Transcript
E
DK-02 COMPUTER DESK ASSEMBLY GUIDE Safety Precautions To avoid misuse, please follow the below instruction to prevent individual, others’ injury or property damage. If you ignore the content of the manual, it may lead to improper use or damage. The severity degrees of the damaged are categorized as below.
3. Desk foot assembly
Be sure to observe the following safety precautions
! !
Warning Caution
Caution ! Bottom panel notch toward the front, the same direction with desk foot.
It may have caused death or serious injury. It may have caused injury or property damage.
! Warning
Be careful when you pull out the drawer from the computer desk, It may lead to lean forward due to the center of gravity is instability.
! Warning
Be careful of the collisions of the keyboard tray and head phone hanger rack for the desk.
! Caution
HDMI cable length has to be 1.8 meters or longer. Desk can be increased up to 30 mm, Please refer to the description “increase the height of the desk”. After read the instruction thoroughly, Please follow the steps for assembling.
! Caution ! Caution
1. Hardware list
! Caution Do not slide it out.
B
Total are 2 cartons of components.
As shown, notch toward the front.
Assembled Computer desk Used Screws M4 x 5 (59) for desk / foot / bottom panel Screws M5 x 6 (6) for back panel
Thumb Screws (12)
Rubber washer (22)
Spare pare for monitor arm cover
for monitor arm cover & PSU mounting
Screws M4 x 7 mm (5) for keyboard tray
Rubber pads (4) for glass
C
A
Blocks (4) Increase the height of the desk Rubber pads (4) for desk foot (spare parts)
To place the left and right desk foot upside down. The approximately distance is the width of the desk top panel.
4. Headphones rack assembly
5. Back panel assembly
USB
Buzzer (2)
Screws (32) for 2.5” HDD 3-pin to 4-pin power-cord converter (3) for fan USB 3.0 to USB 2.0 converter (2) Screws M5 x 10 (16) for option fans (spare parts)
Box (1) for screws spare parts
Screws M2 x 3 mm (4) for slim ODD Cable tie (8) for cable Cable tube (2) for cable management Hexagonal copper pillar (2) for ITX M/B mounting spare parts
Thumb screws (10) for PSU mounting Clamp (8) for cable
D
Velcro (1)
E
Key (1) Locking drawer It can an be assembled on the left side or right side of the desk, Total are 5 screws.
2. Components list
A
Desk foot
E
B
Desk foot
F
1. Place back panel, make sure both sides of the holes as shown. 2. Aim to the hole precisely and fasten 4 cap screws from the inside of both sides. 3. Fasten 6 Truss head screws from the inside of both sides. 4. Fasten 5 cap screws of the bottom.
4
Assembled drawer internal HDD, slim ODD, M/B, PSU Used Thumb screws (65) for 3.5" HDD Longer thumb screws (14) for motherboard
Placed on bottom panel between the desk foot, locking 10 screws on both sides.
C
Bottom panel
G
D
1
Headphones rack
H
F
7. Desk top panel assembly Support panel
Desk top panel
3
6. Support panel assembly
! Caution Notch support panel with desk foot in the same direction.
Back panel
2
Support panel placed from the bottom up, fasten 8 screws to secure.
8. Rubber pads assembly
Drawer
! Caution Counter sink.
I
J
G
K
! Caution Rectangular hole located in this place.
Keyboard tray
Keyboard tray pad
Glass
Placed desk top panel on the desktop , fasten 18 screws to secure. 1
In four corners apply rubber pads. 2
9. Computer desk drawer assembly
13. ODD installation
H Pull out the rails from the desk, slide the drawer into the desk.
Loose the 2 screws to release the ODD tray.
! Caution Be sure to push the drawer to the end to complete the assembly.
10. Glass assembly
Removing the computer desk drawer
Loose the 4 screws on both sides to release the bezel.
14. Motherboard installation
Slide the ODD into the tray.
Fasten 4 screws to secure.
15. PSU installation
K
Pull out the drawer and then use your right thumb press and hold the right buckle, and use your left index finger to flip and hold the left buckle to unlock the rails and then the drawer can be pulled out completely.
Place the M/B on the copper bolt and secure with thumb screws.
Place power supply into the accurate position.
Fasten 4 thumb screws with rubber washer.
11. Keyboard tray assembly I
Remove air filter
Velcro
Cable tube
Pull the drawer into accurate position and pull the air filter up on both side.
Cut into a suitable size, apply on the Apply the other side of velcro on back of extension cord socket. the desk .
Cable management
High
Low
Line up the tray to the desk channels, and push down the tray gently,
! Caution Keyboard tray can be adjusted to low, medium, high loction.
Increase the height of the desk
1 2 3
Monitor arm cover
Fan tray and water cooling support
4 5 6 Loosen the 9 screws on both sides of the desk foot, Fasten the screws on 1, 3, 5 screw holes on the feet, and then place the blocks on. Option kit:
120 mm fans x 4
12. 3.5" HDD installation
2.5" HDD installation - 1
2.5" HDD installation - 2
Release the 4 screws to remove the cover.
I/O port installation 11
10
1
HD AUDIO
Placed the 3.5" HDD, and fasten thumb screws to secure.
Placed 2.5" HDD into the HDD tray, fasten the HDD to the tray bottom with 4 screws.
ODD rack can be mounted 2.5" HDD, fasten the HDD to the tray bottom with 4 screws. 3
9 7 5 3 1
GREEN KEY ORANGE N.C. GND+H.S.TUBE
BLACK / WHITE BLACK +
POWER SW
BLACK / WHITE -
POWER LED
BLACK +
POWER LED
BLACK / WHITE BLACK +
HDD LED
RED+ NC NC Blue
SPEAKER
Max.: 240 mm radiator.
USB 3.0 to USB 2.0 converter
11
1
10
USB
20
Loosen the thumb screws, Pull up and remove the HDD tray.
Cable installation guide
20
USB 3.0 Supports motherboard USB 3.0 20 Pin header
BLUE 10 BLACK PURPLE 8 YELLOW 6 GRAY 4 RED 2
Max.: 4 x 120 mm fans.
Three height can be adjusted. It can also be replaced by thumb screws.
VCC RED D- WHITE D+ GREEN GND BLACK
RED VCC WHITE DGREEN D+ BLACK GND KEY
4
