960 42 01-24
CHASSIS
15 297 18
25
14
191
206
130
5 137 176
205
176 176
177
151
175
289
176
176
130 150
182 196
36
161
181
194
235
36
236 68
194 68
235 236
138 139 278
34
68
287
68
183 181
162
37
139
68
165 228
152
68
194 189
159 228
189 180 chassis-tex_elite sv tv husq_10
159
6
TRACTOR - MODEL NO. PB20H42YT (96042012403), PRODUCT NO. 960 42 01-24
CHASSIS
KEY NO. 5 14 15 18 25 34 36 37 68 130 137 138 139 150 151 152 159 161 162 165 175 176 177 180 181 182 183 189 191 194 196 205 206 228 235 236 278 287 289 297
PART NO.
532 43 27-79 532 43 63-82 532 18 99-82 532 43 27-78 532 18 99-81 532 19 61-25 817 06 05-12 532 44 05-11 817 49 05-08 532 41 63-58 532 18 49-21 532 40 97-30 532 17 18-73 532 43 16-32 532 40 78-07 532 19 95-35 817 00 06-12 532 41 20-72 532 14 24-32 532 19 68-26 532 19 32-43 532 40 07-76 532 19 52-27 532 19 54-57 532 40 47-96 532 19 30-57 874 52 05-20 817 00 05-12 532 41 65-00 873 90 05-00 532 41 45-79 532 42 47-47 532 42 47-48 532 19 51-61 532 40 61-29 873 93 05-00 532 19 63-94 817 60 04-06 532 43 27-81 532 18 82-67
DESCRIPTION
Dash Upper Tex Elite El Ck 428 Hood Pnt Elite Spl-Tp W-Skirts Lens Elite-Husq Clear LH Grille Asm Elite Dl BLK Lens Elite-Husq Clear RH Plate Engine Welded Chassis Screw 5/16-18 X 3/4 Smgml Tap/R Fender Tlt W/Cph W/Fw 421 Screw Thdrol 5/16-18 X 1/2Tytt Screw Bumper Hood Large 1 75" Cupholder Tl Tex 428 Bolt Shoulder 5/16-18 Air Duct Bracket Pivot Lasr/Elte/Husqlt Shield Browning W/Tex Screw Hexwsh 3/8-16 X 3/4 Window Fuel Screw Hex Wsh Hi-Lo 1/4 X 1/2 Unc Support Tank Rear Crossmember Lt Screw #10-24X5/8 Rnd Qudrx Gim Bushing Steering Yt/Gt Chass Wldmt Tl 12 Ga/2Pc Bushing Mnt Fend Crgo Blk Tex Dash Lower Lt Ccs Bolt 5/16-18 X 1-1/4 Screw 5/16-18 X 3/4 Smgml Tap/Bl Insert Reflective RH Nut, Lock Hex Flange 5/16-18 Unc Console Asm Decklft Bl/Rbt Tlt Skirt Side Rh Elite Husq 428 Skirt Side Lh Elite Husq 428 Stud Fastner W/'D'anti-Rotatio Spacer Fender Nut Center Lock 5/16-18 Unc Bracket Hood Screw Hex Washead 1/4-20 X 3/8 Plug Cruise Hook Phone Insert Lens Rflct Elt-Husq
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
7
TRACTOR - MODEL NO. PB20H42YT (96042012403), PRODUCT NO. 960 42 01-24
DRIVE
70
56
74
216
143
171 221 184 35
125 80 125 125 227
42 64
167
159
170
160
52 226
29 159
51 188
15
49
211
185 186
279
161
189 17
166
153
175
50
178
51 125
52
51
225 22
33
116
183
166
2 205
230
116 2
99
drive-tex_K46_fender_24_r1
73
1 73
183
8
230
174 233
23
187
190
176
205
33
232
TRACTOR - MODEL NO. PB20H42YT (96042012403), PRODUCT NO. 960 42 01-24
DRIVE
KEY NO.
PART NO.
1
– – – – – –
2 15 17 22 23 29 33 35 42 49 50 51 52 56 64 70 73 74 80 99 116 125 143 153 159 160 161
532 12 35-83 819 13 13-16 532 41 36-78 532 19 76-60 532 14 08-45 532 40 38-06 812 00 00-01 532 19 77-22 532 12 48-72 872 11 06-14 532 19 43-27 873 90 06-00 532 19 43-26 532 13 09-69 532 19 62-00 532 41 13-29 874 49 05-40 532 14 24-32 532 44 06-19 532 41 57-42 873 90 05-00 817 00 05-12 817 49 05-08 532 12 47-88 876 02 04-12 532 16 94-84 532 10 57-09
DESCRIPTION Transaxle, Tufftorq K46 BA (408214)(Order parts from transaxle manufacturer) Key Square Washer 13/32 x 13/16 x 16 Ga. Spring, Brake Rod Shift Knob Rod, Brake Ring E Rod, Brake, Park Cover, Foot Pedal Bolt Pulley Idler Flat Lock Nut 3/8-16 Idler V-Groove V-Belt, Drive Shaft Asm. Pedal Brake Control Console Bolt 5/16-18 x 2 1/2 Gr. 5 Screw 1/4 x 1/2 Strap Torque Rod Asm Bypass Nut Lock Hex Flange 5/16-18 Screw 5/16-18 x 3/4 Screw 5/16-18 x 1/2 Retainer Spring Pin Cotter 1/8 x 3/4 Retainer Clip Spring, Return, Clutch
KEY NO.
PART NO.
DESCRIPTION
166 167 170 171 174 175 176 178 183 184 185 186 187 188 189 190 205 211 216 221 225 226 227 230 232 233 279
532 42 91-64 532 40 52-57 532 19 43-22 872 11 06-16 532 19 72-89 532 40 62-08 532 19 62-14 532 19 74-56 532 13 70-57 532 44 15-04 872 11 06-22 532 19 43-21 819 13 32-10 532 19 43-23 532 19 43-17 532 19 43-18 532 12 17-48 532 19 62-12 532 19 61-31 532 40 31-87 532 40 33-19 532 40 15-64 817 49 05-12 532 18 89-67 874 78 07-16 532 40 52-96 532 40 62-07
Nut Push .625 Latch Brake Parking Keeper Belt Centerspan Bolt Rdhd Sqnk 3/8-16 x 2 Nut Push Shaft Asm Shift Arm Clevis Rod Shift Spring Shift Spacer, Axle Handle Parking Brake Bolt Spacer Retainer Washer Link Clutch Ground Drive Bellcrank Ground Drive Keeper Bellcrank Ground Drive Washer 25/32 x 1-5/8 x 16 Ga. Bushing Brake Shaft Bracket Pulley Idler Retainer Spring Clip Handle Keeper Belt Trans. Bracket Mount Torque Screw Thdrol 5/16-18 x 3/4 Washer Hardened Bolt 7/16-14 x 1 Gr. 5 Washer Serrated Link Shift
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
9
TRACTOR - MODEL NO. PB20H42YT (96042012403), PRODUCT NO. 960 42 01-24
ENGINE
1 21
87 20 62
69 45
18 84
84
71 15
12
70 82
37
81
79
42
28
85 37 90
9
29
SPARK ARRESTER KIT engine-tex_bs-2cyl_73
10
2
TRACTOR - MODEL NO. PB20H42YT (96042012403), PRODUCT NO. 960 42 01-24
ENGINE
KEY PART NO. NO. 1 – – – – – – 2 9 12 15 18 20 21 28 29 37 42 45 62 69 70 71 79 81 82 84 85 87 90
532 14 97-23 532 19 43-20 532 40 54-71 532 43 80-80 532 43 02-14 532 42 35-02 532 41 63-58 532 40 11-35 532 13 71-80 532 12 34-87 810 04 07-00 873 51 04-00 532 43 40-17 532 16 53-91 532 15 99-55 532 16 05-89 532 18 39-06 532 14 84-56 532 42 82-87 817 06 06-20 532 17 39-37 532 17 18-77 817 00 06-16
DESCRIPTION Engine B&S Model No. 406777-0442-B1 (428039) (Order parts from engine manufacturer) Muffler Keeper Belt Engine Pulley Engine Tank Fuel Cap Fuel Control Throttle/Choke Screw #10 x 0.750 BOS Thread Fuel Line Spark Arrester Kit Clamp Hose Washer Lock 7/16 Nut Keps Hex 1/4-20 unc Shield Heat Muffler Gasket Exhaust Tube LH Exhaust Tube RH Screw Socket HD 5/16-18 x 1 Tube Drain Oil Easy Valve Drain Oil Screw 3/8-16 x 1-1/4 Bolt 7/16-20 x 4 x Gr. 5-1.5 Bolt 5/16-18 unc x 3/4 Screw 3/8-16 x 1
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm For engine service and replacement parts, call the toll free number for your engine manufacturer listed below: Briggs & Stratton 1-800-233-3723
Engine Power Rating Information The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and corrected in accordance with SAE J1995 (Revision 2002-05). Torque values are derived at 3060 RPM; horsepower values are derived at 3600 RPM. Actual gross engine power will be lower and is affected by, among other things, ambient operating conditions and engine-to-engine variability. Given both the wide array of products on which engines are placed and the variety of environmental issues applicable to operating the equipment, the gas engine will not develop the rated gross power when used in a given piece of power equipment (actual “on-site” or net power). This difference is due to a variety of factors including, but not limited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this Series engine.
11
TRACTOR - MODEL NO. PB20H42YT (96042012403), PRODUCT NO. 960 42 01-24
STEERING ASSEMBLY
26
45 51
1
20 21
57
63 19
57
16
63
60
66
9
61 8
7
67 2
59
98 7
6 64
4
35 58
67
28 13
15
6
14
22
5 62
69
14 15
68
53 8 13
70
13
steering-tex_STDSRR_1_r2
12
TRACTOR - MODEL NO. PB20H42YT (96042012403), PRODUCT NO. 960 42 01-24
STEERING ASSEMBLY
KEY NO.
PART NO.
DESCRIPTION
1 2 4 5 6 7 8 9 13 14 15 16 19 20 21 22 26 28 35 45 51 53 57 58 59 60 61 62 63 64 66 67 68 69 70
532 42 45-51 532 19 59-68 532 40 30-87 532 40 30-88 532 12 49-31 532 12 17-48 812 00 00-29 532 12 12-32 532 12 17-49 810 04 06-00 873 54 06-00 532 40 82-19 532 19 47-29 532 43 27-84 532 18 67-37 532 42 05-37 532 42 45-53 817 00 06-12 532 19 47-32 819 18 38-12 873 94 08-00 532 18 89-67 532 40 74-65 532 19 47-47 532 19 47-48 873 97 10-00 532 19 47-40 532 19 47-41 817 00 05-12 532 19 98-49 871 02 07-48 532 19 47-37 873 90 07-00 532 19 91-62 532 19 61-97
Wheel, Steering Axle Asm., Front Spindle Asm., LH Spindle Asm., RH Bearing, Race Thrust Harden Washer 25/32 x 1-5/8 x 16 Ga. Ring, Clip #T5304-75 Cap, Spindle Washer 25/32 x 1-1/4 x 16 Ga. Washer, Lock Hvy Hlcl Spr 3/8 Nut, Crown Lock 3/8-24 unf Shaft Steering Plate Steering Boot, Steering Adapter, Wheel Steering Steering Support Lower Insert, Wheel Steering Screw 3/8-16 x 3/4 Gear, Sector Plate Washer 9/16 ID x 2-3/8 x 12 Ga. Nut Hex Jam Toplock 1/2-20 unf Washer Hardened .793 x 1.637 x .060 Bracket Upstop Bolt Shoulder Sector Pivot CFM Washer Thrust Sector Steering Nut Flange Lock 5/8-11 Draglink, LH Draglink, RH Screw 5/16-18 x 3/4 Retainer Clip Spring Steering Bolt Hex Fghd 7/16-14 x 3 Serr Bushing PM Front Axle Nut Lock Flange 7/16-14 Gr. 5 Washer 1.5 x .505 x .118 Bracket Deck Susp. Front
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
13
TRACTOR - MODEL NO. PB20H42YT (96042012403), PRODUCT NO. 960 42 01-24
MOWER DECK
70
195
67
122
7 152
195 40
57 145
43 30
59
42 56
60
55
57 56
38
46 63 147
64 113
116
40
117
30 38
36 47
33
34
192
32
144 241 242
119
116
123
68
7
37
31
40
113 111 21
30 1
119
119 117
2 117
40
21 62
116
21
118 11
23
69
188
24
189 6
21
25
113
19
26 189
6
188
29 15
19 14
20 69
13
27 69
21 11
112
2 8 42_D_man-tex_LT_33_r6
118 119 113
14
117 116
TRACTOR - MODEL NO. PB20H42YT (96042012403), PRODUCT NO. 960 42 01-24
MOWER DECK
KEY NO.
PART NO.
1 2 6 7 8 11
532 19 64-95 872 14 05-06 532 19 51-86 532 41 63-58 532 19 30-03 532 13 89-71
13 14 15 19 20 21 23 24 25 26 27 29 30 31 32 33 34 36 37 38 40 42 43 46 47 55 56 57 59
532 19 28-72 532 18 72-81 532 11 04-85 532 19 65-39 532 15 97-70 873 68 05-00 532 19 25-57 532 10 53-04 532 19 70-26 532 11 04-52 532 40 30-04 532 13 14-91 532 17 39-84 532 18 76-90 532 19 74-73 532 40 02-34 872 11 06-12 532 19 73-79 819 13 13-16 532 43 25-20 873 90 06-00 532 19 84-10 532 19 72-56 532 13 77-29 532 19 72-50 532 43 71-10 532 19 90-92 817 00 06-16 532 14 10-43
DESCRIPTION Mower Housing Bolt Rdhd 5/16-18 x 3/4 Arm Suspension Screw #10 x 0.750 BOS Thread Bolt/Washer Asm 7/16-20 unf Blade, 42" Hi-Lift (For bagging or discharge) Shaft Assembly, Mandrel Housing, Mandrel Bearing, Ball, Mandrel Bolt, Shoulder Baffle, Vortex Nut, Crownlock 5/16-18 unc Bracket, Deflector Cap, Sleeve Spring, Torsion, Deflector Nut, Push Shield, Deflector Rod, Hinge Screw Thdrol Rolling Wsh Hd Washer, Spacer Pulley, Mandrel Nut, Toplock, Flanged Bolt Carr Sh. 3/8-16 x 1-1/2 Gr. 5 Pulley, Idler 4.50 RAW Washer 13/32 x 13/16 x 16 Ga. Keeper Belt Mandrel Nut, Lock Flg. 3/8-16 unc Spring Torsion Brake Spring Torsion Retainer Screw Thd Roll 1/4-20 x 5/8 Bracket Clutch Cable Arm, Idler Spacer, Retainer Screw Hexwsh Thd 3/8-16 x 1 Guard, Tuv Idler (94)
KEY NO. 60 62 63 64 67 68 69 70 111 112 113 116 117 119 122 123 144 145 147 152 188 189 192 195 241 242 --
PART NO. 532 19 72-61 872 11 06-16 532 19 94-77 532 19 97-90 532 40 30-12 532 42 96-36 872 14 05-05 532 19 97-79 532 40 47-84 532 40 47-85 817 00 05-10 532 12 48-42 532 18 86-06 819 12 14-14 532 19 72-58 532 19 72-59 532 19 92-04 532 19 31-97 532 40 19-71 532 43 51-11 532 19 51-61 873 90 05-00 532 19 72-60 817 00 06-12 532 15 29-27 532 41 55-98 532 19 28-70
--
532 40 30-66
DESCRIPTION Arm Brake Mower Bolt Rdhd Sqnk 3/8-16 unc x 2 Arm Brake Mower Linkage Brake Handle, Clutch Cable V-Belt Bolt Rdhd Sqnk 5/16-18 x 5/8 Clutch Asm. Manual Bracket Wheel Gauge LH Bracket Wheel Gauge RH Screw 5/16-18 Bolt Shoulder "A" 2.41 "B" 1.66 Wheel Gage Washer 3/8 x 7/8 x 14 Ga. Keeper Belt Eng. LH Keeper Belt Eng. RH Keeper Belt Pulley Idler Primary Spring Return Cable Clutch Manual w/Spr. Stud Fastener Nut Lock Hex Flange Bracket Brake Stand LH Screw Hexwsh Thdr 3/8-16 x 3/4 Screw #10-32.5 3/8 Flange Port Washout Mandrel Assembly (Includes housing, shaft assembly, and bearing only - pulley/nut/washer and blade bolt/washers not included) Replacement Mower, Complete
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
15
TRACTOR - MODEL NO. PB20H42YT (96042012403), PRODUCT NO. 960 42 01-24
MOWER LIFT
87
7
90
98
89
10 3 97
100 2
88
97
91
101 87
89 89
87
lift-tex_29
KEY NO.
PART NO.
DESCRIPTION
2 3 7 10 87 88 89 90 91
532 42 20-27 532 19 52-31 532 41 15-55 532 19 63-14 532 19 42-09 532 41 07-10 819 19 19-12 532 19 42-08 532 19 51-81
Shaft Asm., Lift Lever Asm., Lift RH Grip, Lever Spring Torsion Pin Cotter 7/16 Bow Tie Lock Spring Lift Assist Washer Clear Zinc Pin Cotter 5/16 Bow Tie Lock Link Asm. Lift Rear
KEY NO.
PART NO.
DESCRIPTION
97 98 100 101
817 00 06-12 532 19 52-70 873 93 06-00 532 40 70-03
Screw 3/8-16 x .75 Smgml Tap/R.Z Link Lift Susp. Front Mower Nut Centerlock 3/8-16 unc Link Asm. Lift Fixed
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
16
TRACTOR - MODEL NO. PB20H42YT (96042012403), PRODUCT NO. 960 42 01-24
SEAT ASSEMBLY
8 8
1
8 8 7
7
41 40
10
21
6
37 37 2
44 43
21
3 seat-tex_6.5SL_1_r1
KEY NO.
PART NO.
DESCRIPTION
1 2 3 6 7 8 10 21
532 40 66-23 532 18 01-66 532 14 06-75 873 80 06-00 532 12 41-81 532 17 18-77 532 19 69-77 532 17 18-52
Seat Bracket Pivot Fender Strap, Asm Fender Nut, Lock w/Ins. 3/8-16 unc Spring, Seat Cprsn Bolt 5/16-18 unc x 3/4 w/Sems Pan, Seat Bolt, Shoulder 5/16-18
KEY NO.
PART NO.
DESCRIPTION
37 40 41 43 44
873 80 05-00 532 19 76-61 532 19 82-00 874 76 06-12 819 13 38-12
Nut, Lock 5/16-18 unc Handle Slide Seat Spring Latch Seat Bolt Fin Hex 3/8-16 unc x 3/4 Washer 13/32 x 2-3/8 x 12 Ga.
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
17
TRACTOR - MODEL NO. PB20H42YT (96042012403), PRODUCT NO. 960 42 01-24
DECALS
1 1
11
13 4
6
3
9
10
10
2
5
14
KEY NO. 1 2 3 4 5 6 9 10 11
PART NO. 532 44 52-35 532 17 05-63 532 44 52-30 532 44 52-34 532 42 95-61 532 41 16-57 532 14 50-05 532 43 84-92 532 43 84-31
DESCRIPTION Decal, Hood RH/LH Decal, Keep Hand Away Decal, Side Panel Decal, Fender Decal, Eng H.P. Decal, Fender Operator's Decal, Battery Dnge/Poi Decal, Fender SD RH/LH Decal, Replacement
WHEELS AND TIRES 1 2
11 3 7
4
10 5
6
9 8
KEY NO. 13 14 -----
PART NO. 532 43 85-01 532 16 03-96 532 41 12-73 532 40 95-05 532 16 69-60 532 44 42-53
--
532 44 51-39
KEY NO. 1 2 3 4 5 6 7 8 9 10 11 --
PART NO. DESCRIPTION 532 05 91-92 Cap, Valve, Tire 532 06 51-39 Stem, Valve 532 43 96-73 Rim Assembly, Front 532 05 99-04 Tube, Front 532 10 62-22 Tire, Front 532 12 49-57 Fitting, Grease 532 12 49-59 Bearing, Flange 532 17 50-39 Cap, Axle (Front Wheel Only) 532 13 84-68 Tire, Rear 18 x 9.5-8 Turf Saver 532 12 49-26 Tube, Rear 532 44 08-81 Rim Assembly, Rear 532 14 43-34 Sealant, Tire (10 oz. Tube)
DESCRIPTION Decal, Steering Wheel Decal, Mower Schematic Pad, Footrest RH Pad, Footrest, LH Decal, Bypass Manual, Operator's (English/Spanish) Manual, Parts (English/Spanish)
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
wheel_art_1-vgt
18
