Transcript
INSTALLATION INSTRUCTIONS
Accessory
Application
DVD in-VEHICLE ENTERTAINMENT SYSTEM WITH SUNROOF
2006 RIDGELINE
Publications No.
AII 28609 Issue Date
FEB 2005
PARTS LIST Attachment Kit: P/N 08B23-SJC-100
DVD player bracket A
i-VES harness
DVD player bracket B
DIN cable “A” FM modulator bracket
DIN cable “B”
Template: without sunroof (Not used.)
Interior light harness Template: with sunroof
Sub-feeder cord Template A
Monitor gasket
Template B
2 Screws, 3 x 8 mm Monitor bracket Washer-screw, 5 x 12 mm
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
AII 28609 (0502)
08B23-SJC-1000-9A
1 of 26
2 Washer-screws, 5 x 16 mm
Monitor Kit (sold separately): P/N 08A23-2G1-010
Monitor console 2 Washer-screws, 5 x 25 mm
4 Washer-screws, 6 x 12 mm (Not used.)
DVD player
4 Stepped bolts, 5 mm
4 Square-head bolts
2 Headphones
4 Flange nuts, 4 mm Remote controller Flange nut, 5 mm
2 Cap nuts, 5 mm
FM modulator
2 Nuts, 3 mm Connector clip
4 Washer-screws, 5 x 8 mm
18 Wire ties
2 Screw caps
Long wire tie
Quick Reference Tag
10 Cushion tapes
Owner’s Manual
7 EPT sealers
2 of 26
AII 28609 (0502)
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
INSTALLATION
TOOL AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Utility knife Scissors Push-pin Isopropyl alcohol Shop towel Tape measure Drill 3 mm and 8 mm Drill bits 1-1/8" (28 mm) Hole saw Ratchet 5 mm, 8mm, and 10 mm Combination wrenches 8 mm, 10 mm, and 14 mm Sockets Tape Masking tape Torque wrench T25 Torx wrench Diagonal cutters Eye protection (face shield, safety goggles, etc.)
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 1.
Make sure you have the anti-theft code for the radio, then write down the radio station presets.
2.
Close the sunroof.
3.
Disconnect the negative cable from the battery.
4.
Insert a flat-tip screwdriver wrapped with a shop towel into the groove of the instrument panel and release two clips. Pull the instrument panel out toward you to release eighteen clips, and remove the instrument panel by unplugging the vehicle connectors. VEHICLE CONNECTOR
VEHICLE CONNECTOR
Illustration of the DVD i-VES installed in the Vehicle INSTRUMENT PANEL DIN CABLE “A” MONITOR CONSOLE
VEHICLE CONNECTOR
SHOP TOWEL
CLIPS (2) CLIPS (18) INTERIOR LIGHT HARNESS
i-VES HARNESS DIN CABLE “B”
FLAT-TIP SCREWDRIVER Insert into the groove.
3915101T
DVD PLAYER 4917091H
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
AII 28609 (0502)
3 of 26
5.
Remove the audio unit (five screws, and pull the audio unit out toward you, and unplug the vehicle connectors).
6.
Remove the driver’s console side trim (three retaining clips and one tab).
Without Navi
VEHICLE CONNECTOR
INSTRUMENT PANEL
AUDIO UNIT
TAB DRIVER’S CONSOLE SIDE TRIM
SCREWS (5)
RETAINING CLIPS (3)
3915010T
4606030T
7.
With Navi
VEHICLE CONNECTOR
INSTRUMENT PANEL
Remove the passenger’s console side trim (two retaining clips and one tab).
NAVIGATION UNIT
TAB
SCREWS (5) 4913010H
4 of 26
AII 28609 (0502)
RETAINING CLIPS (2)
PASSENGER’S CONSOLE SIDE TRIM
3915020T
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
8.
Remove the dashboard center lower cover:
9.
•
Remove the center pocket.
•
Remove the three self-tapping screws.
•
Release the five retaining clips and six retaining tabs, and pull out the dashboard center lower cover.
•
Unplug the vehicle connectors, and remove the dashboard center lower cover.
Remove the glove box: •
Open the glove box. Disconnect the damper arm.
•
Remove the stoppers (two retaining tabs for each stopper).
•
Remove the two screws. RETAINING TABS (2)
STOPPERS (2)
DAMPER ARM
VEHICLE CONNECTOR RETAINING CLIPS (3)
RETAINING TABS (6) SCREW
SELFTAPPING SCREWS (3)
SCREW GLOVE BOX
RETAINING CLIPS (2)
DASHBOARD CENTER LOWER COVER
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
CENTER POCKET
4606041T
3915034T
AII 28609 (0502)
5 of 26
10. Remove the right dashboard side cover (seven clips).
12. Remove the center console rear cover :
CLIPS (7)
•
Pull the center console rear cover out toward you to release eight clips.
•
Slide the vehicle console light connector and the vehicle connector, and remove the vehicle console light connector and the vehicle connector from the vehicle clips.
•
Unplug the vehicle console light connector and the vehicle connector.
VEHICLE CLIP VEHICLE CONSOLE LIGHT CONNECTOR
RIGHT DASHBOARD SIDE COVER
CLIPS (8)
4D09040H
11. Remove the front center tray (two clips and two hooks). HOOK CENTER TRAY
FRONT
CLIPS (2)
CENTER CONSOLE REAR COVER VEHICLE CONNECTOR
VEHICLE CLIP
4907020H
6 of 26
AII 28609 (0502)
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
13. Remove the vehicle console light and harness (two retaining tabs).
15. Remove the right front door sill trim (three clips and three retaining tabs).
RETAINING TABS (2)
RETAINING TAB RIGHT FRONT DOOR SILL TRIM
CLIPS (3)
RETAINING TAB
VEHICLE CONSOLE LIGHT VEHICLE CONSOLE LIGHT HARNESS FRONT CENTER CONSOLE
4D09050H 4913031H
16. Remove the right rear door sill trim (three clips and three retaining tabs).
14. Remove the center console (two bolts and two self-tapping screws).
RETAINING TAB
RIGHT REAR DOOR SILL TRIM
SELF-TAPPING SCREW
RETAINING TAB
CLIPS (3)
CENTER CONSOLE
FRONT BOLTS (2)
4D10010H 4907012H
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
AII 28609 (0502)
7 of 26
17. Pull away the weatherstrip from the B-pillar lower trim panel. Remove the right seat belt lower anchor bolt cover and remove the right seat belt lower anchor bolt. Remove the right B-pillar lower trim panel by pulling it out toward you as shown.
19. Remove the right rear grab rail screw covers (two retaining tabs for each cover). Remove the right rear grab rail (two screws). B-PILLAR UPPER TRIM PANEL FRONT
WEATHERSTRIP (Pull away.) FRONT
RIGHT REAR GRAB RAIL RIGHT B-PILLAR LOWER TRIM PANEL
SCREWS (2)
SCREW COVERS (2) RETAINING TABS (2) LOWER ANCHOR BOLT COVER RIGHT SEAT BELT LOWER ANCHOR BOLT
4D10020H
20. Pull away the weatherstrip from the right B-pillar upper trim panel. Remove the right B-pillar upper trim panel (two clips).
18. Remove the right seat belt upper anchor bolt cover (four retaining tabs). Remove the right front seat belt upper anchor bolt. RETAINING TABS (2)
4D10060H
CLIPS (2)
WEATHERSTRIP (Pull away.) FRONT
RIGHT SEAT BELT UPPER ANCHOR BOLT COVER RETAINING TABS (2)
FRONT
Pry out on both tabs. SMALL FLAT-TIP SCREW DRIVER
RIGHT SEAT BELT UPPER ANCHOR BOLT COVER
RIGHT SEAT BELT UPPER ANCHOR BOLT
8 of 26
RIGHT B-PILLAR UPPER TRIM PANEL
4D10030H
4D10050H
AII 28609 (0502)
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
21. Remove the right rear hook trim cover (four tabs). Remove the right rear hook trim (two self-tapping screws). RIGHT REAR HOOK TRIM COVER
23. Pull away the weatherstrip away from the passenger’s A-pillar. Remove the passenger’s A-pillar trim (two clips). CLIPS (2) PASSENGER’S A-PILLAR TRIM
RIGHT REAR HOOK TRIM
TABS (4)
SELF-TAPPING SCREW WEATHERSTRIP (Pull away.) 4703032T
FRONT 4D10040H
24. Remove the left and right lenses from the roof console (four retaining tabs for each lens).
22. Remove the passenger’s grab rail screw covers (two retaining tabs for each cover), then remove the passenger’s grab rail (two screws).
ROOF CONSOLE
RIGHT LENS
LEFT LENS SCREW COVER
RETAINING TABS (4)
RETAINING TAB SCREW COVER
4216040K
SCREW
PASSENGER’S RETAINING SCREW GRAB RAIL TAB
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
RETAINING TABS (4)
4703023T
AII 28609 (0502)
9 of 26
25. Open the console pocket lid and remove the four bolts. Unplug two vehicle connectors, and remove the roof console.
27. Remove the right sunvisor screw cover (four retaining tabs), and remove the right sunvisor (two torx screws and unplug the vehicle connector).
VEHICLE CONNECTOR
VEHICLE CONNECTOR RETAINING TABS (4)
ROOF CONSOLE
RIGHT SUNVISOR
CONSOLE POCKET
T25 TORX SCREW
SUNVISOR SCREW COVER
4703051T
BOLT
28. Using scissors, cut out the marked area from the template (with sunroof). Crease the template as shown.
4216050K
26. Remove the sunvisor holders by rotating them clockwise.
Cut out areas.
TEMPLATE (Crease.)
SUNVISOR HOLDERS (2)
4N03061H
4217011K
FLAT-TIP SCREWDRIVER
10 of 26
AII 28609 (0502)
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
29. Open the sunshade. Position the template on the headliner and align the cutout with the sunshade knob. Tape the template to the headliner using strips of masking tape.
31. Close the sunshade.
SUNSHADE (Close.)
NOTE: Template is positioned with sunroof closed and sunshade open. REAR INTERIOR LIGHT
TEMPLATE FRONT
MASKING TAPE
FRONT 4N03091H
SUNSHADE (Open.)
32. Using a utility knife, cut out the marked area of the headliner. SUNSHADE KNOB
MARK
HEADLINER Align the crease with the edge. 4N03071H
UTILITY KNIFE
30. Using a felt-tip pen, mark the headliner along the outer edges of the template. Remove the template.
TEMPLATE FRONT
HEADLINER
HEADLINER Cut out this area.
4N03101H
FELT-TIP PEN
FRONT 4N03081H
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
AII 28609 (0502)
11 of 26
33. Gently pull the headliner down to release three clips and five velcro fasteners. VELCRO FASTENERS (5)
35. Route the yellow label side of DIN cable “A” along the vehicle harness, and temporarily secure DIN cable “A” to the vehicle harness with one wire tie.
CLIPS (3)
WIRE TIE (Loosely fasten)
EPT SEALER Cut in half.
VEHICLE CLIP
VEHICLE HARNESS YELLOW LABEL
DIN CABLE “A”
350 mm
4915014H
HEADLINER 4913101H
34. Route DIN cable “A” up through the headliner from the passenger's A-pillar, and out through the opening in the headliner you made in step 32.
DIN CABLE “A” TERMINAL 250 mm
36. Using isopropyl alcohol on a shop towel, clean the area where the EPT sealer will attach. Using scissors, cut one EPT sealer in half. Wrap the EPT sealer half to DIN cable “A” in the area shown. 37. Route DIN cable “A” down behind the dashboard and towards the glove box opening. PASSENGER’S A-PILLAR OPENING
HEADLINER OPENING
DIN CABLE “A”
FRONT
12 of 26
YELLOW LABEL
VEHICLE FRAME
4913123H
AII 28609 (0502)
GLOVE BOX OPENING
DIN CABLE “A” 4D10070H
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
38. Inside the glove box opening, route DIN cable “A” along the vehicle harness and towards the driver’s side of the vehicle.
Routing the i-VES Harness and the DIN Cables 40. At the audio unit opening, route the i-VES harness and the white label end of DIN cable “B” along the vehicle harness from the audio unit opening toward the floor of the vehicle .
VEHICLE HARNESS
i-VES HARNESS
AUDIO UNIT OPENING GLOVE BOX OPENING
DIN CABLE “A”
VEHICLE FRAME
4D10080H
39. Route DIN cable “A” to the audio unit opening, and down towards the floor vehicle.
WHITE LABEL DIN CABLE “B”
AUDIO UNIT OPENING
DIN CABLE “A”
4915035H
CENTER LOWER COVER OPENING
41. Route the i-VES harness, DIN cable “A” and DIN cable “B” toward the rear of the vehicle.
VEHICLE HARNESS DIN CABLE “A”
4D10090H
DIN CABLE “B”
i-VES HARNESS
VEHICLE FRAME DIN CABLE “A”
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
AII 28609 (0502)
4915044H
13 of 26
42. Slide the center console cup holder forward, and slide the inner cover forward. Open the console cover.
45. To the prevent drilling through the inner panel, wrap tape around the end of a 3 mm and an 8 mm drill bit about 15-20 mm away from the tip. CENTER CONSOLE
CONSOLE COVER
MARK
INNER COVER
15-20 mm DRILL BIT (3 mm 8 mm)
CENTER CONSOLE
DRILL BIT
TAPE (Wrap tape around the drill bit)
DRILL 4915070H
CUP HOLDER 4915050H
43. Position template A on the center console at the location shown, and attach template A to the center console using strips of tape.
46. While wearing eye protection, drill an 8 mm hole at each marked point. Start with a 3 mm drill bit and finish with an 8 mm drill bit. Remove any burrs from each hole. 47. Position template B on the center console at the location shown, and tape the template to the center console.
TEMPLATE A
PUSH-PIN
MARKS (3) TAPE TAPE TEMPLATE B CENTER CONSOLE
PUSH-PIN
4915060H
CENTER CONSOLE
44. Using a push-pin, mark the center console at the marks on the template. Remove the template.
4915080H
48. Using a push-pin, mark the center console at the marks on the template. Remove the template.
14 of 26
AII 28609 (0502)
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
49. While wearing eye protection, drill an 8 mm hole at each marked point. Start with a 3 mm drill bit and finish with an 8 mm drill bit. Use the drill bit with the tape attached.
52. Plug in the vehicle connectors, and install the vehicle connector in the vehicle clip. Route the vehicle console light harness through the console light opening.
HOLE SAW VEHICLE CONSOLE LIGHT HARNESS DRILL CONSOLE LIGHT OPENING
DRILL BIT (3 mm 8 mm) 1-1/8" (28 mm) HOLE SAW
CENTER CONSOLE CENTER CONSOLE REAR COVER
MARKS (3) CENTER CONSOLE 4915091H
50. Using a 1-1/8" (28 mm) hole saw, enlarge the center 8 mm hole to 1-1/8" (28 mm). Remove any burrs from each hole. 51. Reposition the center console in place. Route the i-VES harness, and DIN cables “A” and “B” through the 28 mm hole.
VEHICLE CONNECTOR
VEHICLE CLIP
Installing the DVD Player 53. Slide the DVD player into DVD player bracket A.
DVD PLAYER
i-VES HARNESS DIN CABLE “B”
DVD PLAYER BRACKET A DIN CABLE “A”
CENTER CONSOLE
28 mm HOLE
4915101H
AUXILIARY INPUT JACKS 4909020H
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
AII 28609 (0502)
15 of 26
54. Secure the auxiliary input jacks from the DVD player to DVD player bracket B with two 3 x 8 mm screws and two 3 mm nuts.
56. Install the vehicle console light to DVD player bracket A as shown.
VEHICLE CONSOLE LIGHT HARNESS
3 mm NUT
DVD PLAYER BRACKET A
AUXILIARY INPUT JACKS
3 x 8 mm SCREW
VEHICLE CONSOLE LIGHT
VEHICLE CONSOLE LIGHT
DVD PLAYER BRACKET B
4909030H
55. Secure DVD player bracket B to DVD player bracket A with one 5 x 12 mm washer-screw and one 5 mm flange nut. DVD PLAYER BRACKET A
RETAINING TABS (2)
DVD PLAYER BRACKET A
4909051H
57. Secure the DVD player to DVD player bracket A and B with three 5 x 8 mm washer-screws included with the Monitor Kit.
5 mm FLANGE NUT
CONNECTOR CLIP
DVD PLAYER BRACKET A CENTER CONSOLE LIGHT CONNECTOR DVD PLAYER BRACKET B
DVD PLAYER BRACKET B
5 x 12 mm SCREW
4909040H
5 x 8 mm WASHERSCREWS (3) (Included with the Monitor Kit.)
CONNECTOR CLIP
4909062H
58. Install the connector clip to the vehicle console light connector, and secure the vehicle console light connector to DVD player bracket B.
16 of 26
AII 28609 (0502)
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
59. Slide the DVD player into the center console.
61. Secure DVD player bracket A to the center console with two 5 mm stepped bolts and two 5 mm cap nuts.
DVD PLAYER 5 mm CAP NUTS (2)
CENTER CONSOLE
5 mm STEPPED BOLTS (2) 4915141H
CENTER CONSOLE DVD PLAYER BRACKET A
60. Plug the i-VES harness 4-pin connector, DIN cable “A” and “B” and the vehicle console light connector into the rear of the DVD player.
4916020H
62. Lift the center console as shown, and secure DVD player bracket A to the center console with two 5 mm stepped bolts.
CONSOLE LIGHT CONNECTOR DVD PLAYER
8 mm HOLE
i-VES HARNESS 4-PIN CONNECTOR CENTER CONSOLE
DIN CABLE “B” YELLOW LABEL DIN CABLE “A”
4916013H
FRONT
5 mm STEPPED BOLT
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
AII 28609 (0502)
4916030H
17 of 26
63. Using isopropyl alcohol on a shop towel, clean the areas where the cushion tapes will attach. Lift the center console, then secure the i-VES harness and the DIN cables to the vehicle panel with two cushion tapes as shown.
66. Secure the i-VES harness and the DIN cables to the vehicle harness with two wire ties in the areas shown.
CENTER CONSOLE
FRONT
VEHICLE HARNESS
WIRE TIE FRONT
i-VES HARNESS VEHICLE PANEL
CUSHION TAPE
DIN CABLE “B”
CUSHION TAPE DIN CABLE “A”
DIN CABLE “A”
DIN CABLE “B” VEHICLE BRACKET
4916041H
i-VES HARNESS
4916062H
67. At the audio unit opening, secure the i-VES harness and DIN cable “B” to the vehicle harness with one wire tie in the area shown. i-VES HARNESS
64. Reinstall the center console. 65. Pull back the floor carpet. Using isopropyl alcohol on a shop towel, clean the areas where the cushion tapes will attach. Secure the i-VES harness and the DIN cables to the vehicle panel with two cushion tapes as shown.
DIN CABLE “B”
AUDIO UNIT OPENING
VEHICLE HARNESS
WIRE TIE
FRONT
CUSHION TAPE
VEHICLE PANEL
FLOOR CARPET (Pull back.) 4D26011H
i-VES HARNESS
CUSHION TAPE DIN CABLE "A" DIN CABLE "B"
18 of 26
4916052H
AII 28609 (0502)
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
68. At the audio unit opening, plug the i-VES harness 20-pin connector into the vehicle 20-pin connector, and secure the 20-pin connectors with one long wire tie. i-VES HARNESS 20-PIN CONNECTOR
LONG WIRE TIE
70. Secure DIN cable “A” to the vehicle harness with two wire ties in the areas shown. AUDIO UNIT OPENING WIRE TIE
AUDIO UNIT OPENING
DIN CABLE “B”
VEHICLE HARNESS
i-VES HARNESS
DIN CABLE “A”
VEHICLE 20-PIN CONNECTOR 4916070H
4D13040H
71. At the glove box opening, secure DIN cable “A” to the vehicle harness with three wire ties.
69. Secure the i-VES harness and DIN cable “B” to the vehicle harness with two wire ties in the areas shown.
VEHICLE HARNESS
WIRE TIE
GLOVE BOX OPENING WIRE TIE
DIN CABLE “A”
4D13050H
DIN CABLE “B” VEHICLE HARNESS
i-VES HARNESS 4916080H
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
AII 28609 (0502)
19 of 26
72. Using isopropyl alcohol on a shop towel, clean the area where the cushion tape will attach. Secure DIN cable “A” to the vehicle panel with one cushion tape. VEHICLE CLIP
75. Route the interior light harness between the headliner and insulator from the interior light opening out the headliner opening.
INTERIOR LIGHT HARNESS
WIRE TIE (2)
VEHICLE HARNESS
INSULATOR
DIN CABLE “A”
INTERIOR LIGHT OPENING
HEADLINER DIN CABLE “A” CUSHION TAPE
HEADLINER OPENING VEHICLE PANEL
VEHICLE 3-PIN CONNECTOR
WIRE TIE (Fasten securely)
VEHICLE FRAME
INTERIOR LIGHT HARNESS 3-PIN CONNECTOR
4916102H
FRONT
73. Secure DIN cable “A” to the vehicle harness with two wire ties, and tighten the wire tie you temporarily secured to DIN cable “A” in step 35.
76. Plug the interior light harness 3-pin connector into the vehicle 3-pin connector.
74. Remove the rear interior light. •
Remove the two lenses (four tabs on each lens).
•
Remove the two self-tapping screws.
•
Unplug the vehicle 3-pin connector.
4916122H
77. Using isopropyl alcohol on a shop towel, clean the area where the cushion tape will attach. Using scissors, cut one cushion tape in half. Secure the interior light harness to the headliner with the cushion tape half.
VEHICLE 3-PIN CONNECTOR
INTERIOR LIGHT OPENING CUSHION TAPE Cut in half. REAR INTERIOR LIGHT
CUSHION TAPE
HEADLINER OPENING
SELF-TAPPING SCREWS (2) TABS (4)
FRONT
FRONT
LENS
FOAM INTERIOR LIGHT HARNESS HEADLINER 3-PIN CONNECTOR
4916111H
78. Position the 3-pin connector in the cavity in the headliner. Reinstall the rear interior light.
20 of 26
AII 28609 (0502)
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
79. Using isopropyl alcohol on a shop towel, clean the areas where the cushion tapes will attach. Using scissors, cut three cushion tapes in half. Secure DIN cable “A” to the headliner with the six pieces of cushion tape.
81. With the sunshade in the closed position, insert four square-head bolts through the holes in the vehicle frame. VEHICLE FRAME HEADLINER OPENING
CUSHION TAPES (3) Cut in half. 250 mm
HEADLINER OPENING
SQUARE-HEAD BOLTS (4) FRONT 4N03121H
DIN CABLE “A” FRONT 4916161H
82. Secure the monitor bracket to the vehicle frame with four 4 mm flange nuts and the four squarehead bolts you inserted.
Installing the Monitor Console 80. Using isopropyl alcohol on a shop towel, clean the areas where the EPT sealers will attach. Using scissors, cut two EPT sealers in half. Attach the EPT sealer halves, and one EPT sealer to the monitor bracket in the areas shown. Cut the excess off the EPT sealers.
VEHICLE FRAME
SQUARE-HEAD BOLTS (4)
MONITOR BRACKET
EPT SEALERS (2) Cut in half.
EPT SEALER Cut off. SQUARE-HEAD BOLTS (4)
FRONT MONITOR BRACKET
4 mm FLANGE NUT
4N03141H
Cut off. 4N03111H
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
AII 28609 (0502)
21 of 26
83. Remove the left and right lenses from the monitor console, then install the monitor gasket on the console while aligning the mark of the monitor gasket with the mark on the monitor console. MONITOR CONSOLE
85. While holding the monitor console, secure the 3-pin connector and the terminal to the back of the monitor console with one cushion tape.
LEFT LENS FRONT
RIGHT LENS
3-PIN CONNECTOR
MONITOR CONSOLE TERMINAL
MONITOR GASKET
MARK 2326290T
84. Remove the tape that secures the 3-pin connector to the monitor console. Connect the interior light harness 3-pin connector and DIN cable “A” terminal into the monitor console 3-pin connector and monitor console terminal.
DIN CABLE “A” TERMINAL
INTERIOR LIGHT 3-PIN CONNECTOR
TAPE
MONITOR CONSOLE TERMINAL
CUSHION TAPE 4917041H
86. Position the monitor console on the monitor bracket, and install two 5 x 16 mm washer-screws and two 5 x 25 mm washer-screws. Install two screw caps, then reinstall the left and right lenses. Do not pinch the DIN cable “A” between the monitor console and monitor bracket.
MONITOR CONSOLE HARNESS
MONITOR CONSOLE
MONITOR BRACKET
5 x 25 mm WASHER SCREW MONITOR CONSOLE 3-PIN CONNECTOR FRONT
MONITOR CONSOLE
4N03151H
LEFT LENS
FRONT
22 of 26
AII 28609 (0502)
RIGHT LENS
5 x 16 mm WASHER SCREW SCREW CAPS (2)
4D21020H
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
87. Secure the FM modulator bracket to the FM modulator with one 5 x 8 mm washer-screw included with the monitor kit. FM MODULATOR
89. Using isopropyl alcohol on a shop towel, clean the area where the EPT sealer will attach. Attach one EPT sealer half that you cut into two in step 88 to the audio unit/navigation unit.
FM MODULATOR BRACKET
Without Navi
AUDIO UNIT
5 x 8 mm WASHER-SCREW (Included with the monitor kit.) 4917021M
88. Set the FM modulator switch at 88.5. Using isopropyl alcohol on a shop towel, clean the area where the EPT sealer will attach. Using scissors, cut one EPT sealer in half. Secure the FM modulator cables to the FM modulator with one EPTsealer half.
EPT SEALER Cut in half in step 88.
4917030M
SWITCH
EPT SEALER Cut in half.
With Navi NAVIGATION UNIT
FM MODULATOR
FM MODULATOR CABLE
4917052M
EPT SEALER Cut in half in step 88. 4917040M
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
AII 28609 (0502)
23 of 26
90. Remove two screws from the audio unit/navigation unit. Secure the FM modulator bracket to the audio unit/navigation unit with the two screws you removed.
91. Plug the sub-feeder antenna leads into the FM modulator antenna leads. Plug the sub-feeder 2-pin connector into the audio unit/navigation unit.
Without Navi
Without Navi AUDIO UNIT FM MODULATOR ANTENNA LEAD
AUDIO UNIT
FM MODULATOR BRACKET
FM MODULATOR
SUB-FEEDER 2-PIN CONNECTOR
SCREW SUB-FEEDER ANTENNA LEAD
4917060M
4917080M
With Navi
With Navi
2-PIN CONNECTOR LOCATION
NAVIGATION UNIT
FM MODULATOR BRACKET
FM MODULATOR ANTENNA LEAD NAVIGATION UNIT
FM MODULATOR
SCREW
SUB-FEEDER 2-PIN CONNECTOR SUB-FEEDER ANTENNA LEAD
4917070M
4917090M
24 of 26
AII 28609 (0502)
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
92. Using scissors, cut two EPT sealers in half. Wrap the two half EPT sealer halves around the respective antenna leads as shown.
93. Plug the vehicle antenna connector into the sub-feeder antenna 2-pin connector.
Without Navi
Without Navi AUDIO UNIT AUDIO UNIT
FM MODULATOR
i-VES HARNESS 20-PIN CONNECTOR
ANTENNA LEADS
VEHICLE ANTENNA CONNECTOR
DIN CABLE “B” TERMINAL
SUB-FEEDER ANTENNA 2-PIN CONNECTOR
EPT SEALER Cut in half.
4917120M
With Navi EPT SEALER Cut in half.
4917100M
20-PIN CONNECTOR LOCATION
With Navi
FM MODULATOR NAVIGATION UNIT
NAVIGATION UNIT
i-VES HARNESS 20-PIN CONNECTOR
ANTENNA LEADS
VEHICLE ANTENNA CONNECTOR
SUB-FEEDER ANTENNA 2-PIN CONNECTOR
DIN CABLE “B” TERMINAL 4917130M
EPT SEALER Cut in half. EPT SEALER Cut in half.
4917110M
94. Plug DIN cable “B” terminal into the FM modulator. 95. Plug the i-VES harness 20-pin connector into the audio unit/navigation unit. 96. Reinstall the audio unit/navigation unit.
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
AII 28609 (0502)
25 of 26
97. Insert the Quick Reference Tag into the center console.
QUICK REFERENCE TAG
CENTER CONSOLE 4N11041H
98. Check that all wire harnesses are routed properly and all connectors are plugged in. 99. Reconnect the negative cable to the battery. 100. Enter the customer’s radio anti-theft code, and reset the radio station presets. 101.Reset the clock, and reset the radio station presets. 102. Check the operation of the in-Vehicle Entertainment System according to the Owner’s Manual provided. 103. Put the in-Vehicle Entertainment System Owner’s Manual in the glove box with the vehicle owner’s manual. 104. Reinstall all removed parts. Torque the seat belt anchor bolts to 30 to 35 N·m (21 to 25 lbf·ft) NOTE: Whenever the battery is disconnected, the driver’s AUTO function is disabled. 105.Start the engine. Push down on the driver’s window switch until the window is fully open. 106.Pull up on the driver’s window switch fully to close the window completely, then hold the switch for 2 seconds or more. 107.Test the window AUTO function.
26 of 26
AII 28609 (0502)
© 2005 American Honda Motor Co., Inc - All Rights Reserved.
