Transcript
INSTALLATION INSTRUCTIONS
Accessory
Application
XM RADIO SYSTEM
2004 ACCORD 2-DOOR (LX/EX L4, LX V6)
Publications No.
AII 25749
PARTS LIST
Issue Date
FEB 2004
Double-sided adhesive tape
XM Radio Attachment Kit (sold separately): P/N 08B15-SDN-100
DIN cable
Display unit pocket
Clip nut XM radio harness 3 Self-tapping screws
Fastener Upper bracket
Ground bolt (gold)
Lower bracket
6 Washer-screws, 4 x 8 mm
2 Washer-bolts, 6 x 12 mm Modulator bracket
4 Flange nuts, 4 mm 2 Washer-screws, 5 x 10 mm 30 Wire ties 2 Flange nuts, 5 mm Connector clip 3 Off-set wire ties with clip 8 Wire tie with clips (two not used)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
AII 25749 (0402)
08B15-SDA-1001-91
1 of 22
5 Cushion tapes
Audio Attachment Kit (sold separately): P/N 08B06-SDA-100 (Not required if already equipped with a player.)
5 EPT sealers Left player bracket
Fuse label
Mini fuse, 5A
Right player bracket
Antenna Kit (sold separately): P/N 08A15-1E1-100 Left player subbracket Antenna cable
Right player subbracket Base Kit (sold separately): P/N 08A15-1E1- 000 Player base-bracket Display unit
FM modulator unit
Player panel
Receiver unit Pocket
Owner's Manual
2 of 22
BUS cable (Used on vehicles without Navigation)
AII 25749 (0402)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
2 Latches
Illustration of the XM Radio System Installed in the Vehicle
8 Flange nuts, 6 mm
DISPLAY MODULE
RECEIVER UNIT
ANTENNA
DIN CABLE
2 Grommet screws
2 Wire ties 2N28160M
FM MODULATOR UNIT
3 EPT sealers
XM RADIO HARNESS
VEHICLE ANTENNA CABLE DISPLAY MODULE
2 Self-tapping screws, 4 x 12 mm
TOOL AND SUPPLIES REQUIRED Phillips screwdriver Stubby Phillips screwdriver Flat-tip screwdriver Isopropyl alcohol Shop towel Tape measure Utility knife Hook tool Ratchet wrench 8 mm and 10 mm Sockets Felt-tip pen Scissors Push pin Vinyl tape Drill 3 mm and 10 mm Drill bits Touch-up paint Eye protection (face shield, safety goggles, etc.) Masking tape
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
FM MODULATOR UNIT
DIN CABLE RECEIVER UNIT FUSE BOX 6-PIN CONNECTOR XM RADIO HARNESS
ANTENNA 2N28010M
AII 25749 (0402)
3 of 22
INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 1.
Make sure you have the anti-theft code for the radio, then write down the radio station presets.
2.
Disconnect the negative cable from the battery.
3.
Remove the trim ring.
•
Gently pry up on the trim ring to release the six clips.
•
Unplug the two seat heater connectors (if equipped), and remove the trim ring.
RETAINING CLIPS (4)
RETAINING CLIPS (2)
M/T Vehicle: •
Squeeze the plastic clip, and pull down on the shift boot. Remove the shift knob by turning it counterclockwise. TRIM RING
SHIFT KNOB (Turn counterclockwise.)
SEAT HEATER CONNECTOR (if equipped) 2206041K
A/T Vehicle:
PLASTIC CLIP
SHIFT BOOT
•
Gently pry on the trim ring to release the six clips.
•
Unplug the two seat heater connectors (if equipped), and remove the trim ring.
2206032K
RETAINING CLIPS (4)
RETAINING CLIPS (2)
TRIM RING
SEAT HEATER CONNECTOR (if equipped)
2206112K
4 of 22
AII 25749 (0402)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
4.
If the vehicle is equipped with a cassette/MP3/CD player, go to step 13; otherwise, go to step 5.
Remove the center holder. •
Open the lid, and remove the coin pocket.
•
Remove the two self-tapping screws.
•
Gently pull out the dashboard center holder to release the two retaining clips, unplug the vehicle connector, and remove the center holder.
5.
Remove the pocket: •
Apply masking tape to the edge of the center panel.
•
Remove the two self-tapping screws.
•
Push in on the bottom of the lid, then pull out on the top by inserting the end of a hook tool between the pocket and center panel. Pull the pocket toward you to release the two retaining clips.
•
Set the pocket aside; it will not be reused.
With Coin Pocket: COIN POCKET
LID
CENTER HOLDER SELF-TAPPING SCREW
MASKING TAPE
HOOK TOOL RETAINING CLIPS (2) RETAINING CLIPS (2)
POCKET LID
VEHICLE CONNECTOR POCKET
With Optional Ashtray:
2206061K
•
Open the lid, and remove the ashtray.
•
Remove the two self-tapping screws.
•
Gently pull out on the two retaining clips, unplug the cigarette lighter harness connector, vehicle connector, illumination bulb, and remove the center holder. CENTER HOLDER
SELF-TAPPING SCREW
6.
ASHTRAY SELF-TAPPING SCREW
ILLUMINATION BULB
2206073K
Remove the right and left inner covers (one hook and one clip for each cover). Set the inner covers aside; they will not be reused. CLIP LEFT INNER COVER
RETAINING CLIPS (2)
RIGHT INNER COVER 2730010K
VEHICLE CONNECTOR
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
CIGARETTE LIGHTER HARNESS CONNECTOR
AII 25749 (0402)
POCKET OPENING HOOK 2226010K
5 of 22
7.
Remove the vehicle harness clip from the vehicle frame, and move the clip out of the way. PLAYER BASEBRACKET
VEHICLE FRAME
10. Get the pocket from the audio attachment kit. Using a utility knife, cut the two lugs off of the pocket. LUG (Cut off.)
VEHICLE HARNESS CLIP (Remove.)
6 mm FLANGE NUT POCKET LUG
VEHICLE FRAME 6 mm FLANGE NUT
11. Install one latch onto the left and right player brackets. Slide the clip nut onto the display module pocket flange.
2306011T
VEHICLE HARNESS CLIP (Insert into the hole of the player base-bracket.)
LATCH
Insert the studs from the player base-bracket into the holes in the vehicle frame from the back. Install the two 6 mm flange nuts while holding the bracket firmly against the vehicle frame. Insert the vehicle harness clip (removed in step 7) into the hole in the player base-bracket.
9.
Insert the studs of the left and right player subbrackets into the holes in the vehicle frame, and install one 6 mm flange nut on the end of each stud while pushing each subbracket upward.
DISPLAY MODULE POCKET
SELFTAPPING SCREW (2) (supplied with audio attachment kit)
VEHICLE FRAME
LEFT PLAYER BRACKET
SCREW POSITION
RIGHT PLAYER SUBBRACKET
6 of 22
2306021T
LATCH
CLIP NUT
6 mm FLANGE NUT
LEFT PLAYER SUBBRACKET
DISPLAY MODULE POCKET FLANGE
1 mm
8.
VEHICLE FRAME
2529041T
POCKET RIGHT PLAYER BRACKET
SELF-TAPPING SCREWS (3) (supplied with XM radio attachment kit) 2N28071M
BRACKET HOLE
12 Set the display module pocket on the pocket with the cut out facing up. Position the left and right player brackets on the display module pocket and pocket, and install five self-tapping screws.
AII 25749 (0402)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
If the vehicle is not equipped with a cassette/MP3/ CD player, go to step 18; otherwise, go to step 13.
15. Remove the left and right audio brackets (two washer-screws and one self-tapping screw for each bracket). Separate the player and pocket. Set the pocket aside; it will not be reused.
13. Remove the player panel by removing the two self-tapping screws and two clips. CLIP PLAYER PANEL
WASHERSCREW
SELF-TAPPING SCREW
SELFTAPPING SCREW
2306141T
14. Remove the player/pocket assembly. Unscrew the four flange nuts, and pull the assembly out toward you. Unplug the audio subharness cable connector. VEHICLE CONNECTOR (without navigation system) VEHICLE CONNECTOR (with navigation system)
PLAYER (Cassette/MP3/CD)
POCKET (Do not reuse.)
SELF-TAPPING 2N28080M SCREW
DISPLAY MODULE POCKET
AUDIO SUBHARNESS CONNECTOR (without navigation system)
WASHERSCREW (supplied with Audio Attachment kit)
LEFT PLAYER SUBBRACKET
CLIP NUT
PLAYER (Cassette/MP3/CD) WASHERSCREW (supplied with Audio Attachment kit)
SELFTAPPING SCREW LEFT PLAYER BRACKET
RIGHT PLAYER BRACKET
BRACKET HOLE 6 mm FLANGE NUT
RIGHT PLAYER BRACKET PLAYER BASEBRACKET
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
SCREW POSITION RIGHT PLAYER SUBBRACKET
WASHERSCREW
16. Slide the clip nut (supplied) onto the display module flange.
AUDIO SUBHARNESS CONNECTOR (with navigation system) LEFT PLAYER BRACKET
RIGHT AUDIO BRACKET
LEFT AUDIO BRACKET
DISPLAY MODULE
SELF-TAPPING SCREWS (2) (supplied with XM radio attachment kit)
17. Set the player on the display module pocket. Position the left and right player brackets on the display module pocket and player, and reinstall the four washer-screws. Install the three self-tapping screws to secure the display module pocket.
AII 25749 (0402)
7 of 22
Installing the Display Unit
If the vehicle is not equipped with a cassette/MP3/ CD player, go to step 20; otherwise, go to step 19.
18. Attach the display unit to the display unit pocket: •
Using isopropyl alcohol on a shop towel, clean the center on the back of the display unit where the adhesive backing will attach.
•
Remove the backing from one side of the double-sided adhesive tape, and attach it to the display unit.
•
Remove the remaining backing from the double-sided adhesive tape. Route the display unit cable through the hole of the display unit pocket, and attach the display unit to the display module pocket.
19. Plug the audio subharness cable into the player. Cassette Player Make loops in the audio subharness cable, and secure it with one wire tie, so that the distance between the ends of the cable connector is 200 mm. Plug the audio subharness cable connector into the cassette player connector. CASSETTE PLAYER WIRE TIE (supplied with audio attachment kit)
DISPLAY UNIT AUDIO SUBHARNESS CABLE
DOUBLE-SIDED ADHESIVE TAPE
AUDIO SUBHARNESS CABLE CONNECTOR
Clean with isopropyl alcohol.
BACKING
Without Player:
DISPLAY UNIT CABLE
With Player:
AUDIO SUBHARNESS CABLE CONNECTOR 200 mm 2306051T
DISPLAY UNIT POCKET
Multimedia Player Make loops in the audio subharness cable, and secure it with one wire tie so that the distance between the ends of the cable connectors is 200 mm. Plug the audio subharness cable connector into the multimedia player connector.
POCKET PLAYER
MULTIMEDIA PLAYER
BUS CABLE
DISPLAY UNIT CABLE
DISPLAY UNIT POCKET
WIRE TIE (supplied with audio attachment kit) 2N28110M
AUDIO SUBHARNESS CABLE CONNECTOR
AUDIO SUBHARNESS CABLE CONNECTOR 200 mm 2306061T
8 of 22
AII 25749 (0402)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
In-Dash CD Player •
•
21. Remove the rear console.
Make loops in the audio subharness cable, and secure it with one wire tie so that the distance between the ends of the cable connectors is 180 mm. Plug the audio subharness cable connector into the connector from the in-dash CD player. After connecting, secure the connectors to the rear of the in-dash player with one wire tie from the in-dash CD player kit.
IN-DASH CD PLAYER
AUDIO SUBHARNESS CABLE CONNECTOR
WIRE TIE (supplied with audio attachment kit)
•
Open the lid, and remove the rear console mat from inside the rear console.
•
Remove the two screws and the four selftapping screws, and unplug the connector and harness clip (if equipped).
•
If equipped with a console-mounted CD changer, remove the changer from the rear console.
REAR CONSOLE MAT
SELF-TAPPING SCREWS (4)
SCREWS (2)
WIRE TIE (supplied with audio attachment kit) AUDIO SUBHARNESS CABLE 180 mm AUDIO SUBHARNESS CABLE CONNECTOR 2306070T
HARNESS CLIP (if equipped) CONNECTOR (if equipped)
2206090K
Routing the XM Radio Harness 20. Remove the beverage holder (pull up to release the six retaining clips).
RETAINING CLIPS (2)
RETAINING CLIPS (4)
BEVERAGE HOLDER
2206050K
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
AII 25749 (0402)
9 of 22
22. Remove the driver’s dashboard lower cover:
24. Remove the self-tapping screw and the clip that secure the left front console cover. Take care not to damage the clip, and remove the console cover.
•
Remove the self-tapping screw.
•
Release the four clips on the left side first by pulling out on the driver's dashboard lower cover.
•
After releasing the four clips, insert a flat-tip screwdriver behind the clip at the dashboard frame. Gently twist the screwdriver to release the clip.
•
SELF-TAPPING SCREW
Release the two clips on the right side. Unplug the vehicle connector, then remove the lower cover.
CONNECTOR
CLIP
DASHBOARD LOWER COVER
LEFT FRONT CONSOLE COVER
PUSH
SELFTAPPING SCREW
REMOVE
2206131K
RETAINING CLIPS (7)
2206120K
23. If equipped, remove the driver’s dashboard under cover (release the three retaining clips, one pin, and one holder).
HOLDER
PIN RETAINING CLIPS (3)
10 of 22
DRIVER’S DASHBOARD UNDER COVER
2205020T
AII 25749 (0402)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
25. On the driver's side of the vehicle, locate the 6-pin connector on the fuse box. Plug the XM radio harness 6-pin connector into the fuse box 6-pin connector.
27. Install the XM radio harness fuse cases and the 6-pin dummy connector to the fuse box case. Fuse case position
NOTE: If the 6-pin connector is already being used by another accessory, locate the 6-pin connector taped to the XM radio harness. Remove the dummy connector from the harness, and plug the other accessory's harness 6-pin connector into the XM radio harness.
FUSE CASES VEHICLE HARNESS (Do not secure to the yellow SRS harness.)
OTHER ACCESSORY 6-PIN HARNESS
XM RADIO HARNESS 6-PIN CONNECTOR
WIRE TIE XM RADIO HARNESS
DUMMY CONNECTOR (Discard.) 2524060M
2N28020M
6-PIN CONNECTOR
FUSE BOX 6-PIN CONNECTOR FUSE CASES
XM RADIO HARNESS 6-PIN CONNECTOR WITH DUMMY CONNECTOR
28. Secure the XM radio harness to the vehicle harness with one wire tie. Do not secure it to the yellow SRS harness. 29. Route the XM radio harness under the steering shaft and toward the center console. VEHICLE HARNESS
FUSE LABEL 2A LABEL
XM RADIO HARNESS CLIP
5A LABEL
2524051M
WIRE TIES (3) FUSE LABEL CENTER CONSOLE
XM RADIO HARNESS 3121030M
Use these labels. 2N28030M
26. Attach the fuse labels to the fuse cases on the XM radio harness.
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
29. Loosely attach the XM radio harness to the vehicle harness with three wire ties. AII 25749 (0402)
11 of 22
30. Inside the center console, locate the welded nut on the vehicle stay. Attach the XM radio harness ground terminal to the welded nut with the ground bolt supplied.
33. Attach the modulator bracket to the player basebracket with two 5 x 10 mm washers and two 5 mm flange nuts.
WIRE TIE
CUSHION TAPE
HALF CUSHION TAPE MODULATOR BRACKET
Cut
GROUND BOLT
5 mm FLANGE NUT
Clean with isopropyl alcohol.
VEHICLE HARNESS
PLAYER BASEBRACKET
3-PIN CONNECTOR
GROUND TERMINAL
XM RADIO HARNESS
HALF CUSHION TAPE
3606010M
31. Secure the XM radio harness to the vehicle harness with one wire tie. Route the 3-pin connector, and the remaining end of the XM radio harness toward the rear of the vehicle; they will be routed later. FM Modulator Unit Installation 32. To protect the center panel, attach masking tape to the center panel in the area shown.
5 x 10 mm WASHERSCREW
3605060M
34. Using scissors, cut one cushion tape in half. Using isopropyl alcohol, clean the bonding surfaces of the brackets, and attach the half cushion tapes to the brackets in the area shown. 35. Install the FM modulator unit to the modulator bracket with two 4 x 8 mm washer-screws. Attach the connector clip from the FM modular unit harness into the hole in the player base-bracket.
CENTER PANEL
FM MODULATOR BRACKET 4 x 8 mm WASHERSCREW
MASKING TAPE
MODULATOR BRACKET 4 x 8 mm WASHERSCREW
HOLE OF THE MODULATOR BRACKET
PLAYER BASE BRACKET
2506010T 3605071M
CONNECTOR CLIP
12 of 22
AII 25749 (0402)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
36. Insert the studs from the player base-bracket into the holes in the vehicle frame from the back, then install the two 6 mm flange nuts while holding the bracket firmly against the vehicle frame.
39. Unplug the vehicle antenna cable, and plug it into the FM modulator unit antenna cable. Plug the other end of the FM module antenna jack into the vehicle antenna cable. WIRE TIE WIRE TIE VEHICLE HARNESS
PLAYER BASE-BRACKET
VEHICLE HARNESS WIRE TIE
EXCESS ANTENNA CABLE
EPT SEALER VEHICLE FRAME 6 mm FLANGE NUTS (2)
3605081M
37. Connect the XM radio harness 3-pin connector to the FM modulator unit harness 3-pin connector. 38. Get a DIN cable from the XM radio attachment. Plug the 90° end of the DIN cable connector into the FM modulator unit, then route the DIN cable rearward along the XM radio harness .
XM RADIO HARNESS 3-PIN CONNECTOR
3606042M
FM MODULATOR ANTENNA CABLE
FM MODULATOR UNIT
DIN CABLE
VEHICLE ANTENNA CABLE
40. Wrap one EPT sealer around the antenna jack, and secure the antenna cable to the vehicle antenna cable with the one wire tie. Secure both antenna cables to the vehicle harness with one wire tie. 41. Loop the excess antenna cable from the FM modulator, and secure the excess cable to the vehicle harness with two wire ties.
FM MODULATOR UNIT HARNESS CONNECTOR 3609041M
XM RADIO HARNESS
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
AII 25749 (0402)
13 of 22
42. Plug the display module cable into the FM modulator unit. Pull the excess length of the cable out from under the display module unit.
45. Loop the excess display module cable along the DIN cable and the vehicle harness, then secure the display module cable, and the DIN cable with one wire tie with clip. Insert the clip from the wire tie into the modulator bracket hole.
MODULATOR BRACKET HOLE
DISPLAY MODULE UNIT
DISPLAY MODULE CABLE
WIRE TIE WITH CLIP
XM RADIO HARNESS
DISPLAY MODULE CABLE (Pull out.)
REAR 3606052M
WIRE TIE
WIRE TIE
43. If equipped with a player, plug the BUS cable connector into the vehicle connector.
3606061M
DIN CABLE
46. Near the subbracket, secure the XM radio harness to the vehicle harness with one wire tie.
PLAYER BUS CABLE CONNECTOR (If equipped.)
47. Secure the excess length of DIN cable and XM radio harness to the vehicle harness with two wire ties. 48. If the vehicle is not equipped with a player, attach the two grommet screws to the player panel in the square holes as shown.
PLAYER PANEL
6 mm FLANGE NUTS (4) 3618021M
44. Install the display module assembly onto the studs from the left and right player subbrackets, and install the 6 mm flange nuts. Tighten the flange nuts securely.
14 of 22
GROMMET SCREW
AII 25749 (0402)
2306131T
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
49. Get one EPT sealer. Measure the EPT sealer as shown, and cut it into three pieces. EPT SEALER (Cut off the marked area.)
52. Inside the passengers' compartment, remove the rear seat cushion by removing the bolt and releasing the two locks (pull the lock out toward you).
PLAYER PANEL
BOLT
8 mm
REAR SEAT CUSHION
8 mm EPT SEALER
HOOKS (2) (Pull down.)
2612010T 2527020T
LOCKS (2)
50. Using isopropyl alcohol on a shop towel, clean the player panel in the area shown. Attach the two cut pieces of the EPT sealer to the player panel, and cut off the excess. 51. Attach the player panel by inserting the clips into the latches, and install two self-tapping screws from the kit, or reinstall the two self-tapping screws you removed in step 13. Remove the masking tape.
CLIP
LEVERS (2) (Pull out.)
53. Inside the trunk, fold the right and left seatbacks down by pulling the strap and pushing forward on the seat.
LEFT REAR SEAT CUSHION
STRAP
LATCH
PLAYER PANEL
SELFTAPPING SCREW (Reuse.)
2306141T 2527030T
RIGHT REAR SEAT BACK
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
AII 25749 (0402)
15 of 22
54. Remove the spare tire cover (one clip).
56. Remove the jack cover and the jack.
CLIP JACK SPARE TIRE COVER
JACK COVER 2527051T 3730010M
55. Remove the trunk weatherstrip in the area shown, then remove the rear trim panel (four clips).
57. Remove the hook from the right side trunk liner (one bolt , hook and washer). WASHER
CLIPS (4)
REAR TRIM PANEL
HOOK
RIGHT SIDE TRUNK LINER
THREADED HOOK
BOLT CLIP
TRUNK WEATHERSTRIP (Remove.) SELF-TAPPING HOOKS (3)
2527061T
2527073T
58. Remove the right side trunk liner (three selftapping hooks, one threaded hook and one clip).
16 of 22
AII 25749 (0402)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
58. Inside the trunk area, unplug the high mount brake light harness connector. Inside the cabin, remove the high mount brake light from the rear shelf by releasing the four hooks, and pulling out the brake light assembly. Take care not to damage the clips.
60. Raise the rear seat back. Pull the XM radio harness and DIN cable out from under the floor carpet and toward the passengers' side of the vehicle. Secure the XM radio harness and the DIN cable to the vehicle harness with two wire ties. DIN CABLE
HIGH-MOUNT BRAKELIGHT HOOKS (4) REAR SHELF VEHICLE CLIP XM RADIO HARNESS
BULB (If necessary.) 3620010M
CONNECTOR
WIRE TIE 3619060M
59. Route the XM radio harness and the DIN cable along the vehicle harness toward the parking brake lever, and under the floor carpet. Secure the XM radio harness and the DIN cable to the vehicle harness with two wire ties in the areas shown.
XM RADIO HARNESS AND DIN CABLE
WIRE TIE
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
3609010M
AII 25749 (0402)
17 of 22
61. Continue routing the XM radio harness and DIN cable along the vehicle harness toward the trunk. Using isopropyl alcohol, clean the areas where the cushion tapes will attach, then secure the XM radio harness and DIN cable to the vehicle panel with five cushion tapes.
63. Inside the trunk, install the two wire ties with clip to the DIN cable, and XM radio harness, and push the clips into the holes in the bulkhead. WIRE TIE WITH CLIPS (2) CUSHION TAPE
BULKHEAD
CUSHION TAPE
BULKHEAD HOLES (2) CABLE
CUSHION TAPES (5)
3620021M
62. Using isopropyl alcohol, clean the bulkhead area where the cushion tape will attach. To prevent damage to the XM radio harness and DIN cable, attach the cushion tape to the bulkhead edge in the area shown.
BULKHEAD
XM RADIO HARNESS
3620031M
64. Using isopropyl alcohol on a shop towel, clean the area where the cushion tape will attach. Attach the DIN cable and XM radio harness to the vehicle frame with one cushion tape. Installing the Antenna 65. Get the antenna kit. Route the antenna cable into the trunk area through the high-mount brakelight opening. Clean the edge of the rear shelf, and attach one cushion tape to the edge of the rear shelf. REAR SHELF CUSHION TAPE ANTENNA
ANTENNA CABLE
HIGH-MOUNT BRAKELIGHT OPENING
18 of 22
AII 25749 (0402)
3619111M
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
66. Temporarily fit the high-mount brake light onto the rear shelf.
69. Route the antenna cable through the groove in the high mount brake light case, and reinstall the high mount brake light case.
HIGH-MOUNT BRAKE LIGHT CASE
HIGH-MOUNT BRAKE LIGHT CASE
REAR TRAY BRAKE LIGHT OPENING CASE
GROOVE
ANTENNA ANTENNA CABLE
Clean with isopropyl
3627010M 3620043M
FRONT
Align
FASTENER
70. Route the antenna cable along the vehicle harness, and secure it to the vehicle harness with seven wire ties in the areas shown.
67. Using isopropyl alcohol on a shop towel, clean the bottom of the antenna. Remove the adhesive backing from the fastener, then attach the fastener to the bottom of the antenna. Attach the antenna onto the rear rear shelf.
VEHICLE HARNESS
WIRE TIES (7) (Attach near the vehicle harness clips.)
68. Measure and mark the high-mount brake light case. Using a utility knife, cut a groove in the brake light case. Remove any burrs from the edges of the groove.
BRAKELIGHT CASE Cut. 5 mm ANTENNA CABLE
10 mm 90 mm
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
VEHICLE HARNESS CLIP
3620050M
3619071M
AII 25749 (0402)
19 of 22
71. Attach one wire tie with clip to the antenna cable, the XM radio harness and the DIN cable in the area shown. Push the clip from the wire tie with clip into the body hole.
BODY HOLE
WIRE TIE WITH CLIP
72. Route the antenna cable, the XM radio harness, and the DIN cable along the trunk side panel. Loosely attach the three off-set wire ties with clip around the antenna cable, the XM radio harness, and the DIN cable, then push the clip from each wire tie into the three holes in the trunk side panel. TRUNK SIDE PANEL HOLE
ANTENNA CABLE DIN CABLE AND XM RADIO HARNESS
OFF-SET WIRE TIE WITH CLIP (Note the installation direction.) PANEL EDGE
EPT SEALER (Clean this surface with isopropyl alcohol.)
DIN CABLE XM RADIO HARNESS
TRUNK SIDE PANEL
ANTENNA CABLE
3620060M
ANTENNA CABLE
DIN CABLE
OFF-SET WIRE TIE WITH CLIP (2) (Note the installation direction.)
TRUNK SIDE PANEL HOLE
XM RADIO HARNESS 3620071M
73. Using isopropyl alcohol on a shop towel, clean the bonding surface on the panel edge, attach one EPT sealer to the panel edge in the area shown.
20 of 22
AII 25749 (0402)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
74. Install the upper and lower unit brackets to the receiver unit using two 4 x 8 mm washer-screws, and two 4 mm flange nuts for each bracket.
4 mm FLANGE NUT
76. Secure the antenna cable, the XM radio harness, and the DIN cable with two wire ties with clip at the measurement shown. Press the clips of the wire ties into the trunk side panel hole and upper unit bracket hole.
4 mm FLANGE NUT SCREW POSITION SCREW POSITION
TRUNK SIDE PANEL HOLE
WIRE TIE WITH CLIPS (2)
ANTENNA CABLE
240 mm UPPER UNIT BRACKET
LOWER UNIT BRACKET
RECEIVER UNIT
4 x 8 mm WASHERSCREW
WIRE TIE WITH CLIP
4 x 8 mm WASHERSCREW
UPPER UNIT BRACKET HOLE
3623031M
– DIN CABLE LOWER UNIT BRACKET HOLE
75. Position the receiver unit between the right trunk side panel and the rear fender panel, and plug in the antenna cable connectors, the DIN cable connector, and the XM radio harness connector using the panel hole to access the receiver unit.
BLACK CONNECTOR DIN CABLE XM RADIO HARNESS
= 240 mm 3730020M
77. Fold the excess DIN cable, and secure it to the lower unit bracket with one wire tie with clip. 78 Attach the receiver unit/brackets using two 6 x 12 mm washer-bolts through the trunk side panel holes. Tighten the bolts securely.
ANTENNA CABLE
TRUNK SIDE PANEL HOLE
ANTENNA CABLE
DIN CABLE XM RADIO HARNESS
6 x 12 mm WASHERBOLT
RECEIVER UNIT
3619092M
3619080M
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
6 x 12 mm WASHERBOLTS (2)
AII 25749 (0402)
21 of 22
79. Fold any excess antenna cable, and wrap the excess cable with two EPT sealers. Secure the antenna cable to the XM radio harness with two wire ties in the areas shown. Tighten the off set wire ties you loosely installed in step72.
81. Attach the 5A fuse label over the No. 33 position on the fuse box cover. FUSE LABEL (5A)
FUSE BOX COVER
No.33
OFF SET WIRE TIE WITH CLIP
2219090T
82. Check that all wire harnesses and cables are routed properly and all connectors are plugged in.
XM RADIO HARNESS
83. Reinstall all removed parts. Check that all clips and fasteners are installed securely.
EPT SEALERS (2) ANTENNA CORD
84. Reconnect the negative cable to the battery.
WIRE TIE 3623012M
80. Install the 5A fuse provided into the No. 33 slot of the fuse box.
85. Enter the radio anti-theft code, and reset the customer's radio station presets. 86. Set the clock. 87. Set one of the radio station presets to FM 88.7, and check the operation of the XM radio. If necessary, use the XM radio Owner’s Manual supplied.
FUSE BOX FUSE (5A)
NOTE: Whenever the battery is disconnected, the driver’s window AUTO up function is disabled. 88. Do the driver's window AUTO up procedure: •
Start the engine. Push down on the driver’s window switch until the window is fully open.
•
Pull up on the driver’s window switch to close the window completely, and hold the switch for 2 seconds or more.
•
Test the window AUTO up function.
2219080T
22 of 22
AII 25749 (0402)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
