Transcript
AB04 COMMON EMITTER NPN TRANSISTOR CHARACTERISTICS
Analog Lab Experiment Board Ver. 1.0 QUALITY POLICY To be a Global Provider of Innovative and Affordable Electronic Equipments for Technology Training by enhancing Customer Satisfaction based on Research, Modern manufacturing techniques and continuous improvement in Quality of the products and Services with active participation of employees.
An ISO 9001: 2000 company
94-101, Electronic Complex, Pardesipura INDORE-452010, India.
AB04
Tel.: 91-731-2570301 Fax: 91-731-2555643 Email:
[email protected] Web: www.scientech.bz
Scientech Technologies Pvt. Ltd.
2
AB04
Scientech Technologies Pvt. Ltd.
3
AB04
COMMON EMITTER NPN TRANSISTOR CHARACTERISTICS AB04 TABLE OF CONTENTS
1.Introduction
4
2. Theory
5
3.Experiment
9
To study the characteristics of NPN transistor in common emitter configuration and to evaluate – Input resistance, Output resistance, and Current gain.
4.Datasheet
16
5.Warranty
18
6.List of Service Centers
19
7.List of Accessories with AB04
20
Scientech Technologies Pvt. Ltd.
4
AB04
INTRODUCTION AB04 is a compact, ready to use TRANSISTOR CHARACTERISTICS experiment board. This is useful for students to plot different characteristics of NPN transistor in common base configuration and to understand various region of operation of PNP transistor. It can be used as stand alone unit with external DC power supply or can be used with SCIENTECH ANALOG LAB ST2612 which has built in DC power supply, AC power supply, function generator, modulation generator, continuity tester, toggle switches, and potentiometer. List of Boards : AB01 AB02 AB03 AB05 AB06 AB07 AB08 AB09 AB10 AB11 AB12 AB13 AB14 AB15 AB16 AB17 AB18 AB19 AB20 AB21 AB22 AB23 AB28 AB29 AB30 AB31 AB32 AB33 AB35
Diode characteristics (Si, Zener, LED) Transistor characteristics (CB NPN) Transistor characteristics (CB PNP) Transistor characteristics (CE PNP) Transistor characteristics (CC NPN) Transistor characteristics (CC PNP) FET characteristics Rectifier Circuits Wheatstone Bridge Maxwell’s Bridge De Sauty’s Bridge Schering Bridge Darlington Pair Common Emitter Amplifier Common Collector Amplifier Common Base Amplifier Cascode Amplifier RC-Coupled Amplifier Direct Coupled Amplifier Class A Amplifier Class B Amplifier (push pull emitter follower) Class C Tuned Amplifier Multivibrator ( Mono stable / Astable) F-V and V-F Converter V-I and I-V Converter Zener Voltage Regulator Transistor Series Voltage Regulator Transistor Shunt Voltage Regulator DC Ammeter
Scientech Technologies Pvt. Ltd.
5
AB04
AB39 AB41 AB43 AB44 AB45 AB49 AB51 AB52 AB53 AB54 AB56 AB57 AB58 AB59 AB64 AB65 AB66 AB67 AB68 AB80 AB82 AB83 AB84 AB85 AB88 AB89 AB90 AB91 AB92 AB93 AB96 AB97 AB101 AB102 AB106 AB110 AB111 AB112 AB113
Instrumentation Amplifier Differential Amplifier (Transistorized) Operational Amplifier (Adder/Scalar) Operational Amplifier (Integrator/ Differentiator) Schmitt Trigger and Comparator K Derived Filter Active filters (Low Pass and High Pass) Active Band Pass Filter Notch Filter Tschebyscheff Filter Fiber Optic Analog Link Owen’s Bridge Anderson’s Bridge Maxwell’s Inductance Bridge RC – Coupled Amplifier with Feedback Phase Shift Oscillator Wien Bridge Oscillators Colpitt Oscillator Hartley Oscillator RLC Series and RLC Parallel Resonance Thevenin’s and Maximum power Transfer Theorem Reciprocity and Superposition Theorem Tellegen’s Theorem Norton’s theorem Diode Clipper Diode Clampers Two port network parameter Optical Transducer (Photovoltaic cell) Optical Transducer (Photoconductive cell/LDR) Optical Transducer (Phototransistor) Temperature Transducer (RTD & IC335) Temperature Transducer (Thermocouple) DSB Modulator and Demodulator SSB Modulator and Demodulator FM Modulator and Demodulator Log and Antilog Amplifier Crystal Oscillator (1 MHz) Peak Detector Voltage Follower & Precision Rectifier
Scientech Technologies Pvt. Ltd.
6
AB04
………… and many more
Scientech Technologies Pvt. Ltd.
7
AB04
THEORY Transistor characteristics are the curves, which represent relationship between different dc currents and voltages of a transistor. These are helpful in studying the operation of a transistor when connected in a circuit. The three important characteristics of a transistor are: 1.
Input characteristic.
2.
Output characteristic.
3.
Constant current transfer characteristic.
Input Characteristic : In common emitter configuration, it is the curve plotted between the input current (IB) verses input voltage (VBE) for various constant values of output voltage (VCE). The approximated plot for input characteristic is shown in fig. 1. This characteristic reveal that for fixed value of output voltage VCE, as the base to emitter voltage increases, the emitter current increases in a manner that closely resembles the diode characteristics.
Fig. 1
Scientech Technologies Pvt. Ltd.
8
AB04
Output Characteristic : This is the curve plotted between the output current IC verses output voltage VCE for various constant values of input current IB. The output characteristic has three basic region of interest as indicated in fig.2 the active region, cutoff region and saturation region. In active region the collector base junction is reverse biased while the base emitter junction if forward biased. This region is normally employed for linear (undistorted) amplifier. In cutoff region the collector base junction and base emitter junction of the transistor both are reverse biased. In this region transistor acts as an OFF switch. In saturation region the collector base junction and base emitter junction of the transistor both are forward biased. In this region transistor acts as an ON switch.
Fig. 2
Scientech Technologies Pvt. Ltd.
9
AB04
Constant current transfer Characteristics : This is the curve plotted between output collector current IC verses input base current IB for constant value of output voltage VCE. The approximated plot for this characteristic is shown in Fig 3.
Fig. 3
Scientech Technologies Pvt. Ltd.
10
AB04
EXPERIMENT Object : To study the characteristics of NPN transistor in common emitter configuration and to evaluate : 1. Input resistance 2. Output resistance 3. Current gain Apparatus Required :
1.
Analog board of AB04.
2.
DC power supplies +12V, +5V from external source or ST2612 Analog Lab.
3.
Digital Multimeter (3 numbers).
4.
2 mm patch cords.
Circuit Diagram : Circuit used to plot different characteristics of transistor is shown in Fig 4.
Scientech Technologies Pvt. Ltd.
11
AB04
Fig. 4
Scientech Technologies Pvt. Ltd.
12
AB04
Procedure :
• •
Connect +5V and +12V dc power supplies at their indicated position from external source or ST2612 Analog Lab. To plot input characteristics proceed as follows :
1.
Rotate both the potentiometer P1 and P2 fully in CCW (counter clockwise direction).
2.
Connect Ammeter between test point 2 and 3 to measure input base current IB(uA).
3.
Short or connect a 2mm patch cord between test point 4 and 5
4.
Connect one voltmeter between test point 1 and ground to measure input voltage VBE other voltmeter between test point 6 and ground to measure output voltage VCE.
5.
Switch ON the power supply.
6.
Vary potentiometer P2 and set a value of output voltage VCE at some constant value (1V, 3V...)
7.
Vary the potentiometer P1 so as to increase the value of input voltage VBE from zero to 0.8V in step and measure the corresponding values of input current IB for different constant value of output voltage VCE in an observation Table 1.
8.
Rotate potentiometer P1 fully in CCW direction.
9.
Repeat the procedure from step 6 for different sets of output voltage VCE.
10.
Plot a curve between input voltage VBE and input current IB as shown in Fig 1 using suitable scale with the help of observation Table l. This curve is the required input characteristic.
Scientech Technologies Pvt. Ltd.
13
AB04
Observation Table 1 : S.no. 1. 2. 3. 4. 5. 6. 7. 8. 9.
Input voltage VBE
Input current IB(uA) at constant value of output voltage VCE = 1V
VCE = 3V
VCE =5V
0.0V 0.1V 0.2V 0.3V 0.4V 0.5V 0.6V 0.7V 0.8V
•
To plot output characteristics proceed as follows:
1.
Switch OFF the power supply.
2.
Rotate both the potentiometer P1 and P2 fully in CCW (counter clockwise direction).
3.
Connect voltmeter between test point 6 and ground to measure output voltage VCE.
4.
Connect one Ammeter between test point 2 and 3 to measure input current IB(uA) and other Ammeter between test point 4 and 5 to measure output current IC(mA).
5.
Switch ON the power supply.
6.
Vary potentiometer P1 and set a value of input current IB at some constant value (0uA, 10uA......100uA)
7.
Vary the potentiometer P2 so as to increase the value of output voltage VCE from zero to maximum value in step and measure the corresponding values of output current IC for different constant value of input current IB in an observation table 2.
8.
Rotate potentiometer P2 fully in CCW direction.
Scientech Technologies Pvt. Ltd.
14
AB04
9.
Repeat the procedure from step 6 for different sets of input current IB.
10.
Plot a curve between output voltage VCE and output current IC as shown in Fig 2 using suitable scale with the help of observation table2. This curve is the required output characteristic.
Observation Table 2 : Output current IC (mA) at constant value of Output input current S.no. voltage VCE IB = 0uA IB =10uA IB =20uA IB =30uA IB =40uA 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
0.0V 0.5V 1.0V 2.0V 3.0V 4.0V 5.0V 6.0V 7.0V 8.0V
•
To plot constant current transfer characteristics proceed as follows:
1.
Switch OFF the power supply.
2.
Rotate both the potentiometer P1 and P2 fully in CCW (counter clockwise direction).
3.
Connect voltmeter between test point 6 and ground to measure output voltage VCE.
4.
Connect one Ammeter between test point 2 and 3 to measure input current IB (mA) and other Ammeter between test point 4 and 5 to measure output current IC (mA).
5.
Switch ON the power supply.
6.
Vary potentiometer P2 and set a value of output voltage VCE at maximum value.
Scientech Technologies Pvt. Ltd.
15
AB04
7.
Vary the potentiometer P1 so as to increase the value of input current IB from zero to 10 mA in step and measure the corresponding values of output current IC in an observation Table 3.
8.
Plot a curve between output current IC and input current IB as shown in Fig 3 using suitable scale with the help of observation Table 3. This curve is the required Transfer characteristic.
Observation Table 3 : S.no. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
Input current IB (uA) 00.0 uA 10.0 uA 20.0 uA 30.0 uA 40.0 uA 50.0 uA 60.0 uA 70.0 uA 80.0 uA 90.0 uA 100.0uA
Scientech Technologies Pvt. Ltd.
Output current IC (mA) at constant output voltage VCE = MAX
16
AB04
Calculations :
1.
Input resistance: It is the ratio of change in the input voltage VBE to change in the input current IB at constant value of output voltage VCE or it is the reciprocal of the slope obtained from the input characteristic. Mathematically Rin = 1 = Slope from input Characteristics
1
=
ΔIB / ΔVBE
ΔVBE ΔIB at constant V
CB
To calculate input resistance determine the slope from the input characteristic curve obtained from observation Table 1. Reciprocal of this slope will give the required input resistance.
2.
Output resistance: It is the ratio of change in the output voltage VCE to change in the output current IC at constant value of input current IB or it is the reciprocal of the slope obtained from the output characteristic. Mathematically Rin = 1 = Slope from output Characteristics
1
ΔIC / ΔVCE
=
ΔVCE ΔIC at constant I
B
To calculate output resistance determine the slope from the output characteristic curve obtained from observation Table 2. Reciprocal of this slope will give the required output resistance.
3.
Current gain: It is the ratio of change in the output current IC to change in the input current IB at constant value of output voltage VCE or it is the slope obtained from the constant current transfer characteristic. It is denoted by βac
Scientech Technologies Pvt. Ltd.
17
AB04
Mathematically βac = Slope of constant current transfer characteristic = ∆IC ∆IB To calculate current gain, determine the slope from the constant current transfer characteristic curve obtained from observation Table 3. This slope is the required current gain. Results : Input resistance Rin
= ________________
Output resistance Rout = ________________ Current Gain βac
= ________________
Scientech Technologies Pvt. Ltd.
18
AB04
DATASHEET
Scientech Technologies Pvt. Ltd.
19
AB04
Scientech Technologies Pvt. Ltd.
20
AB04
WARRANTY 1.
We guarantee the instrument against all manufacturing defects during 24 months from the date of sale by us or through our dealers.
2.
The guarantee covers manufacturing defects in respect of indigenous components and material limited to the warranty extended to us by the original manufacturer and defect will be rectified as far as lies within our control.
3.
The guarantee will become INVALID. a)If the instrument is not operated as per instruction given in the instruction manual. b)If the agreed payment terms and other conditions of sale are not followed. c)If the customer resells the instrument to another party. d)Provided no attempt have been made to service and modify the instrument.
4.
The non-working of the instrument is to be communicated to us immediately giving full details of the complaints and defects noticed specifically mentioning the type and sr. no. of the instrument, date of purchase etc.
5.
The repair work will be carried out, provided the instrument is dispatched securely packed and insured with the railways. To and fro charges will be to the account of the customer. DISPATCH PROCEDURE FOR SERVICE
Should it become necessary to send back the instrument to factory please observe the following procedure: 1)
Before dispatching the instrument please write to us giving full details of the fault noticed.
2)
After receipt of your letter our repairs dept. will advise you whether it is necessary to send the instrument back to us for repairs or the adjustment is possible in your premises.
Dispatch the instrument (only on the receipt of our advice) securely packed in original packing duly insured and freight paid along with accessories and a copy of the details noticed to us at our factory address.
Scientech Technologies Pvt. Ltd.
21
AB04
LIST OF SERVICE CENTERS 1. Scientech Technologies Pvt. Ltd. 90, Electronic Complex Pardesipura, INDORE – 452010 2. Scientech Technologies Pvt. Ltd. First Floor, 14, Uday Park, NEW DELHI – 110049 3. Scientech Technologies Pvt. Ltd. New no.2, Old no.10, 4th street Venkateswara nagar, Adyar CHENNAI – 600025 4. Scientech Technologies Pvt. Ltd. 202/19, 4th main street Ganganagar, BANGALORE- 560032 5. Scientech Technologies Pvt. Ltd. 8,1st floor, 123-Hariram Mansion, Dada Saheb Phalke road, Dadar (East), MUMBAI –400014 6. Scientech Technologies Pvt. Ltd. 988, Sadashiv Peth, Gyan Prabodhini Lane, PUNE – 411030 7. Scientech Technologies Pvt. Ltd SPS Apartment, 1st Floor 2, Ahmed Mamoji Street, Behind Jaiswal Hospital, Liluah, HOWRAH-711204 W.B. 8. Scientech Technologies Pvt. Ltd Flat No. 205, 2nd Floor, Lakshminarayana Apartments ‘C’ wing, Street No. 17, Himaytnagar, HYDERABAD- 500029
Scientech Technologies Pvt. Ltd.
Ph: (0731) 5202959 Email:
[email protected] Ph.: (011) 26513912, 26864943 Fax: (011) 26864943. Email:
[email protected] Ph.: (044) 42187548, 42187549 Fax: (044) 42187549 Email:
[email protected] Ph.: (080) 51285011 Fax: (080) 51285022 Email:
[email protected] Ph.: (022) 56299457 Fax: (022) 24168767 Email:
[email protected]
Ph.: (020) 24461673 Fax: (020) 24482403 Email:
[email protected] Ph.: +913355266800 Email:
[email protected]
Ph.: (040) 55465643 Email:
[email protected]
22
AB04
LIST OF ACCESSORIES 1.
2mm Patch cord (red) ...............................................................2 Nos.
2.
2mm Patch cord (black) ...........................................................2 Nos.
3.
2mm Patch cord (blue) .............................................................1 Nos.
Scientech Technologies Pvt. Ltd.
23
