Ademco - 665 Power Transfer Unit With No.661 Printer

Transcript

POWER TRANSFER,UNCT WITH NO. 661 PRINTER No..665 GENERAL INFORMATION The No. 665 Power Transfer Unit supervises the AC power being supp.lied to Ademco’s No. In the event of an AC power failure, 660 Digital Dialer Receiver and the No. 661 Printer. the No. 665 automatically switches both the receiver and printer to a standby wet cell battery. When power is restored, the No. 665 automatical.ly switches them back to AC operation and begins recharging the wet cell battery. The No. 1. 2. 3. 4. 665 consists A A A A of: steel cabinet housing supervisory circuitry. No. 1321 plug-in low voltage transformer. two-wire single-plug connector. three-wire double-plug connector. Ademco recommends that the battery a 12 volt wet cell battery is required. In addition, (A STANDARD 12 VOLT AUTOMOBILE BATTERY WITH A have a minimum rating of 55 ampere hours. RATING OF 55 AMPERE HOURS OR BETTER IS NORMALLY USED.) If’s also telephone company be required. coupler (SUGAV) is used, an Ademco NO. 96 Recharge-A-Pack will Installation Procedure: WARNI NG: IT I S IMPORTArJl’ THAT THIS POWER TRANSFER UNIT BE CONNECTED IN A SPECIFIC SEQUENCE. IF THESE INSTRUCTIONS ARE NOT FOLLOWED IN EXACT ORDER- DAMAGE TO THE NO. 660 AND/OR IJO. 661 MA.‘! KESULT. LOCATION : to the No. 663 Receiver and No. 661 The No. 665 should be located as close as possible e between the No. 665 and the Nos.660-.- 8 Printer. Under ---no circumstances the -------.~--______CI distant -....-.----. - should --.-661 exceed 24 f cJ2-t _ -_- ---...- _ _ - _ . __.. - MOUNTING THE CABINET: 1.’ Open the cover of the No. 665 cabinet and remove the two spade lugs from terminals 3 and 4. (See Diagram 1 I. These wires connect the relay sub-assembly to the printed circuit board and must be removed before attempting to take the wired panel out of the cabinet. Remove the six screws that attach the printed circuit board and relay sub-assembly to the cabinet. Carefully take the printed circuit board and relay sub-assembly out of the cabinet. 2. Mount the No. as possible. 3. Re-instal I both mounted cabinet. ‘Iuq to terminal 665 cabinet as close the No. 660 Receiver and No. the printed circuit board and the relay subrassembly Make certain to reconnect the two spade I uqs, the. 3 and the red wire luq to terminal 4. .89 www.PDF-Zoo.com to 661 Printer into the b I ack wi re NOTE : If a No. 661 Printer with the instructions fer Unit. is not being used, skip the following for wiring the No. 660 Receiver to NO.665 Power I Transfer Unit DIAGRAM 1 --w---e--e--- I i/z 1 Battery J 5514.~ 1 the section and proceed No. 665 Power Trans- “AL~.C&N” I , No.96 Recharge -A- Pack 1: III IL$ I iLACK SUGAQ Coupler No. 660 Receiver No. 661 Printer $1 i \\ ,\2p>H c “’ 0 ‘0 . a-4 Provided with No. 660 PRINTER CONNECTIONS: 1. Unplug the No. 661 Printer rear of the unit is facing tor supplied with the No. ing of the No. 661 Printer from its AC outlet and turn it around so that the you. Attach the two-wire single-plug female connec665 to the male connector extending through the housat the I.ine cord retainer. 2. Extend the leads of the female connector attached to the No. 661 to reach lower terminal strip of the No. 665. Use Chart 1 to determine the number gauge wires which must be run in parallel to make a proper connection. CHART I LENGTH OF WIRE RUN I t 3. I NUMBER OF 16 GA.WIRES REQ’D FOR EACH CONN. 1 1 6 12 18 ft. ft. ft. ft. Connect the extension wire attached to the to to to to wire black 6 12 18 24 ft. ft. ft. ft. attached lead to I to the terminal 90 www.PDF-Zoo.com 1 I 1 1 2 3 4 Per Per Per Per Connect ion Connection Connection Connection red lead 15. to terminal 14 and the the of 16 Although this completes the connection of the No. 661 Printer to the No. 665 Power Transfer Unit, DO NOT PLUG THE NO. 661 BACK INTO ITS AC OUTLET UNTIL THE REST OF THE INSTALLATION INSTRUCTIONS-HAVE BEEN FOLLOWED. NOTE : @ RECEIVER CONNECTIONS: 1. Dialer Receiver from its Unplug the No. 660 Digital Unplug the so that the rear of the unit faces you. ‘I+ 12 V.OUT” from the receptacle marked ‘I+ 12 V.“. AC outlet and turn it around molex connector marked 2. Attach the three-wire double-plug connector included with the No.. 665 to the The male molex plug of the three-wire connector should be attached receiver. The female molex plug to the female ‘I+ 12 V. OUT” molex plug of the No. 660. of the three-wire connector should be attached to the I’+ 12 V.” receptacle. 3. Extend the three leads now attached to the No. 660 to reach the lower terminal Use Chart 1 to determine the number of 16 gauge wires strip of the No. 665. which must be run to make proper connections. 4. Connect the extension wire attached to the red connector wire to terminal 11 of Connect the extension wire attached to the black wire to terminal the No. 665. Connect the extension wire attached to the white wire to terminal 13. 12. Dialer Receiver Although this completes the connection of the No. 660 Digital to the No. 665 Power Transfer Unit, DO NOT PLUG THE NO. 660 BACK INTO ITS AC OUTLET UNTIL COMPLETING THE REST OF THESE INSTALLATION INSTRUCTIONS. NOTE : TELEPHONE COUPLER CONNECTIONS: 1. Place a No. 96 Recharge-A-Pack terminal No. 4 (-1 of the No. inside the No. 665 Power Transfer Unit. 96 to terminal No. 4 (+I of the No. 665. Connect 2. Solder and tape a pair of wires to the red and b \ack flying leads provided in the coupler ccrd which connects the No. 660 Rece iver to the SU6AQ telephone company coupler. OBSERVE POLARITY. The black f lying lead (-1 must be connected to terminal No. 3 (-1 of the No. 665. The red f lying lead (+I must be connected to terminal No. 3 (+I of the No. 96. 3. Connect terminals 1 and 2 of the, No. 96 to the No. 1320 transformer supplied with the unit and plug it into a nearby 24 hour outlet. The 6 volt rechargeable standby batteries built into the No. 96 power supply plus the 12 volt wet cell battery connected to the No. 665 power transfer unit will provide full standby power for the telephone company coupler during an AC power failure. POWER CONNECTIONS: THE NO. 660 RECEIVER, THE NO. 661 PRINTER, AND THE TRANSFORMER FOR THE NO. 665 POWER TRANSFER UNIT MUST BE PLUGGED INTO THEIR RESPECTIVE AC OUTLETS FOLLOWING A DEFINITE PLtiGIN SEQUENCE. DO NOT ATTEMPT TO ATTACH ANY OF THESE UN ITS TO AC UNT I L READ I NG THE FOLLOWING INSTRUCTIONS. 1. Wet Cel I Battery: Locate the 12 volt wet cell battery as close as possible to Under no circumstances, should the battery be located.more than the No,. 665. 24 feet f.rom tE No. 665. Using Chart 1 to determine the number of 16 gauge wires which must be run in parallel to make proper connections, connect leads to 91 www.PDF-Zoo.com terminals 5 and 6 of the No. 665 and bring them to the wet cell battery. Attach the wire connected to terminal 5 to the negative side of the battery. BE SURE TO OBSERVE POLARITY. DO NOT ATTACH THE REMAINING WIRE TO THE POSITIVE SIDE OF THE BATTERY AT THIS TIME. 2. Locate the 24 hour AC outlet nearest to the No. 665. Be sure the current to this outlet is not interrupted by a switch or by a circuit breaker when the office is closed for the day. Make preparations for the AC connection. Attach the No. 1321 Plug-in Transformer to the No. 665 Power Transfer Unit using terminals 1 and 2. At least 18 gauge wire should be used for this connection. -DO NOT PLUG THE NO. 1321 TRANSFORMER INTO THE AC OUTLET AT THIS TIME. 3. Plug the No. 660 Digital Dialer Receiver into its AC outlet. turn on and the two relays in the No. 665 Power Transfer Unit If the horn sounds in the No. 660 Receiver, push the “silence to reset it. E-. Plug the No. 661 Printer into the AC out let. The Printer will but the time will have to be adjusted fo I lowing the instructions the Printer. f .” Connect the.unattached minal of the wet cell 6. Plug in the No. The No. 660 should should pull in. alert” button now be operable supp lied with lead from termina I 6 of the No. 665 to battery. POLAR I TY MUST BE OBSERVED. the pos itive ter- 1321 Transformer. THIS COMPLETES THE INSTALLATION TEST PROCEDURE: 1. in the followinq order, the No. 665 Power Transfer Unit, the IJo. 660 Unplug, and the No. 661 Printer from their respective AC outlets. Ttle No. Receiver, 660 and the No. 661 should turn off and then come back on an instant later, operating from battery power. The horn in the No. 660 Diqital Receiver may come on reset it by pushing the -“si lence a I ert” button on the at this time. If it does, front of the No. 660. 2. Check the operation at the rear of the 3. Check the operation of the No. 661 Printer bottom of the rear panel of the Printer. -.the-.- _-pr i nt.c+i: out by the unit at this time. 4. Plug in, ---.in the -.-_--.._a foIIowin:Lorderand the No. 665 Power Transfer www.PDF-Zoo.com by using the lamp test button of the No. 660 Receiver unit. By pushinq this button, 8888 will be displayed. only, Unit. the 92 by using the Disregard No. located, print button ---;---located any code information 660 Receiver, the; No. 661 Printer, at *pi No.665 IMPORTANT NOTE : The information Receiver/Printer POWER TRANSFER UNIT WITH NO. 661T PRINTER These instructions describe the use of the No. 665 with a No. 661T To connect to the earlier No. 661 Ink Printer, Thermal Type Printer. see the particular Installation Instructions elsewhere in this section. contained (thermal herein type) is applicable as well for Rack Mounting. to the No. 673T Digital GENERAL INFORMATK)N: The No. 665 Power Transfer Unit supervises the AC power being supplie( to Ademco’s No. 660 Digital Receiver. It also provides continuous DC power for the No. 661T (Thermal) Printer to maintain the electronic clock circuitry. In the event of an AC power failure, the No. 665 automatically switches the receiver to a standby wet cell battery. When power is restored, the No. 665 automatically switches it back to AC operation and begins recharging the wet cell battery. The No. 1. 2. 3. 4. A A A A 665 consists of: steel cabinet housing supervisory circuitry. No. 1321 plug-in low voltage transformer. two-wire single-plug connector. three-wire double-plug connector. In addition, a 12 volt wet cell battery is required. Ademco recommends that the battery have a minimum rating of 55 ampere hours (a standard 12 V. automobile battery is normally used. We recommend the use of a maintenance free, sealed lead acid battery - the type which docsn’ t vent c;ases into the atnosphcrc nor which requires the addition of water). INSTALLATION PROCEDURES: Locat ion: The No. 665 should be located as close as possible to the No. 660 Receiver and No. 661T Printer. I!r,Jer no circumstances should the distance between the No. 665 and the Nos. 660 -.----_- .,_.-- -_-----and 661T exceed 24 feet. _-..-----we.-.-- Before Proceeding: yake sure that Nos. 660, sources and that the No. Caution: -_.--- 661T and 665 are unplugged from their 665’s standby battery is not connected. respective AC power IT IS IMPORTANT THAT THE CONNECTlO!: PROCEDURES DESCRIBED HEREIN BE FOLLOWED IN EXACT SEQUENCE. OTHERWISE, DAMAGE TO THE EQlJIPMEIJT MAY RESULT. 93 www.PDF-Zoo.com No.665 Power ‘A.C. ON” Light Transfer Unit \ I II II 1 j . “BLACK” “WHITE” _I.. L-..Y IV I.“. 665 AS REQUIRED I srB I No. 660 I, 1 I I 1 DC OUT” (DISCONNECTED) I 7 I INog7 *n Lamp) 1 I I I I1 b. f ; I 2 WIRECORD WITH CONNECTOR (SUPPLIED WITH No. 665) No. 665) CONNECTOR ‘MALE RECEIVER (lop) J FRONT- 4 uuuuu / < e FRONT-/ -AC LINYCORDS Unplug before conriecting units to No. 665. Follow connection sequence in No. 665’s instructions when plugging in. Diagram: Printer CONNECTION Connect Note : OF RECEIVER AND (THERMAL) PRINTER TO NO. 665 ions: If a Printer is tions for wiring not being used, skip the No. 660 Receiver this section to the No. and proceed with 665 Power Transfer the instrucUnit. 1. At the rear of the No. 6617, unpluq the connector marked “12V. DC OUT” from the “12V. DC IN” connector. Connect the 2 wire cord with connector supplied with the The 32V DC @lIT” connector wi I I No. 665 to the No. 66lT’s “12V. DC INPUT” connector. remain disconnected. 2. Extend the leads of the 2 wire cord strip of the No. 665. Use the chart wires which must be run in parallel www.PDF-Zoo.com with connector to reach the lower below to determine the number of to make a proper connection. terminal the 16 gauge I Chart 1 3. Connect lead to Note : LENGTH OF WIRE RUN I 6 12 I8 the extended terminal 15. ft. ft. ft. ft. to to to to 6 12 18 24 RED lead NUMBER OF 16 GA.WIRES REQ’D FOR EACH CONN. I ft. ft.. ft. ft. to I I 2 3 4 terminal 6 of Per Per Per Per the Connect ion Connection Connection Connect-Ion No. _,. 665 and the extended Although this completes the connection of the No. 661T Printer to the Power Transfer Unit, do not plug the No. 661T into its AC outlet until of the installation instructions have been followed. ----..-- BLACK No. 665 the rest Receiver Connect ions: 1. With the No. 660 Digital Receiver still unpluqqed from its around so that the t-ear of the unit faces you. Unp luq the ‘I+ 12V.” from each other. 2. Attach the three-wire double-pluq connector included with the No. 665 to the receive?. The male molex plug of the three-wire connector should be attached to the female ‘I+ 12V.” plug of the No. 660. The female plug of the three-wire connector should be attached to the No. 660’s ma I e “+ 12V .” connector. 3. Extend the three leads now attached to the No. strip of the No. 665. Use Chart 1 to determine must be run to make proper connections. 4. Connect the extension the No. 665. Connect Connect the extension --Note : wire attached the extension wire attached AC outlet, connectors turn it marked 660 to reach the lower terminal the number of 16 gauge wires to the RED connector wire attached to the to the WHITE wire to which wire to terminal 11 of BLACK wire to terminal terminal 13. 12. Although this completes the connection of the No. 660 Digital Receiver to the No. 665 Power Transfer Unit, DO NOT PLUG THE NO. 660 BACK INTO ITS AC outlet UNTIL COMPLETING THE REST OF THESE -INSTALLATION INSTRUCTIONS. Power Connect ions: THE NO.660 RECEIVER AND THE TRANSFORMER FOR THE NO. 665 POWER TRANSFER UNIT MUST BE PLUGGED INTO THEIR RESPECTIVE AC OUTLETS FOLLOWING A DEFINITE PLUG-IN SEQUENCE. DO NOT ATTEMPT TO ATTACH ANY OF THESE UNITS TO AC UNTIL READING THE FOLLOWING INSTRUCTIONS. 1. * Wet Cell Battery: Locate the 12 volt wet cell battery as close as possible to the No. 665. Under no circumstances, should the battery be located more than 24 feet from the No. 665. Using Chart 1 to determine the number of 16 gauge wires which must be run in parallel to make proper connections, connect leads to terminals 5 and 6 of the No. 665 and bring them to the wet cell battery. Attach the wire connetted to terminal 5 to the negative side of the battery. BE SURE TO OBSERVE POLARITY. DO NOT ATTACH THE REMAINING WIRE TO THE POSITIVE SIDE OF THE --.--_-. ----, BATTER? AT THIS TIME. i . 95 www.PDF-Zoo.com 1 2. Locate the 24 hour outlet nearest to the No. 665. Be sure the current to this outlet is not interrupted by a switch or by a circuit breaker when the Make preparations for the AC connection. premises are closed for the day. Attach the No. 1321 Plug-in Transformer to the No. 665 Power Transfer Unit 18 gauge wire should be used for this using terminals 1 and 21 At least connection. DO NOT PLUG THE NO. 1321 TRANSFORMER INTO THE AC OUTLET AT THIS TIME. 3. Pluq the No. 660 Digital Receiver into its AC outlet. The No. 660 should the two relays in the No. 665 Power Transfer Unit should pull in. If the in the No. 660 Receiver, push the SILENCE ALERT button to reset it. 4. Connect the unattached of the wet cell battery. 5. Pluq 6. Pluq the No. 661T Printer into the AC outlet. This synchronizes the clock circuitry in the No. 661T to the AC power line. The printer will now be operable but the time will have to be adjusted following the instructions supplied with the printer. Note : If l-his AC subsequently fails, internal clock circuitry in the No. 661T takes over automatically during the outage. I in the No. lead from terminal 6 of the No. POLARITY MUST BE OBSERVED. 665 to the positive turn horn on and sounds terminal 1321 Transformer. THIS COMPLETES THE INSTALLATION TEST PROCEDURE: 1. Unplug the No.665 Power Transfer Unit and the No. 660 Receiver from their respective AC outlets. The No. 660 should turn off and then come back on an instant later, 0pe-r.. ating from battery power. The horn in the No. 660 Digital Receiver may come on at this time. If it does, reset it by pushing the SILENCE ALERT button on the front of the No. 660. 2. Check the operation of the rear of the unit. the No. 660 Receiver by using the LAMP TEST button located By pushing this button, the number 8888 will be displayed. 3. Check front time. the No. 661T Printer Disregard any code ‘4 . Pluq .-.-in the ^-No.. - -660 .--.- -_Receiver the operation of the printer. of and the by using information No. 665 Power the PRINT switch located printed out by the unit Transfer Unit. SPECIFICATIONS: Physical: Width: Height: Depth : -Electrical: Input: o&put: Stand by : Fuse: www.PDF-Zoo.com 7 l/2” 12” 3 l/4” (19.0 (30.5 ( 8.2 cm) cm) cm) 18V. AC from No. 1321 Plug-in Transformer 12V. DC, 500 ma (max.) up to 168 hours, using 12V., 55 AH Wet Cel I Battery (with No. 660 Receiver and No. 661T Printer connected and depending upon the report i ng rate 1 7.5A Slo-Blo (No. 90-4) 96 at on the at this f-1 TROUBLESHOQTIMG No.665 TROUBLE : 1. THE DIGITAL CLOCKINTHE 5 MINUTES PER DAY). ATTACHED PRINTER APPEARS TO LOSE TIME &‘PROXIMATELY PROBABLE CAUSE Extended use of operatinq from printout of all FEED switch is position (Nos. cates that the interrupted or that the clock TROUBLE: 2. THE UNIT’S REMEDY the equipment when standby battery (a 9s when the PRINT/ raised to the PRINT 661T or 673T) indipower supply was just turned on, and must be reset). FUSE (7.5 Reset the time-of-day to the correct indication as described in the instrucBe sure that the unit is plugged t ions. into AC power at all times. AMPERE) HAS BLOWN, LEAVING UNIT PROBABLE CAUSE A. A momentary short unit’s output(s) to blow. B. : The sequence not fol lowed TROUBLE : -- REMEDY circuit of the has caused the fuse of connections EXACTLY. INOPERATIVE. A. Replace (Ademco were with a 7.5 No. 90-4). amp (Slo-Blo) Review printer, receiver and power connection sequence found in the Installation Instructions. 3. THE PRINTER AND RECEIVER WILL NOT OPERATE ON STANDBY POWER WHEN A.C. REMOVED. between 12 volt and No. 665 are POWER IS REMEDY PROBABLE CAUSE A. Connections aqe battery camp I ete. \ fus_e_ stornot A. Check connections nals and terminals No. 665. at battery termi5(-I and 6(+) of The battery (non-sealed, venting type) is in need of water or is d i scharqed. 8. Check water level and add distilled Measure specific water as required. qravity of each cell usi’nq a hydroReplace battery ii it cannot meter.. be recharged. charqing circuitry in C. Defective unit is failinq to charqe battery (measure DC output voltage at terminals 5 (-1 and 6 (+I of the No. 665 with any one of the attached leads to these terminals disconnected). C. Look for a minimum of 12 volts 0-C. at these terminals with,printer and receiver plugged into A.C. outlets, and connections to the print.er and Return unit to receiver left intact. Ademco for servicinq if th.is voltaqe is not obtained. 8. 97 www.PDF-Zoo.com