A0230026_oslo-sq Led Ww Product Sheet

Transcript

LED technology THE ART OF LIGHTING 79 Φ: 79 32 , OSLO-SQ LED WW 0.?? 350mA 39.9Lm 3000K Mountingdepth in mm 64 32 20 0.13 Ordernr: A0230026 Lamptype: Wall lamp 1.05W warm-white LED Vf: 3V Light direction: down/direct Housing: solid Aluminium (Cu 0.1, Mn 0.1, Fe 0.35, Mg 0.62, Zn 0.1, Si 0.4) Weight: 0.13 Kg Dimensions fixture: Ø79 x 32 mm Classification: IP-20 (indoor rated) class III Operating Power: constant current 350mA Excluded (external) LED-driver Always disconnect the mains of the LED driver before plugging or unplugging the LED`s !! The LED`s will be damaged or destroyed because of the high voltage present on the driver output when there is no load connected. Connect the main after all Led`s and plugs are connected ! Attention !! Load minimal 1 LED fixture incl.0.5mtr cable & plug Optional external LED-drivers: 350mA on dimable LED-drivers: A9950001 LSVC3A (Load: min.1W / max: 3W) A9950002 LSVC4A (Load: min.1W / max: 4W) A9950003 LSVC8A (Load: min.1W / max: 8W) A9950004 LSVC18A (Load: min.1W / max: 18W) Non Dimmable serial connection plugs always must be connected !! 35.13° PRI A9950001 LSVC3A 1-3W Vf: 3-9V LED Driver 100-240V AC Dimmable LED driver: A9950010 Universal Driver Jolly (Load: min.1W / max: 15W @ 350mA) SEC + - Load: max. 2x Oslo-R @ LED-driver LSVC4A. fIXTURES serial connection(max total sec. cable length ???mtr) 0.63m / 1m 69.9 Lx 52.4 Lx Non Dimmable 1.26m / 2m 17.5 Lx 13.9 Lx serial connection plugs always must be connected !! 100-240V AC + - 1.90m / 3m 7.77 Lx 5.82 Lx PRI 2.53m / 4m 4.37 Lx 3.27 Lx SEC A9950002 LSVC4A 1-4W LED Driver Vf: 3-14V Load: max. 3x Oslo-R @ LED-driver LSVC4A. fIXTURES serial connection(max total sec. cable length ???mtr) Diam.(m)/ Distance Dimensions in mm 79 Attentiion !! Load minimal 1 LED fixture Non Dimmable PRI 100-240V AC - LED Driver Emax(Lux) Emed(Lux) serial connection plugs always must be connected !! SEC + 79 ø 60 Load: max. 7x Oslo-R @ LED-driver LSVC8A. fIXTURES serial connection(max total sec. cable length ???mtr) A9920500 3AP (optional) LED 3-way serial connection box with 1 mtr cable 32 LED Fixture connection Mounting : ø 64mm (21/2“) 20 INDOOR RATED Fixture fits in wallbox Attema U50 without using screws Only remove the serial-plugs for connecting a LED Fixture Wall Lights Non Dimmable by LED-driver LTVC18A ordernr: A9950004 Always disconnect the mains of the LED driver before plugging or unplugging the LED`s !! The LED`s will be damaged or destroyed because of the high voltage present on the driver output when there is no load connected. Connect the main after all Led`s and plugs are connected ! + SEC serial connection plugs always must be connected !! - 100-240V AC LED Driver PRI Load: max. 14x Oslo-SQ @ LED-driver LTVC18A. fIXTURES serial connection(max total sec. cable length ???mtr) Dimmable -+ by Universal Driver ordernr: A9950010 Jolly Push button (Pulse switch) function By pressing the push button for less than one second the LEDs turn on or off. By pressing the push button for more than one second the light intensity of the LEDs is dimmed according to the following modalities: • If the light intensity is not at maximum, by pressing the key there will be an increase of this to maximum or to the corresponding level at the moment the key is released. • A further pressure on the key inverts the dimming direction to the minimum value or to the corresponding level at the moment the key is released. • If light intensity is at maximum by pressing the key there will be a decrease to the minimum value or to the corresponding level at the moment the key is released. Sync conection to next LED driver Connection with pulse-switch for max. 10 LED drivers Function synchronization during dimming of more than one ballast is possible by means of the sync gates. In this way there is the same light intensity (with the same connected led load) among all the connected ballasts. This possibility is highly recommended when more than one ballast needs to be controlled by one push button (see the diagram). Dipswitch setting for Oslo-R Max load for Oslo-R is 350mA Switch 1-6 must be set: OFF N.B.: The use of the push button inhibits the use of the 1...10 V signal. To return to use of the 1...10 V signal keep the signal less than 0,5 V for at least 2 seconds. Dip-switch no: SEC 15W 350mA 22W 500mA 25W 9W 700mA 10W 20W 12V 24V 1 3 2 4 6 ON ON ON ON ON ON ON ON ON ON ON Max output power and current precision @ 220÷240 Vac: 15 W @ 350 mA ± 6% (2...43 V); • Efficiency @ full load: 0,89%, DIM 50% = 0,87%; • No load consumption: 1,2 W. ON 10V ON ON ON ON + + + + - SYNC SEC - 1-10V serial connection plugs always must be connected !! Dipswitch for selection of output current (see dipswitch setting) - LED Driver A9915010 5 1 2 3 4 5 6 max.Load Cable clambs max. 2.5mm² PUSH L PRI N L A9950010 @350mA: 1-15W Vf: 2-43V Load: max. 15x Oslo-R @ Universal Dimmable LED-drive A9915010 Fixtures serial connection(max total sec. cable length ???mtr) 100-240V AC + + + + SEC 1-10V - SYNC - LED Driver A9915010 serial connection plugs always must be connected !! Dipswitch for selection of output current (see dipswitch setting) - ON 1 2 3 4 5 6 Dipswitch setting for Oslo-R Max load for Oslo-R is 350mA Switch 1-6 must be set: OFF Cable clambs max. 2.5mm² PUSH L PRI N L 100-240V AC Load: max. 15x Oslo-R @ Universal Dimmable LED-drive A9915010 Fixtures serial connection(max total sec. cable length ???mtr) N L Max. 10 drivers can be controlled by one push button Max cable length from push button to last driver must be max. 15m !! Use normally open push button with no incorporated warning light pulse switch • Short push to turn ON and OFF • Push and hold to increase or decrease light intensity