Transcript
Access Control | PAC 530 Output Controller Overview The PAC 530 Output Controller communicates directly with the PAC 500 Access and Alarm Server, ensuring complete system security, resilience and reliability, when integrated with Stanley PAC security management software. It often acts as a key component in elevator access control. The PAC 530 monitors and controls ten 2-Amp and two 8-Amp programmable output relays are configurable as latched, momentary, toggling or pulsing. Two control inputs are configurable as Normally Open (NO) or Normally Closed (NC), with optional supervision via three or four state monitoring allowing the connection of devices like alarms, motion detectors and temperature sensors. The Output Controller can also be used to integrate an elevator system within a Stanley PAC access control environment. Each PAC 530 can control up to 12 floors and multiple PAC 530s can be combined per car. Operating in conjunction with an PAC 500 and Two-Door Controllers (PAC 512 series) each floor is configured as an area and can be programmed with a specific period during which only access is possible to cardholders with appropriate access privileges. Options also include out of hours access and exit, together with an optional additional button selection time (ADA compliance). The One-Touch™ installation mode shows the state of each input and output providing instantaneous polling and communication status at the controller with just the press of a single button, avoiding the need for a PC, complex programming and DIP switch configuration.
Key Features Ten Form-C 2-Amp contacts for load switching Two Form-C 8-Amp contacts for load switching Two programmable supervised or non-supervised user inputs 10.5 to 28VDC input power Dedicated override and tamper inputs Up to 48 output controllers can be multi-dropped via RS-485 from a single PAC 500 Connects to the PAC 500 via RS-485 Receives and processes real time commands from the PAC 500 Reports all activity to the PAC 500 Enables complex input and output linking with the PAC 500 and PAC 520 Status LEDs show the states of all Inputs and Outputs Watchdog timer for maximum reliability One-Touch installation test mode. This installer test facility enables the TM
functionality of each controller and its associated circuits to be tested locally, by simply pressing a single button without the need for a PC or programming Elevator control Onboard RS-485 termination jumper One polyfused 100mA auxiliary voltage output AC status monitored and reported Downloadable firmware updates DIN-Rail mounting for ease of installation (removable)
READYKEY ™
COMPATIBLE
ELEVATOR CONTROL
CCTV
THE OUTPUT CONTROLLER IS A KEY COMPONENT IN AN ELEVATOR ACCESS CONTROL SYSTEM.
IN
NC
NC
TAMPER
NC
NO
NO
2
www.stanleypac.com
1
0V
INPUTS
ALARM BEACON
POWER
VIN
NO
COM
COM
COM
AIR CONDITIONING
RELAY 1
One-Touch™ Testing To enter View Mode press the One-Touch button momentarily. To enter Active Mode press and hold the One-Touch button for 2 to 4 seconds. To leave One-Touch testing, press the button momentarily again. Note that One-Touch Active mode will automatically time out after 1 hour. For details of One-Touch modes see the enclosed Quick Start Guide .
RELAY 2
0V MSTAT
0V
SIG
NC
NO
COM NC
COM
NO
NO
LED
COM
VOUT Made in UK
Model No.
PAC530 Output Controller
X Date Code NC
NC
COM
NC
RELAY 12
NO
RELAY 11
NO
RELAY 10
COM
NC
NO
NC
VOUT 1-2 - VIN: 100mA RELAY 1-2 - 30V; 2A RELAY 11-12 - 30V; 8A
0V
TAMP
NGND
NC
NO
NO
COM
COM
NC
VOUT2
0V
0V
0V
TAMP
OVRD
MSTAT
VOUT2
MSTAT
www.stanleypac.com
One-Touch™ Testing To enter Active Mode press and hold the One-Touch button for 2 to 4 seconds. To leave One-Touch testing, press the button momentarily again. Note that One-Touch Active mode will automatically time out after 1 hour. For details of One-Touch modes see the enclosed Quick Start Guide (17473).
-
+
TX
RELAY 3
RELAY 4
OUTPUT CONTROLLER (PAC 530) (12 OUTPUTS AND 2 INPUTS PER PAC 530)
FUSE 2 TRIPPED
FUSE 1 TRIPPED
PLANT
ELEVATOR CAB
STATUS
POWER
BATTERY
VIN
Made in UK
Model No.
X Date Code
READER
0V
RS-232
0V
N0
N1
OUT
PAC 500 Access and Alarm Server
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
VOUT 1-2 - VIN; 5A
CAUTION - INTERNAL BATTERY See manual for disposal of unit.
INPUT: 10.5-28.0VDC; 0.4A (SERVER ONLY)
RS-485
NGND
NET2
RXNet
MAINS ON
POWER OUT
RX
RS-485
CTS
N1
N0
NGND
LAN
TXNet
TXNet
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
INPUT: 10.5-28.0VDC; 0.4A (CONTROLLER ONLY) TX
1416/2 COMPACT FLASH
DTR
NET1
RXNet
OVRD
N1 N0 RX
IN
1400/2
AUX
RELAY 7
RELAY 9
RS-485
TERM1 OUT
RELAY 6
RELAY 7
NO
RELAY 8
COM
ON PRESENTATION OF A VALID CREDENTIAL TO THE CAB CARD READER, THE PAC 500 SENDS A COMMAND TO THE PAC 530 WHICH ENABLES THE CORRESPONDING DOOR BUTTONS. THE CARDHOLDER CAN THEN PRESS A BUTTON AND BE TAKEN TO THEIR FLOOR SELECTION.
COM
LIGHTING
RELAY ON
TERM2 RX TX
ACCESS AND ALARM SERVER (PAC 500)
TX
RX
CTS
0V
DTR
RS-232
CAB CARD READER ACCESS CONTROLLER (PAC 512)
CONTROLLERS AND OPTIONS 7S-530
PAC 530 Output Controller (DIN-Rail Mount)
7S-DIN4X 7S-DIN6X 7S-PSU3A 7S-PSU7A
Metal, lockable DIN-Rail Enclosure (20.47 in x 19.69 in. x 3.74 in.) accommodates 4 devices, UL Listed Metal, lockable DIN-Rail Enclosure (27.56 in. x 19.69 in. x 3.74 in.) accommodates 6 devices, UL Listed 12 or 24 VDC 3 A power supply with built-in charger for sealed lead acid or gel type batteries (DIN-Rail Mount) 12 or 24 VDC 7.2 A power supply with built-in charger for sealed lead acid or gel type batteries (DIN-Rail Mount)
SPECIFICATIONS Primary Power Input Power: Communication Ports Outputs Inputs Input Control Points Tamper and Door Override: Power Fail Monitors (MSTAT): Status LEDs Wiring Requirements Mechanical Dimensions: Weight: Environmental Temperature: Humidity: Approvals: Warranty
The PAC 530 is for use in low voltage, power limited, class 2 circuits only 10.5VDC @ 60mA to 28VDC @ 30mA RS-485 Ten 2-Amp Relay Outputs, configurable as latched, momentary, toggling or pulsing Two 8-Amp Relay Outputs, configurable as latched, momentary, toggling or pulsing 2 programmable supervised or non-supervised contacts Software configurable as N/O (normally open), N/C (normally closed) and two, three and four state sensor configuration Programmable as supervised or unsupervised circuits, dedicated Unsupervised, dedicated RS-485, Input Status, Output, System Status RS-485: CAT5 or CAT 6 up to 3000ft or 22AWG cable up to 500ft total cable H: 7.3" W: 5.1" D: 5.1" 14oz. nominal Operating: 14F to 130F Storage: -13F to 176F 0 to 85% RHNC ETL certified for UL 294. CE-marked and ROHS compliant 5-Year Limited Warranty
© Copyright 2015, Stanley Security Solutions, Inc. All Rights Reserved. The information contained herein is subject to change without notice. Stanley shall not be liable for technical or editorial errors or omissions contained herein. Stanley, PAC, Stanley PAC, One-Touch are registered trademarks of Stanley Security Solutions, Inc. Readykey is a registered trademark of Stanley Security Solutions, Inc in the European Union, UK and Australia and of Bosch Security Inc. in the USA. All other trademarks are the property of their owners. Rev. AJM5/15
Visit us at...
LIFT
