Transcript
ACCESS CONTROL AC-30C7
User manual and guarantee card
Table of contents 1. Device characteristics ...................................................................................................................4 2. Set content..........................................................................................................................................4 3. Device construction........................................................................................................................4 4. Device installation and connection diagram..................................................................... 5 5. Device operation .............................................................................................................................. 7 5.1. ENTRANCE........................................................................................................................................ 7 5.2. Door indicator ........................................................................................................................... 7 5.3. Additional functions...............................................................................................................8 5.3.1. Egress button...................................................................................................................8 5.3.2. Door magnet .....................................................................................................................8 5.3.3. Door bell.............................................................................................................................8 5.4. Entering the programming mode......................................................................................8 5.4.1. Entering the programming mode with a use of master code.....................8 5.4.2. Entering the programming mode with a use of master card....................8 5.5. Potential problems with codes..........................................................................................8 5.5.1. Losing master code.........................................................................................................8 5.5.2. Typing wrong codes.......................................................................................................8 5.5.3. General remarks about codes..................................................................................8 6. PROGRAMMING MODE.........................................................................................................................8 6.1. Access mode setting..................................................................................................................8 6.2. Master code modification.....................................................................................................9 6.3. Setting the length of a master code................................................................................9 6.4. Adding master cards...............................................................................................................9 6.5. Adding user cards and codes to zone 1.......................................................................... 10 6.5.1. Adding user card + code to zone 1........................................................................... 10 6.5.2. Adding user code to zone 1........................................................................................ 10 6.5.3. Group user card adding for zone 1....................................................................... 10 6.6. Adding user cards and codes to zone 2..........................................................................11 6.6.1. Adding user card + code to zone 2...........................................................................11 6.6.2. Adding user code to zone 2........................................................................................11 6.7. Deleting cards and codes......................................................................................................11 6.8. Unlocking time setting......................................................................................................... 12 6.8.1. Unlocking time setting for zone 1......................................................................... 12 6.8.2. Unlocking time setting for zone 2........................................................................ 12 6.9. Anti-sabotage function....................................................................................................... 12 6.10. Restoring to the default settings................................................................................. 12 7. TABLE WITH PROGRAMMING COMMANDS SUMMARY..................................................................13 8. TECHNICAL DATA.................................................................................................................................. 14 Warranty................................................................................................................................................15
Initial remarks
Before assembling, wiring and setting up of device the user should carefully read given manual. In case of any troubles with understanding the content the user should contact the producer. Unassisted assembling and start of the device can be done only with the use of proper tools. However, it is highly advised to set up a device by qualified personnel. The producer is not responsible for damages made during incorrect set-up or maintenance or in case of any unassisted repairs or modifications.
3
1. Device characteristics
Access control AC-30C7 is used in security system. The device is equipped with two relay outputs than can be used to release the lock. All functionas are programmed with a use of numerical mechanical keypad. After programming of device there is a possibility to activate unlocking function by three methods: - Unlocking with the use of proximity card only, - Unlocking with the use of combined proximity card and 4-digit code, - - unlocking with a use of either proximity card or 4-digit code. Access control is closed in vandalproof and waterproof (IP55) casing that enables the installation in any place, both outdoors and indoors. At the front of the device there is a mechanical numerical keypad. At the back there are wires to connect with lock, power supply and other optional devices.
2. Set content
Elements included in the set: - Access control, - Mounting screws, - Spline tool.
3. Device construction
Fig. 1 presents elements of the device AC-30C7. Door indicator Mode indicator
Matrix keypad
Antenna
Case screw Fig. 1. Construction of AC-30C7
4
Access control is equipped with two relay outputs that can be used to unlock the door. The devices works either with normal locks (NO/COM joints) or reversed locks (NC/COM).
4. Device installation and connection diagram
AC-30C7 should be surface mounted. Before installation, position the location where the controller unit is to be mounted, then go through the following steps: 1. 0pen the controller by loosening and removing the back case screw at the bottom using the spline tool. Back case should be moved a few millimeters up and then rotated about 20 degrees and removed.
Fig. 2. Removing the back case of access control
2. Use the provided drilling template accurately locate and drill the required holes, the four drilling holes are marked „B”.
5
Screws
Screw anchors
System wiring
Fig. 3. Installation of AC-30C7
3. Place the four screw anchors. 4. Connected accurately the system wiring 8S per the label enclosed on the rear. 1. Red 2. Black 3. Brown 4. Grey 5. Orange 6. Pink 7. Green 8. Purple 9. Blue 10. Green/White 11. Purple/White 12. Blue/White 13. Yellow 14. White 15. Shielding line
Power Supply DoorMagnet Button1 Button2
DC Input AC Input
Door Bell Shield ground Fig. 4. Wiring diagram of AC-30C7
5. Use the screws provided to mount the back case on the wall, be sure to draw the wiring through the large canter hole in back case, and keep it level. 6. Put the unit on the back case and screw it on by using the spline tool.
6
NOTES 1. All additional components shown on wiring diagram (lock, door bell, button) are not included in the set. 2. Diode D1 should be connected only when lock is DC power supplied. 3. All wires that are not used during installation should be isolated.
5. Device operation
The device is equipped with two relay outputs, enabling the user to control two zones and door bell output. Zones specifications: a) I ZONE - 1000 users, - Three options to unlock: •• Access with the use of proximity card, •• Access with the use of proximity card or code, •• Access with the use of proximity card and code. b) II ZONE - 10 zones. c) Door bell extension possibility.
5.1. ENTRANCE
Lock can be released depending on the chosen option. The steps of unlocking are presented below. To release lock with a use of proximity card the user must move the card in front of the card reader. If the card is correct door indicator will turn green (zone 1) or red (zone 2) and a short double beep will be heard. If the card is not correct – the series of 4 beeps will appear. To release lock with a use of proximity card or code the user must move the card in front of the card reader / type the code on the keypad. If the card / code is correct door indicator will turn green (zone 1) or red (zone 2) and a short double beep will be heard. If the card / code is not correct – the series of 4 beeps will appear. To release the lock with he use of proximity card and code the user must: a. At first must move the card in front of the card reader (if the card is correct a short double beep will be heard. If the card is not correct – the series of 4 beeps will appear) and type the code on the keypad. If the code is correct door indicator will turn green (zone 1) or red (zone 2) and a short double beep will be heard. If the card is not correct – the series of 4 beeps will appear. b. At first type the code on the keypad (if the code is correct a short double beep will be heard. If the code is not correct – the series of 4 beeps will appear) and then move the card in front of the card reader. Indicator will turn green (zone 1) or red (zone 2) and a short double beep will be heard.
5.2. Door indicator
Door indicator informs the user in which zone the lock was released. Door indadicator
A. When the user releases the lock from zone 1 – the indicator turns green B. When the user releases the lock from zone 2 – the indicator turns red Fig. 5
7
5.3. Additional functions 5.3.1. Egress button
It is possible to connect additional egress button to both zones 1 and 2. The details are given on the wiring diagram (fig. 4).
5.3.2. Door magnet
The device can detect the closed door – after opening and closing the door the device blocks the lock even if the set unlocking time is longer. The details are given on the wiring diagram (fig. 4).
5.3.3. Door bell
The user can connect the door bell to the device. The details are given on the wiring diagram (fig. 4). To activate the bell the user must press button *.
5.4. Entering the programming mode 5.4.1. Entering the programming mode with a use of master code To enter the setting mode the user must double type master code. The default code is 1234. Mode indicator will turn red and long beep will be heard informing about operation success. Press the button # to quit the setting mode
5.4.2. Entering the programming mode with a use of master card
To enter the setting mode the user must move the master card in front of the reader. Mode indicator will turn red and long beep will be heard informing about operation success. Repeating this operation results in leaving the setting mode - mode indicator will turn green and two shot beeps will be heard informing about operation success.
5.5. Potential problems with codes 5.5.1. Losing master code In case of losing master code the device’s power supply should be cut off and the button # must be pressed. Then the device should be powered on again and after few beeps appear the master code will come back to the default – 1234.
5.5.2. Typing wrong codes
In case of typing three incorrect codes or moving three incorrect cards in a row long beep will appear and the device will be blocked for 60s.
5.5.3. General remarks about codes
User code must be different from the master code. Codes for zone 1 must be different from codes for zone 2.
6. PROGRAMMING MODE 6.1. Access mode setting
To enter the setting mode the user must double type master code. Mode indicator will turn red and long beep will be heard informing about operation success. To enter access mode the user must press the button * and 0, the mode indicator will flash red. The user should choose proper access option by typing keys from the table below:
8
00
Access with the use of proximity card
01
Access with the use of proximity card or code
02
Access with the use of proximity card and code
After typing proper combination of keys the mode indicator will turn red and a long beep will be heard – settings were saved properly. Press the button # to quit the setting mode.
6.2. Master code modification
To enter the setting mode the user must double type master code. Mode indicator will turn red and long beep will be heard informing about operation success. To modify the master code the user must press the button * and 3 - the mode indicator will flash red and input twice a new 4-digit code – a short and a long beep will be heard – settings were saved properly. Press the button # to quit the setting mode.
6.3. Setting the length of a master code
To enter the setting mode the user must double type master code. Mode indicator will turn red and long beep will be heard informing about operation success. To modify length of a master code the user must press the button * and 9 - the mode indicator will flash red. Then the user must press 0 and 4 – a short single beep will appear, mode indicator will start flashing red – and type the number corresponding to the desired new code length (typing 2 will set code as a 2-digit code). If the single short beep appears, the settings were saved successfully. If three short beeps appear, the desired code length corresponds to the already existing one. Press the button # to quit the setting mode. NOTE Changing the master code’s length will automatically delete all saved codes from the device memory.
6.4. Adding master cards
To enter the setting mode the user must double type master code. Mode indicator will turn red and long beep will be heard informing about operation success. Then, to add master card for zone 1 the user should press buttons * and 7. If the mode indicator: -- Flashes green – there is no master card in the device memory – the user can proceed to the next step, Turns red – there already exists a master card in the device memory – before proceeding to the next step the user should double press the button * to delete existing data – as soon as mode indicator flashes green the user can proceed to the next step. The next step is adding the new card – the user should move the new card in front of the reader until the long beep is heard and mode indicator turns red – the card was added successfully. Press the button # to quit the setting mode.
9
6.5. Adding user cards and codes to zone 1 6.5.1. Adding user card + code to zone 1
To enter the setting mode the user must double type master code. Mode indicator will turn red and long beep will be heard informing about operation success. Then to add the new user to zone 1 the number from the range 000-999 should be typed – door indicator will turn green and mode indicator will flash red. Note If the door indicator turns red and mode indicator flashes red – chosen number is already added to the device memory. Double pressing the button * results in deleting code for this number. After door indicator turns green (confirming deleting the old code) the user can add a new one. Then the user must move the card in front of the reader (long beep appears and mode indicator flashes red) and type the new code (of the same length as existing master code). If the long beep appears and mode indicator turns red, the settings were saved successfully. Above steps must be repeated for adding each new user. Press the button # to quit the setting mode.
6.5.2. Adding user code to zone 1
To enter the setting mode the user must double type master code. Mode indicator will turn red and long beep will be heard informing about operation success. Then to add the new user code buttons * and 9 should be pressed - mode indicator flashes red. Then the user should press buttons 0 and 2 – short single beep appears and mode indicator turns red. The next step is choosing the number from the range 000-999 – double short beep appears, and typing new code - of the same length as existing master code. If the long beep appears, settings were saved successfully. Press the button # to quit the setting mode. Note If the chosen user already exists – the device will act in the same way, and new settings will substitute previous ones.
6.5.3. Group user card adding for zone 1
To enter the setting mode the user must double type master code. Mode indicator will turn red and long beep will be heard informing about operation success. Then to add the new user cards in group buttons * and 9 should be pressed - mode indicator flashes red. Then the user should press buttons 0 and 1 – short single beep appears and mode indicator turns red. The next step is choosing the number from the range 000-999 – single beep appears and typing the number of desired users that need to be added (e.g. typing 050 will result in adding 50 cards for 50 next users)*. After short single beep appears each card must be moved in front of the reader – after adding single card there appears at first short beep and then a long beep. Press the button # to quit the setting mode. *the user should remember to keep 3 digits of a code – if the number is smaller than 100 it should be preceded by 0 (for numbers 10-99) or 00 (for numbers 0-9).
10
6.6. Adding user cards and codes to zone 2 6.6.1. Adding user card + code to zone 2 To enter the setting mode the user must double type master code. Mode indicator will turn red and long beep will be heard informing about operation success. Then to add the new user to zone 2 the buttons * and 4 should be pressed – mode indicator flashes red - and number from the range 00-09 should be typed – door indicator will turn green. Note If the door indicator turns red – chosen number is already added to the device memory. Double pressing the button * results in deleting code for this number. After door indicator turns green (confirming deleting the old code) the user can add a new one. Then the user must move the card in front of the reader (short and long beep appear) and type the new code (of the same length as existing master code). If the long beep appears, door indicator disappears and mode indicator turns red, the settings were saved successfully. Above steps must be repeated for adding each new user. Press the button # to quit the setting mode.
6.6.2. Adding user code to zone 2 To enter the setting mode the user must double type master code. Mode indicator will turn red and long beep will be heard informing about operation success. Then to add the new user code buttons * and 9 should be pressed - mode indicator flashes red. Then the user should press buttons 0 and 3 – short single beep appears and mode indicator turns red. The next step is choosing the number from the range 00-09 – double short beep appears, and typing new code - of the same length as existing master code. If the short and long beep appear, settings were saved successfully. Press the button # to quit the setting mode. Note If the chosen user already exists – the device will act in the same way, and new settings will substitute previous ones.
6.7. Deleting cards and codes
To enter the setting mode the user must double type master code. Mode indicator will turn red and long beep will be heard informing about operation success. Then to delete the code / card buttons * and 8 should be pressed - mode indicator flashes red. Then the user should double click button 8 – if the long sound appears, the cards were deleted successfully. Press the button # to quit the setting mode.
11
6.8. Unlocking time setting 6.8.1. Unlocking time setting for zone 1 To enter the setting mode the user must double type master code. Mode indicator will turn red and long beep will be heard informing about operation success. Then to change the unlocking time for zone 1 buttons * and 1 should be pressed - mode indicator flashes red. The next step is choosing the number from the range 00-99 – chosen number corresponds to the desired unlocking time in seconds (e.g. typing 04 means changing unlocking time to 4s). If the mode indicator turns red and long beep appears, settings were saved successfully. In case of choosing value 00 – moving card in front of the reader or typing code is necessary to both release and close the lock. Press the button # to quit the setting mode.
6.8.2. Unlocking time setting for zone 2 To enter the setting mode the user must double type master code. Mode indicator will turn red and long beep will be heard informing about operation success. Then to change the unlocking time for zone 2 buttons * and 6 should be pressed - mode indicator flashes red. The next step is choosing the number from the range 00-99 – chosen number corresponds to the desired unlocking time in seconds (e.g. typing 04 means changing unlocking time to 4s). If the mode indicator turns red and long beep appears, settings were saved successfully. In case of choosing value 00 – moving card in front of the reader or typing code is necessary to both release and close the lock. Press the button # to quit the setting mode.
6.9. Anti-sabotage function In-build speaker will generate long sound for 60s in case of high light intensity detection by photo-optic sensor. It can be stopped by typing master code. To enter the setting mode the user must double type master code. Mode indicator will turn red and long beep will be heard informing about operation success. Then to change anti-sabotage function settings buttons * and 6 should be pressed - mode indicator flashes red. The next step is pressing buttons 0 and 1 – if the mode indicator turns red and long beep appears, anti-sabotage alarm is on. To turn the alarm off buttons * and 6 should be pressed (mode indicator flashes red). Then to buttons 0 and 2 should be pressed - if the mode indicator turns yellow and long beep appears, anti-sabotage alarm is off. Press the button # to quit the setting mode.
6.10. Restoring to the default settings To enter the setting mode the user must double type master code. Mode indicator will turn red and long beep will be heard informing about operation success. Then to restore the device to its default settings buttons * and 8 should be pressed - mode indicator flashes red. To finish restoring process button 9 should be double clicked. If the long beep appears, the device was restored to its default settings. Press the button # to quit the setting mode.
12
7. TABLE WITH PROGRAMMING COMMANDS SUMMARY 00
unlocking with the use of proximity card only
01
unlocking with the use of proximity card or user code
02
unlocking with the use of proximity card and user code
*1
XX (00-99)
changing unlocking time for zone 1
*3
[new master code] [new master code]
changing master code
XX (00-09)
deleting the old user (card + code) for zone 2 and replacing it with adding a new one
*0
**
*4
[new card] + [new code]
[new card] + [new code] *5 [master code] [master code]
adding the new user (card+code) for zone 2
XX (00-99)
changing unlocking time for zone 2
01
turning off the anti-sabotage function
02
turning on the anti-sabotage function
*6
** *7
*8
*9
XXX (000999)
[moving card in front of the reader]
deleting the old master card and adding a new one
[moving card in front of the reader]
adding a new master card for the first time
88
deleting all codes and cards
99
restoring to the default settings
01
XXX (000-999) XXX (000-999)
02
XXX (000-999)
[new code]
[new cards]
group adding of cards for zone 1 adding a new code for zone 1
03
XX (00-09)
[new code]
adding a new code for zone 2
04
X (2-6)
length of master code
**
[new card] + [new code]
deleting the old user (card + code) for zone 1 and adding a new one
[new card] + [new code]
adding a new user (card+code) for zone 1
13
8. TECHNICAL DATA Power supply Current (standby / work) Methods of access control Effective distance Maximum numer of users – zone 1 Maximum numer of users – zone 2 Frequency Outputs Max . load of relay contacts for lock Temperatue range Unlocking time IP Outer dimensions Netto weight
14
AC-30C7 12-16V AC or DC 30mA / 160mA Proximity card, code + proximity card, code or proximity card 5 cm 1000 codes / cards / codes + cards 10 codes / cards / codes + cards 125 kHz 2 relay outputs (NO/COM/NC) 3A/12V DC -18°C...+50°C 0…99 s (programmed from keypad) IP55 150 x 44 x 24 (mm) 0,41 kg
Warranty As the only distributor of the Eura products, Eura-Tech is obliged to ensure efficient warranty and post-warranty service. In the countries where Eura-Tech has neither its own service network, nor DOOR-TO-DOOR service, the quality claims are dealt with by authorised distributors of the Eura products on the basis of the signed distribution agreements. Within the framework of such agreements, Eura-Tech will ensure financing of the possible repairs and delivery of spare parts.
15
EURA-TECH Sp. z o.o. 84-200 WEJHEROWO, ul. Przemysłowa 35A tel. +48 58 678 81 00, service: tel. +48 58 678 81 20, fax +48 58 678 81 01 www.eura-tech.eu
All rights reserved. Pictures, graphs and texts are the property of “Eura-Tech” Sp. z o.o. Copying, distributing and publication without permission of author is forbidden.
