Transcript
ALL168212 QIG
ALL168212 200M Pass-through Adapter
ALLNET GmbH © 2010 www.allnet.de
ALL168212 QIG
Quick Installation Guide Introduction The Wall Mount Powerline Ethernet Bridge can be used to bridge any Ethernet device to your powerline networking with 200Mbps high speed, better than wired 10/100Mbps speed. Integrated with Power Socket, user can directly plug another power device on the Powerline 200M adapter. Built-in filter, can avoid the electric interference from power device.
LEDs for Powerline Networking Status Our Product is compliant with EuP(ErP) Directive, the LED instruction is as follows. LEDStateDescription ONPowerline network activity.Powerline Powerline Link Status;
Ethernet
OFF ON
Flashing OFF
POWER
Green – Good Orange – Normal Red – Poor Search or no Powerline network activity. Ethernet connection is OK.
Auto switch to Normal Mode. Data transferring. No Ethernet link. *Auto switch to Standby Mode after 2 second while No Ethernet Link. Power on. *Auto flashing every 0.5 second when switch to
ON ON
OFF
Standby mode. Powerline off or failure.
Note: * Standby mode: This mode is the energy saving mode, comply with EuP(ErP) Directive. This device will automatically enable the Standby mode when no Ethernet Link is established.
Package Content ‧ ‧ ‧
Wall Mount Powerline Pass-through adapter Quick installation guide Powerline management utility CD Ethernet cable
‧ ALLNET GmbH © 2010 www.allnet.de
ALL168212 QIG
Interface Description
Ethernet
Where you will connect 10/100M Ethernet network devices, such as PCs, printer servers, and anything else you want to put on your networks.
Secure
Please make sure press this button > 10 sec till all LEDs re-flash for each device to generate a random network password first. When each devices get the new random network password, please press one device's secure button < 3 sec first and then press another device secure button < 3 sec, the two devices will auto group. It will easy secure your home powerline network. All
the operations must be completed otherwise timed out after 2 minutes.
Reset
Reset the device to factory default. Please remove the Ethernet cable from RJ-45 Connector before you press the button. Please press the button < 3 sec, the device will auto reset.
Unplug the Ethernet Cable before pressing the Reset button.
ALLNET GmbH © 2010 www.allnet.de
ALL168212 QIG
Installation 1. Simply plug into a power outlet and do not use a power strip or UPS with the wall mount device. 2. Use a twisted-pair cable with RJ-45 plugs at both ends, and plug into Ethernet device and Ethernet of Powerline Bridge.
Warning This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Important Safety Instructions This product is intended for connection to the AC power line. The following pre-cautions should be taken when using this product: ‧ Please read all instructions before installing and operating this product. ‧ Please follow all warnings and instructions marked on the product. ‧ Do not operate this product near water. ‧ This product should never be place near or over radiator, or heat register. ‧ This product relies on a building's electrical installation for short-circuit (over current) protection.
‧ Ensure that a fuse or circuit breaker is used on the phase conductors (all current-carrying conductors). ‧ Do not allow anything to reset on the product interconnect cords. ‧ Do not locate this product where people may walk on the cords. ‧
The power cord should be plugged directly into a specification AC wall outlet. ‧
Only a qualified technician should service this product. Opening or removing covers may result in exposure to dangerous voltage points or other risk. ‧ Unplug this product from the wall outlet and refer the product to qualified service personal for the following conditions: 1. When the interconnect cords are damaged or frayed. 2. If liquid has been spilled onto the product. 3. If the product has been exposed to rain or water. 4. If the product does not operate normally when the operating
instructions have been followed. 5. If the product exhibits a distinct change in performance.
ALLNET GmbH © 2010 www.allnet.de
ALL168212 QIG
WEEE Directive & Product Disposal
At the end of its serviceable life, this product should not be treated as household or general waste. It should be handed over to the applicable collection point for the recycling of electrical and electronic equipment, or returned to the supplier for disposal.
ALLNET GmbH © 2010 www.allnet.de
ALL168212 QIG
EC – Declaration of conformity
This device complies with the essential requirements of the EMC Directives of 2004/108/EC, 92/31/EEC and 93/68/EEC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the EMC Directives of 2004/108/EC, 92/31/EEC and 93/68/EEC.
For the evaluation of above mentioned Harmonised Standards, the following technical and test standards were applied:
EN 55022: 1998+A1: 2000+A2: 2003 Class A EN 61000-3-2: 2000+A2: 2005
EN 61000-3-3: 1995+A1: 2001+A2: 2005
EN 55024: 1998+A1 : 2001+A2: 2003
EN 61000-4-2: 1995+A1: 1998+A2: 2001
EN 61000-4-3: 2002+A1: 2002
EN 61000-4-4: 2004
EN 61000-4-5: 1995+A1: 2001
EN 61000-4-6: 1996+A1: 2001
EN 61000-4-8: 1993+A1: 2001
EN 61000-4-11: 2004
This device is herewith confirmed to comply with the requirements set out in the Council Directive on the harmonization of the Laws of the Member States relating to electrical equipment designed for use within certain voltage limits (2006/95/EC). For the evaluation of above mentioned Directives, the following standards were applied:
IEC 60950-1: 2001
EN 60950-1: 2001 +A11: 2004
This equipment is intended to be operated in all countries. This declaration is made by
ALLNET Computersysteme GmbH Maistraße 2 82110 Germering Germany
and can be downloaded from http://www.allnet.de/ce-certificates/
ALLNET GmbH © 2010 www.allnet.de
ALL168212 QIG
Copyright © 2010. All rights reserved. No part of this document may be reproduced, republished, or retransmitted in any form or by any means whatsoever, whether electronically or mechanically, including, but not limited to, by way of photocopying, recording, information recording, or through retrieval systems without the express written permission of the owner. Product specifications contained in this document are subject to change without notice. All other company or product names mentioned are used for identification purposes only and may be trademarks of their respective owners.
Manufacturer: ALLNET GmbH
ALLNET Deutschland GmbH Maistrasse 2 82110 Germering Tel. +49 89 894 222 22 Fax +49 89 894 222 33 E-Mail:
[email protected]
ALLNET GmbH © 2010 www.allnet.de
