Transcript
PHONES (044) 360-7-130 (050) 336-0-130 (063) 788-0-130 (067) 233-0-130 (068) 282-0-130
Internet store of autogoods
ICQ 294-0-130 597-0-130 SKYPE km-130
CAR RECEIVERS — Receivers • Media receivers and stations • Native receivers • CD/DVD changers • FM-modulators/USB adapters • Flash memory • Facia plates and adapters • Antennas • Accessories | CAR AUDIO — Car audio speakers • Amplifiers • Subwoofers • Processors • Crossovers • Headphones • Accessories | TRIP COMPUTERS — Universal computers • Model computers • Accessories | GPS NAVIGATORS — Portable GPS • Built-in GPS • GPS modules • GPS trackers • Antennas for GPS navigators • Accessories | VIDEO — DVR • TV sets and monitors • Car TV tuners • Cameras • Videomodules • Transcoders • Car TV antennas • Accessories | SECURITY SYSTEMS — Car alarms • Bike alarms • Mechanical blockers • Immobilizers • Sensors • Accessories | OPTIC AND LIGHT — Xenon • Bixenon • Lamps • LED • Stroboscopes • Optic and Headlights • Washers • Light, rain sensors • Accessories | PARKTRONICS AND MIRRORS — Rear parktronics • Front parktronics • Combined parktronics • Rear-view mirrors • Accessories | HEATING AND COOLING — Seat heaters • Mirrors heaters • Screen-wipers heaters • Engine heaters • Auto-refrigerators • Air conditioning units • Accessories | TUNING — Vibro-isolation • Noise-isolation • Tint films • Accessories | ACCESSORIES — Radar-detectors • Handsfree, Bluetooth • Windowlifters • Compressors • Beeps, loudspeakers • Measuring instruments • Cleaners • Carsits • Miscellaneous | MOUNTING — Installation kits • Upholstery • Grilles • Tubes • Cable and wire • Tools • Miscellaneous | POWER — Batteries • Converters • Start-charging equipment • Capacitors • Accessories | MARINE AUDIO AND ELECTRONICS — Marine receivers • Marine audio speakers • Marine subwoofers • Marine amplifiers • Accessories | CAR CARE PRODUCTS — Additives • Washer fluid • Care accessories • Car polish • Flavors • Adhesives and sealants | LIQUID AND OIL — Motor oil • Transmission oil • Brake fluid • Antifreeze • Technical lubricant
In store "130" you can find and buy almost all necessary goods for your auto in Kyiv and other cities, delivery by ground and postal services. Our experienced consultants will provide you with exhaustive information and help you to chose the very particular thing. We are waiting for you at the address
http://130.com.ua
13
0.
co
m .u a
USER MANUAL
Autogood products «130»
m .u a
Join the GoPro party at facebook.com/gopro to see
co
what other GoPro owners are capturing and sharing.
13
0.
Share your footage and join the GoPro movement!
Autogood products «130»
TABLE OF CONTENTS 4
Mounts + Accessories
5
HERO3+ Features
6
Camera LCD Status Screen
8
Camera Menu Flow Chart
9
Camera Software Updates
10
m .u a
Accessories
Basics Camera Modes Camera Settings Capture Settings
co
Set Up
10 13 20 31 35 43
Connecting to GoPro App
44
Storage/microSD™ Cards
45
System Requirements
46
Transferring Files
47
Playback
48
Battery
50
Important Warning Messages
53
Camera Housing
54
Using the Mounts
58
Customer Support
60
13
0.
Wi-Fi + Wi-Fi Remote
Autogood products «130»
WEAR IT. MOUNT IT. LOVE IT. FEATURED ACCESSORIES
HERO3+ ACCESSORIES Wrist Housing
m .u a
LCD Touch BacPac™
Standard Housing
13
0.
co
Rechargeable Battery
Battery BacPac™
Wi-Fi Remote
Dive Housing Lens Replacement Kit
Protective Lens + Covers
More HERO3+ accessories available at gopro.com The Frame
4
Autogood products «130»
SEE MORE AT GOPRO.COM
Chesty
Floaty Backdoor
Handlebar/Seatpost/ Pole Mount
Surfboard Mounts
Suction Cup
Vented Helmet Strap
m .u a
Helmet Front Mount
co
MOUNTS + ACCESSORIES
13
0.
Head Strap + QuickClip
Roll Bar Mount
Tripod Mounts
Anti-Fog Inserts
Jaws Flex Clamp Mount
Curved + Flat Adhesive Mounts
Side Mount
Camera Tethers
Dual Battery Charger
Autogood products «130»
5
13
0.
co
m .u a
HERO3+ FEATURES
1. Camera Status Lights (Red) 2. Shutter/Select Button 3. LCD Status Screen 4. Wi-Fi Status Lights (Blue ) 5. Power/Mode Button 6
6. Micro HDMI Port (Cable not included) 7. MicroSD Card Slot (SD card not included) 8. Mini-USB Port (Supports Composite A/C cable/3.5mm stereo mic adapter, not included)
Autogood products «130»
13
0.
co
m .u a
HERO3+ FEATURES
9. HERO Port 10. Battery Door 11. Wi-Fi On/Off Button 12. Audio Alert 13. Microphone
Autogood products «130»
7
CAMERA LCD STATUS SCREEN
m .u a
The LCD screen displays the following information about HERO3+ modes and settings:
1. Camera Modes/FOV (Field of View)
co
2. Capture Setting Modes (not shown)
3. Resolution/fps (Frames Per Second)
13
5. Counter
0.
4. Time Interval Settings: (not shown)
6. Time/Storage/Files 7. Battery Life
NOTE: The icons displayed above will vary depending on what mode your camera is in.
8
Autogood products «130»
CAMERA MENU FLOW CHART
0.
co
CAMERA SETTINGS
m .u a
MODES
WI-FI
13
CAPTURE SETTINGS
SET UP *Playback only appears in LCD Status Screen if camera is connected to a TV or LCD Touch BacPac™ (optional accessory, sold separately).
Autogood products «130»
9
CAMERA SOFTWARE UPDATES Slim housing closed Swapping housingfrom doors To get the latest features and best performance your HERO3+
camera, make sure you’re using the most current camera software. To check if software updates are available, visit: gopro.com/update.
GETTING STARTED
Slim housing remove camera
m .u a
USING YOUR HERO3+: BASICS
0.
co
1. Remove camera from housing
13
2. Remove camera side door and insert a microSD, microSDHC™ or microSDXC™ card into the card slot. A microSD card with a Class 10 speed rating is required. 3. Open camera back door, insert battery, close camera back door.
10
Autogood products «130»
Sli
USING YOUR HERO3+: BASICS 4. C harge the battery. The included lithium-ion battery comes partially charged. To charge, connect the included USB cable to camera and connect the other end of the cable to a power source such as a computer, GoPro Wall Charger or GoPro Auto Charger. No damage will occur to the camera or battery if used prior to a full charge. When camera is OFF and charging: • Red Camera Status Light will turn ON when camera is charging. • Red Camera Status Light will turn OFF when charging is complete.
m .u a
PRO TIP:
▶See BATTERY LIFE for more information.
co
CAMERA DEFAULT SETTINGS
0.
The HERO3+ Silver Edition camera powers up with the following default settings:
13
Video Resolution
PRO TIP:
960p60 fps
Photo Resolution
10MP
Burst Photo
10 photos in 1 second
Time Lapse
0.5 seconds
Wi-Fi
OFF
Want to change your VIDEO and PHOTO settings? ▶See SETTINGS menu to make changes.
Autogood products «130»
11
USING YOUR HERO3+: BASICS
co
m .u a
POWERING ON AND OFF
13
0.
To power ON: Press the Power/Mode Button . The red Status Indicator Lights flash three times and the Sound Indicator emits three beeps. To power OFF: Press and hold the Power/Mode Button . The red Status Indicator Lights flash several times and the Sound Indicator emits seven beeps.
PRO TIP:
Want to turn your HERO3+ into a “one-button” camera that automatically starts recording PHOTOS or VIDEOS once it turns ON? Set the camera to ONE BUTTON mode. ▶See ONE BUTTON mode for more information.
12
Autogood products «130»
USING YOUR HERO3+: CAMERA MODES OVERVIEW The HERO3+ features several camera modes. To cycle through the modes, press the Power/Mode Button
. The modes will appear in the following order: Record Video
PHOTO
Capture a single Photo
BURST PHOTO
Capture up to 10 Photos in one second Capture a series of Photos at timed intervals
co
TIME LAPSE
m .u a
VIDEO
0.
SETTINGS
Playback Video and Photos. Appears only if camera is connected to a TV or LCD Touch BacPac™ (optional accessory, sold separately).
13
PLAYBACK
Adjust camera Settings
PRO TIP:
Use BURST PHOTO to capture fast-moving subjects.
▶See PLAYBACK for more information.
Autogood products «130»
13
USING YOUR HERO3+: CAMERA MODES VIDEO To record Video, verify the camera is in Video mode. If the Video icon on your camera’s LCD screen is not showing, press the Power/Mode Button repeatedly until it appears.
m .u a
To start recording: Press the Shutter/Select Button . The camera will emit one beep and the red Camera Status Lights will flash while recording.
co
To stop recording: Press the Shutter/Select Button . The red Camera Status Lights flash three times and the camera emits three beeps to indicate recording has stopped. The HERO3+ automatically stops recording when the memory card is full or the battery is out of power. Your video will be saved before the camera powers OFF.
13
0.
▶See VIDEO mode for instructions on how to change resolution settings.
14
Autogood products «130»
USING YOUR HERO3+: CAMERA MODES PHOTO To capture a Photo, verify the camera is in Photo mode. If the Photo icon on your camera’s LCD is not showing, press the Power/Mode Button repeatedly until it appears.
. The camera beeps two times
m .u a
To take a photo: Press and release the Shutter/Select Button and the red Camera Status Lights flash.
13
0.
co
▶See PHOTO modes for instructions on how to change resolution s
Autogood products «130»
15
USING YOUR HERO3+: CAMERA MODES BURST PHOTO In Burst Photo mode your camera takes multiple photos in short time intervals— 3 photos /1 second, 5 photos /1 second and 10 photos /1 second.
m .u a
To capture a Burst Photo series, verify the camera is in Burst Photo mode. If the Burst Photo icon on your camera’s LCD screen is not showing, press the Power/Mode Button repeatedly until it appears. To take a Burst Photo series:
Press the Shutter/Select Button . The red Camera Status Lights flash and the camera beeps multiple times.
13
0.
co
▶See BURST PHOTO for instructions on how to change the interval settings.
16
Autogood products «130»
USING YOUR HERO3+: CAMERA MODES TIME LAPSE Time Lapse mode captures a series of photos at 0.5, 1, 2, 5, 10, 30 or 60 second intervals.
m .u a
To capture a Time Lapse series, verify the camera is in Time Lapse mode. If the Time Lapse icon is not showing on your camera’s LCD screen, press the Power/Mode Button repeatedly until it appears. To take Time Lapse: Press the Shutter/Select Button . The camera initiates countdown and the red Camera Status Lights flash each time a Photo is taken.
co
To stop Time Lapse: Press the Shutter/Select Button . The red Camera Status Lights flash three times and the camera emits three beeps to indicate that Time Lapse has stopped.
13
0.
▶See TIME LAPSE for instructions on how to change the interval settings.
Autogood products «130»
17
USING YOUR HERO3+: CAMERA MODES SETTINGS The Settings menu allows you to adjust a variety of camera settings including: Video Resolution Photo Resolution
Continuous Photo
m .u a
Time Lapse Burst Photo
13
0.
co
▶See SETTINGS menu to make changes, learn how to navigate menu options and read more details on each setting.
18
Autogood products «130»
USING YOUR HERO3+: CAMERA MODES PLAYBACK Playback Video and Photos by connecting your HERO3+ to a TV (requires Micro HDMI, Composite or Combo Cable, sold separately). You can also playback Video and Photos on the LCD Touch BacPac™ (optional accessory, sold separately). The Playback icon appears only if camera is connected to a TV or LCD Touch BacPac.
13
0.
co
m .u a
▶See PLAYBACK for more information on viewing your VIDEOS and PHOTOS.
Autogood products «130»
19
CAMERA SETTINGS SETTINGS To enter the Settings menu: 1. Verify the camera is in the Settings mode. If the Settings icon on your camera’s LCD screen is not showing, press the Power/Mode Button repeatedly until it appears.
3. Use the Power/Mode Button options.
to enter Settings menu
m .u a
2. Press the Shutter/Select Button
.
to cycle through the various Settings
4. Press the Shutter/Select Button
to select desired option.
20
If at any time you wish to exit from the Settings menu, press and hold the Shutter/Select Button for two seconds.
13
PRO TIP:
0.
co
5. To exit, hold down the Shutter/Select Button for two seconds or cycle through to and press the Shutter/Select Button .
Autogood products «130»
CAMERA SETTINGS VIDEO RESOLUTION/ FPS/FOV MODES You can change Resolution, fps (frames per second) and FOV (field of view) in the Video mode menu. You can also turn Auto Low Light mode ON/OFF. Once in the Settings menu: 1. Press the Shutter/Select Button
.
m .u a
to enter
2. Use the Power/Mode Button
to cycle through options.
3. Press the Shutter/Select Button
to enter desired menu.
to cycle through each sub-menu option to select it.
co
4. Use the Power/Mode Button and the Shutter/Select Button
5. To change additional options, repeat step 4.
13
0.
6. To exit, hold down the Shutter/Select Button for two seconds or cycle through to and press the Shutter/Select Button to select it.
Autogood products «130»
21
CAMERA SETTINGS The HERO3+ Silver Edition offers the following Video Capture modes: NTSC fps
PAL fps
Field of View (FOV)
Screen Resolution
1080p
60
50
Ultra Wide, Medium, Narrow
1920x1080 16:9
1080p
30
25
Ultra Wide, Medium, Narrow
1920x1080 16:9
960p
60
50
Ultra Wide
1280x960 4:3
960p
30
25
Ultra Wide
1280x960 4:3
720p
120
100
720p
60
co
Ultra Wide, Medium, Narrow
1280x720 16:9
Ultra Wide Medium, Narrow
1280x720 16:9
0. 50
13
720p
m .u a
Video Resolution
30
25
Ultra Wide, Medium, Narrow
1280x720 16:9
WVGA
120
100
Ultra Wide
848x480 16:9
WVGA
60
50
Ultra Wide
848x480 16:9
22
Autogood products «130»
CAMERA SETTINGS Best Use
1080p
1080p60 is great for all shots, as high resolution and frame rate yield stunning results. Try 1080p30 when shooting with a tripod or for fixed-mounted shots.
960p
Use for body-mounted shots. Provides the largest viewing area and smooth results for high-action capture. Use 960p60 when slow motion is desired—use 960p30 when shooting in low-light conditions.
720p
Best resolution and frame rate for handheld shots. Use 720p120 or 720p60 when slow motion is desired. Use 720p30 in low-light conditions.
13
0.
co
m .u a
Video Resolution
WVGA
For smaller data files, this is standard definition resolution. Also good when slow motion is desired.
Autogood products «130»
23
CAMERA SETTINGS PHOTO RESOLUTION MODES
Field of View (FOV)
10MP
Wide (Default)
7MP
Wide
5MP
Medium
13
0.
co
Photo Resolution
m .u a
The HERO3+ can capture photos at 10MP, 7MP and 5MP resolutions. Any change to photo resolution also affects photos captured in Photo, Burst Photo and Time Lapse modes.
24
Autogood products «130»
CAMERA SETTINGS OPTIONS Burst Photo mode captures a series of Photos when the Shutter/Select Button is pressed. Photos can be captured at the following rates:
5 photos in 1 second
m .u a
3 photos in 1 second
10 photos in 1 second (Default)
co
TIME LAPSE
13
0.
Several time interval options are available for Time Lapse mode, including 0.5, 1, 2, 5, 10, 30 and 60 seconds.
Autogood products «130»
25
CAMERA SETTINGS CAPTURE SETTINGS MENU Capture Settings allows you to adjust the following advanced capture options: Camera Orientation
m .u a
Spot Meter Looping Video
13
0.
co
▶See CAPTURE SETTINGS section for a complete list of capture options.
26
Autogood products «130»
CAMERA SETTINGS SET UP MENU The Set Up menu allows you to adjust the following camera settings: Default mode at Power Up
NTSC/PAL On Screen Display
m .u a
One Button Mode
Camera Status Lights
co
Sound Indicator
0.
Month/Day/Year/Time
13
▶See SET UP MENU section for a complete list of set up options.
Autogood products «130»
27
CAMERA SETTINGS WIRELESS CONTROLS
m .u a
The camera’s built-in Wi-Fi allows you to connect to the Wi-Fi Remote (optional accessory, sold separately) or smartphone/tablet via the GoPro App. When Wi-Fi is ON, a Wi-Fi status icon will appear on the camera’s LCD Status Screen and the blue Wi-Fi Status Lights will blink intermittently. When you turn OFF the Wi-Fi, the Wi-Fi Status Lights flash seven times. To turn Wi-Fi ON/OFF:
to turn Wi-Fi ON/OFF. The most recently Press the Wi-Fi On/Off Button used Wi-Fi mode will be active when Wi-Fi is ON.
co
▶See WIRELESS CONTROLS section for a complete list of wireless functions
13
0.
NOTE: Your camera cannot connect to the Wi-Fi Remote (optional accessory, sold separately) and GoPro App at the same time.
28
Autogood products «130»
CAMERA SETTINGS DELETE Delete the last file or all files and format the memory card. During delete LAST or ALL, the Camera Status Lights blink until operation is complete. CANCEL (Default)
m .u a
LAST ALL
(Formats SD card)
To delete LAST or ALL:
co
on your 1. Verify the camera is in Settings mode. If the Settings icon camera’s LCD screen is not showing, press the Power/Mode Button repeatedly until it appears. 2. Press the Shutter/Select Button
13
0.
3. Use the Power/Mode Button the Trash .
4. Press the Shutter/Select Button 5. Use the Power/Mode Button
to enter Settings menu
.
to cycle through Settings to locate to enter Delete.
to cycle through options.
6. Select highlighted option by pressing the Shutter/Select Button
.
7. To exit, hold down the Shutter/Select Button for two seconds or cycle through to and press the Shutter/Select Button . PRO TIP:
Use caution—by selecting ALL, the memory card will be formatted, deleting every file on your SD card.
Autogood products «130»
29
CAMERA SETTINGS EXIT From the screen, press the Shutter/Select Button Settings menu.
m .u a
If at any time you wish to exit from the SETTINGS menu, press and hold the Shutter/Select Button for two seconds.
13
0.
co
PRO TIP:
to exit the
30
Autogood products «130»
CAPTURE SETTINGS CAPTURE SETTINGS To enter the Capture Settings menu: 1. Verify the camera is in Settings mode. If the Settings icon on your camera’s LCD screen is not showing, press the Power/Mode Button repeatedly until it appears. 2. Press the Shutter/Select Button
to enter the Settings menu
m .u a
3. Use the Power/Mode Button Capture Settings menu .
4. Press the Shutter/Select Button
to enter Capture Settings.
co
5. Use the Power/Mode Button
to locate the desired option to change. to select the desired option.
0.
6. Press the Shutter/Select Button
.
to cycle through Settings to locate the
13
7. Some options have a sub-menu. Use the Power/Mode Button to cycle through the sub-menus. 8. Press the Shutter/Select Button
to select a highlighted option.
9. To exit, hold down the Shutter/Select Button for two seconds or cycle through to and press the Shutter/Select Button to select it.
Autogood products «130»
31
CAPTURE SETTINGS You can customize the way your HERO3+ camera captures Video and Photos in the Capture Settings menus, such as Upside Down, Looping Video and White Balance. UPSIDE DOWN
m .u a
Mounting your HERO3+ Upside Down but wish the files to appear upright when viewing or editing? This setting eliminates the need to flip your Video or Photos after recording. Camera right side up (Default)
0.
SPOT METER
co
Camera upside down
OFF
13
Turn on Spot Meter when filming from within a dark space pointing the camera into a brighter setting, such as filming the outdoors from within a car. When Spot Meter is set to ON, appears in the LCD window. (Default)
ON
32
Autogood products «130»
CAPTURE SETTINGS LOOPING VIDEO Looping Video mode allows you to record a continuously looping video that button to stop it. overwrites itself until you press the Shutter/Select Button Looping Video options inlcude: (Default)
Max video
Camera records until memory card is full, then overwrites with a new video.
5 min video
Camera records for 5 minutes, then begins a new video, progressively overwriting the previous 5 minute video.
20 min video
Camera records for 20 minutes, then begins a new video, progressively overwriting the previous 20 minute video.
60 min video
Camera records for 60 minutes, then begins a new video, progressively overwriting the previous 60 minute video.
13
0.
co
m .u a
OFF
120 min video
PRO TIP:
Camera records for 120 minutes, then begins a new video, progressively overwriting the previous 120 minute video.
Multiple chapter files are written to your memory card. This allows for small segments of content to be overwritten during loop recording. When viewing on a computer screen, you will see separate files for each time segment. Use video editing software if you wish to combine files into a longer video.
Autogood products «130»
33
CAPTURE SETTINGS EXIT From the EXIT screen, press the Shutter/Select Button Capture Settings menu.
m .u a
If at anytime you wish to exit from the CAPTURE SETTINGS MENU, press and hold the Shutter/Select Button for two seconds.
13
0.
co
PRO TIP:
to exit the
34
Autogood products «130»
SET UP SET UP To enter the Set Up menu:
m .u a
1. Verify the camera is in Settings mode. If the Settings icon on your camera’s LCD screen is not showing, press the Power/Mode Button repeatedly until it appears. 2. Press the Shutter/Select Button 3. Use the Power/Mode Button Set Up menu .
to enter the Settings menu
.
to cycle through Settings to locate the to enter Set Up.
to locate the desired option to change.
6. Press Shutter/Select Button
to select the desired option.
0.
co
4. Press Shutter/Select Button 5. Use the Power/Mode Button
13
7. To exit, hold down Shutter/Select Button for two seconds or cycle through to and press Shutter/Select Button to select it.
Autogood products «130»
35
SET UP DEFAULT MODE AT POWER UP You can set the camera’s Default mode of power up to any of the following modes: VIDEO (default)
m .u a
PHOTO BURST PHOTO
13
0.
co
TIME LAPSE
36
Autogood products «130»
SET UP ONE BUTTON With One Button mode selected, the camera automatically begins recording when powering the camera ON. One Button mode can be configured to start in Video or Time Lapse. OFF
(Default)
m .u a
ON
To turn One Button mode ON:
co
on your 1. Verify the camera is in Settings mode. If the Settings icon camera’s LCD screen is not showing, press Power/Mode Button repeatedly until it appears. 2. Press the Shutter/Select Button
0.
3. Use the Power/Mode Button . the Set Up menu
13
4. Press Shutter/Select Button 5. Use the Power/Mode Button . One Button mode 6. Press the Shutter/Select Button 7. Use the Power/Mode Button 8. Press the Shutter/Select Button
to enter the Settings menu
.
to cycle through Settings to locate to enter Set Up. to cycle through to locate to enter One Button menu. to cycle through options. to select a highlighted option.
for two seconds or cycle 9. To exit, hold down the Shutter/Select Button and press the Shutter/Select Button to select it. through to The next time you power your camera ON, it will begin recording in its Default Power Up Mode. To stop recording, push and hold for two seconds. 37
Autogood products «130»
SET UP ONE BUTTON MODE (continued) To exit One Button mode: 1. Power camera ON. 2. Press and hold the Shutter/Select Button in the LCD window.
4. Use the Power/Mode Button 5. Press the Shutter/Select Button
shows
to enter.
m .u a
3. Press the Shutter/Select Button
until
to highlight OFF. to select it.
co
6. To exit, hold down the Shutter/Select Button for two seconds or cycle through to and press the Shutter/Select Button .
0.
To stop the capture process (VIDEO or TIME LAPSE) when in ONE BUTTON, press and hold the Shutter/Select Button for two seconds. You will return to the ONE BUTTON menu where you can turn ONE BUTTON mode OFF.
13
PRO TIP:
NOTE: One Button mode is disabled when connected to Wi-Fi Remote (optional accessory, sold separately) or GoPro App.
38
Autogood products «130»
SET UP NTSC / PAL The NTSC and PAL settings govern Video recording frame rate and playback when viewing Video on a TV/HDTV. Select NTSC when viewing a TV/HDTV in North America. Select PAL if viewing on a PAL TV/HDTV (most televisions outside of North America) or if viewing on a PAL TV/HDTV in any region. NTSC (Default)
m .u a
PAL
1080p/60 fps
1080p/50 fps
1080p/30 fps
1080p/25 fps
960p/60 fps
960p/50 fps 960p/25 fps
co
960p/30 fps 720p/120 fps 720p/30 fps
0.
720p/60 fps
13
WVGA/120 fps WVGA/60 fps
720p/100 fps 720p/50 fps 720p/25 fps WVGA/100 fps WVGA/50 fps
ONSCREEN DISPLAY To display or hide the recording icons and file information on Video or the viewing screen during playback, turn Onscreen Display (OSD) OFF or ON. OFF ON
(Default)
Autogood products «130»
39
SET UP CAMERA STATUS LIGHTS
SOUND INDICATOR
m .u a
Keep all four Camera Status Lights active, only two active (front and back) or turn OFF all lights. 4 (Default) 2 OFF
13
0.
co
You can adjust volume or turn OFF the Sound Indicator. 100% (Default) 70% OFF
MANUAL POWER OFF The HERO3+ can be configured to automatically power OFF after a specific period of inactivity (when no Videos or Photos are being taken and no buttons have been pressed). MANUAL (Default) 60 sec 120sec 300 sec 40
Autogood products «130»
SET UP MONTH / DAY / YEAR / TIME Set the HERO3+ clock to ensure Video and Photo files are saved with the correct date and time. To change Month/Day/Year/Time:
m .u a
1. V erify the camera is in Settings mode. If the Settings icon on your camera’s repeatedly until LCD screen is not showing, press the Power/Mode Button it appears. 2. Press the Shutter/Select Button 3. Use the Power/Mode Button . the Set Up menu
.
to enter the Set Up menu.
co
4. Press the Shutter/Select Button
to enter the Settings menu
to cycle through Settings to locate
5. Use the Power/Mode Button
0.
6. Press the Shutter/Select Button Month (MM) will be highlighted.
13
7. Press the Shutter/Select Button 8. Use the Power/Mode Button is highlighted. 9. Press the Shutter/Select Button
to locate the Month/Day/Year/Time menu
.
to enter Month/Day/Year/Time menu;
to access the list of months (1 to 12). to cycle through list until desired selection to select.
10. To advance to the next option, press the Shutter/Select Button
.
11. Repeat steps 7, 8 and 9 to make selections for day (DD), year (YY), hour (HH) and minutes (MM). for two seconds or cycle 12. To exit, hold down the Shutter/Select Button and press the Shutter/Select Button . through to NOTE: If the battery is removed from the camera for an extended period of time Month/Day/Year/Time will need to be set again.
Autogood products «130»
41
SET UP EXIT From the EXIT screen, press the Shutter/Select Button Set Up menu.
m .u a
If at anytime you wish to exit from the SET UP menu, press and hold the Shutter/Select Button for two seconds.
13
0.
co
PRO TIP:
to exit the
42
Autogood products «130»
WI-FI + WI-FI REMOTE WIRELESS CONTROLS The built-in Wi-Fi allows your HERO3+ camera to connect to the Wi-Fi Remote (optional accessory, sold separately) or to the GoPro App using a smartphone or tablet. To turn Wi-Fi ON/OFF via the Wi-Fi On/Off Button
:
m .u a
Press the Wi-Fi On/Off Button to turn Wi-Fi ON/OFF. When turning Wi-Fi ON, the Wi-Fi mode will be set to the most recently used mode. WI-FI REMOTE (SOLD SEPARATELY)
0.
co
Use the Wi-Fi Remote (sold separately) to control up to 50* cameras remotely from distances of up to 600’/180m. The Wi-Fi Remote is wearable and waterproof to 10’/3m. For instructions on pairing and connecting the Wi-Fi Remote to the camera, please see the Wi-Fi Remote User Manual included with the remote.
13
*Actual results may vary depending on presence of wireless interference.
Autogood products «130»
43
CONNECTING TO GOPRO APP USING YOUR HERO3+ WITH THE GOPRO APP (FREE) The GoPro App lets you control your camera remotely using a smartphone or tablet. Features include full camera control, live preview, playback and sharing of select content and more.* Follow these steps to connect your HERO3+ to the GoPro App.
2. Press the Power/Mode Button
m .u a
1. Download the GoPro App to your smartphone or tablet at the Apple App Store, Google Play or Windows Phone marketplace. to power camera ON.
twice, then press the 3. Press the Wi-Fi On/Off Button Shutter/Select Button to enter Wi-Fi menu .
co
to cycle through options, 4. Use the Power/Mode Button to select GoPro App. press the Shutter/Select Button
0.
5. In your smartphone’s or tablet’s Wi-Fi network settings, connect to the camera’s Wi-Fi network. The network name will begin with “GOPRO-BP-”, followed by a series of letters/numbers.
13
6. Enter the password “goprohero”. (This is the camera’s default password. You can customize the password at gopro.com/update. If you’ve already customized the password, enter that password instead of “goprohero”.) 7. Open the GoPro App on your smartphone or tablet. You will now be able to control the camera with your smartphone or tablet plus view, playback and share select content.* PRO TIP:
See what your HERO3+ sees by viewing it on your smartphone or tablet’s screen.
*For device compatibility, please see gopro.com. 44
Autogood products «130»
STORAGE/MICROSD CARDS The HERO3+ camera is compatible with 4GB, 8GB, 16GB, 32GB and 64GB capacity microSD, microSDHC and microSDXC memory cards. You must use a microSD card with a Class 10 speed rating. GoPro recommends using brand name memory cards for maximum reliability in high-vibration activities. To remove microSD card:
m .u a
To insert microSD card:
co
1. Slide memory card into card slot with label facing front of camera.
2. Card will spring out far enough to be removed.
13
0.
2. The card will click into place when fully inserted.
1. Place fingernail against edge of memory card and lightly press further into camera.
PRO TIP:
Use care when handling memory cards. Avoid liquids, dust and debris. As a precaution, turn off the camera before inserting or removing the card. Check manufacturer guidelines regarding use in acceptable temperature ranges.
Autogood products «130»
45
SYSTEM REQUIREMENTS The HERO3+ camera is compatible with Microsoft® XP (Service Pack 2) or later and Mac OS X 10.4.11 or later. MAC Mac OS® X 10.4.11 or later
3.2GHz Pentium 4 or faster
2.0GHz Intel Core Duo or faster
DirectX 9.0c or later Minimum 1GB of system RAM
Video card with minimum 128MB of RAM
0.
Want to see your Video and Photos on the big screen? Connect your HERO3+ directly to your TV/HDTV using a Micro HDMI Cable, Composite Cable or Combo Cable (optional accessories, sold separately).
13
PRO TIP:
Minimum 1GB of system RAM
co
Video card with minimum 256MB of RAM
m .u a
WINDOWS Windows XP (Service Pack 2 or later) or Vista
46
Autogood products «130»
TRANSFERRING FILES TO TRANSFER VIDEO AND PHOTO FILES TO A COMPUTER On a PC: 1. Connect the camera to the computer using included USB cable. 2. Press the Power/Mode Button
to turn ON the camera.
3. Double click “My Computer” and locate “Removable Disk”.
m .u a
4. If “Removable Disk” is not showing, close “My Computer” folder and reopen it. The “Removable Disk” icon should appear. 5. Double click “Removable Disk” icon. 6. Double click “DCIM” folder icon.
7. Double click “100GOPRO” icon to view all Photo and Video files.
co
8. Copy files to the computer or external hard drive.
0.
On a Mac: 1. Connect the camera to Mac using included USB cable. to turn ON the camera.
13
2. Press the Power/Mode Button
3. Icon will appear on desktop. Double click the icon to access files. 4. Copy files to computer or external hard drive.
Autogood products «130»
47
PLAYBACK TO VIEW VIDEOS AND PHOTOS Videos and Photos can be viewed on a TV/HDTV or the LCD Touch BacPac (optional accessory, sold separately). PLAYBACK ON TV/HDTV To browse Videos and Photos:
m .u a
1. Plug the camera into a TV/HDTV with a Micro HDMI Cable, Composite Cable or Combo Cable (optional accessories). 2. Turn camera ON.
co
3. On your camera, press the Power/Mode Button Playback . Press the Shutter/Select Button
to cycle to .
0.
4. HERO3+ displays thumbnail previews of all Videos and Photos on the SD card. Photo sets taken in Continuous Photo, Photo Burst and Time Lapse display the first Photo in a series.
13
5. While in thumbnail preview, use the Power/Mode Button to cycle through thumbnails. Press the Shutter/Select Button to view. 6. Use and to navigate backward and forward to see more media files on your memory card. 7. Depending on whether you are viewing Videos or Photos, different control options will appear. Use the Power/Mode Button and the Shutter/Select Button to navigate. NOTE: Burst Photo and Time Lapse files will display the first Photo in the series. To view all Photos in a series, use the Power/Mode Button to select View and press the Shutter/Select Button . 48
Autogood products «130»
PLAYBACK PLAYBACK ON LCD TOUCH BACPAC (SOLD SEPARATELY) Playback using the LCD Touch BacPac™ follows a similar process/procedure as described with a few slight variations.
13
0.
co
m .u a
▶See the LCD Touch BacPac User Manual for more information.
Autogood products «130»
49
BATTERY MAXIMIZING BATTERY LIFE
m .u a
To maximize battery life, turn Wi-Fi OFF. To maximize battery life when shooting longer-duration activities, turn OFF or detach the LCD Touch BacPac™ (optional accessory, sold separately). Extreme cold temperatures may decrease battery life. To maximize battery life in cold conditions, keep camera in a warm place prior to use. Shooting with Protune mode turned ON will increase power consumption.
13
0.
co
*Based on GoPro engineering testing. Actual performance may vary based on settings, environmental conditions, wireless connectivity and other factors. Maximum battery capacity will normally decrease with time and use.
50
Autogood products «130»
BATTERY CHARGING THE BATTERY The battery icon displayed in the camera’s LCD will blink when the battery drops below 10%. If recording is occurring when battery reaches 0%, the camera will save the file and power OFF. To charge the battery:
m .u a
1. Connect the camera to a computer or USB power supply (such as the GoPro Wall Charger or GoPro Auto Charger).
co
2. The red Status Indicator Light remains ON while the battery is charging.
13
0.
3. The red Status Indicator Light will turn OFF when the battery is fully charged.
The battery will charge to 80% in one hour and 100% in two hours when using GoPro’s 1000mAh USB-compatible Wall or Auto Charger. Other chargers may charge at a slower rate. You can also charge the battery outside the camera using the Dual Battery Charger (optional accessory, sold separately). No damage will occur to the camera or the battery if used prior to full charge. Spare batteries and additional charging accessories are available at: gopro.com.
Autogood products «130»
51
BATTERY USING THE CAMERA WHILE CHARGING You can capture Video and Photos while charging the camera’s battery. Simply plug the camera into a computer, any USB charging devices, or for best results, the GoPro Auto or Wall Chargers using the included USB Cable. Performance of non-GoPro chargers cannot be guaranteed.
m .u a
REMOVING THE BATTERY FROM THE CAMERA The HERO3+ battery is designed to have a tight fit to maximize reliability in high-vibration activities.
13
0.
co
To remove the battery:
1. Remove the battery door by placing your thumb in the indentation in the battery door (on the back of the camera) and sliding it to the left. 2. Allow the door to pop out. Grasp the battery pull-tab and remove from the camera.
52
Autogood products «130»
IMPORTANT WARNING MESSAGES MICROSD CARD MESSAGES No card present. The camera requires a microSD, microSDHC or microSDXC card to record Video or take Photos.
SD FULL
Card is full. Delete files or swap card.
SD ERROR
Camera unable to access card.
m .u a
NO SD
FILE REPAIR ICON ON THE LCD
co
If you see the File Repair icon on the LCD screen, your Video file was corrupted during recording. Press any button and the camera will repair the file.
0.
TEMPERATURE WARNING ICON ON THE LCD
13
The Temperature Warning icon will appear on the LCD when the camera has become too hot and needs to cool down. Simply let it sit and cool before attempting to use it again. Your camera will not allow itself to overheat—do not worry, no damage has occurred.
Autogood products «130»
53
Slim housing closed
Swapping housing doors
CAMERA HOUSING ASSEMBLING THE CAMERA HOUSING To remove camera from housing: 1. Lift front of latch up to disengage from camera housing. 2. Pivot latch backward and pull up to release backdoor.
Slim housing remove camera
co
To secure camera in housing:
m .u a
3. Pull open housing backdoor and remove camera.
1. Open housing and drop camera into position.
0.
2. Close housing backdoor.
13
3. Pivot hinged arm backwards and hook lip of latch into grooved top of housing backdoor. Slim housing insert camera 4. Push latch down to snap into place.
54
Autogood products «130»
CAMERA HOUSING
m .u a
Your HERO3+ camera housing comes with two types of backdoors— Skeleton (non-waterproof) and Standard (waterproof).
Standard Backdoor
The Standard Backdoor makes the housing waterproof to 131’/40m. Use this door when you need to protect the camera from water and other environmental hazards.
13
0.
co
Skeleton Backdoor
The Skeleton Backdoor (non-waterproof) provides better sound quality by allowing more sound to reach the camera’s microphone. It also reduces wind noise at speeds up to 100mph when mounted on helmets, motorcycles, bikes and other fast-moving vehicles. Use this backdoor only when sand, excessive dirt/dust and water damage is not a risk. This backdoor is also recommended for use inside vehicles.
PRO TIP:
Apply Rain-X or a similar anti-beading solution to the camera housing lens to prevent water spots from forming when using your camera in rain or water. When Rain-X is not available, periodically licking your lens is a good backup solution. Trust us, it works.
Autogood products «130»
55
mb Screw + Slim housing = Complete Unit
CAMERA HOUSING
SWAPPING HOUSING DOORS You can switch the Backdoor of your HERO3+ camera to suit your activity and shooting conditions. To change backdoor:
co
m .u a
Swapping housing doors
0.
1. Open the Backdoor of the housing so that it is hanging Slimdownwards. housing insert camera
13
2. Pull downwards on the Backdoor until it snaps free from the hinge. 3. Line up replacement Backdoor into the hinge opening. 4. Push upwards on the Backdoor until it clicks into place.
56
Autogood products «130»
CAMERA HOUSING PREVENTING WATER DAMAGE TO YOUR CAMERA The rubber seal that lines the camera housing forms a waterproof barrier that protects your HERO3+ in wet and underwater conditions. Keep the camera housing’s rubber seal clean—a single hair or grain of sand can cause a leak and damage your camera.
m .u a
After every use in salt water, rinse the outside of the camera housing with non-salt water and dry. Not doing this can eventually cause corrosion of the hinge pin and salt buildup in the seal, which can cause failure.
co
To clean the seal, rinse in fresh water and shake dry (drying with a cloth may cause lint to compromise the seal). Re-install the seal into the grooves in the backdoor of the camera housing.
13
0.
WARNING: Failure to follow these steps each time you use your HERO3+ can result in leaks that may damage or destroy your camera. Your warranty does not cover water damage resulting from user error.
Autogood products «130»
57
USING THE MOUNTS ATTACHING YOUR CAMERA TO MOUNTS To attach your HERO3+ camera to a mount, you will need a Quick Release Buckle, thumb screw or hardware depending on the mount you are using.
Quick Release Buckle
Thumb Screw
Housing
Complete Unit
Swapping housing doors
co
Slim housing closed
m .u a
Quick For Release + Thumb Screw visit: + Slim housing = Complete Unit more Buckle information on mounts, gopro.com/support.
USING CURVED + FLAT ADHESIVE MOUNTS
13
0.
The Curved + Flat Adhesive Mounts make it easy to attach the camera to curved and flat surfaces of helmets, vehicles and gear. Using the Quick Release Buckle, the assembled camera housing can be clicked on and off the secured Curved or Flat Adhesive Mounts.
Slim ho
Slim housing remove camera
Flat Adhesive Mount
58
Curved Adhesive Mount
Autogood products «130»
USING THE MOUNTS ATTACHING ADHESIVE MOUNTS Apply to clean surface only. Wax, oil, dirt or other debris will reduce adhesion, which can result in a weak bond and risk of losing camera should connection fail.
PRO TIPS:
m .u a
Attach mount in room temperature conditions. Mount’s adhesive will not bond properly if applied in cold or damp environments to cold or damp surfaces, or if the surface is not room temperature.
co
Adhesive mounts should only be mounted to smooth surfaces; porous or textured surfaces will not enable a proper bond. When applying mount, firmly press into place and ensure full contact over entire surface.
0.
For best results, attach the mount 24 hours prior to use.
13
▶See: gopro.com/support for more information on mounts. Locking Plug
Using the HERO3+ in high impact sports such as surfing or skiing where significant impact may occur? Use the special Locking Plug which securely locks the Quick Release Buckle fingers into place, helping prevent accidental housing release from the mount. The circular ring fits over the thumbscrew and acts as a leash to prevent dropping or losing the locking plug.
Autogood products «130»
59
m .u a
CUSTOMER SUPPORT
13
0.
co
GoPro is dedicated to providing the best possible service. To reach GoPro Customer Support, visit gopro.com/support.
60
Autogood products «130»
