Preview only show first 10 pages with watermark. For full document please download

Alamo Hydro 60 Hydro 72 Mower Parts Manual

   EMBED


Share

Transcript

HYDRO 60 & 72 ROTARY MOWERS Published 07- 05 Part No. 02965002P PARTS MANUAL An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or Alamo Industrial (830-379-1480) to obtain a Free copy before operating the equipment. Alamo Industrial 1502 E. Walnut Seguin, Texas 78155 830-379-1480 © 2005 Alamo Group Inc. TO THE OWNER/OPERATOR/DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it to within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. PARTS SECTION Parts Section -1 © 2005 Alamo Group Inc. PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number, and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. NOTE: Please refer to The Safety Section in the front of this Manual for the proper Part Number when ordering Replacement Safety Decals. NOTE: Please note that the appearance of some parts may vary from the art or photographs shown in the manual. For maximum safety and to guarantee optimum product reliability, always use genuine Alamo Group Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to: Alamo Industrial 1502 E. Walnut Seguin, Texas 78155 830-379-1480 PARTSGo PARTS 6. The Manufacturer reserves the right to change prices without prior notice. Hydro 60 & 72 (07/05) © 2005 Alamo Group Inc. Parts Section - 2 PART NAME INDEX A-FRAME ASSEMBLY ........................................................................................................................................................... 4 CASTER WHEEL ASSEMBLY ............................................................................................................................................. 30 FILTER ASY. P/N 02964748 .................................................................................................................................................. 6 FRONT CHAINGUARD ........................................................................................................................................................ 32 HOSE SCHEMATIC.............................................................................................................................................................. 34 HYDRAULIC PUMP REPAIR PARTS P/N 02964947.......................................................................................................... 22 HYDRAULIC PUMP W/ FITTINGS P/N 02965003 .............................................................................................................. 21 HYDRAULIC TANK ASSEMBLY ............................................................................................................................................ 5 MANIFOLD ASSEMBLY P/N 02964747................................................................................................................................. 7 MOTOR & SPINDLE HOUSING ASSEMBLY ........................................................................................................................ 8 PUMP & SPEED INCREASER ASSEMBLY ........................................................................................................................ 27 REAR CHAINGUARD........................................................................................................................................................... 33 SKID SHOE .......................................................................................................................................................................... 31 SPEED INCREASER P/N 00768991 ( 540 RPM ) NEW STYLE ........................................................................................ 23 SPEED INCREASER REPLACEMENT PARTS P/N 02897900 OLD STYLE ..................................................................... 25 SPINDLE HOUSING & SPINDLE ASY. P/N 02960553C .................................................................................................... 15 60" BLADE BAR ASSEMBLY............................................................................................................................................... 18 60" BLADE PAN ASY. P/N 02964456.................................................................................................................................. 17 60" HYDRAULIC MOTOR ASY. P/N 02961747................................................................................................................... 10 60" HYDRAULIC MOTOR W / FITTINGS .............................................................................................................................. 9 60" STANDARD BLADE PAN ASY. P/N 02965127............................................................................................................. 16 60" TAIL WHEEL ASSEMBLY.............................................................................................................................................. 28 72" BLADE BAR ASSEMBLY............................................................................................................................................... 19 72" HYDRAULIC MOTOR ASY. P/N 02969725................................................................................................................... 13 72" HYDRAULIC MOTOR W / FITTINGS ............................................................................................................................ 12 72" STUMP JUMPER PAN ASY. P/N 02963382 ................................................................................................................. 20 72" TAIL WHEEL ASSEMBLY.............................................................................................................................................. 29 HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 3 A-FRAME ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 02964520 00768896 02964535 2196 02967130 00768897 7AH5101118 00695100 02960916 00037200 02974850 1 4 2 2 1 1 4 4 2 2 2 A-FRAME, WLD’MT SHACKLE - 2 REQ.FOR 41" OFFSET LIFT PIN, WLD’MT PIN CLIP CHAIN 5/8 - 60" CHAIN 5/8 - 72" HEX BOLT LOCKNUT BOLT LOCKNUT SHACKLE FOR 41" OFFSET 6 7 8 9 10 HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 4 HYDRAULIC TANK ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 --- 02964650 03200350 00759220 02967127 02049700 02960408 02963659 02964747 00059900 02964656 02964657 00753642 00015800 02964748 00600500 02049500 02964749 02961452 00751530 02961001 02972678 02973782 02978349 02978354 02978355 1 1 1 1 1 1 1 1 2 1 1 5 7 1 4 4 1 1 1 1 1 1 1 1 1 HYDRAULIC TANK, WLD’MT FILLER PLUG BREATHER VALVE O-RING SIGHT, GLASS ELBOW MAGNETIC PLUG MANIFOLD ASY. BOLT MOUNT MOUNT BOLT LOCKNUT FILTER HOUSING ASY*. BOLT LOCKWASHER RETAINER O-RING FILTER ELEMENT FILTER ELEMENT SPRING FILTER CARTRIDGE VALVE FILTER BYPASS FILTER COVER SEAL KIT NUT AND BOLT KIT HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 5 FILTER ASY. P/N 02964748 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 02964748 02961001 02972678 02973782 02978349 02978354 02978355 -1 1 1 1 1 1 FILTER ASY. W/ ELEMENT FILTER ELEMENT ONLY SPRING FILTER CARTRIDGE VALVE, FILTER BYPASS FILTER COVER SEAL KIT NUT & BOLT KIT, F/ FILTER COVER. HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 6 MANIFOLD ASSEMBLY P/N 02964747 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 00751791 02287000 02960405 02957228 1 1 2 1 RELIEF VALVE - 2500 PSI MANIFOLD BLOCK STRAIGHT ADAPTER HYD - ELBOW HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 7 MOTOR & SPINDLE HOUSING ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 02960951 00001800 02788400 02971038 02971747 02969725 02960553C 00037200 02959390 00003901 02886600 -------------02958575 2 6 2 1 1 1 1 6 4 4 4 1 1 DOUBLE END STUD LOCKNUT BOLT GASKET MOTOR - 60" MOTOR - 72" SPLINED SPINDLE ASY. LOCKNUT BOLT LOCKWASHER BOLT PAN ASY. - 60" BLADE BAR CARRIER ASY. - 72" 6 7 8 9 10 11 HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 8 60" HYDRAULIC MOTOR W / FITTINGS ITEM PART NO. QTY. DESCRIPTION 1 2 3 02961747 02961028 00749101 1 2 2 HYDRAULIC MOTOR HYD, ELBOW SPLIT FLANGE KIT HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 9 60" HYDRAULIC MOTOR ASY. P/N 02961747 HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 10 60" HYDRAULIC MOTOR ASY. P/N 02961747 ITEM PART NO. QTY. DESCRIPTION 1 2*+ 3 4*+ 5 6 7 8*+ 9* 10 11* 12 13 14 15 16 17* 18 19 20 02962200 --------------02962199 --------------02962192 02961940 02961931 --------------------------02962195 -------------+ 02962201 02962194 02962193 02962196 02962197 --------------+ 02962291 02962202* 02962540+ 1 1 1 2 1 1 2 4 2 1 2 4 1 1 4 4 4 1 REF. REF. SNAP RING "O"RING RETAINER SEAL SEAL MOUNTING FLANGE, W / BUSHING PLUG CHECK ASY. SEAL END THRUST PLATE GEAR SET SQUARE SEAL DOWEL PIN GEAR HOUSING PORTING FLANGE, W / BUSHING WASHER BOLT SIDE SEAL ( NOT SHOWN ) RETAINER SEAL MAJOR SEAL KIT - INC.2,4,8,11,&17 MINOR SEAL KIT - INC.2,4,8,9,11,& 17 HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 11 72" HYDRAULIC MOTOR W / FITTINGS ITEM PART NO. QTY. DESCRIPTION 1 2 3 02969725 02961028 00749101 1 2 2 HYDRAULIC MOTOR HYD, ELBOW SPLIT FLANGE KIT HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 12 72" HYDRAULIC MOTOR ASY. P/N 02969725 HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 13 72" HYDRAULIC MOTOR ASY. P/N 02969725 ITEM PART NO. QTY. DESCRIPTION 1 2*+ 3 4*+ 5 6 7 8*+ 9* 10 11* 12 13 14 15 16 17* 18 19 20 02962200 --------------02962199 --------------02962192 02961940 02961931 --------------------------02969863 -------------+ 02962201 02969862 02962193 02962196 02969864 --------------+ 02962199 02962202* 02962540+ 1 1 1 2 1 1 2 4 2 1 2 4 1 1 4 4 4 1 REF. REF. SNAP RING "O"RING RETAINER SEAL SEAL MOUNTING FLANGE W / BUSHING PLUG CHECK ASSEMBLY SEAL END THRUST PLATE GEAR SET SQUARE SEAL DOWEL PIN GEAR HOUSING PORTING FLANGE W / BUSHING WASHER BOLT SIDE SEAL ( NOT SHOWN ) RETAINER SEAL MAJOR SEAL KIT - INC.2,4,8,11,&17 MINOR SEAL KIT - INC.2,4,8,9,11,& 17 HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 14 SPINDLE HOUSING & SPINDLE ASY. P/N 02960553C ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 02961038 02960562C 02960561 02960558 02960559 00754627 02960557 00755628 02964269 02962030 00754634 02959860 1 1 1 1 1 1 1 1 1 1 1 1 GASKET HOUSING SPINDLE BEARING RING SEAL SNAP RING SPINDLE CUP & CONE ASY. BEARING LOCKWASHER LOCKNUT GREASE PLUG BREATHER PLUG HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 15 60" STANDARD BLADE PAN ASY. P/N 02965127 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 5JRC16140 9216 00758851 02886200 8227 2 2 1 2 2 LOCKNUT WASHER DISH PAN WLD"MT BLADE BLADE BOLT HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 16 60" BLADE PAN ASY. P/N 02964456 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 02964804 02975903 02964330 00020900 00755623 02964954 02964815 00023200 1 1 3 3 3 3 3 3 PAN ASSEMBLY BLADE SET BLADE BOLT NUT WASHER KEY BUSHING ROLL PIN HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 17 60" BLADE BAR ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 5JRC16140 9216 00758852 02886200 8227 2 2 1 2 2 LOCKNUT, 1" WASHER, 1" HARDENED BLADE BAR, W/ SQ BLADE BOLT HOLES BLADE BLADE BOLT, W/ SQ SHOULDER HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 18 72" BLADE BAR ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 00747900 00748000 02958577 02886200 00752827 2 2 1 2 2 LOCKNUT LOCKWASHER BLADE BAR, W/ ROUND KEYED HOLE BLADE BLADE BOLT, W/ ROUND SHOULDER & KEYED HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 19 72" STUMP JUMPER PAN ASY. P/N 02963382 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 02960612 00750787 00752827 00748000 00747900 00003901 02961298 1 2 2 2 2 4 REF 4 REF 72" STUMP JUMPER PAN, WLD’MT MATCHED BLADES - 72" BLADE BOLT LOCKWASHER LOCKNUT LOCKWASHER BOLT HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 20 HYDRAULIC PUMP W/ FITTINGS P/N 02965003 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 02964947 02961098 00749101 02026200 02964196 1 1 1 1 1 HYDRAULIC PUMP 90 DEG. ELBOW SPLIT FLANGE KIT HOSE CLAMP ELBOW - HOSE END FITTING HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 21 HYDRAULIC PUMP REPAIR PARTS P/N 02964947 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4* 5 6 7 8* 9* 10 11* 12 02961918 02961917 02961914 -------------02961913 02961920 02965092 --------------------------02965091 -------------02961924 4 4 1 2 1 1 1 4 2 1 2 4 BOLT WASHER PORTING FLANGE, W/ BUSHING SEAL MOUNTING FLANGE, W/ BUSHING PLUG GEAR HOUSING SEAL END THRUST PLATE GEAR SET SQUARE SEAL DOWEL PIN HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 22 SPEED INCREASER P/N 00768991 ( 540 RPM ) NEW STYLE HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 23 SPEED INCREASER P/N 00768991 ( 540 RPM ) NEW STYLE ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 00754519 00754520 00754521 00754522 00754523 00754524 00754525 00754526 00754527 00754528 00754529 00754530 00754531 00754532 00754533 00754534 00754535 00754536 00754537 00754538 00754539 00754540 00754541 00754542 00754543 00754544 00756532 00754545 00756531 00754546 00754950 02966731 00754951 1 1 1 1 1 4 3 3 8 10 10 2 1 1 1 1 1 5 4 2 1 1 3 1 2 1 1 1 1 1 1 REF. REF. HOUSING GASKET GASKET FLANGE BREATHER PLUG ALUMINUM WASHER PLUG LOCKWASHER BOLT LOCKWASHER BOLT DOWEL PIN HOUSING GASKET FLANGE GASKET DIPSTICK ALUMINUM WASHER PLUG DOUBLE LIP SEAL BEARING RETAINING RING BEARING SHAFT KEY GEAR - 540 RPM GEAR - 1000 RPM PINION GEAR - 540 RPM PINION GEAR - 1000 RPM SPACER PUMP FLANGE ADAPTER, 1" - 15 SPLINE ADAPTER, 7/8" - 13 SPLINE 27 28 29 30 HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 24 SPEED INCREASER REPLACEMENT PARTS P/N 02897900 OLD STYLE HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 25 SPEED INCREASER REPLACEMENT PARTS P/N 02897900 OLD STYLE ITEM PART NO. QTY. DESCRIPTION 1 2 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 24 25 26 27 28 29 30 31 32 33 34 35 36 02922700 00751531 00752179 02922600 00751949 00751950 00751970 00751535 00751954 00751942 00751951 00751533 00749201 00749200 00751953 00751955 00751956 00751957 00751958 00751971 00751959 00751960 00751961 00751962 00751963 00751964 00751965 00751966 00751967 00751968 00751969 00013901 00012101 1 1 1 1 1 2 8 3 1 1 1 1 3 3 1 1 1 2 1 2 AR AR AR 3 AR 1 AR AR 24 24 8 8 8 ADAPTER, 1-3/4"-13 SPLINE GEAR - 18 TEETH GEAR - 72 TEETH PUMP FLANGE COVER, CLOSED COVER, OPEN PIPE PLUG SEAL RETAINING RING BREATHER BEARING CUP BEARING CONE BEARING CUP BEARING CONE SPACER RING HOUSING HOUSING DOWEL PIN GASKET - .015 SPACER RING SHIM .005 ALUM SHIM .007 ALUM SHIM .020 ALUM SHIM .005 FIBRE SHIM .005 ALUM SHIM .005 FIBRE SHIM .007 ALUM SHIM .020 ALUM BOLT LOCKWASHER BOLT NUT LOCKWASHER HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 26 PUMP & SPEED INCREASER ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 00768991 02965003 02959661 00019600 02966731 1 1 2 2 1 SPEED INCREASER, 540 RPM W/OIL PUMP BOLT LOCKWASHER SPLINE ADAPTER ( NOT SHOWN ) HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 27 60" TAIL WHEEL ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 02964526 02964530 02964529 65107A4 371063A 00037200 02958035 00130010 15B1400 02957042 00015800 00008200 00001800 1 1 1 1 1 1 1 1 1 4 4 1 2 TUBE, WLD’MT MOUNT BRKT, WLD’MT TOP MOUNT PLATE GUIDE SPRING SPRING LOCKNUT BOLT TIRE & WHEEL ASY. WASHER BOLT LOCKNUT BOLT LOCKNUT HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 28 72" TAIL WHEEL ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 02965993 02966036 02966034 65107A4 371063A 00037200 00008200 00130010 00002701 02957042 00015800 02959302 00001800 1 1 1 2 2 2 1 1 2 4 4 1 2 TUBE, WLD’MT MOUNT BRKT, WLD’MT TOP MOUNT PLATE GUIDE SPRING SPRING LOCKNUT BOLT TIRE & WHEEL ASY. FLATWASHER BOLT LOCKNUT BOLT LOCKNUT HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 29 CASTER WHEEL ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 2 3* 4* 5 6 7 8 9 10 11 00156503 00752272 00013600 02817100 00130010 00748751 00695100 00749264 00749413 00742670 00752670 1 2 2 2 1 1 1 1 1 1 2 BOLT AXLE HUB SEAL BEARING ASY. - OFFSET MOWER TIRE & WHEEL ASY. CASTER FORK LOCKNUT COLLAR BOLT N/A GREASE FITTING HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 30 SKID SHOE ITEM PART NO. QTY. DESCRIPTION 1 02885600 02958663 02964557 02958663 00059700 00011100 00015800 1 1 1 1 11/12 11/12 11/12 SKID SHOE - 60" SKID SHOE - 72" SKID SHOE - 60" SKID SHOE - 72" BOLT FLATWASHER LOCKNUT 2 3 4 5 HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 31 FRONT CHAINGUARD ITEM PART NO. QTY. 60" QTY. 72" DESCRIPTION 1 2 00223900 02964571 02964839 00023100 00011100 00015800 02964697 00992000 00001000 36 1 -8 6 8 1 1 2 43 -1 10 8 10 1 1 2 CHAIN CHAINGUARD, WLD’MT CHAINGUARD, WLD’MT BOLT FLATWASHER LOCKNUT CORNER BRKT, WLD’MT CABLE CABLE CLAMP 3 4 5 6 7 8 HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 32 REAR CHAINGUARD ITEM PART NO. QTY. 60" QTY. 72" DESCRIPTION 1 2 00750900 02939700 02959044 00015800 00011100 00023100 02964697 00001000 00992000 36 1 -8 6 8 2 2 1 43 -1 8 6 8 2 2 1 CHAIN CHAIN GUARD BRKT. CHAIN GUARD BRKT. LOCKNUT FLATWASHER BOLT CORNER BRKT. WLD’MT CABLE CLAMP CABLE 3 4 5 6 7 8 HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 33 HOSE SCHEMATIC ITEM PART NO. QTY. DESCRIPTION 1 2 02964743 02964745 02512800 02964144 02961309 02964582 02961096 02964581 02966317 02964744 02966318 02964144 02964746 02961328 02961098 02964947 00768956 02964196 00749101 02960407 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 HYDRAULIC TANK ASY. SUCTION HOSE - 60" SUCTION HOSE - 72" HOSE - 60" HOSE - 72" HOSE - 60" HOSE - 72" HOSE - 60" HOSE - 72" HOSE - 60" HOSE - 72" HOSE - 72", W/ 35" OFFSET ONLY HOSE - 60" HOSE - 72" ADAPTER HYD. ELBOW - 90DEG PUMP SPEED INCREASER FITTING - HOSE END SPLIT FLANGE KIT ADAPTER HYD. ELBOW - 90DEG 3 4 5 6 7 8 9 10 11 12 13 HYDRO 60 & 72 ( 07 - 05 ) ©2005 Alamo Group Inc. Parts Section – 34 ALAMO INDUSTRIAL LIMITED WARRANTY 1. LIMITED WARRANTIES 1.01.Alamo Industrial warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”) that the goods purchased are free from defects in material or workmanship. 1.02.Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship. 1.03.This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found in your Operator’s Manual. 1.04.Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of Manufacturer. 2. REMEDIES AND PROCEDURES. 2.01.This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer within 30 days of purchase. 2.02.Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the claim is based. 2.03.Purchaser is responsible for returning the goods in question to the Dealer. 2.04.If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, Manufacturer will: (a) Repair or replace the defective goods or part(s) or (b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by Manufacturer. The choice of remedy shall belong to Manufacturer. 2.05.Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the Dealer to the designated factory. 3. LIMITATION OF LIABILITY. 3.01.MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 3.02.MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE GOODS. 3.03.EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER’S LIABILITY HEREUNDER FOR DAMAGES INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS. 3.04.NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED. 4. MISCELLANEOUS. 4.01.Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County, Texas. 4.02.Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term. 4.03.If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein. 4.04.Applicable law may provide rights and benefits to purchaser in addition to those provided herein. KEEP FOR YOUR RECORDS ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification when applying for warranty. Alamo Industrial Implement Model ____________________________ Serial Number ________________________________ Date Purchased __________________________________________ Dealer ______________________________________ ATTENTION: READ YOUR OPERATOR'S MANUAL ALAMO INDUSTRIAL An Alamo Group Company Post Office Drawer 549 Seguin, Texas 78156 830-379-1480 TO THE OWNER/OPERATOR/DEALER To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety requirements of tractor operators: REQUIRED OF THE OWNER: 1. 2. 3. 4. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and Ensure that each employee uses such Seatbelt while the tractor is moving; and Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected area provided by the ROPS. REQUIRED OF THE OPERATOR 1. 2. 3. 4. 5. 6. 7. 8. 9. Securely fasten seatbelt if the tractor has a ROPS. Where possible, avoid operating the tractor near ditches, embankments, and holes. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces. Stay off slopes too steep for safe operation. Watch where you are going - especially at row ends, on roads, and around trees. Do not permit others to ride. Operate the tractor smoothly - no jerky turns, starts, or stops. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer. When the tractor is stopped, set brakes securely and use park lock, if available. Keep children away from danger all day, every day... Equip tractors with rollover protection (ROPS) and keep all machinery guards in place... Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens. Hydro 60 & 7 Printed U.S.A. P/N 02965002P