Transcript
ACCESS CONTROLLER up to 10 Magnetic Cards. OPERATING MODE.
The DA-00 is an access control by magnetic card with 10 units as maximum capacity. It includes places controls to authorize, introduce, deny, consult and setup cards. It allows to change the serial number to use several controllers in a same place. The output is by relay, with adjustable timings. Module including: Indication Leds, Cards reader and cards identification.
TECHNICAL CHARACTERISTICS. 12 V. D.C. 10 mA / 70 mA. 5 A. Magnetic Cards - Mod. Cebek Piste 2 ISO. 10 Cards. 500.000 Reads. 10 cm/sec. 150 cm/sec. 1 - 4 sec. 100 x 44 x 36 mm. 94 x 62 x 35 mm.
Cards Authorisation. With the serial authorisation, the module is programmed to be used with a complete exclusivity as concern your cards, then you have to indicate which cards have an authorised access. To do that, and into the Program Mode (Set jumper closed), you have to press several times the select touch up to arrive into the Authorisation function, where the Charge Led will light. Like for the serial authorisation, you have to insert two times the card that you wish to authorise. The first time, the green Led “ON” will light and the acoustic indicator generates a short signal. The second time, the confirmation one, the acoustic indicator will generate a longer signal and the Green Led stop its intermittence, being lighted some seconds and then light off. If the process is done like this, the inserted card will be authorised. Otherwise, the error will be indicated thanks to a Red Led “OFF”. Repeat this process to authorise new cards, waiting between each authorised card that the Led “ON” light off.
INSTALLATION. POWER SUPPLY. The DA-00 circuit had to be supplied by a 12 VDC power supply correctly filtered. We recommend you to use the FE-103 power supply, which has been developed to perfectly answer to the circuit needs instead of standard power supply or rectifiers who can damage the circuit. Install a fuse and a switch has it is indicated on the schedule. Both are necessary for the module's protection as well as for your own safety, as it is required by the “CE” regulations. Connect the positive and the negative of the power supply to the respective positive and negative terminals of the module, indicated in the wiring map. The distance between the power supply and the module has to be as short as possible. Verify that the assembly is correct and read the instruction manual before to activate the switch. OUTPUT CONNECTION. LOAD. The DA-00 output is controlled by a relay, and accepts any device up to 5 A. The relay is not a component supplying voltage but its function is limited to accept or deny the voltage passage like a standard switch. For this reason, you have to supply the load through this component. The relay has three output terminals: The normally open quiescent (NO), the normally closed quiescent (NC) and the common. Install it between the Common and the NO in accordance with the Fig.1. For the inverse function you have to place the load between the NC and Common
Fig. 1. How To Connect The Load
230 V AC CONNECTION
Common Apparatus,
230 V. A. C.
Load.
INFORMATION ABOUT THE OUTPUT. During the operating mode and according to its load, it could happen a fluctuation or an incorrect working of the output. In such case, you have to install an anti-spark circuit between the two relay's contacts used for the connection. If the load connected to the relay of the circuit is supplied at 230 V AC, you have to use 100 nF/400V type X2 Capacitor and a 47W. ½ W resistor) as it is indicated on the drawing. NO 47 W 1/2W. If the load is supplied at 12 or 24 V DC, you have to NC 100nF/400 V. suppress the resistor between both contacts and install X2 Common only the X2 capacitor. You have to make tests with values Apparatus, Load. between 10 nF and 47 nF, up to suppress the fluctuation.
ACCESS CONTROL MODE. Once serial authorisation operations, cards authorisation, etc… done, you only have to place the DA-00 where you want to control the access and start its operating. To activate the Access Control Mode, the DA-00 have to have all Program Leds (Charge, Discharge, Check and Serial) light off. Then, you have to press several times the Select touch and the Set jumper has to be maintained open. Then, each time that you will insert a card into the reader, the DA-00 checks its status. If the card is not authorised, the red Led “off” will shortly light and the acoustic indicator emits a signal to indicate at the user that the access is denied. At the opposite, if the card is authorised, the module will valid the access connecting the relay and activating the output. The green Led “ON” will light and the acoustic indicator emits a signal to confirm. The relay connection time, authorising the access to a card, can be adjusted between 1 and 4 sec. Put dips of the Time Switch according to the required timing. See Fig.5. Fig. 5. Configuration du temps d’activation du relais.
the Load.
Jumper
Deactivation
1 2
Time Timing for 1 sec.
Time Timing for 2 sec.
LSB MSB
1 2
Time Timing for 3 sec.
1 2
Time Timing for 4 sec.
TO PERSONALISE CARDS. The DA-00 is supplied with two main cards, the rest of cards up to 10 (if it is necessary) have to be obtained as accessory. Please consult your distributor. Cards have an adhesive film allowing to protect with plastic or personalise them with your own data.
Jumper Activation
OPERATING MODE. OPERATING. The module operating can be divided in two parts or concepts, Program Mode and Access Control Mode. CARDS INSERTION. Before to introduce you into the Program Mode or to use the Access Control Mode, you have to correctly learn how to pass cards into reader. This operation is important and indispensable for all operating modes in this circuit. The Fig.3 shows the correct way to place and to introduce the card into the Fig 3. To Insert the Card. reader. The back of the card, with the magnetic part (band), has to be placed in the reader side indicated with an arrow, and the band has to be maintained on the reader interior side. Once the card correctly placed, at normal speed (not to fast neither to slow) Magnetic Band you have to slide the card into the reader, up to down following the way Back of the indicated by the narrow. Card If you slide cards according to these indications, the module will perfectly read cards and allows you to do all necessary operations.
2.
1. Print the label card or
picture with your data or write them. .
3. Press with your finger to
Remove the silicone protector paper and glue the label..
facilitate the adherence.
GENERAL WIRING MAP. Feed Communication cable with reader 12 V. D.C.
Power
Check Charge
Led
On Off
Discharge Select
Jumper Indicator
Serie
Module
DA-00
Set
Transformer LSB
Reader
Voltage Adjustment
To record the serial number. Authorisation of the serial. The first operation to do it to authorise the serial number. Theoretically, there are several users with a Communication Cable DA-00 and all have cards compatible with yours. Then, this situation will allow to the Main Board to any foreign person, but having a CEBEK card with a number recorded in your reader, to be authorised. To avoid this situation, each DA-00 module is supplied with a pack including two cards including an exclusive and internal coded number which difference it from any other DA-00. your reader, to be authorised. To avoid this situation, each DA-00 module is supplied with a pack including two cards including an exclusive and internal coded number which difference it from any other DA-00. This “serial number” has to be authorised in the reader to allow the circuit to accept the rest of operations like authorisation, deny, check, etc…. then it only reads cards having this code and refuses other users with similar cards. To authorise this serial number, you have to accede to the Program Mode, (open or close the Set Jumper), and press several times the select touch up to light the Serial Led. Then, insert one time in the reader one of the two cards supplied with the module. The module will read the serial number and you have correctly inserted the card, the acoustic indicator will generate a sound and the green Led “ON” intermittently light. If the led doesn't answer like this, that means that you have wrongly inserted the card into the reader. Please repeat this operation. Any mistake will be indicated by the DA-00 thanks to the light of the Led “OFF”.
L
Fuse
MSB
LSB MSB
1 2 3 4
Card
Enter
1 2
No Nc Common
Time
Input
N
Side and Way to Read
Acoustic Indicator
Module
FE-103 PROGRAM MODE. See the drawing “General Wiring Map”. To accede to the Program Mode, firstly you have to close the SET jumper, otherwise, the module doesn't allow the control of these operations. Once the jumper closed, each pressure on the SELECT touch will commute between the fours program functions (Check, Authorisation, Deny and Serial) and the corresponding Led will light.
LSB MSB
1 2
Output
CONNECTION between READER and MAIN BOARD. The interconnection cable between the module and reader can't be removed, suppressed, increased or modified.
Fig. 2. To Activate / Deactivate a Jumper.
LSB MSB ON
ON
LSB MSB
ACOUSTIC INDICATOR. The DA-00 has an acoustic indicator which function is to indicate and to emphasize through sounds, several modules' operations. If you wish to deactivate it, you have to disconnect the jumper placed close to it. See the drawing “General Wiring Map”. To activate it again, oyu have to connect again the jumper.
Mains Switch Mains (230 V. A.C.)
TECHNICAL CONSULTATIONS. If you have any doubt, you could contact your wholesaler or our Technical Department. - E-Mail,
[email protected] | Fax. 34.93.432.29.95 | by mail. P.O. Box. 23455 - 08080 Barcelona - Spain. - Keep the invoice of this module. For any repair, the corresponding invoice had to be added. If the invoice is not presented together wish this module, the module’s warranty will be automatically cancelled. All the module’s CEBEK have 3 years of total warranty in technical repairing, and spaces from the date of buy. Much more CEBEK module’s are aviable in our products range, please, require our general catalogue or visit our Web side. Http://www.cebek.com
GARANTIA
3
AÑOS TO TAL YEARS
ANYS
To feed
INSTALLATION. The device has to be insulated to interferences form other devices and to parasites from the mains. Use a mains filter if necessary and place the module in a place protected against perturbations.
4
Off Off Off Off Off Off Off Off On On On
WARRANTY
GARANTIA
Apparatus, Load
3
Off Off Off Off On On On On Off Off Off
ANNÉ
12 V. D.C.
ON
Common
2
Off Off On On Off Off On On Off Off On
GARANTIE
Normally Closed, (NC)
1
Off On Off On Off On Off On Off On Off
Relay
Normally Open(NO)
Normally Closed, (NC)
Switchs Number 0 Number 1 Number 2 Number 3 Number 4 Number 5 Number 6 Number 7 Number 8 Number 9 Number 10
Led Relay
Normally Open(NO)
Fig. 4. To configure the Card Number.
To Deny Cards. Thanks to this function you can erase from the circuit's memory cards previously authorised. You never erased the information inserted into the card but only the access to the module. To activate the “Deny card” function in the Program Mode, you have to press several time the Select touch up to light on the Discharge Led. Then, you have to introduce through the card switch the card number that you want to deny. Like for the Check function, the card number has to be inserted in binary code. See the Fig. 4. Once the card number corresponding to card switch configured, you have to press the Enter touch and the card will be automatically denied (the Led “OFF” shortly light on).
ON
12 V DC CONNECTION
Check Function (Verification). The check function allows to verify that cards have been authorised in the circuit and then if they have access or not. In Program Mode, you have to press several times the select touch up to the Check Led lights. The verification operation is done through the Card switch composed by 4 dips. Using this card switch and in binary code, you have to indicate the card number that you want to check. The dip Nº1 corresponds to the bit with lower weight (Lsb) and the dip Nº4 corresponds to the bit with higher weight (Msb). Then you have to combine in ON or OFF position the 4 dips according to your needs. See the Fig. Nº4. Then, press the Enter touch. If the indicated card on the card switch has been previously authorised in the module, the green Led “ON” will momentary light on. Otherwise, if the card hasn't be authorised in the module, the red Led “OFF” will light to indicate this situation. If you want to check the status of any other card, you have to repeat this process.
ON
Voltage. ............................................................................................ Minimum/Maximum Consumption. ................................................. Maximum Ouotput Load. ................................................................ Read. ................................................................................................ Maximum Storage Capacity............................................................... Approximative Life of the reader’s Head. ......................................... Minimum Speed to insert the Card. ................................................. Maximum Speed to insert the Card. ................................................ Time to connect the output. ............................................................ Reader’s sizes. .................................................................................. Basic circuit’s sizes. ...........................................................................
After the first correct card's read, (Green Led “ON” intermittently lighting), you have to insert once again the same card into the reader, the acoustic indicator will generate a sound different from the first and the green Led “ON”, will momentary light. After this operation, the serial number will be recorded into the circuit, even if you disconnect the power supply. Note. Each time you authorise a serial number, all previous stored data into the module (like card numbers, etc…) will be erased.
ON
ENGLISH.
DA-00
ELECTRONIC CIRCUITS
Rev. Full0324
