Transcript
ACTpro Readers Installation Manual ACTpro Readers Wiring Diagram - For systems with Clock & Data Cards Wiring for ACTpro Reader SENSE Clock / Data1 Data / Data 0 +12V 0V Red Led Green Led (Buzzer Ctrl)
Controller
SENSE Clock / Data1 Data / Data 0 +12V 0V Red Led Green Led
The standard wiring colours for ACTpro Proximity & Pin readers are shown above. Connect the SENSE line to the Controller if you require an Entry Reader. Leave the SENSE line unconnected for an Exit Reader. The ACTpro readers are compatible with ACT RFID and HID cards and fobs.
ACTpro 1030 Proximity Reader (Exit)
Card/Prox Reader
White Green Blue Red Black Brown Yellow Orange
ACTpro 1050 Pin & Proximity Reader (Entry)
Internal buzzer is activated by applying 0V to Buzz Ctrl (Orange Wire)
ACTpro Readers Wiring Diagram - For systems with Wiegand cards: D0 of Exit Reader
ACTpro 1030
Controller
Entry Reader
Card/Prox Reader
SENSE Clock/Data 1 Clock/Data 0 +12V 0V RED GREEN
To put the Reader into Wiegand Mode Connect the SENSE line on the readers to 0V. To use both the entry and exit reader wire both readers in parallel but connect the Data 0 line of the exit reader into the SENSE line on the controller.
Connect Reader SENSE to 0V.
Rear view of ACTpro 1040/1050/1060 onnected to the ACT Controllers 02XX-1 ACTpro Rev 1.0 00XXXX 5 6 7 8 9
1A 125VAC 30VDC
BATCH: PRODUCT: SERIAL #: 0 1 2 3 4 OMRON
Backlight enabled link (ACTpro reader must be powered from +12V)
5A 250VAC 5 A 3 0 V DC OM RON
5-12V DC
0V
Data / D0
Red LED
Clock / D1
Grn LED
Sense
Buzz Ctrl
Internal buzzer is activated by applying 0V to Buzz Ctrl
SENSE CLOCK DATA +12V 0V RED GREEN
Note The ACTpro readers are 5V and 12V compatible
Access Control Technology, Unit C1 South City Business Centre, Tallaght, Dublin 24 Phone: +353 1 466 2570 UK Lo-call 0845 300 5204 E-mail:
[email protected] Web: www.accesscontrol.ie
18-00077 Issue 1
Mounting Instructions for ACTpro Readers Spacers break away from main component when required by installer for use View showing spacer stacking
View showing mounting plate before spacers are broken away by installer
Flush Mount Unit
Note: Determine the distance between the patress box and the mounting plate, using the spacers that are labelled 1mm to 4mm. A spacer of the correct length is assembled by stacking the spacers together.
Security screw supplied with the unit
Standard pattress box
Screws
Mounting plate is attached to the pattress using the screws supplied. Ensure the corect spacers have been used to bridge the gap between the mounting plate and the fixing wings of the pattress box to avoid the mounting plate being distorted.
Place the cap onto the unit and push firmly in place
Place the reader / keypad onto the surface mount collar and clip down into place. Use the security screw supplied to attached the unit to the flush mount collar.
Surface Mount Unit
Security screw supplied with the unit
Place the cap onto the unit and push firmly in place
The surface mount collar is mounted on the wall using the fixing kit supplied in the box.
Place the reader / keypad onto the surface mount collar and clip down into place. Use the security screw supplied to attached the unit to the surface mount collar.
Access Control Technology, Unit C1 South City Business Centre, Tallaght, Dublin 24 Phone: +353 1 466 2570 UK Lo-call 0845 300 5204 E-mail:
[email protected] Web: www.accesscontrol.ie
