Transcript
Quad Video Server SED-2300Q Ver. 070821
Quick Installation Guide
11 1.1
Getting Started
PACKAGE CONTENTS SED-2300Q
Warranty Card
Product CD
Terminal Blocks & Screws
Power Adaptor (Option)
1.2 PHYSICAL DESCRIPTION Read the following information to familiarize yourself with the video server, and make particular notes of where the connectors and LEDs are located.
Front Panel
1.
Red LED LED indicating Power or H/W Reset Function
2.
Yellow LED LED indicating when RS-485 is active
3.
Green LED LED indicating when LAN/WAN is active
4.
Reset Button Get back to default value while forgetting Login Name & Password Procedure 1.
Switch off the video server by disconnecting the power cable
2.
Using a suitable pointed object, press and continue to hold the Reset Button depressed. While continuing to hold the Reset Button depressed, reconnect the power cable.
3.
Keep holding the Reset Button depressed around 6 seconds, release the Reset Button. The unit will start up with the factory default settings.
5.
Terminal Blocks Pin 1~6
PIN 1 2 3 4 5 6
NAME DO1 NC GND DI1 NC GND
DESCRIPTION Digital Output 1 Non Connector Ground Pin Digital Input 1 Non Connector Ground Pin
6.
7.
Terminal Blocks Pin 7~12
PIN
NAME
7 8 9 10 11 12
Rx+ TxNC NC 12V GND
DESCRIPTION RS-485 RS-232 D+ Rx DTx Non Connector Non Connector Power Input (DC +12V) Ground Pin of Power Input
WAN port The video server connects to the WAN (wide area network) via a standard RJ45 connector. Supporting NWAY, this video server can auto detect the speed of local network segment (10Base-T/100Base-TX Ethernet). The WAN port is for FTTH and can connect to a xDSL or cable modem.
8.
LAN port The video server connects to the LAN (local area network) via a standard RJ45 connector. Supporting NWAY, this video server can auto detect the speed of local network segment (10Base-T/100Base-TX Ethernet).
Rear Panel
1
Cam1 Analog Video Input of Composite Signal with BNC Connector
2
Cam2 Analog Video Input of Composite Signal with BNC Connector
3
Cam3 Analog Video Input of Composite Signal with BNC Connector
4
Cam4 Analog Video Input of Composite Signal with BNC Connector
5
Monitor Out
Analog Video Ouput of Composite Signal with BNC Connector
1.3 CONNECT NECESSARY CABLES The BNC cable for video input, Ethernet cable and power cable are necessary for previewing function. Make sure all cables are correctly and firmly connected.
1. Connect an analog video source (eg. CCD Camera) to the video server’s CAM1 ~ CAM4
(BNC connector). 2. Connect an analog monitor to the video server’s Monitor-Out
(BNC connector)
3. Connect the video server’s LAN port to an Ethernet hub (RJ45 connectors) 4. Connect a PC to the Ethernet hub (RJ45 connectors) 5. Connect the power adaptor to the video server (terminal block connector)
22
Quick Tour
This section guides you with a quick tour on this Quad video server
2.1 Configure the Quad Video Server 2.1.1 Make sure network environment Default IP of video server is 192.168.0.100. Please make sure the video server and your PC on the same network segment before running the installation.
Please set the settings as below. IP address: 192.168. 0.xxx Subnet mask: 255.255.255.
0
(NOTE: xxx should be a number from 1 to 254, but 100 is excepted.)
2.1.2 Open Internet Explorer with IP address This section describes how to configure the video server. The product administrator has unlimited access to all setup windows and normal users can only watch the live images. The video server is configured under a standard browser (Microsoft Internet Explorer 6.0 or above). Follow the procedures below to configure the video server. z
STEP1: Open a browser
z
STEP2: Enter the domain name or the IP address of the video server. The default IP address is “192.168.0.100”
z
STEP3: Enter the Account name (factory default: Admin) and the Password (factory default: 123456).
z
STEP4: Select the language of the video server user interface. You can select from English, Traditional Chinese, Simplified Chinese, Japanese and Spanish.
z
STEP5: Click the again.
button to login or click the
button to re-enter
Once successfully login, the “Main Setup page” will be displayed as below.
2.1.3 Preview the video
z
STEP1: Click Click the
to choose a display mode, such as quad video, or a single channel video.
[Apply] button to confirm the setting.
2.1.4 Set a new IP address
*Host Name : Enter a domain name. The default Host Name is ACTi. *Language : Language setting for Web Configurator after [Save Reboot]. Default setting is
English. *IP Address : The IP address of the LAN interface. The default IP address is 192.168.0.100. *Subnet Mask : The subnet mask of the LAN interface.The default subnet mask is 255.255.255.0 *Click
button
NOTE: Check with your MIS department, if Client PC and the video server are setting in different VLANs, please connect to WAN port.
NOTE: In your Client PC, please make sure the setting of Network Connections Type is set to Auto Negotation, since video server follows MII standard. Otherwise, you might not see the live video.
IMPORTANT: After the IP address is changed, please record this IP address. There is no way to connect to the video server if user forgets the new IP address.
2.1.5 Check Default Video Setting
NOTE: Please make sure the TV Input (NTSC / PAL) is meet your requirement, and click
button.
2.1.6 Click Save Reboot to restore all settings and please wait about 30 seconds for system reboot.
