Aapx55hm0xdl40

Transcript

10.3Gb/s XFP Transceiver Connects fiber to your home AAPX55HM0xDL40 ATOP Corporation 10.3Gb/s XFP Transceiver APX55HM0xDL40  Product Features  Supports 9.95 to 11.3Gb/s  Duplex LC connector  Hot-pluggable XFP footprint  Cooled 1550nm EML laser  RoHS compliant and Lead Free  40Km link length  Metal enclosure for lower EMI  Built-in dual CDR  +5.0V and +3.3V power supply and power dissipation <2.5W   Applications  SONET OC-192 IR-2/IR-3 SDH STM S-64.2b/S-64.3b XFP MSA INF-8077I Compliant ITU-T G.709  10GBASE-ER/EW 10GBASE-ER/EW + FEC  10G Fibre Channel 10G Fibre Channel + FEC  General ATOP’s APX55HM0xDL40 Small Form Factor 10Gb/s XFP transceivers are compatible with XFP MSA Specification. They comply with SONET OC-192 IR-2,OC-192 IR-3,SDH STM S-64.2b,STM S-64.3b as well as with 10G Ethernet 10G BASE-ER/EW per IEEE802.3ae and 40km 10G Fibre Channel applications.  Product Selection Part Number Operating Case temperature DDMI APX55HM0CDL40 Commercial(0~70℃) Yes APX55HM0EDL40 Extend(0~85℃) Yes APX55HM0IDL40 Industrial(-40~85℃) Yes www.atoptechnology.com Rev1.0 2016-07 Page 1 10.3Gb/s XFP Transceiver Connects fiber to your home AAPX55HM0xDL40 ATOP Corporation  Regulatory Compliance  ESD to the Electrical PINs: compatible with MIL-STD-883 Method 3015  ESD to the Duplex LC Receptacle: compatible with IEC 61000-4-2  Immunity compatible with IEC 61000-4-3  EMI compatible with FCC Part 15 Class B EN55022 Class B (CISPR 22B) VCCI Class B  Laser Eye Safety compatible with FDA 21CFR 1040.10 and 1040.11 EN60950, EN (IEC) 60825-1,2  ROHS compliant with ROHS 2 (2011/65/EU)  Pin Descriptions Pin Symbol Name/Description 1 GND Module Ground 2 VEE5 Optional -5.2 Power Supply – Not required MOD_DESE Module De-select; When held low allows the module to L respond to 2-wire serial interface. LVTTL-I /INTERRUP Interrupt; Indicates presence of an important condition which T can be read via the 2-wire serial interface. LVTTL-O Ref. 3 4 2 Transmitter Disable. Logic1 indicates laser output disabled, 5 TX_DIS LVTTL-I 6 VCC5 +5V Power Supply 7 GND Module Ground 8 VCC3 +3.3V Power Supply 9 VCC3 +3.3V Power Supply 10 SCL 2-Wire Serial Interface Clock. LVTTL-I 2 11 SDA 2-Wire Serial Interface Data Line. LVTTL-I/O 2 12 MOD_Abs 1 Indicates Module is not present. Grounded in the Module. 2 LVTTL-O Module Not Ready; Indicating Module Operational Fault. 13 MOD_NR 2 Open-collector. LVTTL-O 14 RX_LOS www.atoptechnology.com Loss of Signal indication. Logic 1 indicates loss of Signal. Rev1.0 2016-07 2 Page 2 10.3Gb/s XFP Transceiver Connects fiber to your home AAPX55HM0xDL40 ATOP Corporation Open-collector. LVTTL-O 15 GND Module Ground 1 16 GND Module Ground 1 17 RD- Receiver Inverted Data Output. CML-O 18 RD+ Receiver Non-Inverted Data Output. CML-O 19 GND Module Ground 1 20 VCC2 +1.8V Power Supply (Not required). 3 Power down; When high, requires the module to limit power consumption to 1.5W or below. 2-Wire serial interface must be P_DOWN/R functional in the low power mode. LVTTL-I ST Reset; The falling edge initiates a complete reset of the 21 module including the 2-wire serial interface, equivalent to a power cycle. LVTTL-I 22 VCC2 +1.8V Power Supply (Not required) 3 23 GND Module Ground 24 REFCLK+ Reference Clock (Not required) 25 REFCLK- Reference Clock (Not required) 26 GND Module Ground 1 27 GND Module Ground 1 28 TD- Transmitter Inverted Data Input. CML-I 29 TD+ Transmitter Non-Inverted Data Input. CML-I 30 GND Module Ground 1 1 Notes: 1. Module ground pins GND are isolated from the module case and chassis ground within the module. 2. Open collector; Should be pulled up with 4.7K-10Kohms to a voltage between 3.15V and 3.6V on the host board. 3. The pins are open within module.  Pin-out Connector Block on Host Board www.atoptechnology.com Rev1.0 2016-07 Page 3 10.3Gb/s XFP Transceiver Connects fiber to your home AAPX55HM0xDL40 ATOP Corporation Pin-out of Connector Block on Host Board  Recommend Circuit Schematic Absolute Maximum Ratings Parameter Symbol Min Vcc3 Typ Max Unit -0.5 +4.0 V Vcc5 -0.5 +6.0 V Storage Temperature TS -40 +85 °C Operating Humidity RH 0 85 % www.atoptechnology.com Rev1.0 Ref. Maximum Supply Voltage 2016-07 Page 4 10.3Gb/s XFP Transceiver Connects fiber to your home AAPX55HM0xDL40 ATOP Corporation  Recommended Operating Conditions Parameter Symbol Min Typ Max Unit Vcc3 3.13 3.30 3.47 V Vcc5 4.75 5.0 5.25 V Icc3 600 mA Icc5 100 mA Ref. Power Supply Voltage Power Supply Current Case Operating Temperature Bit Rate 9/125um G.652 SMF Tc 0 +70 Te 0 +85 TI -40 +85 Br 9.95 11.3 Gbps 40 km Lmax Commercial °C Extend Industrial  Electrical Characteristics (TOP=25°C, Vcc=3.3Volts) Parameter Symbol Min Typ Max Unit Ref. Input differential impedance Rin 80 100 120 Ω 1 Differential data input swing Vin, pp 120 850 mV TX Disable-High Vcc – 0.8 Vcc V TX Disable-Low Vee Vee+ 0.8 V TX Fault-High Vcc-0.8 Vcc V TX Fault-Low Vee Vee+0.8 V Vout, pp 300 850 mV 2 Data output rise time Tr 30 ps 3 Data output fall time Tf 30 ps 3 Transmitter Receiver Single ended data output swing LOS-High Vcc – 0.8 Vcc V LOS-Low Vee Vee+0.8 V Notes: 1. AC coupled. www.atoptechnology.com Rev1.0 2016-07 Page 5 10.3Gb/s XFP Transceiver Connects fiber to your home AAPX55HM0xDL40 ATOP Corporation 2. Into 100 ohm differential termination. 3. 20 – 80 %  Optical Characteristics (TOP=25°C, Vcc=3.3 Volts) Parameter Symbol Min Output Opt. Power PO Optical Wavelength Typ Max Unit -1 4 dBm λ 1530 1565 nm SMSR 30 Ref. Transmitter Side-Mode Suppression Ratio σ RMS Spectral Width(-20dB) 1 nm - dB Optical Extinction Ratio ER SONET Tx Jitter Generation(peak-to-peak) Txj 0.1 UI 3 Txjrms 0.01 UI 4 2 dB RIN -128 dB/Hz SENS -16 dBm Tx jitter Generation(RMS) 8.2 dB Path penalty at 800ps/[email protected]/s Relative Intensity Noise Receiver RX Sensitivity @10.3 Gb/s Receiver Overload -1 λC Optical Center Wavelength 1260 dBm 1600 nm -20 dBm LOS De-Assert LOSD LOS Assert LOSA -34 dBm - 0.5 dB LOS Hysteresis 1,2 Notes: 1. Measured with conformance signals defined in FC-PI-2 Rev. 10.0 specifications. 31 2. Measured with PRBS 2 -1 at 10 -12 BER. 3. Measured with a host jitter of 50 mUI peak-to-peak per Telcordia GR-253 4. Measured with a host jitter of 7 mUI RMS.  Mechanical Specifications www.atoptechnology.com Rev1.0 2016-07 Page 6 10.3Gb/s XFP Transceiver Connects fiber to your home AAPX55HM0xDL40 ATOP Corporation APX55HM0xDL40  EEPROM Information EEPROM memory map specific data field description is as below:  Digital Diagnostic Monitoring Interface Five transceiver parameter values are monitored. The following table defines the monitored parameter’s accuracy. Parameter www.atoptechnology.com Range Rev1.0 Accuracy 2016-07 Calibration Page 7 10.3Gb/s XFP Transceiver Connects fiber to your home AAPX55HM0xDL40 ATOP Corporation 0 to +70°C (C) Temperature 0 to +85°C (E) ±3°C Internal 2.97 to 3.63V ±3% Internal Bias Current 0 to 100mA ±10% Internal TX Power -1 to 4dBm ±3dB Internal RX Power -16 to -1dBm ±3dB Internal -40 to +85°C (I) Voltage  Revision History Revision V1.0 Initiated xiaoaiyou Reviewed wanggang Approved DCN New Released. Release Date July 28, 2016  For More Information ATOP Corporation Tel: +86-755-86674946 Fax: +86-755-86296723 Email: [email protected] Web: www.atoptechnology.com www.atoptechnology.com Rev1.0 2016-07 Page 8