Transcript
Mini Storage Tower Overview
Addonics T E C H N O L O G I E S
Storage Tower MST4IDEU2, MST4ML, MST5X1PM, MST5XHPM, MST4ESA, MST-W MST4IDEU2-B, MST4ML-B, MST5X1PM-B, MST5XHPM-B, MST4ESA-B, MST-B
User’s Guide Version 1.0
FCC Warning Statement This equipment has been tested and found to comply with the limits for a class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try and correct the interference by one or more of the following suggestions. Reorient or relocate the receiving antenna Increase the distance between the equipment and the receiver Connect the equipment to a different power outlet other than the one where receiver is connected Consult a certified television or radio technician
Different Storage Devices placed inside the Mini Storage Tower
Removing Cover of Mini Storage Tower
Hardware Installation: A. MST4IDEU2:
Step 1 Loosen the 3 screws at the back of the tower using a Philips screwdriver by turning counter-clockwise.
Factory Settings: Mini Storage Tower with JBOD USB 2.0 adapter (AD4IDEU2) installed NOTE: If you are connecting 4 hard drives, for each of the two IDE ports, you need to set your IDE hard drives as master and slave. If you are connecting only one hard drive, on one IDE channel, you need to set it up as master. The end of the IDE ribbon cable is where you connect the master hard drive and the middle connector is for the slave.
Step 2 Separate the metal casing of the storage tower from the housing by lifting up the casing as shown on the photo.
Cable connections: • 2 12" UDMA IDE cable (AA2IDE80-12), • 4-pin floppy power connector for JBOD USB2.0 power • Power LED • Four hard drive activity LED
B. MST5X1PM:
C. MST5XHPM:
Factory Settings:
Factory Settings: Mini Storage Tower with one 5X1 Port Multiplier (AD5SAPM-E) installed
Cable connections: • 4 internal SATA data cable • 4-pin floppy power connector for port multiplier power • Power LED • Four hard drive activity LED
Mini Storage Tower with one 5X1 Port Multiplier (AD5SAHPM-E) installed
Cable connections: • 4 internal SATA data cable • 4-pin floppy power connector for port multiplier power • Power LED • Four hard drive activity LED
Floppy-type power connector
Floppy-type power connector
EMSC EMSD
SATA connectors for connection to up to 5 SATA hard drives
Drive Activity LEDs
SATA connectors for connection to up to 5 SATA hard drives
D. MST4ML: Factory Settings: Mini Storage Tower with 4SATA Multilane connector (AD4SAML) installed.
Note: You need to install the SiI4726 Manager on your system to configure RAID sets. RAID configuration is programmed by connecting the hardware port multiplier: • to one of Addonics’ SATA controllers that has SIL3124 or SIL3132 chip set. • via USB 2.0 connection (optional Addonics eSATA-USB adapter is required) After RAID configuration, it is compatible with any SATA controller (RAID or non RAID) Software Installation for SiI4726 Manager A. From the CD start-up menu select SATA RAID Utilities > Other SATARAID Utilities > Windows 2000/XP/2003/Vista. B. Unzip the file SiI_4726_Manager_V4.0.0.9.zip on your drive. The folder name would be SiI4726. C. To install SiI4726 Manager, double click setup.exe In SiI4726 Manager, all the drives connected to the AD5SAHPM-E will show up. For a complete User’s Guide of SiI4726 refer to our website. Support > User Guides > SiI4726 Manager User Manual V.26
Cable connections: • 4 internal SATA data cable • 4-pin floppy power connector for port multiplier power • Power LED Note: Hard drive LED activity lights does not function for this model
E. MST4ESA:
Storage Device Preparation
Factory Settings: Mini Storage Tower with 4 eSATA ports
Step 1 Using 3.5” IDE or 3.5” SATA Hard Disk Drives or using Jupiter Mobile Rack with 2.5” IDE Hard Disk Drives. Slide the storage device into the embedded mounting bracket. hard disk drive
Cable connections: • 4 internal SATA data cable • 4-pin floppy power connector for port multiplier power • Power LED
Jupiter mobile rack
Step 2 For model MST4IDEU2:
o Note: Hard drive LED activity lights does not function for this model
Using 3.5” IDE Hard Disk Drives Connect the IDE ribbon cable to the data port of the hard drive and connect the 4-pin Molex power connector to the power port on the hard drive.
o
Using 3.5” SATA Hard Disk Drives with SATA to IDE converter (ADSAIDE)
Plug-in the SATA to IDE converter to the SATA interface of the hard drive. Connect the Y-power cable’s 4-pin floppy power connector to the 4-pin power port on the converter and then connect the IDE ribbon cable to the 40-pin IDE connector of the converter.
For models MST5X1PM, MST5XHPM, MST4ML & MST4ESA:
o
Using 3.5” SATA Hard Disk Drives Connect the internal SATA data cable to the data port of the hard drive then connect the 15-pin SATA power connector to the power port on the hard drive.
o
Using 3.5” IDE Hard Disk Drives with IDE to SATA converter (ADIDESA) Plug-in the IDE to SATA converter to the IDE interface of the hard drive. Connect the Y-power cable’s 4-pin Molex power connector to the power port on the hard drive. Using the middle connector on the Ypower cable plug it to one of the 4-pin Molex connector connected to the power supply. To power the converter, connect the Y-power cable 4-pin floppy power connector to the 4-pin power port on the converter then attach the internal SATA data cable to the data port of the converter.
o
Using Jupiter Mobile Rack with 2.5” IDE Hard Disk Drives and a IDE to SATA converter (ADIDESA) Plug-in the IDE to SATA converter to the IDE interface of the mobile rack. Connect the Y-power cable’s 4-pin Molex power connector to the power port of the mobile rack. Using the middle connector on the Y-power cable
Plug it to one of the 4-pin Molex connector connected to the power supply. Connect the Y-power cable 4-pin floppy power connector to the 4-pin power port on the converter. Also connect the internal 900 right angled SATA data cable to the data port of the converter.
Step 3 Secure the hard disk or mobile rack by using screws provided. Be sure to use the pre-punched hole near the edge of the casing to screw the mobile rack to give ample clearance for the SATA cable.
Repeat the above procedure for additional hard drives or mobile rack Step 4 To power on the mini storage tower press the switch in front of the tower. Note: For Jupiter Mobile Rack configuration on the Mini Storage Tower, it is important to use an internal 900 right angle SATA data cable.
Description MST5X1PM: Mini Storage Tower with one 5X1 Port Multiplier installed.
MST4ESA: Mini Storage Tower (black) with 4 eSATA ports
For better cable management, up to 4 hard drives can be place inside the mini storage tower and be connected to your system via one eSATA cable using a port multiplier.
Connects drives to system via 4 individual eSATA ports
Either 3.5” SATA or 3.5” IDE hard drives can be used with the MST5X1PM. If 3.5” IDE hard drives are to be used additional components must be purchased to convert the IDE interface of the hard drive to SATA interface. Both configurations will be illustrated in the next pages. Note: Hot swap feature depends on the SATA controller the port multiplier is connected to, not on the storage tower. All Addonics SATA controllers support the hot swap feature. Port Multiplier does not work with SATA controller that has no port multiplier (PM) support. Check with your system supplier to confirm the PM support on your existing SATA port. MST5XHPM: Mini Storage Tower with one 5X1 Hardware Port Multiplier installed. For better cable management, up to 4 hard drives can be place inside the mini storage tower and be connected to your system via one eSATA cable using a hardware port multiplier. Either 3.5” SATA or 3.5” IDE hard drives can be used with the MST5XHPM. If 3.5” IDE hard drives are to be used additional components must be purchased to convert the IDE interface of the hard drive to SATA interface. Both configurations will be illustrated in the next pages. MST4IDEU2: Mini Storage Tower with JBOD USB 2.0 adapter installed. You can connect up to 4 IDE hard drives (or SATA hard drives using the Addonics SATA-IDE converter) inside the mini storage tower to your system with 1 single USB cable. The 4 drives can be set up to appear to your system as 1 large drive, 2 drives or as 4 individual drives. MST4SAML: Mini Storage Tower with 4SATA Multilane connector installed. For better cable management, up to 4 hard drives can be place inside the mini storage tower and be connected to your system via 1 Infiniband Multilane 4X cable. Either 3.5” SATA or 3.5” IDE hard drives can be used with the MST4SAML. If 3.5” IDE hard drives are to be used additional components must be purchased to convert the IDE interface of the hard drive to SATA interface. Both configurations will be illustrated in the next pages.
Either 3.5” SATA or 3.5” IDE hard drives can be used with the MST4ESA. If 3.5” IDE hard drives are to be used additional components must be purchased to convert the IDE interface of the hard drive to SATA interface. Both configurations will be illustrated in the next pages.
Technical Support If you need assistance to get your unit functioning properly, please call Addonics Technical Support. Our technical staff will be happy to assist you, but they will need your help to do so. Calling the technical support staff without all the proper information can be both time consuming and frustrating. Here are some tips to help you out: MODEL NUMBER – Please have this number on hand. SYSTEM INFORMATION – Type of computer, peripherals, etc. OPERATING SYSTEM – What version of Windows WHAT’S THE TROUBLE? – Give enough information about your problem so that we can recreate and diagnose it. FREE Software Drivers for all Addonics Technologies Products are available 24 hours per day at the World Wide Web Site: www.addonics.com. Contact Information Phone: 408-433-3899 Fax: 408-433-3898 Email: http://www.addonics.com/sales/query/ Internet: http://www.addonics.com TECHNICAL SUPPORT Phone: 408-433-3855 Hours: 8:30 am - 6:00 pm PST Email: http://www.addonics.com/support/query/
