Transcript
LED technology THE ART OF LIGHTING A9950010 LED dimmable driver universal max 25W Multi-power driver with dip-switch for output-selection (constant direct current or constant direct voltage) Dimmable 1-10V & Push dim Prim.Voltage: 110V~240V 50~60Hz\ 21 Max input current: 0.16A 103 Power factor l: =0.95 93,5 Sec.: 350-700mA 10/12/24V (see dip-switch setting) ta °C: -20° +50° tc °C: 75° Protection against overheating, short ciquit & overloads 57,5 67 Dimension L x W x H (mm): 103 x 67 x 21 Weight: 0.11 Kg Protection: IP-20 Class II
Dip-switch setting for direct constant current output-selection Micro-switch setting
SEC: 350mA 500mA 550mA 700mA 750mA
6
5
4
Input Voltage: 220..240VAC
2
3
_ _ _ _ ON _ _ ON _ _ ON ON _ ON ON
_ _ _ _ _
_ _ _ _ _
1
_ _ _ _ _
Input Voltage: 110..127VAC ta max.
Max load:
Vf:
Max load:
Vf:
15W +/-6%
2..43V
15W +/-6%
2..43V
50°
22W +/-5% 22W +/-5% 25W +/-5%
2..43V
2..30V
50°
2..43V
15W +/-5% 15W +/-5%
2..30V
50°
2..36V
15W +/-5%
2..21V
50°
25W +/-5%
2..34V
15W +/-5%
2..21V
50°
Optional: A9920500 3AP LED 3-way serial connection box A9920501 6AP LED 6-way serial connection box A9920515 1,5m extension cable male/female A9920530 3m extension cable male/female
1W)
350mA max. load: 15W 500mA max. load: 22W 700mA max. load: 25W
Connection LED fixtures: serial (min. load:
1W)
350mA max. load: 15W 500mA max. load: 22W 700mA max. load: 25W
Connection LED fixtures: serial (min. load:
1W)
350mA max. load: 15W 500mA max. load: 22W 700mA max. load: 25W
Dipswitch for selection of output current (see dipswitch setting) Cable clambs max. 2.5mm²
+
+ +
-
SYNC
Connection LED fixtures: serial (min. load:
-
SEC
-
LED Driver A9915010
+
ON
1 2 3 4 5 6
Constant Current connection with dimmer
1-10V
PUSH L PRI N L
100-240V AC Dimmer: 100k Log
Cable clambs max. 2.5mm²
+
+ +
-
SYNC
Dipswitch for selection of output current (see dipswitch setting) -
SEC
-
LED Driver A9915010
+
ON
1 2 3 4 5 6
Constant Current connection with control voltage function
1-10V
PUSH L PRI N L
1-10V 0
100-240V AC
External device control voltage
+
+
1-10V
Cable clambs max. 2.5mm²
+ +
SEC
-
SYNC
-
LED Driver A9915010
Dipswitch for selection of output current (see dipswitch setting) -
ON
1 2 3 4 5 6
Constant Current connection with push dimming function
Max cable length: 15m
PUSH L PRI N L
L
N pulse switch
100-240V AC Short push to turn ON and OFF Push and hold to increase or decrease light intensity
Always disconnect the mains of the LED driver before plugging or unplugging the LED`s !! The LED`s will be damaged or destroyed because of the high voltage present on the driver output when there is no load connected. Connect the main after all Led`s and plugs are connected !
Accessoiries
LED technology THE ART OF LIGHTING
+
+ +
-
SEC 1-10V
-
SYNC
Dipswitch for selection of output current (see dipswitch setting)
-
LED Driver A9950010
+
ON
1 2 3 4 5 6
Connection with potentiometer for max. 10 LED drivers
PUSH L PRI N L
Dip-switch setting for direct constant current output-selection Micro-switch setting
SEC:
100-240V AC
350mA 500mA 550mA 700mA
Dipswitch for selection of output current (see dipswitch setting)
+
+
_ _ _ _ ON _ _ ON _ _ ON ON _ ON ON
+ +
SEC 1-10V
4
-
SYNC
-
LED Driver A9950010
5
-
ON
1 2 3 4 5 6
750mA
6
PUSH L PRI N L
100-240V AC
Max. 10 drivers can be controlled by one potentiometer Max cable length from potentiometer to last driver must be max. 15m !
1 LED driver: 2 LED drivers: 4 LED drivers: 10 LED drivers:
use 100k logaritmic potentiometer use 47-50k logaritmic potentiometer use 25k logaritmic potentiometer use 10k logaritmic potentiometer
Accessoiries
3
_ _ _ _ _
Input Voltage: 220..240VAC
2
_ _ _ _ _
1
_ _ _ _ _
Input Voltage: 110..127VAC ta max.
Max load:
Vf:
Max load:
Vf:
15W +/-6%
2..43V
15W +/-6%
2..43V
50°
22W +/-5% 22W +/-5% 25W +/-5%
2..43V
2..30V
50°
2..43V
15W +/-5% 15W +/-5%
2..30V
50°
2..36V
15W +/-5%
2..21V
50°
25W +/-5%
2..34V
15W +/-5%
2..21V
50°
LED technology THE ART OF LIGHTING
Connection with pulse-switch for max. 10 LED drivers
Push button (Pulse switch) function
Dip-switch setting for direct constant current output-selection Micro-switch setting
SEC: 350mA 500mA 550mA 700mA 750mA
6
5
4
_ _ _ _ ON _ _ ON _ _ ON ON _ ON ON
3
_ _ _ _ _
Input Voltage: 110..127VAC
Input Voltage: 220..240VAC
1
2
_ _ _ _ _
_ _ _ _ _
ta max.
Max load:
Vf:
Max load:
Vf:
15W +/-6%
2..43V
15W +/-6%
2..43V
50°
22W +/-5% 22W +/-5% 25W +/-5%
2..43V
2..30V
50°
2..43V
15W +/-5% 15W +/-5%
2..30V
50°
2..36V
15W +/-5%
2..21V
50°
25W +/-5%
2..34V
15W +/-5%
2..21V
50°
Dip-switch setting for direct constant voltage output-selection Input Voltage: 110..127V
Micro-switch setting
Input Voltage: 220..240V
Max load:
ta max.
Max load:
[email protected] +/-7% (900mA max.)
[email protected] +/-7% (900mA max.)
[email protected] +/-5% (900mA max.)
[email protected] +/-5% (900mA max.)
[email protected] +/-5% (620mA max.)
[email protected] +/-5% (900mA max.)
6
4
3
50°
_
5
ON
50°
ON
ON ON ON
ON
50°
ON ON ON
Max output power and current precision @ 220÷240 Vac: 15 W @ 350 mA ± 6% (2...43 V); 22 W @ 500 mA ± 5% (2…43 V); 25 W @ 700 mA ± 5% (2…36 V); • Max. Output voltage: 48 VDC; • Possibility of switch on the LED on secondary side; • Efficiency @ full load: 0,89%, DIM 50% = 0,87%; • No load consumption: 1,2 W.
_ _
2
_ ON
_
_ _ ON
-
By pressing the push button for less than one second the LEDs turn on or off. By pressing the push button for more than one second the light intensity of the LEDs is dimmed according to the following modalities: • If the light intensity is not at maximum, by pressing the key there will be an increase of this to maximum or to the corresponding level at the moment the key is released. • A further pressure on the key inverts the dimming direction to the minimum value or to the corresponding level at the moment the key is released. • If light intensity is at maximum by pressing the key there will be a decrease to the minimum value or to the corresponding level at the moment the key is released. Function synchronization during dimming of more than one ballast is possible by means of the sync gates. In this way there is the same light intensity (with the same connected led load) among all the connected ballasts. This possibility is highly recommended when more than one ballast needs to be controlled by one push button (see the diagram). N.B.: 1. The use of the push button inhibits the use of the 1...10 V signal. To return to use of the 1...10 V signal keep the signal less than 0,5 V for at least 2 seconds. 2. To reset the driver, press and hold the push button 3-4 seconds, release the button and press immediatly the push button shortly once.
+
Sync conection to next LED driver A9950017 Sync conection-cable length 1.5mtr
1 2 3 4 5 6
ON
+
+
+ +
-
SYNC
-
SEC
-
LED Driver A9950010
Dipswitch for selection of output current (see dipswitch setting)
1-10V
Cable clambs max. 2.5mm²
PUSH L PRI N L
Dipswitch for selection of output current (see dipswitch setting)
+
+ +
-
SEC 1-10V
-
SYNC
A9950017 Sync conection-cable length 1.5mtr
-
LED Driver A9950010
+
ON
1 2 3 4 5 6
100-240V AC
Cable clambs max. 2.5mm²
max cable length 5m (up to 1.5mm)
PUSH L PRI N L
L
N
100-240V AC
pulse switch • Short push to turn ON and OFF • Push and hold to increase or decrease light intensity
Accessoiries
LED technology THE ART OF LIGHTING
A9950010 LED dimmable driver universal max 25W Multi-power driver with dip-switch for output-selection (constant direct current or constant direct voltage) Dimmable 1-10V, 100K potentiometer or Pusch button
Dip-switch setting for direct constant voltage output-selection Input Voltage: 110..127V
Micro-switch setting
Input Voltage: 220..240V
Max load:
ta max.
Max load:
[email protected] +/-7% (900mA max.)
[email protected] +/-7% (900mA max.)
[email protected] +/-5% (900mA max.)
[email protected] +/-5% (900mA max.)
[email protected] +/-5% (620mA max.)
[email protected] +/-5% (900mA max.)
6
4
3
50°
_
5
ON
50°
ON
ON ON ON
ON
50°
ON ON ON
_ _
2
_ ON
_
_ _ ON
+
LED Fixture(s) Constant Voltage Parallel connected max. Load: 10W @ 12V 20W @ 24V
+ +
-
SYNC
Dipswitch for selection of output current (see dipswitch setting) -
SEC
-
LED Driver A9950010
+
ON
1 2 3 4 5 6
Constant Voltage connection with dimmer
1-10V
PUSH L PRI N L
Cable clambs max. 2.5mm² 100-240V AC Dimmer: 100k Log
+
LED Fixture(s) Constant Voltage Parallel connected max. Load: 10W @ 12V 20W @ 24V
+ +
-
SYNC
Dipswitch for selection of output current (see dipswitch setting) -
SEC
-
LED Driver A9950010
+
ON
1 2 3 4 5 6
Constant Voltage connection with control voltage function
1-10V
PUSH L PRI N L
Cable clambs max. 2.5mm²
1-10V 0
100-240V AC
External device control voltage
+
+
+ +
-
SEC 1-10V
Dipswitch for selection of output current (see dipswitch setting)
-
LED Driver A9950010
SYNC
-
ON
1 2 3 4 5 6
Constant Voltage connection with push pull dimming function
LED Fixture(s) Constant Voltage Parallel connected max. Load: 10W @ 12V 20W @ 24V
Max cable length: 15m
PUSH L PRI N L
Cable clambs max. 2.5mm²
Pulse-switch 100-240V AC
Short push to turn ON and OFF Push and hold to increase or decrease light intensity
Always disconnect the mains of the LED driver before plugging or unplugging the LED`s !! The LED`s will be damaged or destroyed because of the high voltage present on the driver output when there is no load connected. Connect the main after all Led`s and plugs are connected !
Accessoiries
