Transcript
ALCATEL FAST ETHERNET OPTICAL FIBER NETWORK COMPONENTS
▼ 100 Mbps Fast Ethernet transmission system in accordance with IEEE802.3u ▼ Protocol transparent system for manufacturer independent LANs ▼ Investment protection with optical fiber technology for increasing future requirements ▼ End-to-end optical cabling enables migration to future technologies ▼ Standard interfaces in accordance with IEEE802.3u 100BASE-TX and 100BASE-FX ▼ Full duplex transmission (2 x 100 Mbps) up to 2000m ▼ Optional : Full duplex transmission up to 40 km ▼ No active components in the floor distributor
OPTICAL FIBER NETWORK COMPONENTS
100 Mbps FAST ETHERNET The Alcatel product range for Fast Ethernet covers the entire performance spectrum of manufacturer-independent switch and hub technologies operating at 100 Mbps. Centralized optical cabling structures for "Fiber to the Office" or "Fiber to the Desk" are possible by conversion of the standardized twisted-pair interface (100BASE-TX).
Distances up to 40 km The network can be extended over and above the "building area" (300 m) to cover distances of up to 40 km ("campus area").
Singlemode and multimode fibers All components support both singlemode and multimode optical fibers and also the optical connector systems ´SC´ and ´ST´ above the requirements of the standards – a major advantage with respect to "future" technologies. Note: singlemode = SM 9/125 µm, multimode = GI 50/125µm and 62.5/125 µm
Alcatel Fiber Con Key components in the Alcatel product range are the Fiber Con units. These convert switched full-duplex twisted-pair ports (100BASE-TX) bidirectionally into optical fiber ports (100BASE-FX). Without modification of the software, this now makes universal and extremely flexible and powerful collapsed backbone structures possible in optical data networks. It also opens up a wide range of migration possibilities, permitting step-by-step introduction of optical fibers into the network, regardless of whether "Fiber to the Office" or "Fiber to the Desk" is used. The growing market presence of switches, routers and bridges with standard twisted-pair ports clearly demonstrates how economical the Fiber Con solution is. Existing units can be connected directly via TP ports (RJ45) and can be used just as in the past, without any further hardware replacement and independent of the manufacturer. The built-in link signal connection ensures that any faults are passed on to the network management.
Versions Many different versions, such as 6-port and 1-port variants, and easily fitted installation systems are available. The terminal side of the Fiber Con product range is rounded off by desktop units and cable duct modules. Full-duplex operation and protocol transparency are guaranteed, just as for all Fiber Con components. In full-duplex mode, data can be transmitted over distances of up to 2000 m (optionally 40 km).
OPTICAL FIBER NETWORK COMPONENTS
Fiber Con 600 ———————————————————————————————————————————————————— Fiber Con 600 is an advantageous multi-port media converter. Used in central network nodes in the building or campus area, it permits simple extension of a network withoptical fibers, without any problems in the adaptation of the existing software or hardware. The unit can be used directly as a patch panel in 19" rack technology.
Fiber Con 100 Desk ———————————————————————————————————————————————— Fiber Con 100 Desk is a single-port version in a desk-top case which can be used either as a network node or as a terminal port in the office. The built-in power supply unit avoids the problems often related with external, plug-type power supply units and similar devices. The pin assignments of the twisted-pair socket can be modified for the direct connection of either switches or terminals. No special connection cables are needed, regardless of whether it is used as a terminal port in an office or as an extension for a switch port.
Fiber Con 100
———————————————————————————————————————————————————
Fiber Con 100 is a module for installation in standard wall boxes. Functionally, it is identical to the "Desk" version. For connection of terminals, the module can be installed in all commonly used cabling systems such as wall and breastwork ducts. The safe guidance and laying of the optical fibers in cable ducts and twisted-pair terminal sockets emphasize the suitability of this system for use in office and industrial environments.
Fiber Con 100 PC —————————————————————————————————————— Fiber Con 100 PC modules are used in "fiber to the desk" (FTTD) applications. These modules, in the form of plug-in cards for PCs, provide optimum conditions for switching and multimedia applications. Installation is unaffected by the type of bus and consists purely of mechanical insertion and connection of the supply voltage within the PC by means of a special adapter provided with the module. The Fiber Con 100 PC card is connected via an external twisted-pair cable to a Fast Ethernet card (of any make) in the PC.
OPTICAL FIBER NETWORK COMPONENTS
Optical fibers and switching technology in the work place sector These permit the extension of existing or planned cable links without having to worry about the typical length restrictions of Fast Ethernet networks. The permissible segment distance of up to 100 m (Cat. 5) or 412 m (optical fibers) is soon reached in the case of direct terminal connection. Network planning and expansion are made unnecessarily complicated by the need for additional intermediate stages (horizontal distributors, etc.). The Alcatel switch family is the ideal solution here. Switch functions such as netload separation for the network segments and simple handling without the need for software configuration show how useful these units are in the enduser area.
Copper Switch 10/100 Desk ————————————————————————————————————————— The Copper Switch 10/100 multiplies the connection capacity of a data connection (100BASE-TX) by four, i.e. your single RJ45 terminal connection (100BASE-TX) becomes a link for up to four independent terminals. Switchable for 10/100 Mbps.When used together with the Fiber Con 100 media converter, this permits segment lengths of up to 2000 m (optionally 40 km) in full-duplex transmission mode (FDX).The Copper Switch 100 is thus the final element in the low-cost "fiber to the office" (FTTO) solution in combination with Fiber Con.
Fiber Switch 10/100 Desk ——————————————————————————————————————————— The Fiber Switch 100 is also intended for the end-user area. It combines the optical fibers (FX), switch functions and four 10/100 Mbps terminal ports in one unit. Its full-duplex transmission mode and easy handling provide a low-cost and high-performance alternative to conventional "fiber to the desk" (FTTD) solutions.There is no expensive and fault-prone optical cabling to the user terminals and it is not necessary to upgrade the PCs with "optical network cards" or to modify their software.
Optical Fiber and Connection Sharing Fiber Share 100 —————————————————————————————————————————————————— The Fiber Share 100 cable duct module allows multiple users (up to 4) to benefit from one optical fiber connection in Fast Ethernet networks according to IEEE 802.3u 100BASE-FX. By adding a Fiber Share 100 module, an optical connection can quickly and easily serve up to 4 Twisted pair 100 BASE-TX connections.The safe guidance and laying of the optical fibers in cable ducts and twisted-pair terminal sockets emphasize the suitability of this system for use in office and industrial environments. The module can be mounted into all commonly used elektroinstallation systems. The future-proof optical fiber infrastructure offers practically unlimited bandwidths, and allows for connection distances up to 300m.
OPTICAL FIBER NETWORK COMPONENTS
Ordering codes —————————————————————————————————————————————————— Maximum distance IEEE802.3u 100BASE-FX
Up to 2 km
Up to 40 km singlemode only
Fiber Con
media converters with independent 100BASE-TX/FX ports
Fiber Con 600
with 6 ports in a 19" chassis ditto for multimode fibers with SC plug connectors
ACS-606.001
ACS-606.010
ditto for singlemode and multimode fibers with ST
ACS-606.002
ACS-606.011
BFOC/2,5 plug connectors Fiber Con 100
installation module with one TX port ditto for multimode fibers with SC plug connectors
ACS-610.010
ditto for singlemode and multimode fibers with ST
ACS-610.011
BFOC/2,5 plug connectors Fiber Con 100 Desk
desk-top module with one TX port ditto for multimode fibers with SC plug connectors
ACS-610.001
ACS-610.003
ditto for singlemode and multimode fibers with ST
ACS-610.002
ACS-610.004
BFOC/2,5 plug connectors Fiber Con 100 PC
PC card with external link to the network card of the PC ditto for multimode fibers with SC plug connectors
ACS-610.020
ditto for singlemode and multimode fibers with ST
ACS-610.021
BFOC/2,5 plug connectors Fiber Switch
switch with FO uplink port and four 100BASE-TX user ports
Fiber Switch 10/100
desk-top unit for 10/100 Mbps ditto for multimode fibers with SC plug connectors
ACS-611.001
ACS-611.003
ditto for singlemode and multimode fibers with ST
ACS-611.002
ACS-611.004
BFOC/2,5 plug connectors Fiber Share
Hub with FO port and four 100BASE-TX user ports
Fiber Share 100
installation module for 100 Mbps
FX up to 300 m
ditto for multimode fibers with SC plug connectors
ACS-601.051
ditto for singlemode and multimode fibers with ST
ACS-601.052
BFOC/2,5 plug connectors Copper Switch
switch with TX uplink and expansion to four 100BASE-TX
Copper Switch 10/100
user ports desk top unit for 10/100 Mbps user- and uplink ports
* Multimode fibers with the dimensions GI 50/125 or 62.5/125 µm Singlemode fibers with the dimensions SM 9/125 µm
TX up to 100 m ACS-612.001
FIBER CON 600 FAST ETHERNET MEDIA CONVERTER
▼ ▼ ▼ ▼
100 Mbps Fast Ethernet media converter, IEEE802.3u standard Twisted pair <-> optical fiber media converter Six independent, protocol-transparent connection ports Standard interfaces according to IEEE802.3u, 100BASE-TX and 100BASE-FX
▼ Full-duplex transmission (200 Mbps) up to 2000 m ▼ Optional: full-duplex transmission (200 Mbps) up to 40 km ▼ Minimal delay time – influences on the permissible network extent are negligible, no repeater restrictions ▼ No configuration required ▼ Link signal interconnect for monitoring the connection ▼ Status displays for: • ready for operation • FO link and data reception • TP link and data reception ▼ Internal PSU with mains power socket ▼ 19” unit, 1 HU (height = 1.9”), colour RAL 7044 ▼ Connections: • SC or ST optical fiber connection for multimode or singlemode fibers • Shielded RJ45 socket for node connection
FIBER CON 600 FAST ETHERNET MEDIA CONVERTER Fast Ethernet central systems such as switches, routers and hubs are mostly fitted with twisted pair connections these days. With the Alcatel Fiber Con 600 media converter, such systems can be included in optical data networks in an uncomplicated way. The 19” unit converts six independent twisted pair connections (100BASE-TX) into IEEE802.3u-standard 100BASE-FX optical connections. This permits adaptation to a future-proof optical infrastructure with practically unlimited bandwidth, without the 100 m distance limitation of twisted pair cabling. Optical collapsed backbone structures for fiber-to-the-office offer the optimum conditions for switching and multimedia. The Fiber Con 600 media converter supports simultaneous transmission and reception (full-duplex) at 2 x 100 Mbps over distances of up to 2000 m. In half-duplex operation, the maximum extension for compliance with the Fast Ethernet standard is 400 m. These features – standard interfaces for optical fiber and twisted pair, full and half-duplex transmission, status displays and internal power supply – enable you to quickly and easily build up and extend Fast Ethernet networks with optical cabling structures, without any configuration to be done, thus safeguarding your investment.
Versions ——————————————————————————————————————————————————————— Fiber Con 600 FX GI (SC)
Fast Ethernet 6-port FX/TX media converter (19” unit) for multimode fibers with SC connector.
Fiber Con 600 FX SM (ST)
Fast Ethernet 6-port FX/TX media converter (19” unit) for singlemode or multimode fibers with ST connector.
Technical specifications ————————————————————————————————————————————— Unit
Fiber Con 600 FX GI (SC)
Fiber Con 600 FX SM (ST)
VAC - 265VAC / 47..440 Hz
Power supply Power consumption
W
Dimensions (w x h x d)
mm
<32
<32 448 x 44,48(1HU) x 230
6x TX/FX
LAN interfaces
6x TX/FX
according to IEEE802.3u 100BASE-FX
Optical FX interface
full-duplex (FDX) up to 2000m, half-duplex (HDX) up to 400m duplex SC
2x ST BFOC/2.5
1300
1300
dBm
-32
-32
dBm
-
-25
for GI 50/125 µm
dBm
-22
-15
for GI 62.5/125 µm
dBm
-19
-12
Dynamic range for SM 9/125 µm
dB
-
7
for GI 50/125 µm
dB
10
17
for GI 62.5/125 µm
dB
13
20
Transfer interface Wavelength
nm
Input sensitivity Output power for SM 9/125 µm
according to IEEE802.3u 100BASE-TX
Electrical TX interface
full and half-duplex up to 100m
Type of transmission/distance Transfer interface
100 Ohm, RJ45, screened, for terminal unit connection
Ordering Codes —————————————————————————————————————————————————— Fiber Con 600 FX GI (SC)
ACS-606.001
Fiber Con 600 FX SM (ST)
ACS-606.002
ALCATEL CABLING SYSTEMS Bd. Paepsemlaan 16 - 1070 Brussels - Belgium Tel.: 32.2.556.08.50 - Fax: 32.2.556.49.50
Subject to change without prior notice.
Type of transmission/distance
DSE-807-0698-V2.0
Characteristic
FIBER CON 100 FAST ETHERNET MEDIA CONVERTER
▼ 100 Mbps Fast Ethernet media converter, IEEE802.3u standard ▼ Twisted pair <-> optical fiber media converter ▼ Protocol-transparent node connection for mounting in cable raceways and underfloor systems ▼ Standard interfaces according to IEEE802.3u, 100BASE-TX and 100BASE-FX ▼ Full-duplex transmission (200 Mbps) up to 2000 m ▼ Minimal delay time – influences on the permissible network extent are negligible, no repeater restrictions ▼ Link signal interconnect for monitoring the connection ▼ Status displays for: • ready for operation • FO link and data reception • TP link and data reception ▼ Integrated power supply with pin/screw terminals for mains connection ▼ Colour of cover: ivory (standard) ▼ Connections: • SC or ST optical fiber connection for multimode or singlemode fibers • Shielded RJ45 socket for node connection
FIBER CON 100 FAST ETHERNET MEDIA CONVERTER Fast Ethernet network cards for terminal equipment are mostly fitted with twisted pair connections these days. With Alcatel Fiber Con 100 media converter modules, such terminal units can be included in optical data networks without requiring any configuration changes. The Alcatel Fiber Con 100 converts an independent twisted pair node connection (100BASE-TX) into an IEEE802.3u-standard 100BASE-FX optical connection. This permits adaptation to a future-proof optical infrastructure with practically unlimited bandwidth, without the 100 m distance limitation of twisted pair cabling. Optical collapsed backbone structures for fiber-to-theoffice offer the optimum conditions for switching and multimedia. The Fiber Con 100 media converter supports simultaneous transmission and reception (full-duplex) at 2 x 100 Mbps over distances of up to 2000 m. In half-duplex operation, the maximum extension for compliance with the Fast Ethernet standard is 400 m. These features – compatibility with existing electrical systems, standard interfaces for optical fiber and twisted pair, full and halfduplex transmission, status displays and internal power supply – enable you to build up and extend Fast Ethernet networks with optical cabling structures, without software modifications, thus safeguarding your investment.
Versions ——————————————————————————————————————————————————————— Fiber Con 100 FX GI (SC)
Fast Ethernet FX/TX media converter for incorporation in electrical installations for multimode fiber with SC connector.
Fiber Con 100 FX SM (ST)
Fast Ethernet FX/TX media converter for incorporation in electrical installations for singlemode or multimode fiber with ST connector.
Technical specifications ————————————————————————————————————————————— Characteristic
Unit
Fiber Con 100 FX GI (SC)
Fiber Con 100 FX SM (ST)
195...265 VAC/98...132 VAC/47...70 Hz
Power supply
3 pole, pin/screw terminals (N, L1, PE) Power consumption
W
Dimensions (w x h x d)
mm
<5
<5 140 x 70 x 35
1x TX/FX
LAN interfaces
1x TX/FX
according to IEEE802.3u 100BASE-FX
Optical FX interface
2x ST BFOC/2.5
1300
1300
dBm
-32
-32
dBm
-
-25
for GI 50/125 µm
dBm
-22
-15
for GI 62.5/125 µm
dBm
-19
-12
Dynamic range for SM 9/125 µm
dB
-
7
for GI 50/125 µm
dB
10
17
for GI 62.5/125 µm
dB
13
20
Wavelength
nm
Input sensitivity Output power for SM 9/125 µm
according to IEEE802.3u 100BASE-TX
Electrical TX interface
full and half-duplex up to 100m
Type of transmission/distance Transfer interface
100 Ohm, RJ45, screened, for terminal unit connection
Ordering Codes —————————————————————————————————————————————————— Fiber Con 100 FX GI (SC)
ACS-610.010
Fiber Con 100 FX SM (ST)
ACS-610.011
ALCATEL CABLING SYSTEMS Bd. Paepsemlaan 16 - 1070 Brussels - Belgium Tel.: 32.2.556.08.50 - Fax: 32.2.556.49.50
DSE-806-0698-V2.0
duplex SC
Transfer interface
Subject to change without prior notice.
full-duplex (FDX) up to 2000m, half-duplex (HDX) up to 400m
Type of transmission/distance
FIBER CON 100 DESK FAST ETHERNET MEDIA CONVERTER
▼ ▼ ▼ ▼
100 Mbps/Fast Ethernet media converter, IEEE802.3u standard Twisted pair <-> optical fiber media converter Protocol-transparent node connection Standard interfaces according to IEEE802.3u, 100BASE-TX and 100BASE-FX
▼ Full-duplex transmission (200 Mbps) up to 2000 m ▼ Optional: full-duplex transmission (200 Mbps) up to 40 km ▼ Minimal delay time – influences on the permissible network extent are negligible, no repeater restrictions ▼ Link signal interconnect for monitoring the connection ▼ Status displays for: • ready for operation • FO link and data reception • TP link and data reception ▼ Internal PSU with mains power socket ▼ Housing colour: RAL 7044 ▼ Connections: • SC or ST optical fiber connection for multimode or singlemode fibers • Shielded RJ45 socket for node connection on the front of the unit
FIBER CON 100 DESK FAST ETHERNET MEDIA CONVERTER Fast Ethernet network cards for terminal equipment are mostly fitted with twisted pair connections these days. With Alcatel Fiber Con 100 Desk media converter, such terminal units can be included in optical data networks without requiring any configuration changes. The Alcatel Fiber Con 100 Desk converts an independent twisted pair node connection (100BASE-TX) into an IEEE802.3u-standard 100BASE-FX optical connection. This permits adaptation to a future-proof optical infrastructure with practically unlimited bandwidth, without the 100 m distance limitation of twisted pair cabling. Optical collapsed backbone structures for fiber-to-the-office offer the optimum conditions for switching and multimedia. The Fiber Con 100 Desk media converter supports simultaneous transmission and reception (full-duplex) at 2 x 100 Mbps over distances of up to 2000 m. In half-duplex operation, the maximum extension for compliance with the Fast Ethernet standard is 400 m. These features – standard interfaces for optical fiber and twisted pair, full and half-duplex transmission, status displays for every port and internal power supply – enable you to quickly and easily build up and extend Fast Ethernet networks with optical cabling structures, without software modifications, thus safeguarding your investment.
Versions ——————————————————————————————————————————————————————— Fiber Con 100 Desk FX GI (SC)
Fast Ethernet FX/TX media converter in desktop housing for multimode fiber with SC connector.
Fiber Con 100 Desk FX SM (ST)
Fast Ethernet FX/TX media converter in desktop housing for singlemode or multimode fiber with ST connector.
Technical specifications ————————————————————————————————————————————— Unit
Fiber Con 100 Desk FX GI (SC)
Power supply
Fiber Con 100 Desk FX SM (ST)
195...265 VAC / 98...132 VAC / 47..70 Hz
Power consumption
W
Dimensions (w x h x d)
mm
LAN interfaces
<5
<5 104 x 43 x 165
1x TX/FX
Optical FX interface
1x TX/FX
according to IEEE802.3u 100BASE-FX
Type of transmission/distance
full-duplex (FDX) up to 2000m, half-duplex (HDX) up to 400m duplex SC
2x ST BFOC/2.5
1300
1300
dBm
-32
-32
dBm
-
-25
for GI 50/125 µm
dBm
-22
-15
for GI 62.5/125 µm
dBm
-19
-12
Dynamic range for SM 9/125 µm
dB
-
7
for GI 50/125 µm
dB
10
17
for GI 62.5/125 µm
dB
13
20
Wavelength
nm
Input sensitivity Output power for SM 9/125 µm
Electrical TX interface
according to IEEE802.3u 100BASE-TX
Type of transmission/distance Transfer interface
full and half-duplex up to 100m 100 Ohm, RJ45, screened, for terminal unit connection
Ordering Codes —————————————————————————————————————————————————— Fiber Con 100 Desk FX GI (SC)
ACS-610.001
Fiber Con 100 Desk FX SM (ST)
ACS-610.002
ALCATEL CABLING SYSTEMS Bd. Paepsemlaan 16 - 1070 Brussels - Belgium Tel.: 32.2.556.08.50 - Fax: 32.2.556.49.50
Subject to change without prior notice.
Transfer interface
DSE-804-0698-V2.0
Characteristic
FIBER CON 100 PC FAST ETHERNET MEDIA CONVERTER
▼ ▼ ▼ ▼
100 Mbps Fast Ethernet media converter, IEEE802.3u standard Twisted pair <-> optical fiber media converter PC card (ISA, PCI, etc.) for protocol-transparent node connection Standard interfaces according to IEEE802.3u, 100BASE-TX and 100BASE-FX
▼ Full-duplex transmission (200 Mbps) up to 2000 m ▼ Minimal delay time – influences on the permissible network extent are negligible, no repeater restrictions ▼ Link signal interconnect for monitoring the connection ▼ Status displays for: • ready for operation • FO link and data reception • TP link and data reception ▼ Power supply drawn from the PSU of the PC ▼ No modifications necessary to PC setup and no software modifications ▼ PC TX network cards can continue to be used for external connection ▼ Connections: • SC or ST optical fiber connection for multimode or singlemode fibers • Shielded RJ45 socket for TX connection to PC network card
FIBER CON 100 PC FAST ETHERNET MEDIA CONVERTER Fast Ethernet network cards for PCs are mostly fitted with twisted pair connections these days. With an Alcatel Fiber Con 100 PC media converter card, such terminals can be included in optical data networks without requiring any configuration changes. The Alcatel Fiber Con 100 PC converts an independent twisted pair node connection (100BASE-TX) into an IEEE802.3u-standard 100BASE-FX optical connection. This permits adaptation to a future-proof optical infrastructure with practically unlimited bandwidth, without the 100 m distance limitation of twisted pair cabling. Optical collapsed backbone structures for fiber-to-the-office offer the optimum conditions for switching and multimedia. The Fiber Con 100 PC media converter supports simultaneous transmission and reception (full-duplex) at 2 x 100 Mbps over distances of up to 2000 m. In half-duplex operation, the maximum extension for compliance with the Fast Ethernet standard is 400 m. These features – compatibility with the existing network card, standard interfaces for optical fiber and twisted pair, full and halfduplex transmission and status displays for every port – enable you to quickly and easily build up and extend Fast Ethernet networks with optical cabling structures, without software modifications, thus safeguarding your investment.
Versions ——————————————————————————————————————————————————————— Fiber Con 100 PC FX GI (SC)
Fast Ethernet FX/TX media converter for installation in PCs, for multimode fiber with SC connector.
Fiber Con 100 PC FX SM (ST)
Fast Ethernet FX/TX media converter for installation in PCs for singlemode or multimode fiber with ST connector.
Technical specifications ————————————————————————————————————————————— Unit
Power supply
Fiber Con 100 PC FX GI (SC)
Fiber Con 100 PC FX SM (ST)
4,75...5,25 VDC / 350mA / 4pol. standard connector for hard disk drive
Power consumption
W
Dimensions (w x h x d)
mm
<2,5
<2,5 18 x 120 x 65
LAN interfaces
1x TX/FX
Optical FX interface
1x TX/FX
according to IEEE802.3u 100BASE-FX
Type of transmission/distance
full-duplex (FDX) up to 2000m, half-duplex (HDX) up to 400m
Transfer interface
duplex SC
2x ST BFOC/2.5
1300
1300
dBm
-32
-32
dBm
-
-25
for GI 50/125 µm
dBm
-22
-15
for GI 62.5/125 µm
dBm
-19
-12
Dynamic range for SM 9/125 µm
dB
-
7
for GI 50/125 µm
dB
10
17
for GI 62.5/125 µm
dB
13
20
nm
Input sensitivity Output power for SM 9/125 µm
Electrical TX interface
according to IEEE802.3u 100BASE-TX
Type of transmission/distance Transfer interface
full and half-duplex up to 100m 100 Ohm, RJ45, screened, for terminal unit connection
Ordering Codes —————————————————————————————————————————————————— Fiber Con 100 PC FX GI (SC)
ACS-610.020
Fiber Con 100 PC FX SM (ST)
ACS-610.021
ALCATEL CABLING SYSTEMS Bd. Paepsemlaan 16 - 1070 Brussels - Belgium Tel.: 32.2.556.08.50 - Fax: 32.2.556.49.50
Subject to change without prior notice.
Wavelength
DSE-805-0698-V2.0
Characteristic
FIBER SWITCH 10/100 DESK OPTICAL FAST ETHERNET SWITCH
▼ Fast Ethernet switch with four shared node connections, IEEE802.3u standard • Switched optical fiber up-link for 100BASE-FX • Four shared twisted pair node connections for 10/100BASE-TX ▼ Optical fiber up-link connection with configurable operating mode: • Full-duplex transmission (200 Mbps) up to 2000 m • Half-duplex transmission up to 412 m ▼ Optional: full-duplex transmission (200 Mbps) up to 40 km ▼ Twisted pair node connections up to 100 m ▼ Status displays for: • ready for operation • FO up-link and data reception • Full-duplex transmission on optical fiber up-link port • TP link and data reception for each TP node connection ▼ Internal PSU with mains power socket ▼ Housing colour RAL 7044 ▼ Connections: • SC or ST optical fiber connection for multimode or singlemode fibers • Four shielded RJ45 sockets for node connections at the front
FIBER SWITCH 10/100 DESK OPTICAL FAST ETHERNET CONVERTER The Alcatel Fiber Switch 10/100 Desk permits multiple use of IEEE802.3u 100BASE-FX standard Fast Ethernet optical fiber links without length restrictions. By adding an Alcatel Fiber Switch 10/100, an optical node/office connection can quickly and easily be made to serve four twisted pair connections for Fast Ethernet. Full switching functionality and high optical dynamic range permit optical up-link connections up to 2000 m in full-duplex. Thanks to this solution, the considerable advantages of a future-proof optical collapsed backbone cabling structure are already available to you. In half-duplex operation, the maximum extension for Fast Ethernet standard is 412 m. The TP node connections can be configured as 10BASE-T or 100BASE-TX, according to choice, enabling you to build up your network step by step, in a way that safeguards your investment. These features – optical fiber up-link interface, switching function, 10/100 Mbps node connections, status displays for each port and internal power supply – enable you to quickly and easily build up and extend your Fast Ethernet network quickly and easily.
Versions ——————————————————————————————————————————————————————— Fiber Switch 10/100 Desk GI (SC)
Fast Ethernet switch in desktop housing, with optical fiber up-link for multimode fiber with SC connector and four shared TP node connections
Fiber Switch 10/100 Desk SM (ST)
Fast Ethernet switch in desktop housing, with optical fiber up-link for singlemode or multimode fiber with ST connector and four shared TP node connections
Technical specifications ————————————————————————————————————————————— Characteristic
Unit
Power supply
Fiber Switch 10/100 Desk GI (SC)
195VAC - 265VAC / 98VAC - 132VAC / 47..70Hz
Power consumption
W
Dimensions (w x h x d)
mm
<12
<12 104 x 43 x 202
Built-in switch (up-link) Data throughput rate
Fiber Switch 10/100 Desk SM (ST)
Store and forward, self-teaching Pkt/s
max. 148800
Packet/address buffer
1008 / 8000 dynamically managed
LAN interfaces Optical up-link interface
according to IEEE802.3u 100BASE-FX
Type of transmission/distance
full-duplex (FDX) up to 2000 m, half-duplex (HDX) up to 412 m
Transfer interface
duplex SC
2x ST BFOC/2.5
1300
1300
-32
-32
-
7
dB
10
17
dB
13
20
Wavelength
nm
Input sensitivity
dBm
Dynamic range for SM 9/125 µm
dB
for GI 50/125 µm for GI 62.5/125 µm Electrical TP interface to node / network segment
half-duplex up to 100 m 100 Ohm, RJ45, screened, for terminal unit connection
Ordering Codes —————————————————————————————————————————————————— Fiber Switch 10/100 Desk GI (SC)
ACS-611.001
Fiber Switch 10/100 Desk SM (ST)
ACS-611.002
ALCATEL CABLING SYSTEMS Bd. Paepsemlaan 16 - 1070 Brussels - Belgium Tel.: 32.2.556.08.50 - Fax: 32.2.556.49.50
DSE-8080698-V2.0
Transfer interface
Subject to change without prior notice.
according to IEEE802.3u 100BASE-TX
Type of transmission/distance
FIBER SHARE 100 OPTICAL FAST ETHERNET MULTICONNECTOR
▼ ▼ ▼ ▼
100 Mbps Fast Ethernet, IEEE802.3u standard Optical fiber <-> twisted pair node connection module Four protocol-transparent node connections with angled sockets Standard interfaces according to IEEE802.3u, 100BASE-TX and 100BASE-FX
▼ Half-duplex transmission up to 300 m ▼ For mounting in cable raceways and under-floor systems ▼ Status displays for: • ready for operation • FO link and data reception • FO link error • TP link and data reception for each TP node connection ▼ Internal PSU with pin/screw terminals for mains connection ▼ Colour of cover: ivory (standard) ▼ Connections: • SC or ST optical fiber connection for multimode or singlemode fibers • Four shielded RJ45 sockets for node connections at the front
FIBER SHARE 100 OPTICAL FAST ETHERNET MULTICONNECTOR The Alcatel Fiber Share 100 module permits multiple use of IEEE802.3u 100BASE-FX standard Fast Ethernet optical fiber links. By adding an Alcatel Fiber Share 100, an optical node/office connection can quickly and easily be made to serve four twisted pair connections. The four twisted pair connections correspond to standard IEEE802.3u 100BASE-TX, permitting adaptation to a future-proof optical infrastructure in any building, with practically unlimited bandwidth up to distances of 300 m. This compares with the 100 m length restriction for copper cabling. These features – multiple use of a optical fiber link, standard interfaces for optical fiber and twisted pair, status displays for each port and internal power supply – enable you to build up and extend your Fast Ethernet network with optical cabling structures, without software modifications.
Versions ——————————————————————————————————————————————————————— Fiber Share 100 FX GI (SC)
Fast Ethernet FX/4xTX hub for mounting in cable raceways, for multimode fiber with SC connector
Fiber Share 100 FX SM (ST)
Fast Ethernet FX/4xTX hub for mounting in cable raceways, for singlemode or multimode fiber with ST connector
Technical specifications ————————————————————————————————————————————— Characteristic
Unit
Fiber Share 100 FX GI (SC)
Fiber Share 100 FX SM (ST)
195...265 VAC/98...132 VAC/47...70 Hz
Power supply
3 pole, pin/screw terminals (N, L1, PE) Power consumption
W
Dimensions (w x h x d)
mm
<6
<6 140 x 70 x 35
LAN interfaces half-duplex up to 300 m
Type of transmission/distance
according to IEEE802.3u 100BASE-FX
Optical FX interface
duplex SC
2x ST BFOC/2.5
1300
1300
-32
-32
Wavelength
nm
Input sensitivity
dBm
Output power for SM 9/125 µm
dBm
-
-25
for GI 50/125 µm
dBm
-22
-15
for GI 62.5/125 µm
dBm
-19
-12
Dynamic range for SM 9/125 µm
dB
-
7
for GI 50/125 µm
dB
10
17
for GI 62.5/125 µm
dB
13
20 half duplex (HDX) up to 100 m
Type of transmission/distance Transfer interface
100 Ohm, RJ45, screened, for terminal unit connection
Ordering Codes —————————————————————————————————————————————————— Fiber Share 100 FX GI (SC)
ACS-601.051
Fiber Share 100 FX SM (ST)
ACS-601.052
ALCATEL CABLING SYSTEMS Bd. Paepsemlaan 16 - 1070 Brussels - Belgium Tel.: 32.2.556.08.50 - Fax: 32.2.556.49.50
Subject to change without prior notice.
according to IEEE802.3u 100BASE-TX
Electrical TX interface
DSE-809-0698-V2.0
Transfer interface
COPPER SWITCH 100 DESK FAST ETHERNET SWITCH
▼ Fast Ethernet switch with four shared terminal ports in accordance with IEEE802.3u • Switched twisted-pair up-link to 10/100BASE-TX • Four shared twisted-pair terminal ports to 10/100BASE-TX ▼ Twisted-pair up-link can be configured for operation in the modes: • full duplex (2 x 100 Mbit/s) • half duplex ▼ Cable lengths up to 100 m. ▼ Status indicators for: • Ready • TP up-link and received data • Full-duplex mode at TP up-link port ▼ TP link and received data for each TP terminal port ▼ Integrated power supply unit with socket for power cable ▼ Desktop case, colour RAL 7044 ▼ Connections: • Screened RJ45 socket for up-link port on the rear • Four screened RJ45 sockets for terminal ports on the front
COPPER SWITCH 100 DESK FAST ETHERNET SWITCH
The Alcatel Copper Switch 100 Desk in its desktop case permits multiple utilisation of existing connections in a Fast Ethernet network in accordance with IEEE802.3u 100BASE-TX. An optical terminal connection set up with an Alcatel Fiber Con 100 media converter can be expanded quickly and easily to accommodate four terminals with the aid of an Alcatel Copper Switch 100. Similarly, existing twisted-pair connections in structured cabling systems can be extended easily. The combination of an Alcatel Copper Switch 100 and a Fiber Con 100 permits the utilisation of the considerable advantages of the future-oriented optical collapsed-backbone cabling structure. The network can be expanded step-by-step in several stages, which means that today's investments will not lose their value. Switch functionality, standard 10/100 Mbit/s ports with status indicators for each port and the built-in power supply unit guarantee simple and fast erection and expansion of a Fast Ethernet network.
Versions ——————————————————————————————————————————————————————— Copper Switch 100 Desk
Fast Ethernet twisted-pair switch in a desktop case TP up-link and terminal ports Four shared TP
Technical specifications ————————————————————————————————————————————— Comment
Unit
Copper Switch 100 Desk 195 VAC to 265 VAC / 98 VAC to 132 VAC
Supply voltage Supply frequency
Hz
47...70
Power consumption
W
<12
Dimensions (w x h x d)
mm
104 x 43 x 202 Store and forward, self-learning
Integrated switch (up-link) Data throughput
Pkt/s
max. 148800
Packet buffers
1008, managed dynamically
Entries in addresstable
8000, managed dynamically
LAN interfaces Electrical TP interface, up-link Input/output signals
To IEEE802.3u 100BASE-TX
Transmission mode
Full duplex (FDX) or half duplex (HDX) 100 Ohm, RJ45, screened, switch port
Transfer interface Cable length
max. 100
m
Electrical TP interface to terminal or network segment To IEEE802.3u 100BASE-TX
Input/output signals
Half duplex (HDX)
Transmission mode
100 Ohm, RJ45, screened, for terminal port
Transfer interface
Ordering Codes —————————————————————————————————————————————————— Copper Switch 100 Desk
ACS-612.001
ALCATEL CABLING SYSTEMS Bd. Paepsemlaan 16 - 1070 Brussels - Belgium Tel.: 32.2.556.08.50 - Fax: 32.2.556.49.50
Subject to change without prior notice.
max. 100
m
DSE-810-0698-V2.0
Cable length
FIBER CON 6 ETHERNET MEDIA CONVERTER
▼ Fiber Optic (FO) Twisted Pair (TP) LAN media converter. ▼ 6 independent, protocol-transparent ports. ▼ Full duplex operation of each port (20 Mbit/s) ▼ Minimum delaytime - influence on possible link length can be neglected, no additional restrictions in maximum number of repeaters. ▼ Link fault function for monitoring the connected links. ▼ Compliance with IEEE 802.3 10BASE-FL and 10BASE-T Standard. ▼ Status indicators "data" respectively "link" for each FO and TP port. ▼ Optical Interface with high dynamic range up to 2000m. ▼ No configuration settings required. ▼ 19" rack mount unit, 1 HU (High=44,45mm). ▼ Connectors : • Fiber Optic ST-connectors BFOC/2.5 on the front of the Fiber Con 6 • Screened RJ45 connectors on the front of the Fiber Con 6.
FIBER CON 6 Most of the active Ethernet components as hubs, routers or switches of today are equipped with Twisted Pair interfaces for copper cables. Using the Alcatel Fiber Con Media Converters, the enormous advantages of future save optical collapsed backbones are available immediately. The media converters Alcatel Fiber Con convert the 10BASE-T ports of active Ethernet equipment in optical ports according to 10BASE-FL standard. They realize your adaption to a future save optical infrastructure with nearly unlimited bandwidth and without the 100m link length limitation of copper cabeling. Consequently the optical collapsed backbone structures for Fiber to the Office and Fiber to the Desk can be established, which offer optimum conditions for switching and multimedia. The media converters Fiber Con are supporting the full duplex transmission mode, this means it is possible to receive and transmit simultaneously with 20 Mbit/s throughput. Clear indication of power supply, data transmission and link status by indicators for each port. Because of the minimum delay of Fiber Con the maximum distance in the collision domain and the maximum number of repeaters are not influenced.
Versions Fiber Con 6
6 port media-converter for Multimode Fiber
Fiber Con 6 SM
6 port media-converter for Singlemode and Multimode Fiber
Technical Data Comment
unit
Input range
Fiber Con 6
Fiber Con 6 SM
85 VAC to 264 VAC; 120 to 370 VDC
Power consumption Dimensions
VA
< 15
hxwxd
44.48 (1 HU), 448 (482.6 = 19"), 230
LAN interfaces optical interfaces
6 x Fiber Optic
input/output signals
in accordance with IEEE802.3 10BASE-FL/FOIRL
wavelength Receiver sensibility
nm
850
dBm
min. -32.5
min. output power Multimode Fiber, 50/125 µm
dBm
-21
Multimode Fiber, 62,5/125 µm
dBm
-17
Singlemode Fiber, 9/125 µm
dBm
-12.5 -8.5 -27.5
min. Dynamic range Multimode Fiber, 50/125 µm
dB
11.5
20
Multimode Fiber, 62,5/125 µm
dB
15.5
24
Singlemode Fiber, 9/125 µm
dB
Optical connector
5 ST-connector BFOC/2.5, optional SC-connector
electrical interfaces input/output signals impedance
RJ45, screened Ω
100
Ordering Codes Fiber Con 6
ACS-609.001
Fiber Con 6 SM
ACS-609.011
ALCATEL CABLING SYSTEMS Bd.Paepsemlaan 16 - 1070 Brussels - Belgium Tel.: 32.2.556.08.50 - Fax: 32.2.556.49.50
DSE-361-0298-V2.0 Subject to change without prior notice.
in accordance with IEEE802.3 10BASE-T
connectors
FIBER CON 12 ETHERNET MEDIA CONVERTER
▼ Fiber Optic (FO) Twisted Pair (TP) LAN media converter. ▼ 12 independent, protocol-transparent ports. ▼ Full duplex operation of each port (20 Mbit/s) ▼ Minimum delaytime - influence on possible link length can be neglected, no additional restrictions in maximum number of repeaters. ▼ Link fault function for monitoring the connected links. ▼ Compliance with IEEE 802.3 10BASE-FL and 10BASE-T Standard. ▼ Status indicators "data" respectively "link" for each FO and TP port. ▼ Optical Interface with high dynamic range up to 2000m. ▼ No configuration settings required. ▼ 19" rack mount unit, 1 HU (High=44,45mm). ▼ Connectors : • Fiber Optic ST-connectors BFOC/2.5 on the front of the Fiber Con 12 • Twisted Pair : 50 pins. TELCO Champ connector (RJ-71) on the back of the • Fiber Con 12.
FIBER CON 12 Most of the active Ethernet components as hubs, routers or switches of today are equipped with Twisted Pair interfaces for copper cables. Using the Alcatel Fiber Con Media Converters, the enormous advantages of future save optical collapsed backbones are available immediately. The media converters Alcatel Fiber Con convert the 10BASE-T ports of active Ethernet equipment in optical ports according to 10BASE-FL standard. They realize your adaption to a future save optical infrastructure with nearly unlimited bandwidth and without the 100m link length limitation of copper cabeling. Consequently the optical collapsed backbone structures for Fiber to the Office and Fiber to the Desk can be established, which offer optimum conditions for switching and multimedia. The media converters Fiber Con are supporting the full duplex transmission mode, this means it is possible to receive and transmit simultaneously with 20 Mbit/s throughput. Clear indication of power supply, data transmission and link status by indicators for each port. Because of the minimum delay of Fiber Con the maximum distance in the collision domain and the maximum number of repeaters are not influenced.
Versions Fiber Con 12
12 port media-converter for Multimode Fiber
Fiber Con 12 SM
12 port media-converter for Singlemode and Multimode Fiber
Technical Data Comment
unit
Input range
Fiber Con 12
Fiber Con 12 SM
85 VAC to 264 VAC; 120 to 370 VDC
Power consumption Dimensions
VA
< 15
hxwxd
44.48 (1 HU), 448 (482.6 = 19"), 230
LAN interfaces optical interfaces
12 x Fiber Optic
input/output signals
in accordance with IEEE802.3 10BASE-FL/FOIRL
wavelength Receiver sensibility
nm
850
dBm
min. -32.5
min. output power Multimode Fiber, 50/125 µm
dBm
-21
Multimode Fiber, 62,5/125 µm
dBm
-17
Singlemode Fiber, 9/125 µm
dBm
-12.5 -8.5 -27.5
min. Dynamic range Multimode Fiber, 50/125 µm
dB
11.5
20
Multimode Fiber, 62,5/125 µm
dB
15.5
24
Singlemode Fiber, 9/125 µm
dB
Optical connector
5 ST-connector BFOC/2.5, optional SC-connector
electrical interfaces input/output signals impedance
TP-interface 50 pin TELCO RJ71, screened Ω
100
Ordering Codes Fiber Con 12
ACS-609.001
Fiber Con 12 SM
ACS-609.011
ALCATEL CABLING SYSTEMS Bd.Paepsemlaan 16 - 1070 Brussels - Belgium Tel.: 32.2.556.08.50 - Fax: 32.2.556.49.50
DSE-361-0298-V2.0 Subject to change without prior notice.
in accordance with IEEE802.3 10BASE-T
connectors
