Transcript
AB-315 iBus Wall-Dock for A-Bus® Audio Systems
TM
By 10
The AB-315 is an on-wall iPod® docking station that for A-BUS® audio systems. The dock connector slides in and out to adjust for any iPod and the non-skid pad helps to hold the music player in place. With all the popular features of AB-313, the new AB-315 adds elegant and contemporary styling to make it the perfect choice for anyone who wants to enjoy their music without defacing their wall. (See Made For section on page 3 for a list of compatible iPods.) Features: ! Compatible with all A-BUS audio systems ! Charges the iPod ! Senses audio to automatically override the main audio source ! Supports IR control: compatible with A0505 or Apple Remote ! Uses CAT5 cabling ! Mounts in a standard 2-gang box
Wall Dock Front/Top
Hinged Dock Lid Rotates down to cover the dock connector
Front/Bottom
Dock Connector Connects to iPod Non-Skid Pad Secures the iPod Sliding Dock Platform Slides up to conceal the dock connector
Slide Up
Sliding Dock Lever Slides the dock connector forward, providing easy access to dock your iPod
Input RJ-45 & 110 Connectors Connect to CAT5 Audio Hub CAT5 cable (only use one)
Output RJ-45 & 110 Connectors Connect to CAT5 Audio Amplifier Input CAT5 cable (only use one) 2
Installing the Trim Plate Accessory
Install Output wall plate in j-box
Snap trim into place
Install Trim plate chassis over output wall plate Snap front cover over chassis Snap side flange on to front cover
Compatibility
Made For: ! ! iPod touch (2nd generation) iPod nano (4th generation) ! ! IPod touch (1st generation) iPod nano (3rd generation) ! ! iPod classic iPod nano (2nd generation) ! ! iPod video iPod nano (1st generation) ! ! iPod nano (5th generation) iPod mini ! iPod with dock connector 3
System Wiring Diagram Using the AB-315 as a local source input module P-1014
PRO EL
Model P-1014
Tape Monitor or Room 2 output
System Input
CHANN V ISION
TM
Zone 1
Sat radio System
DVD player
Zone 3
ribution BUS Dist 1 x 4 AIR
Signal
Priority
L
Zone 2
Zone 4
Module
ion Expans Output
Status +12VDC
Power +24VDC
Emitters
Local Local Input
R
CD player
Receiver
(Optional) IR emitters
AB-315 (Rear)
C HANNEL V ISION
Pwr Source
AB-124 C HANNEL V ISION
TM
POWER
MODEL A0501
1 S O U R C E
2
3
4 ZONE POWER
MUTE
VOL
A0501, A0502, or A0505
Speakers
The shuttle control buttons on the A0501, A0502, & A0505 remotes can be used to control the iPod. 4
AB-315 (Front)
System Wiring Diagram Using the AB-315 as a main source input module AB-315 (Rear)
P-1014
AB-124 Tape Monitor or Room 2 output
Model P-1014 System Input
PRO EL CHANN ISION
Zone 3
Zone 2
System Signal
Priority
L
BUS Di 1 x 4 A-
Zone 4
e n Modul
stributio
Sat radio DVD player
n
TM
V
Zone 1
IR
Expansio Output
Status +12VDC
Power +24VDC
Emitters
Local Local Input
R
CD player
Receiver
C HANNEL V ISION
(Optional) IR emitters
In this configuration, an iPod docked in the AB-315 will override the other audio source whenever the iPod is playing (note the position of the priority switch on the P-1014). The iPod can be controlled by pointing an A0501 or A0502 remote control at any of the amplified keypads.
Pwr Source
A0501, A0502, or A0505 5
Installing the Wall Dock Installation Steps 1. Connect all wiring. 2. Attach main chassis to j-box using the provided four 6-32 screws. 3. Feed the dock connector circuit board through the opening in the front cover. 4. Hang the front cover on the main chassis from the two top tabs. 5 5. Secure the front cover with the two small screws at the bottom. 6. Place the dock platform over 6 the slide rail and push downward until the retention snaps are engaged. 7. Slide the side protectors into the slots on the main chassis.
7
4 3 1
2 3 2 2
5 Slide Rail 6 Retention Snap
Steps 3 & 4 complete Steps 5 & 6 complete Completed Installation 6
