Transcript
AB-313 ®
®
iBus Wall-Dock for A-BUS Audio Systems ®
By 7
The AB-313 is a local input module for A-BUS® audio systems that was specially designed for the Apple® iPod® and iPod mini. The attractive wall mount remains unobtrusive while not in use, yet its support ledge with integrated dock connector slides out easily, ready to dock your iPod at all times. (See Made For section on page 3 for a list of compatible iPods.) Features: Compatible with all A-BUS audio systems Charges the iPod Senses audio to automatically override the main audio source Supports IR control: compatible with A0501, A0502 or Apple Remote Uses CAT5 cabling
! ! ! ! !
Support Clip Holds the top of the iPod securely. 3 support clips are supplied: 1 for iPod mini, 1 for iPod nano, and 1 for other iPod models
Slide-out Cradle Provides support for the iPod and holds the dock connector. The support ledge slides into the AB-313 when not in use.
Dock Connector Delivers power to the iPod for charging and provides audio to the Channel Vision’s A-BUS whole-house audio system. 2
IN
OUT
1
by
2
C HANNEL V ISION
3
TM
4
Compatibility Made For iPods with dock connector: iPod video IPod nano iPod photo IPod mini 4th Generation iPod with omni (dock) connector 3rd Generation iPod with omni (dock) connector*
! ! ! ! ! !
*3rd Generation iPods are not capable of being charged by this product, but audio playback will function normally.
®
This product is compatible with all Channel Vision A-BUS products as well as all 3rd party products that carry the A-BUS Logo.
Other Required Components The AB-313 is not a standalone device. It must be installed as part of an audio system which requires the following components: Hub with Power Supply: IN
OUT
1
2
3
4 BRN WHT/BRM BLU WHT/BLU GRN WHT/GRN ORG WHT/ORG
by
C HANNEL V ISION
P-1014
AB-404
(power supply included)
OR
TM
PRO NNEL
Model P-1014 System Input
AB-T2454
CHA V I S ION
Zone 4
Module ribution BUS Dist 1 x 4 AIR
System
L
Zone 3
Zone 2
Power
Status +12VDC
+24VDC
Emitters
Signal
Priority
Expansion Output
TM
Zone 1
Local Local Input
R
Amplified Keypad: AB-114 AB-124 Single Source Input Module: C HANNEL V ISION
STATUS 12VDC
AUDIO L
R
Or By
C HANNEL V ISION
AB-202 Pwr Source
A-BUS OUTPUT
AB-202
TM
STATUS IR IR EMITTERS
Speakers: In-ceiling, In-wall and free-standing 8 ohm speakers are acceptable.
3
System Wiring Diagram Using the AB-313 as a local source input module P-1014
PRO EL
Model P-1014
Tape Monitor or Room 2 output
System Input
CHANN V ISION
TM
Sat radio System
DVD player
Zone 3
Zone 4
Module ribution BUS Dist 1 x 4 AIR
Signal
Priority
L
Zone 2
Zone 1
ion Expans Output
Status +12VDC
Power +24VDC
Emitters
Local Local Input
R
CD player
Receiver
(Optional) IR emitters
AB-313 (Rear)
C HANNEL V ISION
OUT
OUT
IN
IN
Pwr Source
AB-124 C HANNEL V ISION
TM
POWER
MODEL A0501
AB-313 (Front)
1 S O U R C E
2
3
4 ZON E POWER
MUTE
VOL
A0501 or A0502
Speakers The shuttle control buttons on the A0501 & A0502 remotes can be used to control the iPod.
4
System Wiring Diagram Using the AB-313 as a main source input module
C HANNEL V ISION
AB-313 (Rear)
Pwr Source
Pwr Source
OUT
OUT
IN
IN
C HANNEL V ISION
C HANNEL V ISION
P-1014 Pwr Source
AB-124
PRO EL
Tape Monitor or Room 2 output
Model P-1014 System Input
CHANN V ISION
TM
Zone 1
System Signal
Priority
L
BUS Di 1 x 4 A-
Zone 4
e n Modul
stributio
Sat radio DVD player
Zone 3
Zone 2
IR
n Expansio Output
Status +12VDC
Power +24VDC
Emitters
Local Local Input
R
CD player
Receiver
C HANNEL V ISION
(Optional) IR emitters
In this configuration, an iPod docked in the AB-313 will override the other audio source whenever the iPod is playing (note the position of the priority switch on the P-1014). The iPod can be controlled by pointing an A0501 or A0502 remote control at any of the amplified keypads.
Pwr Source
C HANNEL V ISION
TM
POWER
MODEL A0501
1 S O U R C E
2
3
4 ZONE POWER
MUTE
VOL
A0501 or A0502
5
Installation 1. Mount the AB-313 in a low voltage ring or junction box. 2. Install the trim ring.
3. Select the appropriate support clip for your iPod. Note: there are 3 support clips provided to accommodate standard iPods, the iPod mini, and the iPod nano. Support Clips 4. Open the slide-out cradle and dock your iPod. Slide-out Cradle
5. Enjoy your music!
Connection Tips and Troubleshooting Trouble? 1) Be sure you have connected the CAT5 cable correctly. Note that the stripe/solid pattern should match the labels on the product. Miss-wiring can cause distorted sound or prevent the system from working at all! 2) Be sure you have connected the speakers in phase. Follow the label on the product. Out of phase speakers can rob the system of its bass, especially when driving dual-voice-coil speakers. Connections: IN
6
OUT
Input/Output ... To simplify installation, the AB-313 has both 110 and RJ-45 inputs and outputs. Only one of the inputs and one of the outputs should be used at a time.
Stripping and Connecting CAT5 Wire CAT5 cable should be stripped with a proper stripping tool, such as Channel Vision’s J-110 tool. 1. Place the CAT5 between the blade and the first notch of the J-110 tool. Cat5
Blade
2. Rotate the tool only once around the CAT5. Multiple turns will cause you to cut into the inner wires. Rotate 1 turn only 3. Inspect the inner wires for damage. If any wires are cut start over at step 1.
Check for damage
Slight pressure
4. Use any standard 110 punch-down tool to properly seat all wires. Note: Do NOT use a screwdriver or any other tool that is not specifically designed for terminating UTP cable. Using improper tools will damage the connector!
Specifications: (typical @25º C) Operating Voltage : 24±.5VDC Cable requirements: CAT5 or better Operating Temperature: -10ºC to +50ºC Specifications subject to change without notice.
Apple and iPod is are trademarks of Apple, Inc., registered in the U.S. and other countries. A-BUS is a registered trademark of LeisureTech Electronics Pty Ltd. This product may be covered by one of the following patents: US patent no. 7,181,023, 6,389,139 EP 1004222, AU 739808, NZ 502982. iBus is a registered trademark of Channel Vision Technology.
7
Channel Vision Technology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts, free of charge in the USA, for two years from the date of original purchase. This is a no hassle warranty with no mail in warranty card needed. This warranty does not cover damages in shipment, failures caused by other products not supplied by Channel Vision Technology, or failures due to accident, misuse, abuse, or alteration of the equipment. This warranty is extended only to the original purchaser, and a purchase receipt, invoice, or other proof of original purchase date will be required before warranty repairs are provided. Mail in service can be obtained during the warranty period by calling (800) 840-0288 toll free. A Return Authorization number must be obtained in advance and can be marked on the outside of the shipping carton. This warranty gives you specific legal rights and you may have other rights (which vary from state to state). If a problem with this product develops during or after the warranty period, please contact Channel Vision Technology, your dealer or any factory-authorized service center.
www.channelvision.com 234 Fischer Avenue, Costa Mesa, California 92626 USA (714)424-6500 (800)840-0288 (714)424-6510 fax email:
[email protected]
500-177 revB1
