Transcript
Hydraulic Chain Saws Models ACH000-12, ACH000-14, ACH000-16, ACS-70 and ACS-80 A Full Line of Hydraulic Pruning Tools
Specifications Max. pressure.............. 2000 PSI (130 bar) Flow range................... 4-8 GPM (15-30 LPM) Hose size..................... 3/8” - I.D. minimum Inlet port....................... 3/8” JIC - #6 Outlet port.................... 3/8” JIC - #6 Foreign particles.......... 10 micron max. SAFETY! WE URGE YOU TO READ AND UNDERSTAND ALL THE SAFETY INSTRUCTIONS IN THE OPERATION AND SERVICE MANUAL BEFORE SERVICING THIS TOOL
CS Unitec, Inc., 22 Harbor Ave., Norwalk, CT 06850 • Toll-free: 800-700-5919 • Phone: 203-853-9522 • Email:
[email protected]
www.csunitec.com
CS Unitec, Inc., 22 Harbor Ave., Norwalk, CT 06850 • Toll-free: 800-700-5919 • Phone: 203-853-9522 • Email:
[email protected]
www.csunitec.com
No.
Part No.
Description
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23A 23B 23C 23D 24 25 26 27 28 29 30 31A 31B 31C 31D 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53A 53B 54A 54B 55 56 57 85 86 87 88 89 90 91 92 93 * * *
00640006 00640036 00640121 00640062 00640037 00640007 00640009 00640090 00640008 00640094 00640122 00640026 00640120 00640069 00640035 00640050 00650010 00640049 00640068 00650060 00640096 00640230 00650032 00650033 00650034 00650035 00650051 00650052 00650053 00650040 00650054 00650071 00650065 00650036 00650037 00650038 00650039 00650041 00650055 00650056 00650013 00640040 00650023 00650057 00650255 00650249 00650229 00650246 00650245 00650061 00650050 00650026 00650063 00650062 00650058 00650024 00650012 00650022 00650107 00650103 00650106 00650102 00650025 00650014 00650059 00640200 00640203 00640206 00640204 00640201 00640231 00640002 00640068 00640069 00650199 00640232 00650000
Screw – (1/8" x 1/2" NC) Spring Trigger Guard Plate (Left) O-Ring (3-907) Connector Screw – (3/16 x 1/2" NC) Screw – (3/16 x 1" NC) Ultramid Handle Nut – (3/16" NC) Screw – (M4 x 22) Trigger Guard Plate (Right) Lock Spool Cap O-Ring – (2 - 012) Spring Spool Housing Pin O-Ring (2 x 1.5) Screw – (5/16" x 1-1/4" NC) Trigger (Finger Version) Trigger Guard (Finger Version) Hose Model ACS-50 Hose Model ACS-60 Hose Model ACS-70 Hose Model ACS-80 O-RIng – (2 - 219) Back Up (8 - 014) O-Ring (2 - 014) Plate Screw (3/16" x 1/2" NC) Screw (3/16" x 5/8" NC) Hand Stop Safety Collar Fiberglass Extension Tube ACS-50 Fiberglass Extension Tube ACS-60 Fiberglass Extension Tube ACS-70 Fiberglass Extension Tube ACS-80 Plate Screw – (5/16" x 1/2" NF) Screw – (1/4" x 5/8" NC) Front Hose Connector Open/Closed Center Plug Bolt O-Ring – (2 - 111) Saw Motor Key Sprocket Support Sprocket Sprocket Adaptor Lock Nut – (1/2" NF) Cotter Key Sprocket Cover Screw – (1/4" x 1-1/4" NC) Screw – (1/4" x 3/8" NC) O-RIng – (2 - 010) Saw Bar Nut Bar Mount Metering Screw Saw Bar – 12" Saw Bar – 14" Saw Chain – 12" Saw Chain – 14" Adjusting Nut Bar Support Tension Screw Trigger Assy. (Glove Version) Trigger (Glove Version) Guard (Glove Version) Screw – (3/16" x 5/16" NC) Stopper (Glove Version) Housing (Glove Version) Screw – (1/8" x 1/4" NC) O-RIng – (2 x 1.5) O-Ring – (2 - 012) Seal Kit Stickers kit Operation and Service Manual
MOTOR ASSEMBLY
Item No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
QTY 1 4 1 1 1 1 2 1 1 1 2 1 1 1 1 8
Description Housing Bushing Shaft Gear Gear Bearing Key Cover Retainer Snap Ring Pin O Ring O Ring Seal Bolt Bolt
Part No. 00650075 00650282 00650296 00650278 00650279 00650097 00650249 00650277 00650098 00650095 00650276 00650058 00650100 00650099 00650064 00650241
CS Unitec, Inc., 22 Harbor Ave., Norwalk, CT 06850 • Toll-free: 800-700-5919 • Phone: 203-853-9522 • Email:
[email protected]
www.csunitec.com
OPEN/CLOSED CENTER CIRCUIT
DIRECTION OF FLOW
The ACS model can be operated on an open or closed center hydraulic circuit. To convert from open
closed center circuit:
CHAIN TENSION ADJUSTMENT
a. Remove ultramid handle (8). b. Remove return hose. c. Remove return hose connector (5). d. Install or remove open to closed center plug (36). PLUG OUT – open center circuit PLUG IN – closed center circuit Note: For your convenience you can store the plug on the tool when not in use.
CHAIN OILER ADJUSTMENT
a. Let the chain turn until all of the accumulated oil is thrown off. b. Point the “nose” of the guide bar toward a clean, dry smooth surface. c. Turn the chain while keeping the “nose” of the guide bar approximately 2” from the surface. d. Check the oil discharge from the guide bar “nose”. There should be a light oil accumulation on the surface. e. If no oil appears, screw out the adjustment screw (52) 1/8 – 1/4 turn and then recheck. f. If too much oil is discharged, screw in the adjustment screw 1/8 – 1/4 turn and recheck Note: A dry chain will heat up and cause excessive wear on the bar and chain
a. Disconnect tool from power source. b. Make sure to wear protective gloves. c. Saw chain and bar should be cool when checking or adjusting chain tension. d. Loosen the two guide bar securing bolts (20). e. Turn adjusting screw (57) until chain tension is properly adjusted. (1/8” chain clearance at the bar center). f. Tighten the guide bar securing bolts (20). g. Freely run the saw for a few minutes. h. Re-check chain tension (disconnect tool power source!)
SAFETY DECALS
22 Harbor Ave., Norwalk, CT 06850 Toll-free: 800-700-5919 • Phone: 203-853-9522 Email:
[email protected]
www.csunitec.com
1215
