Transcript
ALS-368L
Operating and safety instructions 3.6V Li-ion cordless screwdriver
Attention!
Always follow the safety rules and instructions in this manual. The manufacturer will not accept any responsibility for damage or injury caused by improper use or not in keeping with the requirements of the operating instructions of this tool.
Diagram No.
Descriptions
01 02 03 04
Bit insertion Direction swtich Led light Trigger
05 06 07 08 09 10
Charging receptacle Plug protector Charging adapter 10pcs bit set Bit holder Drill bit
Foreword This brand new 3.6V Li-ion cordless screwdriver is designed for driving tighten and loosen screws. Its built-in new battery technology and more efficient motor make cordless screwdriver to increase working time, greater power, lighter weight, long cycle life,
no memory effect or self discharge when not in use, less pollution. This handy tool withegregious soft grip handle and LED light for poorly lit areas ensure to enjoy works as well as enjoy your life.
Technical data Model
ALS-368L
Dimension Rated voltage No-load speed. Max. torque Screw diameter Weight
158mm x 120mm x 43mm DC 3.6V max. 180 rpm 6.0 Nm max. 5 mm 320g
Battery Capacity Charging time approx.
1.3 Ah 3 Hr.
Battery charger Input Output
AC 230V, 50Hz DC 4.5V, 400mAH
General Safety Rules WARNING! Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains operated (corded) power tool or battery operated (cordless) power tool.
FOLLOW THESE INSTRUCTIONS 1) Work area a) Keep work area clean and well lit. Cluttered and dark areas invited accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c)
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
2) Electrical safety a) Charging adapter plug must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c)
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. 3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c)
Avoid accidental starting. Ensure the switch is in the off position before plugging in the charger. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents.
d) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. e) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. 4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c)
Disconnect the charger plug from the power source before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e) If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
g) Use the power tool, accessories and tool bits etc., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
h) Release trigger switch immediately when a screw is Fastened withy no rotating.Stop pushing trigger when Loosening a screw with no turing within 5 seconds. Improper stress on a cordless screwdriver will cause dmage to motor. 5) Battery tool use and care a) This is a built-in type battery screwdriver,if something damaged,do not attempt to open the housing of this screwdriver,take it to a skilled service center. b) Recharge only with the charger specified by the manufacturer. A charger suitable for one type of screwdriver may create a risk of fire when used with another screwdriver. c)
Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
e) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. 6) Service a) Have your power tool repaired only by qualified personnel using original spare parts. This will ensure that
the safety of the power tool is maintained.
Additional safety instructions WARNING! Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. ■ This Li-ion cordless screwdriver is designed built-in battery. Do not attempt to open or disassemble the battery or remove any component projecting from the battery terminal. There is danger of a short circuit, fire or injury may result. Prior to recycling, protect exposed terminals with heavy insulating tape to prevent shorting.
■
Store idle tool in a cool, dry place where they are protected from frost. Do not store this tool where temperatures may exceed 120°F (49°C) such as in a vehicle, domestic heaters, direct sunlight or metal building during the summer. Temperatures of >50°C < -5°C and high moisture levels will damage the battery pack. There is risk of explosion.
■
Hold the tool with a firm grip. High reaction torque can briefly occur while driving in and loosening screws. Also use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work piece by hand or against your body is unstable and may lead to loss of control.
■
Do not exceed the maximum driving torque. You are recommended to leave it to cool down, if the tool overheats or driving times stipulated.
Safety rules for battery charger ■
Do not expose battery charger to rain, moisture or snow. The penetration of water in a battery charger increases the risk of electric shock.
■
Keep the battery charger terminal clean. Contamination may cause the danger of electric shock
■
Do not operate battery charger with damaged cord or plug. Do not open the battery charger yourself and have it repaired only by qualified personnel using original spare parts. Damaged battery chargers, cables and plugs increase the risk of electric shock.
■
Do not operate the battery charger on easily inflammable surfaces (e.g. paper, textiles, etc.) or combustible environments. There is danger of fire due to the heating of the battery charger during charging.
Battery charging instructions ■
The battery charger supplied is matched to the Li-ion battery built-in the tool. Any other battery charger is forbidden.
■
The battery for this tool is shipped partially charged and must be completely charged prior to first time using and follow the charging instructions. The Li-ion battery can be charged at any time without reducing its service life. Interrupting the charging procedure does not damage the battery.
■
The Li-ion battery is protected against deep discharging. When the battery is hungry, the LED on the switch flash twice by means of protective circuit. The tool holder no longer rotates Note! If the On/Off switch is subject to continued use, the Li-ion battery can be damaged.
■
The charging procedure starts as soon as the mains plug the charger into the AC socket and plug the battery charger terminal into the connector. The LED on switch lights up to indicate the charging procedure. The LED blinks by means of the battery is fully charged.
■
It is normal for the handle of the machine to warm up during the charging procedure.
■
If the battery is warm (after being used or if exposed to the sun etc.) let it cool down prior to charge.
■
Do not charge the battery when the temperature is below 0°C or above 35°C.
■
Never connect the battery charger to a three-phase supply, motor-powered generator or DC power source.
■
Disconnect the battery charger from the socket when not using it for extended periods.
Operation instructions ■
Installing bits: The required screwdriver bit is pushed into
holder.
Note! Use attached bit holder to hold 25 mm
bits,do not use double-end crewdriver bits which are long than 25mm.
■
Caution! Apply the power tool to the screw/nut only when it is switched off.
■
On/Off switch: To switch on the screwdriver by pressing On/Off switch and keep it depressed. The head LED lights up when “switch on” enable to illuminate poorly area.
Release the
switch ,the screwdriver will stop and head LED extinguish within 30 seconds. Also the trigger lights up when switch on,and it extinguish at the itme of releasing switch.
■
Direction of rotation: Push the rotation direction switch onward for clockwise rotation, and backward for left anti-clockwise rotation.
■
Spindle locking: When the On/Off switch is released or set up rotation direction switch to “0”, the is locked. This enables screws to be screwed in, even when the battery is empty and allows for the using as a manually screwdriver.
■
Attention! Use only screwdriver bits that fit properly in the head of the screw. And, when driving in larger and/or longer screws in hard workpieces, it is advisable to drill a pilot hole first.
Maintenance ■
This Li-ion cordless screwdriver is maintenance-free.
■
Store idle tool in a cool, dry place where they are protected from frost. Do not store this tool where temperatures may exceed 120°F (49°C) such as in a vehicle, domestic heaters, direct sunlight or metal building during the summer. Temperatures of >50°C < -5°C and high moisture levels will damage the battery pack. There is risk of explosion.
Environmental protection Recycle raw materials instead of disposing as waste The machine, accessories and packaging should be sorted for environmental-friendly recycling. Waste of the power tool or battery should not be disposed into household waste, fire or water. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice. Defective or worn out batteries must be recycled according to the guidelines 91/157/EEC. To remove the battery from the machine, actuate the On/Off switch until the battery is fully discharged. Disconnect the connections at the battery and remove the battery. Prior to recycling, protect exposed terminals with heavy insulating tape to prevent shorting. EC-Declaration of Conformity
We :
AEBOS Technology Co. Ltd.
60851 No. 67, Chung Cheng Rd, Shuishang Hsiang Chia Yi County, Taiwan, R.O.C. here with declare that the following machine complies with the appropriate basic safety and health requirements of the EC Directive based on its design and type, as brought into circulation by us. In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity.
Machine Description: Machine type: Applicable EC Directives:
Applicable harmonized standards:
3.6V Li-ion cordless screwdriver ALS-368L 98/37/EC 73/23/EEC 89/336/EEC EN 60745 (Battery powered product) EN 55014-1; EN 55014-2 EN 60335 (Battery charger)
Date/Authorized signature: 30/08/09 General Manager
